* Regression in skge that started around acb42a3 (so past v3.3-rc1)
@ 2012-01-30 15:58 Konrad Rzeszutek Wilk
2012-01-30 16:38 ` Stephen Hemminger
0 siblings, 1 reply; 9+ messages in thread
From: Konrad Rzeszutek Wilk @ 2012-01-30 15:58 UTC (permalink / raw)
To: shemminger, netdev, davem; +Cc: linux-kernel
I hadn't done any git bisection yet, but with acb42a3 I started getting this:
(and only on i686 - x86_64 does not show these):
(This is with Xen, the other one is without)
[ 28.602121] eth2: no IPv6 routers present
[ 70.457712] eth2: hw csum failure.
[ 70.458695] Pid: 0, comm: swapper/0 Not tainted 3.3.0-rc1-00287-gacb42a3 #1
[ 70.
[ 70.458695] [<c140942b>] __skb_checksum_complete+0xb/0x10
[ 70.458695] [<c148e3b0>] nf_ip_checksum+0x60/0x120
[ 70.458695] [<c143ee6b>] udp_error+0xbb/0x1f0
[ 70.458695] [<c103c1e4>] ? check_events+0x8/0xc
[ 70.458695] [<c103c1db>] ? xen_restore_fl_direct_reloc+0x4/0x4
[ 70.458695] [<c11497ee>] ? put_cpu_partial+0x9e/0xb0
[ 70.458695] [<c143edb0>] ? udp_pkt_to_tuple+0x60/0x60
[ 70.458695] [<c143a2b6>] nf_conntrack_in+0xc6/0x5c0
[ 70.458695] [<c14751f8>] ? __udp4_lib_rcv+0x428/0x630
[ 70.458695] [<c1149dd0>] ? kfree+0xf0/0x120
[ 70.458695] [<c1405b60>] ? skb_release_data+0x90/0xb0
[ 70.458695] [<c1405b60>] ? skb_release_data+0x90/0xb0
[ 70.458695] [<c14057d8>] ? __kfree_skb+0x38/0x90
[ 70.458695] [<c144d510>] ? inet_del_protocol+0x30/0x30
[ 70.458695] [<c148f41e>] ipv4_conntrack_in+0x1e/0x30
[ 70.458695] [<c14360d3>] nf_iterate+0x63/0x90
[ 70.458695] [<c144d510>] ? inet_del_protocol+0x30/0x30
[ 70.458695] [<c1436292>] nf_hook_slow+0x62/0x140
[ 70.458695] [<c144d510>] ? inet_del_protocol+0x30/0x30
[ 70.458695] [<c144dbb5>] ip_rcv+0x235/0x310
[ 70.458695] [<c144d510>] ? inet_del_protocol+0x30/0x30
[ 70.458695] [<c1412c36>] __netif_receive_skb+0x1d6/0x550
[ 70.458695] [<c147c6a9>] ? inet_gro_receive+0x59/0x1f0
[ 70.458695] [<c1413312>] netif_receive_skb+0x22/0x90
[ 70.458695] [<c1413487>] napi_skb_finish+0x37/0x50
[ 70.458695] [<c14139e3>] napi_gro_receive+0xe3/0xf0
[ 70.458695] [<c12ff4c0>] ? xen_swiotlb_map_sg+0x20/0x20
[ 70.458695] [<c12ff4d9>] ? xen_swiotlb_unmap_page+0x19/0x20
[ 70.458695] [<f7983d6c>] skge_poll+0x34c/0x6f4 [skge]
[ 70.458695] [<c141431a>] net_rx_action+0xfa/0x2a0
[ 70.458695] [<c107cecf>] __do_softirq+0x9f/0x210
[ 70.458695] [<c107ce30>] ? irq_exit+0xd0/0xd0
[ 70.458695] <IRQ> [<c107ce15>] ? irq_exit+0xb5/0xd0
[ 70.458695] [<c12f4ac0>] ? xen_evtchn_do_upcall+0x20/0x30
[ 70.458695] [<c153b157>] ? xen_do_upcall+0x7/0xc
[ 70.458695] [<c10023a7>] ? hypercall_page+0x3a7/0x1000
[ 70.458695] [<c103b802>] ? xen_safe_halt+0x12/0x20
[ 70.458695] [<c104c53d>] ? default_idle+0xfd/0x200
[ 70.458695] [<c103c1db>] ? xen_restore_fl_direct_reloc+0x4/0x4
[ 70.458695] [<c1043fd8>] ? cpu_idle+0xa8/0xf0
[ 70.458695] [<c151658b>] ? rest_init+0x7b/0x80
[ 70.458695] [<c16f886d>] ? start_kernel+0x348/0x34e
[ 70.458695] [<c16f834f>] ? kernel_init+0x149/0x149
[ 70.458695] [<c16f80ba>] ? i386_start_kernel+0xa9/0xb0
[ 70.458695] [<c16fb3b1>] ? xen_start_kernel+0x5f2/0x5fa
[ 70.458695] [<c1409076>] ? memcpy_fromiovecend+0x76/0x80
^G^G^G^G^G^G^G^G^G^G^G^G^G^G^G^G^G^G^G^G^G^G^G^G^G^G^G^G^G^G^G^G^G^G^G^G^G^G failed.
