[PATCH v7 0/7] omap: musb: Add device tree support

[PATCH v7 0/7] omap: musb: Add device tree support

[Kishon Vijay Abraham I]

This patch series adds device tree support for MUSB and device
tree support for all the related modules to get MUSB working in
OMAP platform.

A new omap-usb2 phy driver has been added (with only dt suppport)
to perform phy configurations. Previously this configuration was
performed by twl6030, using pdata function pointers.

With the addition of omap-usb2 to perform phy configurations,
twl6030 is made as a comparator driver to detect VBUS and ID events
and notify it to the glue layer.

musb core is _NOT_ yet converted to support device tree support as it
would need lot of driver re-design because of its enormous use of
function pointers. That will be in _TO DO_ list.

Changes from v6:
* Removed the dt data part of the patch series. It'll be sent as a
separate series.
* Replaced arch initcall in omap-usb2 phy driver with a module
platform driver. Dependent drivers should use -EPROBE_DEFER. 

Changes from v5:
minor cleanups like checking for return value in get_sync and few changes
in the documentation has been done.

Changes from v4:
duplicate getting of 'mode' property is removed in omap-musb glue.

Changes from v3:
remove the address in the node name of usb_otg_hs since the usb_otg_hs
node doesn't have a reg property. Thanks Ajay Gupta for finding this.

Changes from v2:
Fixed Sergei's comment to remove *0x* prefix in usb2phy@0x4a0ad080

Changes from v1:
* Fixed Rajendra Nayak comments (regulator naming, compatible naming of
musb and other minor cleanups.)
* It's agreed to have ocp2scp in drivers/bus and usb2 phy is a child of
ocp2scp, the documentation is updated accordingly.

Changes from RFC:
Removed the dependency on [RFC PATCH 00/11] OMAP System Control Module.
Writing to control module register is now handled in otg driver itself.
Once the system control module driver get upstreamed, I'll send a patch
to make use of API's in control module driver to write to control
module register.

This series was developed on
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb.git xceiv

This patch series depends on
[PATCH v3 0/2] omap: add ocp2scp as a bus driver

Performed MUSB device mode testing on OMAP4 panda, OMAP4 SDP
and OMAP3 beagle.

Kishon Vijay Abraham I (7):
  drivers: usb: phy: add a new driver for omap usb2 phy
  arm: omap: hwmod: add a new addr space in otg for writing to control
    module
  drivers: usb: otg: make twl6030_usb as a comparator driver to
    omap_usb2
  drivers: usb: twl6030: Add dt support for twl6030 usb
  drivers: usb: twl4030: Add device tree support for twl4030 usb
  drivers: usb: musb: Add device tree support for omap musb glue
  arm: omap: phy: remove unused functions from omap-phy-internal.c

 .../devicetree/bindings/bus/omap-ocp2scp.txt       |    3 +
 Documentation/devicetree/bindings/usb/omap-usb.txt |   49 ++++
 .../devicetree/bindings/usb/twlxxxx-usb.txt        |   40 +++
 arch/arm/mach-omap2/omap_hwmod_44xx_data.c         |    5 +
 arch/arm/mach-omap2/omap_phy_internal.c            |  138 ----------
 arch/arm/mach-omap2/twl-common.c                   |    5 -
 arch/arm/mach-omap2/usb-musb.c                     |    3 -
 drivers/usb/musb/omap2430.c                        |  106 +++++++-
 drivers/usb/musb/omap2430.h                        |    9 +
 drivers/usb/otg/twl4030-usb.c                      |   26 +-
 drivers/usb/otg/twl6030-usb.c                      |  157 ++++--------
 drivers/usb/phy/Kconfig                            |   10 +
 drivers/usb/phy/Makefile                           |    1 +
 drivers/usb/phy/omap-usb2.c                        |  271 ++++++++++++++++++++
 include/linux/usb/omap_usb.h                       |   46 ++++
 include/linux/usb/phy_companion.h                  |   34 +++
 16 files changed, 631 insertions(+), 272 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/usb/omap-usb.txt
 create mode 100644 Documentation/devicetree/bindings/usb/twlxxxx-usb.txt
 create mode 100644 drivers/usb/phy/omap-usb2.c
 create mode 100644 include/linux/usb/omap_usb.h
 create mode 100644 include/linux/usb/phy_companion.h

-- 
1.7.9.5

[PATCH v7 1/7] drivers: usb: phy: add a new driver for omap usb2 phy

[Kishon Vijay Abraham I]

All phy related programming like enabling/disabling the clocks, powering
on/off the phy is taken care of by this driver. It is also used for OTG
related functionality like srp.

