From: Shawn Guo <shawn.guo@linaro.org>
To: Rob Herring <robherring2@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org,
Grant Likely <grant.likely@secretlab.ca>,
Thomas Gleixner <tglx@linutronix.de>,
b-cousson@ti.com, Linus Walleij <linus.ml.walleij@gmail.com>
Subject: Re: [PATCH v4 4/4] gpio: pl061: enable interrupts with DT style binding
Date: Thu, 9 Feb 2012 15:58:05 -0800 [thread overview]
Message-ID: <20120209235805.GB3135@r65073-Latitude-D630> (raw)
In-Reply-To: <4F34429E.8070605@gmail.com>
On Thu, Feb 09, 2012 at 04:03:10PM -0600, Rob Herring wrote:
>
> On 02/09/2012 02:04 PM, Shawn Guo wrote:
> > On Fri, Feb 03, 2012 at 04:35:12PM -0600, Rob Herring wrote:
> > ...
> >> @@ -126,18 +127,16 @@ static void pl061_set_value(struct gpio_chip *gc, unsigned offset, int value)
> >> static int pl061_to_irq(struct gpio_chip *gc, unsigned offset)
> >> {
> >> struct pl061_gpio *chip = container_of(gc, struct pl061_gpio, gc);
> >> -
> >> - if (chip->irq_base <= 0)
> >> - return -EINVAL;
> >> -
> >> - return chip->irq_base + offset;
> >> + if (!chip->irq_gc)
> >> + return -ENXIO;
> >> + return irq_find_mapping(chip->irq_gc->domain, offset);
> >
> > If I understand the driver correctly, it will add a linear domain for
> > dt case. Do you have code somewhere creating the mapping before this
> > irq_find_mapping gets called here? The reason I'm asking this is I
> > have to call irq_create_mapping rather than irq_find_mapping here to
> > get imx gpio driver working with linear domain, otherwise the
> > irq_find_mapping call will fail.
> >
>
> Right, the user has to call irq_of_parse_and_map (which calls
> irq_create_mapping ultimately). Interrupts are allocated on demand. The
> dts needs to declare the gpio controller as an interrupt-controller and
> the node using the gpio line needs to set its interrupt parent and
> interrupt connection
>
Yes, that's how dt users use irq. But since I'm trying to make the
imx gpio irq_domain as linear for both non-dt and dt users. Calling
irq_create_mapping here may make sense for me, since it will not
require all these non-dt users change the way they use gpio irq.
Even for dt users, there may have some case that can not work in the
way we expect.
soc {
#address-cells = <1>;
#size-cells = <1>;
compatible = "simple-bus";
interrupt-parent = <&tzic>;
ranges;
esdhc@70008000 { /* ESDHC2 */
compatible = "fsl,imx51-esdhc";
reg = <0x70008000 0x4000>;
interrupts = <2>;
cd-gpios = <&gpio1 6 0>;
wp-gpios = <&gpio1 5 0>;
};
};
In above SD example, irq_of_parse_and_map will just work out the SD
controller internal irq to tzic. How can we work out the card-detection
irq to gpio controller in the same way?
--
Regards,
Shawn
next prev parent reply other threads:[~2012-02-09 23:58 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-02-03 22:35 [PATCH v4 0/4] generic irq chip domain support Rob Herring
2012-02-03 22:35 ` [PATCH v4 1/4] ARM: kconfig: always select IRQ_DOMAIN Rob Herring
2012-02-03 22:35 ` [PATCH v4 2/4] irq: add irq_domain support to generic-chip Rob Herring
2012-02-03 23:47 ` Grant Likely
2012-02-08 6:16 ` Shawn Guo
2012-02-04 14:08 ` Shawn Guo
2012-02-04 14:05 ` Grant Likely
2012-02-07 4:54 ` Rob Herring
2012-02-07 5:25 ` Grant Likely
2012-02-08 7:15 ` Shawn Guo
2012-02-08 16:49 ` Rob Herring
2012-02-03 22:35 ` [PATCH v4 3/4] ARM: imx: add irq domain support to tzic Rob Herring
2012-02-04 14:20 ` Shawn Guo
2012-02-03 22:35 ` [PATCH v4 4/4] gpio: pl061: enable interrupts with DT style binding Rob Herring
2012-02-09 20:04 ` Shawn Guo
2012-02-09 22:03 ` Rob Herring
2012-02-09 23:58 ` Shawn Guo [this message]
2012-02-10 0:17 ` Rob Herring
2012-02-10 16:37 ` Shawn Guo
2012-02-08 22:55 ` [PATCH v6] irq: add irq_domain support to generic-chip Rob Herring
2012-02-09 19:48 ` Shawn Guo
2012-02-09 22:31 ` Rob Herring
2012-02-09 23:36 ` Shawn Guo
2012-04-13 5:23 ` Thomas Abraham
2012-04-19 18:34 ` Grant Likely
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20120209235805.GB3135@r65073-Latitude-D630 \
--to=shawn.guo@linaro.org \
--cc=b-cousson@ti.com \
--cc=grant.likely@secretlab.ca \
--cc=linus.ml.walleij@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robherring2@gmail.com \
--cc=tglx@linutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).