[FAILED]
which now look like this:
[ 288.735236] IP: [<c127b1aa>] memcpy+0x1a/0x0a4f001 *pde = 0000000000000000
[ 288.735236] Oops: 0000 [#1] PREEMPT SMP
[ 288.751724] Modules linked in: dm_multipath dm_mod iscsi_boot_sysfs iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi libcrc32c crc32c sg sd_mod ata_generic sata_nv nouveau fbcon tileblit font bitblit e1000 softcursor ttm libata skge drm_kms_helper mxm_wmi video wmi scsi_mod [last unloaded: dump_dma]
[ 288.751724]
[ 288.751724] Pid: 0, comm: swapper/0 Tainted: G O 3.3.0-rc1-00383-g0a96265 #1 BIOSTAR Group N61PB-M2S/N61PB-M2S
[ 288.751724] EIP: 0060:[<c127b1aa>] EFLAGS: 00010217 CPU: 0
[ 288.751724] EIP is at memcpy+0x1a/0x40
[ 288.751724] EAX: f0a11040 EBX: 00000062 ECX: 00000018 EDX: 00000000
[ 288.751724] ESI: 00000000 EDI: f0a11040 EBP: f100bf2c ESP: f100bf20
[ 288.751724] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[ 288.751724] Process swapper/0 (pid: 0, ti=f100a000 task=c16b1020 task.ti=c16aa000)
[ 288.751724] Stack:
[ 288.751724] f1297c00 f1086144 f762dd80 f100bf88 f8449ccb 39e70110 00000043 39e70110
[ 288.751724] 00000043 00000000 c176b140 00000002 f100bf98 f0991d80 f1297c00 f11c4060
[ 288.751724] ffff0000 00000040 f1297c08 f1297800 00000000 00000000 00000062 f1297c08
[ 288.751724] Call Trace:
[ 288.751724] [<f8449ccb>] skge_poll+0x2ab/0x6f4 [skge]
[ 288.751724] [<c1413dba>] net_rx_action+0xfa/0x2a0
[ 288.751724] [<c107cecf>] __do_softirq+0x9f/0x210
[ 288.751724] [<c107ce30>] ? irq_exit+0xd0/0xd0
[ 288.751724] <IRQ>
[ 288.751724] [<c107ce15>] ? irq_exit+0xb5/0xd0
[ 288.751724] [<c1045e06>] ? do_IRQ+0x46/0xb0
[ 288.751724] [<c107cdc1>] ? irq_exit+0x61/0xd0
[ 288.751724] [<c105fb23>] ? smp_apic_timer_interrupt+0x53/0x90
[ 288.751724] [<c153abb0>] ? common_interrupt+0x30/0x38
[ 288.751724] [<c10685f5>] ? native_safe_halt+0x5/0x10
[ 288.751724] [<c104c53d>] ? default_idle+0xfd/0x200
[ 288.751724] [<c104c68c>] ? amd_e400_idle+0x4c/0x100
[ 288.751724] [<c1043fd8>] ? cpu_idle+0xa8/0xf0
[ 288.751724] [<c151602b>] ? rest_init+0x7b/0x80
[ 288.751724] [<c16f686d>] ? start_kernel+0x348/0x34e
[ 288.751724] [<c16f634f>] ? kernel_init+0x149/0x149
[ 288.751724] [<c16f60ba>] ? i386_start_kernel+0xa9/0xb0
[ 288.751724] Code: c6 43 4c 04 88 43 4d 8b 1c 24 89 ec 5d c3 90 90 90 55 89 e5 83 ec 0c 89 1c 24 89 cb 89 74 24 04 c1 e9 02 89 d6 89 7c 24 08 89 c7 <f3> a5 89 d9 83 e1 03 74 02 f3 a4 8b 1c 24 8b 74 24 04 8b 7c 24
[ 288.751724] EIP: [<c127b1aa>] memcpy+0x1a/0x40 SS:ESP 0068:f100bf20
[ 288.751724] CR2: 0000000000000000
[ 288.972094] ---[ end trace dca3e5f32515fe5d ]---
[ 288.976724] Kernel panic - not syncing: Fatal exception in interrupt
[ 288.983094] panic occurred, switching back to text console
Any thoughts on which patch might be the culprit?