This also includes device tree support for usb2 phy driver and
the documentation with device tree binding information is updated.

Currently writing to control module register is taken care in this
driver which will be removed once the control module driver is in place.

Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
 .../devicetree/bindings/bus/omap-ocp2scp.txt       |    3 +
 Documentation/devicetree/bindings/usb/omap-usb.txt |   17 ++
 drivers/usb/phy/Kconfig                            |   10 +
 drivers/usb/phy/Makefile                           |    1 +
 drivers/usb/phy/omap-usb2.c                        |  271 ++++++++++++++++++++
 include/linux/usb/omap_usb.h                       |   46 ++++
 include/linux/usb/phy_companion.h                  |   34 +++
 7 files changed, 382 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/usb/omap-usb.txt
 create mode 100644 drivers/usb/phy/omap-usb2.c
 create mode 100644 include/linux/usb/omap_usb.h
 create mode 100644 include/linux/usb/phy_companion.h

diff --git a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
index d2fe064..bb0c7f4 100644
--- a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
+++ b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
@@ -8,3 +8,6 @@ properties:
 
 Sub-nodes:
 All the devices connected to ocp2scp are described using sub-node to ocp2scp
+- usb2phy :
+   The binding details of usb2phy can be found in:
+   Documentation/devicetree/bindings/usb/omap-usb.txt
diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt
new file mode 100644
index 0000000..52f503b
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/omap-usb.txt
@@ -0,0 +1,17 @@
+OMAP USB PHY
+
+OMAP USB2 PHY
+
+Required properties:
+ - compatible: Should be "ti,omap-usb2"
+ - reg : Address and length of the register set for the device. Also
+add the address of control module dev conf register until a driver for
+control module is added
+
+This is usually a subnode of ocp2scp to which it is connected.
+
+usb2phy@4a0ad080 {
+	compatible = "ti,omap-usb2";
+	reg = <0x4a0ad080 0x58>,
+		<0x4a002300 0x1>;
+};
diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig
index e7cf84f..c2ab461 100644
--- a/drivers/usb/phy/Kconfig
+++ b/drivers/usb/phy/Kconfig
@@ -4,6 +4,16 @@
 comment "USB Physical Layer drivers"
 	depends on USB || USB_GADGET
 
+config OMAP_USB2
+	tristate "OMAP USB2 PHY Driver"
+	depends on OMAP_OCP2SCP
+	select USB_OTG_UTILS
+	help
+	  Enable this to support the transceiver that is part of SOC. This
+	  driver takes care of all the PHY functionality apart from comparator.
+	  The USB OTG controller communicates with the comparator using this
+	  driver.
+
 config USB_ISP1301
 	tristate "NXP ISP1301 USB transceiver support"
 	depends on USB || USB_GADGET
diff --git a/drivers/usb/phy/Makefile b/drivers/usb/phy/Makefile
index eca095b..d3fcec9 100644
--- a/drivers/usb/phy/Makefile
+++ b/drivers/usb/phy/Makefile
@@ -4,4 +4,5 @@
 
 ccflags-$(CONFIG_USB_DEBUG) := -DDEBUG
 
+obj-$(CONFIG_OMAP_USB2)			+= omap-usb2.o
 obj-$(CONFIG_USB_ISP1301)		+= isp1301.o
diff --git a/drivers/usb/phy/omap-usb2.c b/drivers/usb/phy/omap-usb2.c
new file mode 100644
index 0000000..984899b
--- /dev/null
+++ b/drivers/usb/phy/omap-usb2.c
@@ -0,0 +1,271 @@
+/*
+ * omap-usb2.c - USB PHY, talking to musb controller in OMAP.
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Author: Kishon Vijay Abraham I <kishon@ti.com>
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/of.h>
+#include <linux/io.h>
+#include <linux/usb/omap_usb.h>
+#include <linux/usb/phy_companion.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/pm_runtime.h>
+#include <linux/delay.h>
+
+/**
+ * omap_usb2_set_comparator - links the comparator present in the sytem with
+ *	this phy
+ * @comparator - the companion phy(comparator) for this phy
+ *
+ * The phy companion driver should call this API passing the phy_companion
+ * filled with set_vbus and start_srp to be used by usb phy.
+ *
+ * For use by phy companion driver
+ */
+int omap_usb2_set_comparator(struct phy_companion *comparator)
+{
+	struct omap_usb	*phy;
+	struct usb_phy	*x = usb_get_phy(USB_PHY_TYPE_USB2);
+
+	if (IS_ERR(x))
+		return -ENODEV;
+
+	phy = phy_to_omapusb(x);
+	phy->comparator = comparator;
+	return 0;
+}
+EXPORT_SYMBOL_GPL(omap_usb2_set_comparator);
+
+/**
+ * omap_usb_phy_power - power on/off the phy using control module reg
+ * @phy: struct omap_usb *
+ * @on: 0 or 1, based on powering on or off the PHY
+ *
+ * XXX: Remove this function once control module driver gets merged
+ */
+static void omap_usb_phy_power(struct omap_usb *phy, int on)
+{
+	u32 val;
+
+	if (on) {
+		val = readl(phy->control_dev);
+		if (val & PHY_PD) {
+			writel(~PHY_PD, phy->control_dev);
+			/* XXX: add proper documentation for this delay */
+			mdelay(200);
+		}
+	} else {
+		writel(PHY_PD, phy->control_dev);
+	}
+}
+
+static int omap_usb_set_vbus(struct usb_otg *otg, bool enabled)
+{
+	struct omap_usb *phy = phy_to_omapusb(otg->phy);
+
+	if (!phy->comparator)
+		return -ENODEV;
+
+	return phy->comparator->set_vbus(phy->comparator, enabled);
+}
+
+static int omap_usb_start_srp(struct usb_otg *otg)
+{
+	struct omap_usb *phy = phy_to_omapusb(otg->phy);
+
+	if (!phy->comparator)
+		return -ENODEV;
+
+	return phy->comparator->start_srp(phy->comparator);
+}
+
+static int omap_usb_set_host(struct usb_otg *otg, struct usb_bus *host)
+{
+	struct usb_phy	*phy = otg->phy;
+
+	otg->host = host;
+	if (!host)
+		phy->state = OTG_STATE_UNDEFINED;
+
+	return 0;
+}
+
+static int omap_usb_set_peripheral(struct usb_otg *otg,
+		struct usb_gadget *gadget)
+{
+	struct usb_phy	*phy = otg->phy;
+
+	otg->gadget = gadget;
+	if (!gadget)
+		phy->state = OTG_STATE_UNDEFINED;
+
+	return 0;
+}
+
+static int omap_usb2_suspend(struct usb_phy *x, int suspend)
+{
+	u32 ret;
+	struct omap_usb *phy = phy_to_omapusb(x);
+
+	if (suspend && !phy->is_suspended) {
+		omap_usb_phy_power(phy, 0);
+		pm_runtime_put_sync(phy->dev);
+		phy->is_suspended = 1;
+	} else if (!suspend && phy->is_suspended) {
+		ret = pm_runtime_get_sync(phy->dev);
+		if (ret < 0) {
+			dev_err(phy->dev, "get_sync failed with err %d\n",
+									ret);
+			return ret;
+		}
+		omap_usb_phy_power(phy, 1);
+		phy->is_suspended = 0;
+	}
+
+	return 0;
+}
+
+static int __devinit omap_usb2_probe(struct platform_device *pdev)
+{
+	struct omap_usb			*phy;
+	struct usb_otg			*otg;
+	struct resource			*res;
+
+	phy = devm_kzalloc(&pdev->dev, sizeof(*phy), GFP_KERNEL);
+	if (!phy) {
+		dev_err(&pdev->dev, "unable to allocate memory for USB2 PHY\n");
+		return -ENOMEM;
+	}
+
+	otg = devm_kzalloc(&pdev->dev, sizeof(*otg), GFP_KERNEL);
+	if (!otg) {
+		dev_err(&pdev->dev, "unable to allocate memory for USB OTG\n");
+		return -ENOMEM;
+	}
+
+	phy->dev		= &pdev->dev;
+
+	phy->phy.dev		= phy->dev;
+	phy->phy.label		= "omap-usb2";
+	phy->phy.set_suspend	= omap_usb2_suspend;
+	phy->phy.otg		= otg;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+
+	phy->control_dev = devm_request_and_ioremap(&pdev->dev, res);
+	if (phy->control_dev == NULL) {
+		dev_err(&pdev->dev, "Failed to obtain io memory\n");
+		return -ENXIO;
+	}
+
+	phy->is_suspended	= 1;