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: Regression in skge that started around acb42a3 (so past v3.3-rc1)
2012-01-30 15:58 Regression in skge that started around acb42a3 (so past v3.3-rc1) Konrad Rzeszutek Wilk
@ 2012-01-30 16:38 ` Stephen Hemminger
2012-01-30 17:22 ` Eric Dumazet
2012-01-30 17:57 ` Konrad Rzeszutek Wilk
0 siblings, 2 replies; 9+ messages in thread
From: Stephen Hemminger @ 2012-01-30 16:38 UTC (permalink / raw)
To: Konrad Rzeszutek Wilk; +Cc: netdev, davem, linux-kernel
On Mon, 30 Jan 2012 10:58:16 -0500
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> wrote:
> I hadn't done any git bisection yet, but with acb42a3 I started getting this:
>
> (and only on i686 - x86_64 does not show these):
>
> (This is with Xen, the other one is without)
> [ 28.602121] eth2: no IPv6 routers present
> [ 70.457712] eth2: hw csum failure.
> [ 70.458695] Pid: 0, comm: swapper/0 Not tainted 3.3.0-rc1-00287-gacb42a3 #1
> [ 70.
> [ 70.458695] [<c140942b>] __skb_checksum_complete+0xb/0x10
> [ 70.458695] [<c148e3b0>] nf_ip_checksum+0x60/0x120
> [ 70.458695] [<c143ee6b>] udp_error+0xbb/0x1f0
> [ 70.458695] [<c103c1e4>] ? check_events+0x8/0xc
> [ 70.458695] [<c103c1db>] ? xen_restore_fl_direct_reloc+0x4/0x4
> [ 70.458695] [<c11497ee>] ? put_cpu_partial+0x9e/0xb0
> [ 70.458695] [<c143edb0>] ? udp_pkt_to_tuple+0x60/0x60
> [ 70.458695] [<c143a2b6>] nf_conntrack_in+0xc6/0x5c0
> [ 70.458695] [<c14751f8>] ? __udp4_lib_rcv+0x428/0x630
> [ 70.458695] [<c1149dd0>] ? kfree+0xf0/0x120
> [ 70.458695] [<c1405b60>] ? skb_release_data+0x90/0xb0
> [ 70.458695] [<c1405b60>] ? skb_release_data+0x90/0xb0
> [ 70.458695] [<c14057d8>] ? __kfree_skb+0x38/0x90
> [ 70.458695] [<c144d510>] ? inet_del_protocol+0x30/0x30
> [ 70.458695] [<c148f41e>] ipv4_conntrack_in+0x1e/0x30
> [ 70.458695] [<c14360d3>] nf_iterate+0x63/0x90
> [ 70.458695] [<c144d510>] ? inet_del_protocol+0x30/0x30
> [ 70.458695] [<c1436292>] nf_hook_slow+0x62/0x140
> [ 70.458695] [<c144d510>] ? inet_del_protocol+0x30/0x30
> [ 70.458695] [<c144dbb5>] ip_rcv+0x235/0x310
> [ 70.458695] [<c144d510>] ? inet_del_protocol+0x30/0x30
> [ 70.458695] [<c1412c36>] __netif_receive_skb+0x1d6/0x550
> [ 70.458695] [<c147c6a9>] ? inet_gro_receive+0x59/0x1f0
> [ 70.458695] [<c1413312>] netif_receive_skb+0x22/0x90
> [ 70.458695] [<c1413487>] napi_skb_finish+0x37/0x50
> [ 70.458695] [<c14139e3>] napi_gro_receive+0xe3/0xf0
> [ 70.458695] [<c12ff4c0>] ? xen_swiotlb_map_sg+0x20/0x20
> [ 70.458695] [<c12ff4d9>] ? xen_swiotlb_unmap_page+0x19/0x20
> [ 70.458695] [<f7983d6c>] skge_poll+0x34c/0x6f4 [skge]
> [ 70.458695] [<c141431a>] net_rx_action+0xfa/0x2a0
> [ 70.458695] [<c107cecf>] __do_softirq+0x9f/0x210
> [ 70.458695] [<c107ce30>] ? irq_exit+0xd0/0xd0
> [ 70.458695] <IRQ> [<c107ce15>] ? irq_exit+0xb5/0xd0
The skge driver uses hardware receive checksum where it computes the sum
of the packet (but does not check it). This kind of problem happens when some
part of the call chain above it updates the packet but does not update the checksum.