+	omap_usb_phy_power(phy, 0);
+
+	otg->set_host		= omap_usb_set_host;
+	otg->set_peripheral	= omap_usb_set_peripheral;
+	otg->set_vbus		= omap_usb_set_vbus;
+	otg->start_srp		= omap_usb_start_srp;
+	otg->phy		= &phy->phy;
+
+	phy->wkupclk = devm_clk_get(phy->dev, "usb_phy_cm_clk32k");
+	if (IS_ERR(phy->wkupclk)) {
+		dev_err(&pdev->dev, "unable to get usb_phy_cm_clk32k\n");
+		return PTR_ERR(phy->wkupclk);
+	}
+	clk_prepare(phy->wkupclk);
+
+	usb_add_phy(&phy->phy, USB_PHY_TYPE_USB2);
+
+	platform_set_drvdata(pdev, phy);
+
+	pm_runtime_enable(phy->dev);
+
+	return 0;
+}
+
+static int __devexit omap_usb2_remove(struct platform_device *pdev)
+{
+	struct omap_usb	*phy = platform_get_drvdata(pdev);
+
+	clk_unprepare(phy->wkupclk);
+	usb_remove_phy(&phy->phy);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM_RUNTIME
+
+static int omap_usb2_runtime_suspend(struct device *dev)
+{
+	struct platform_device	*pdev = to_platform_device(dev);
+	struct omap_usb	*phy = platform_get_drvdata(pdev);
+
+	clk_disable(phy->wkupclk);
+
+	return 0;
+}
+
+static int omap_usb2_runtime_resume(struct device *dev)
+{
+	u32 ret = 0;
+	struct platform_device	*pdev = to_platform_device(dev);
+	struct omap_usb	*phy = platform_get_drvdata(pdev);
+
+	ret = clk_enable(phy->wkupclk);
+	if (ret < 0)
+		dev_err(phy->dev, "Failed to enable wkupclk %d\n", ret);
+
+	return ret;
+}
+
+static const struct dev_pm_ops omap_usb2_pm_ops = {
+	SET_RUNTIME_PM_OPS(omap_usb2_runtime_suspend, omap_usb2_runtime_resume,
+		NULL)
+};
+
+#define DEV_PM_OPS     (&omap_usb2_pm_ops)
+#else
+#define DEV_PM_OPS     NULL
+#endif
+
+#ifdef CONFIG_OF
+static const struct of_device_id omap_usb2_id_table[] = {
+	{ .compatible = "ti,omap-usb2" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, omap_usb2_id_table);
+#endif
+
+static struct platform_driver omap_usb2_driver = {
+	.probe		= omap_usb2_probe,
+	.remove		= __devexit_p(omap_usb2_remove),
+	.driver		= {
+		.name	= "omap-usb2",
+		.owner	= THIS_MODULE,
+		.pm	= DEV_PM_OPS,
+		.of_match_table = of_match_ptr(omap_usb2_id_table),
+	},
+};
+
+module_platform_driver(omap_usb2_driver);
+
+MODULE_ALIAS("platform: omap_usb2");
+MODULE_AUTHOR("Texas Instruments Inc.");
+MODULE_DESCRIPTION("OMAP USB2 phy driver");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/usb/omap_usb.h b/include/linux/usb/omap_usb.h
new file mode 100644
index 0000000..0ea17f8
--- /dev/null
+++ b/include/linux/usb/omap_usb.h
@@ -0,0 +1,46 @@
+/*
+ * omap_usb.h -- omap usb2 phy header file
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Author: Kishon Vijay Abraham I <kishon@ti.com>
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef __DRIVERS_OMAP_USB2_H
+#define __DRIVERS_OMAP_USB2_H
+
+#include <linux/usb/otg.h>
+
+struct omap_usb {
+	struct usb_phy		phy;
+	struct phy_companion	*comparator;
+	struct device		*dev;
+	u32 __iomem		*control_dev;
+	struct clk		*wkupclk;
+	u8			is_suspended:1;
+};
+
+#define	PHY_PD	0x1
+
+#define	phy_to_omapusb(x)	container_of((x), struct omap_usb, phy)
+
+#if defined(CONFIG_OMAP_USB2) || defined(CONFIG_OMAP_USB2_MODULE)
+extern int omap_usb2_set_comparator(struct phy_companion *comparator);
+#else
+static inline int omap_usb2_set_comparator(struct phy_companion *comparator)
+{
+	return -ENODEV;
+}
+#endif
+
+#endif /* __DRIVERS_OMAP_USB_H */
diff --git a/include/linux/usb/phy_companion.h b/include/linux/usb/phy_companion.h
new file mode 100644
index 0000000..edd2ec2
--- /dev/null
+++ b/include/linux/usb/phy_companion.h
@@ -0,0 +1,34 @@
+/*
+ * phy-companion.h -- phy companion to indicate the comparator part of PHY
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Author: Kishon Vijay Abraham I <kishon@ti.com>
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef __DRIVERS_PHY_COMPANION_H
+#define __DRIVERS_PHY_COMPANION_H
+
+#include <linux/usb/otg.h>
+
+/* phy_companion to take care of VBUS, ID and srp capabilities */
+struct phy_companion {
+
+	/* effective for A-peripheral, ignored for B devices */
+	int	(*set_vbus)(struct phy_companion *x, bool enabled);
+
+	/* for B devices only:  start session with A-Host */
+	int	(*start_srp)(struct phy_companion *x);
+};
+
+#endif /* __DRIVERS_PHY_COMPANION_H */
-- 
1.7.9.5