A fix like the following is presumably needed for some part of this path.
commit fa2da8cdae1dd64f78fc915ca1d1a4a93c71e7cb
Author: stephen hemminger <shemminger@vyatta.com>
Date: Tue Nov 15 08:09:14 2011 +0000
bridge: correct IPv6 checksum after pull
Bridge multicast snooping of ICMPv6 would incorrectly report a checksum prob
when used with Ethernet devices like sky2 that use CHECKSUM_COMPLETE.
When bytes are removed from skb, the computed checksum needs to be adjusted.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Martin Volf <martin.volf.42@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: Regression in skge that started around acb42a3 (so past v3.3-rc1)
2012-01-30 16:38 ` Stephen Hemminger
@ 2012-01-30 17:22 ` Eric Dumazet
2012-01-30 17:57 ` Konrad Rzeszutek Wilk
1 sibling, 0 replies; 9+ messages in thread
From: Eric Dumazet @ 2012-01-30 17:22 UTC (permalink / raw)
To: Stephen Hemminger; +Cc: Konrad Rzeszutek Wilk, netdev, davem, linux-kernel
Le lundi 30 janvier 2012 à 08:38 -0800, Stephen Hemminger a écrit :
> On Mon, 30 Jan 2012 10:58:16 -0500
> Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> wrote:
>
> > I hadn't done any git bisection yet, but with acb42a3 I started getting this:
> >
> > (and only on i686 - x86_64 does not show these):
> >
> > (This is with Xen, the other one is without)
> > [ 28.602121] eth2: no IPv6 routers present
> > [ 70.457712] eth2: hw csum failure.
> > [ 70.458695] Pid: 0, comm: swapper/0 Not tainted 3.3.0-rc1-00287-gacb42a3 #1
> > [ 70.
> > [ 70.458695] [<c140942b>] __skb_checksum_complete+0xb/0x10
> > [ 70.458695] [<c148e3b0>] nf_ip_checksum+0x60/0x120
> > [ 70.458695] [<c143ee6b>] udp_error+0xbb/0x1f0
> > [ 70.458695] [<c103c1e4>] ? check_events+0x8/0xc
> > [ 70.458695] [<c103c1db>] ? xen_restore_fl_direct_reloc+0x4/0x4
> > [ 70.458695] [<c11497ee>] ? put_cpu_partial+0x9e/0xb0
> > [ 70.458695] [<c143edb0>] ? udp_pkt_to_tuple+0x60/0x60
> > [ 70.458695] [<c143a2b6>] nf_conntrack_in+0xc6/0x5c0
> > [ 70.458695] [<c14751f8>] ? __udp4_lib_rcv+0x428/0x630
> > [ 70.458695] [<c1149dd0>] ? kfree+0xf0/0x120
> > [ 70.458695] [<c1405b60>] ? skb_release_data+0x90/0xb0
> > [ 70.458695] [<c1405b60>] ? skb_release_data+0x90/0xb0
> > [ 70.458695] [<c14057d8>] ? __kfree_skb+0x38/0x90
> > [ 70.458695] [<c144d510>] ? inet_del_protocol+0x30/0x30
> > [ 70.458695] [<c148f41e>] ipv4_conntrack_in+0x1e/0x30
> > [ 70.458695] [<c14360d3>] nf_iterate+0x63/0x90
> > [ 70.458695] [<c144d510>] ? inet_del_protocol+0x30/0x30
> > [ 70.458695] [<c1436292>] nf_hook_slow+0x62/0x140
> > [ 70.458695] [<c144d510>] ? inet_del_protocol+0x30/0x30
> > [ 70.458695] [<c144dbb5>] ip_rcv+0x235/0x310
> > [ 70.458695] [<c144d510>] ? inet_del_protocol+0x30/0x30
> > [ 70.458695] [<c1412c36>] __netif_receive_skb+0x1d6/0x550
> > [ 70.458695] [<c147c6a9>] ? inet_gro_receive+0x59/0x1f0
> > [ 70.458695] [<c1413312>] netif_receive_skb+0x22/0x90
> > [ 70.458695] [<c1413487>] napi_skb_finish+0x37/0x50
> > [ 70.458695] [<c14139e3>] napi_gro_receive+0xe3/0xf0
> > [ 70.458695] [<c12ff4c0>] ? xen_swiotlb_map_sg+0x20/0x20
> > [ 70.458695] [<c12ff4d9>] ? xen_swiotlb_unmap_page+0x19/0x20
> > [ 70.458695] [<f7983d6c>] skge_poll+0x34c/0x6f4 [skge]
> > [ 70.458695] [<c141431a>] net_rx_action+0xfa/0x2a0
> > [ 70.458695] [<c107cecf>] __do_softirq+0x9f/0x210
> > [ 70.458695] [<c107ce30>] ? irq_exit+0xd0/0xd0
> > [ 70.458695] <IRQ> [<c107ce15>] ? irq_exit+0xb5/0xd0
>
> The skge driver uses hardware receive checksum where it computes the sum
> of the packet (but does not check it). This kind of problem happens when some
> part of the call chain above it updates the packet but does not update the checksum.
> A fix like the following is presumably needed for some part of this path.
>
> commit fa2da8cdae1dd64f78fc915ca1d1a4a93c71e7cb
> Author: stephen hemminger <shemminger@vyatta.com>
> Date: Tue Nov 15 08:09:14 2011 +0000
>
> bridge: correct IPv6 checksum after pull
>
> Bridge multicast snooping of ICMPv6 would incorrectly report a checksum prob
> when used with Ethernet devices like sky2 that use CHECKSUM_COMPLETE.
> When bytes are removed from skb, the computed checksum needs to be adjusted.
>
> Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
> Tested-by: Martin Volf <martin.volf.42@gmail.com>
> Signed-off-by: David S. Miller <davem@davemloft.net>
>
>
> --
I wonder if we receive an skb with extra padding, and we lack a
pskb_trim_rcsum() in udp_error() (net/netfilter/nf_conntrack_proto_udp.c
)
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: Regression in skge that started around acb42a3 (so past v3.3-rc1)
2012-01-30 16:38 ` Stephen Hemminger
2012-01-30 17:22 ` Eric Dumazet
@ 2012-01-30 17:57 ` Konrad Rzeszutek Wilk
2012-01-30 18:02 ` David Miller
1 sibling, 1 reply; 9+ messages in thread
From: Konrad Rzeszutek Wilk @ 2012-01-30 17:57 UTC (permalink / raw)
To: Stephen Hemminger; +Cc: netdev, davem, linux-kernel
On Mon, Jan 30, 2012 at 08:38:43AM -0800, Stephen Hemminger wrote:
> On Mon, 30 Jan 2012 10:58:16 -0500
> Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> wrote:
>
> > I hadn't done any git bisection yet, but with acb42a3 I started getting this:
> >
> > (and only on i686 - x86_64 does not show these):
> >
> > (This is with Xen, the other one is without)
> > [ 28.602121] eth2: no IPv6 routers present
> > [ 70.457712] eth2: hw csum failure.
> > [ 70.458695] Pid: 0, comm: swapper/0 Not tainted 3.3.0-rc1-00287-gacb42a3 #1
> > [ 70.
> > [ 70.458695] [<c140942b>] __skb_checksum_complete+0xb/0x10
> > [ 70.458695] [<c148e3b0>] nf_ip_checksum+0x60/0x120
> > [ 70.458695] [<c143ee6b>] udp_error+0xbb/0x1f0
> > [ 70.458695] [<c103c1e4>] ? check_events+0x8/0xc
> > [ 70.458695] [<c103c1db>] ? xen_restore_fl_direct_reloc+0x4/0x4
> > [ 70.458695] [<c11497ee>] ? put_cpu_partial+0x9e/0xb0
> > [ 70.458695] [<c143edb0>] ? udp_pkt_to_tuple+0x60/0x60
> > [ 70.458695] [<c143a2b6>] nf_conntrack_in+0xc6/0x5c0
> > [ 70.458695] [<c14751f8>] ? __udp4_lib_rcv+0x428/0x630
> > [ 70.458695] [<c1149dd0>] ? kfree+0xf0/0x120
> > [ 70.458695] [<c1405b60>] ? skb_release_data+0x90/0xb0
> > [ 70.458695] [<c1405b60>] ? skb_release_data+0x90/0xb0
> > [ 70.458695] [<c14057d8>] ? __kfree_skb+0x38/0x90
> > [ 70.458695] [<c144d510>] ? inet_del_protocol+0x30/0x30
> > [ 70.458695] [<c148f41e>] ipv4_conntrack_in+0x1e/0x30
> > [ 70.458695] [<c14360d3>] nf_iterate+0x63/0x90
> > [ 70.458695] [<c144d510>] ? inet_del_protocol+0x30/0x30
> > [ 70.458695] [<c1436292>] nf_hook_slow+0x62/0x140
> > [ 70.458695] [<c144d510>] ? inet_del_protocol+0x30/0x30
> > [ 70.458695] [<c144dbb5>] ip_rcv+0x235/0x310
> > [ 70.458695] [<c144d510>] ? inet_del_protocol+0x30/0x30