[PATCH v7 2/7] arm: omap: hwmod: add a new addr space in otg for writing to control module

[Kishon Vijay Abraham I]

The mailbox register for usb otg in omap is present in control module.
On detection of any events VBUS or ID, this register should be written
to send the notification to musb core.

Till we have a separate control module driver to write to control module,
omap2430 will handle the register writes to control module by itself. So
a new address space to represent this control module register is added
to usb_otg_hs.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
 arch/arm/mach-omap2/omap_hwmod_44xx_data.c |    5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
index e8e5405..6334e22 100644
--- a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
@@ -5885,6 +5885,11 @@ static struct omap_hwmod_addr_space omap44xx_usb_otg_hs_addrs[] = {
 		.pa_end		= 0x4a0ab003,
 		.flags		= ADDR_TYPE_RT
 	},
+	{
+		.pa_start	= 0x4a00233c,
+		.pa_end		= 0x4a00233f,
+		.flags		= ADDR_TYPE_RT
+	},
 	{ }
 };
 
-- 
1.7.9.5

[PATCH v7 3/7] drivers: usb: otg: make twl6030_usb as a comparator driver to omap_usb2

[Kishon Vijay Abraham I]

All the PHY configuration other than VBUS, ID GND and OTG SRP are removed
from twl6030. The phy configurations are taken care by the dedicated
usb2 phy driver. So twl6030 is made as comparator driver for VBUS and
ID detection.

Writing to control module which is now handled in omap2430.c should be
removed once a driver for control module is in place.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
 drivers/usb/musb/omap2430.c   |   52 +++++++++++++++---
 drivers/usb/musb/omap2430.h   |    9 ++++
 drivers/usb/otg/twl6030-usb.c |  118 +++++++----------------------------------
 3 files changed, 72 insertions(+), 107 deletions(-)

diff --git a/drivers/usb/musb/omap2430.c b/drivers/usb/musb/omap2430.c
index 392fc7a..74dbd6f 100644
--- a/drivers/usb/musb/omap2430.c
+++ b/drivers/usb/musb/omap2430.c
@@ -44,6 +44,7 @@ struct omap2430_glue {
 	struct platform_device	*musb;
 	enum omap_musb_vbus_id_status status;
 	struct work_struct	omap_musb_mailbox_work;
+	u32 __iomem		*control_otghs;
 };
 #define glue_to_musb(g)		platform_get_drvdata(g->musb)
 
@@ -51,6 +52,26 @@ struct omap2430_glue		*_glue;
 
 static struct timer_list musb_idle_timer;
 