> > [ 70.458695] [<c1412c36>] __netif_receive_skb+0x1d6/0x550
> > [ 70.458695] [<c147c6a9>] ? inet_gro_receive+0x59/0x1f0
> > [ 70.458695] [<c1413312>] netif_receive_skb+0x22/0x90
> > [ 70.458695] [<c1413487>] napi_skb_finish+0x37/0x50
> > [ 70.458695] [<c14139e3>] napi_gro_receive+0xe3/0xf0
> > [ 70.458695] [<c12ff4c0>] ? xen_swiotlb_map_sg+0x20/0x20
> > [ 70.458695] [<c12ff4d9>] ? xen_swiotlb_unmap_page+0x19/0x20
> > [ 70.458695] [<f7983d6c>] skge_poll+0x34c/0x6f4 [skge]
> > [ 70.458695] [<c141431a>] net_rx_action+0xfa/0x2a0
> > [ 70.458695] [<c107cecf>] __do_softirq+0x9f/0x210
> > [ 70.458695] [<c107ce30>] ? irq_exit+0xd0/0xd0
> > [ 70.458695] <IRQ> [<c107ce15>] ? irq_exit+0xb5/0xd0
>
> The skge driver uses hardware receive checksum where it computes the sum
> of the packet (but does not check it). This kind of problem happens when some
> part of the call chain above it updates the packet but does not update the checksum.
> A fix like the following is presumably needed for some part of this path.
Ah, so you are saying that the problem above is already fixed in 3.3-rc1.
OK, so what about the other one that I mentioned in the email:
[ 288.735236] IP: [<c127b1aa>] memcpy+0x1a/0x0a4f001 *pde = 0000000000000000
[ 288.735236] Oops: 0000 [#1] PREEMPT SMP
[ 288.751724] Modules linked in: dm_multipath dm_mod iscsi_boot_sysfs iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi libcrc32c crc32c sg sd_mod ata_generic sata_nv nouveau fbcon tileblit font bitblit e1000 softcursor ttm libata skge drm_kms_helper mxm_wmi video wmi scsi_mod [last unloaded: dump_dma]
[ 288.751724]
[ 288.751724] Pid: 0, comm: swapper/0 Tainted: G O 3.3.0-rc1-00383-g0a96265 #1 BIOSTAR Group N61PB-M2S/N61PB-M2S
[ 288.751724] EIP: 0060:[<c127b1aa>] EFLAGS: 00010217 CPU: 0
[ 288.751724] EIP is at memcpy+0x1a/0x40
[ 288.751724] EAX: f0a11040 EBX: 00000062 ECX: 00000018 EDX: 00000000
[ 288.751724] ESI: 00000000 EDI: f0a11040 EBP: f100bf2c ESP: f100bf20
[ 288.751724] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[ 288.751724] Process swapper/0 (pid: 0, ti=f100a000 task=c16b1020 task.ti=c16aa000)
[ 288.751724] Stack:
[ 288.751724] f1297c00 f1086144 f762dd80 f100bf88 f8449ccb 39e70110 00000043 39e70110
[ 288.751724] 00000043 00000000 c176b140 00000002 f100bf98 f0991d80 f1297c00 f11c4060
[ 288.751724] ffff0000 00000040 f1297c08 f1297800 00000000 00000000 00000062 f1297c08
[ 288.751724] Call Trace:
[ 288.751724] [<f8449ccb>] skge_poll+0x2ab/0x6f4 [skge]
[ 288.751724] [<c1413dba>] net_rx_action+0xfa/0x2a0
[ 288.751724] [<c107cecf>] __do_softirq+0x9f/0x210
[ 288.751724] [<c107ce30>] ? irq_exit+0xd0/0xd0
[ 288.751724] <IRQ>
[ 288.751724] [<c107ce15>] ? irq_exit+0xb5/0xd0
[ 288.751724] [<c1045e06>] ? do_IRQ+0x46/0xb0
[ 288.751724] [<c107cdc1>] ? irq_exit+0x61/0xd0
[ 288.751724] [<c105fb23>] ? smp_apic_timer_interrupt+0x53/0x90
[ 288.751724] [<c153abb0>] ? common_interrupt+0x30/0x38
[ 288.751724] [<c10685f5>] ? native_safe_halt+0x5/0x10
[ 288.751724] [<c104c53d>] ? default_idle+0xfd/0x200
[ 288.751724] [<c104c68c>] ? amd_e400_idle+0x4c/0x100
[ 288.751724] [<c1043fd8>] ? cpu_idle+0xa8/0xf0
[ 288.751724] [<c151602b>] ? rest_init+0x7b/0x80
[ 288.751724] [<c16f686d>] ? start_kernel+0x348/0x34e
[ 288.751724] [<c16f634f>] ? kernel_init+0x149/0x149
[ 288.751724] [<c16f60ba>] ? i386_start_kernel+0xa9/0xb0
[ 288.751724] Code: c6 43 4c 04 88 43 4d 8b 1c 24 89 ec 5d c3 90 90 90 55 89 e5 83 ec 0c 89 1c 24 89 cb 89 74 24 04 c1 e9 02 89 d6 89 7c 24 08 89 c7 <f3> a5 89 d9 83 e1 03 74 02 f3 a4 8b 1c 24 8b 74 24 04 8b 7c 24
[ 288.751724] EIP: [<c127b1aa>] memcpy+0x1a/0x40 SS:ESP 0068:f100bf20
[ 288.751724] CR2: 0000000000000000
[ 288.972094] ---[ end trace dca3e5f32515fe5d ]---
[ 288.976724] Kernel panic - not syncing: Fatal exception in interrupt
[ 288.983094] panic occurred, switching back to text console
>
> commit fa2da8cdae1dd64f78fc915ca1d1a4a93c71e7cb
> Author: stephen hemminger <shemminger@vyatta.com>
> Date: Tue Nov 15 08:09:14 2011 +0000
>
> bridge: correct IPv6 checksum after pull
>
> Bridge multicast snooping of ICMPv6 would incorrectly report a checksum prob
> when used with Ethernet devices like sky2 that use CHECKSUM_COMPLETE.
> When bytes are removed from skb, the computed checksum needs to be adjusted.
>
> Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
> Tested-by: Martin Volf <martin.volf.42@gmail.com>
> Signed-off-by: David S. Miller <davem@davemloft.net>
>
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: Regression in skge that started around acb42a3 (so past v3.3-rc1)
2012-01-30 17:57 ` Konrad Rzeszutek Wilk
@ 2012-01-30 18:02 ` David Miller
2012-01-30 18:22 ` Konrad Rzeszutek Wilk
0 siblings, 1 reply; 9+ messages in thread
From: David Miller @ 2012-01-30 18:02 UTC (permalink / raw)
To: konrad.wilk; +Cc: shemminger, netdev, linux-kernel
From: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Date: Mon, 30 Jan 2012 12:57:38 -0500
> Ah, so you are saying that the problem above is already fixed in 3.3-rc1.
No he's not saying that, he says somewhere we probably need a fix
"like" the commit he mentioned.
He did not say that commit fixes this bug.
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: Regression in skge that started around acb42a3 (so past v3.3-rc1)
2012-01-30 18:02 ` David Miller
@ 2012-01-30 18:22 ` Konrad Rzeszutek Wilk
2012-02-17 14:10 ` Konrad Rzeszutek Wilk
0 siblings, 1 reply; 9+ messages in thread
From: Konrad Rzeszutek Wilk @ 2012-01-30 18:22 UTC (permalink / raw)
To: David Miller; +Cc: shemminger, netdev, linux-kernel
On Mon, Jan 30, 2012 at 01:02:59PM -0500, David Miller wrote:
> From: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
> Date: Mon, 30 Jan 2012 12:57:38 -0500
>
> > Ah, so you are saying that the problem above is already fixed in 3.3-rc1.
>
> No he's not saying that, he says somewhere we probably need a fix
> "like" the commit he mentioned.
>
> He did not say that commit fixes this bug.
Ayee. Sounds you guys have an idea about this bug then. If you want me to run
a test-patch I can certainly do so. Thanks!
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: Regression in skge that started around acb42a3 (so past v3.3-rc1)
2012-01-30 18:22 ` Konrad Rzeszutek Wilk
@ 2012-02-17 14:10 ` Konrad Rzeszutek Wilk
2012-02-17 15:45 ` Stephen Hemminger
0 siblings, 1 reply; 9+ messages in thread
From: Konrad Rzeszutek Wilk @ 2012-02-17 14:10 UTC (permalink / raw)
To: David Miller; +Cc: shemminger, netdev, linux-kernel
On Mon, Jan 30, 2012 at 01:22:30PM -0500, Konrad Rzeszutek Wilk wrote:
> On Mon, Jan 30, 2012 at 01:02:59PM -0500, David Miller wrote:
> > From: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
> > Date: Mon, 30 Jan 2012 12:57:38 -0500
> >
> > > Ah, so you are saying that the problem above is already fixed in 3.3-rc1.
> >
> > No he's not saying that, he says somewhere we probably need a fix
> > "like" the commit he mentioned.
> >
> > He did not say that commit fixes this bug.
>
> Ayee. Sounds you guys have an idea about this bug then. If you want me to run
> a test-patch I can certainly do so. Thanks!
ping?
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: Regression in skge that started around acb42a3 (so past v3.3-rc1)
2012-02-17 14:10 ` Konrad Rzeszutek Wilk
@ 2012-02-17 15:45 ` Stephen Hemminger
2012-02-17 15:53 ` Stephen Hemminger
0 siblings, 1 reply; 9+ messages in thread
From: Stephen Hemminger @ 2012-02-17 15:45 UTC (permalink / raw)
To: Konrad Rzeszutek Wilk; +Cc: David Miller, netdev, linux-kernel
On Fri, 17 Feb 2012 09:10:05 -0500
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> wrote:
> On Mon, Jan 30, 2012 at 01:22:30PM -0500, Konrad Rzeszutek Wilk wrote:
> > On Mon, Jan 30, 2012 at 01:02:59PM -0500, David Miller wrote:
> > > From: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
> > > Date: Mon, 30 Jan 2012 12:57:38 -0500
> > >
> > > > Ah, so you are saying that the problem above is already fixed in 3.3-rc1.
> > >
> > > No he's not saying that, he says somewhere we probably need a fix
> > > "like" the commit he mentioned.
> > >
> > > He did not say that commit fixes this bug.
> >
> > Ayee. Sounds you guys have an idea about this bug then. If you want me to run
> > a test-patch I can certainly do so. Thanks!
>
> ping?
The change that caused this was reverted. It is propogating back to Linus's tree.
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: Regression in skge that started around acb42a3 (so past v3.3-rc1)
2012-02-17 15:45 ` Stephen Hemminger
@ 2012-02-17 15:53 ` Stephen Hemminger
0 siblings, 0 replies; 9+ messages in thread
From: Stephen Hemminger @ 2012-02-17 15:53 UTC (permalink / raw)
To: Stephen Hemminger
Cc: Konrad Rzeszutek Wilk, David Miller, netdev, linux-kernel
On Fri, 17 Feb 2012 07:45:11 -0800
Stephen Hemminger <shemminger@vyatta.com> wrote:
> On Fri, 17 Feb 2012 09:10:05 -0500
> Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> wrote:
>
> > On Mon, Jan 30, 2012 at 01:22:30PM -0500, Konrad Rzeszutek Wilk wrote:
> > > On Mon, Jan 30, 2012 at 01:02:59PM -0500, David Miller wrote:
> > > > From: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
> > > > Date: Mon, 30 Jan 2012 12:57:38 -0500
> > > >
> > > > > Ah, so you are saying that the problem above is already fixed in 3.3-rc1.
> > > >
> > > > No he's not saying that, he says somewhere we probably need a fix
> > > > "like" the commit he mentioned.
> > > >
> > > > He did not say that commit fixes this bug.
> > >
> > > Ayee. Sounds you guys have an idea about this bug then. If you want me to run
> > > a test-patch I can certainly do so. Thanks!
> >
Actually, I was confused, that was another skge change.
The checksum issue still exists and it is not a driver problem.
^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2012-02-17 15:53 UTC | newest]
Thread overview: 9+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2012-01-30 15:58 Regression in skge that started around acb42a3 (so past v3.3-rc1) Konrad Rzeszutek Wilk
2012-01-30 16:38 ` Stephen Hemminger
2012-01-30 17:22 ` Eric Dumazet
2012-01-30 17:57 ` Konrad Rzeszutek Wilk
2012-01-30 18:02 ` David Miller
2012-01-30 18:22 ` Konrad Rzeszutek Wilk
2012-02-17 14:10 ` Konrad Rzeszutek Wilk
2012-02-17 15:45 ` Stephen Hemminger
2012-02-17 15:53 ` Stephen Hemminger
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).