+/**
+ * omap4_usb_phy_mailbox - write to usb otg mailbox
+ * @glue: struct omap2430_glue *
+ * @val: the value to be written to the mailbox
+ *
+ * On detection of a device (ID pin is grounded), this API should be called
+ * to set AVALID, VBUSVALID and ID pin is grounded.
+ *
+ * When OMAP is connected to a host (OMAP in device mode), this API
+ * is called to set AVALID, VBUSVALID and ID pin in high impedance.
+ *
+ * XXX: This function will be removed once we have a seperate driver for
+ * control module
+ */
+static void omap4_usb_phy_mailbox(struct omap2430_glue *glue, u32 val)
+{
+	if (glue->control_otghs)
+		writel(val, glue->control_otghs);
+}
+
 static void musb_do_idle(unsigned long _musb)
 {
 	struct musb	*musb = (void *)_musb;
@@ -245,6 +266,7 @@ EXPORT_SYMBOL_GPL(omap_musb_mailbox);
 
 static void omap_musb_set_mailbox(struct omap2430_glue *glue)
 {
+	u32 val;
 	struct musb *musb = glue_to_musb(glue);
 	struct device *dev = musb->controller;
 	struct musb_hdrc_platform_data *pdata = dev->platform_data;
@@ -260,7 +282,8 @@ static void omap_musb_set_mailbox(struct omap2430_glue *glue)
 		musb->xceiv->last_event = USB_EVENT_ID;
 		if (!is_otg_enabled(musb) || musb->gadget_driver) {
 			pm_runtime_get_sync(dev);
-			usb_phy_init(musb->xceiv);
+			val = AVALID | VBUSVALID;
+			omap4_usb_phy_mailbox(glue, val);
 			omap2430_musb_set_vbus(musb, 1);
 		}
 		break;
@@ -273,7 +296,8 @@ static void omap_musb_set_mailbox(struct omap2430_glue *glue)
 		musb->xceiv->last_event = USB_EVENT_VBUS;
 		if (musb->gadget_driver)
 			pm_runtime_get_sync(dev);
-		usb_phy_init(musb->xceiv);
+		val = IDDIG | AVALID | VBUSVALID;
+		omap4_usb_phy_mailbox(glue, val);
 		break;
 
 	case OMAP_MUSB_ID_FLOAT:
@@ -291,7 +315,8 @@ static void omap_musb_set_mailbox(struct omap2430_glue *glue)
 			if (musb->xceiv->otg->set_vbus)
 				otg_set_vbus(musb->xceiv->otg, 0);
 		}
-		usb_phy_shutdown(musb->xceiv);
+		val = SESSEND | IDDIG;
+		omap4_usb_phy_mailbox(glue, val);
 		break;
 	default:
 		dev_dbg(dev, "ID float\n");
@@ -366,6 +391,7 @@ err1:
 static void omap2430_musb_enable(struct musb *musb)
 {
 	u8		devctl;
+	u32		val;
 	unsigned long timeout = jiffies + msecs_to_jiffies(1000);
 	struct device *dev = musb->controller;
 	struct omap2430_glue *glue = dev_get_drvdata(dev->parent);
@@ -375,7 +401,8 @@ static void omap2430_musb_enable(struct musb *musb)
 	switch (glue->status) {
 
 	case OMAP_MUSB_ID_GROUND:
-		usb_phy_init(musb->xceiv);
+		val = AVALID | VBUSVALID;
+		omap4_usb_phy_mailbox(glue, val);
 		if (data->interface_type != MUSB_INTERFACE_UTMI)
 			break;
 		devctl = musb_readb(musb->mregs, MUSB_DEVCTL);
@@ -394,7 +421,8 @@ static void omap2430_musb_enable(struct musb *musb)
 		break;
 
 	case OMAP_MUSB_VBUS_VALID:
-		usb_phy_init(musb->xceiv);
+		val = IDDIG | AVALID | VBUSVALID;
+		omap4_usb_phy_mailbox(glue, val);
 		break;
 
 	default:
@@ -404,11 +432,14 @@ static void omap2430_musb_enable(struct musb *musb)
 
 static void omap2430_musb_disable(struct musb *musb)
 {
+	u32 val;
 	struct device *dev = musb->controller;
 	struct omap2430_glue *glue = dev_get_drvdata(dev->parent);
 
-	if (glue->status != OMAP_MUSB_UNKNOWN)
-		usb_phy_shutdown(musb->xceiv);
+	if (glue->status != OMAP_MUSB_UNKNOWN) {
+		val = SESSEND | IDDIG;
+		omap4_usb_phy_mailbox(glue, val);
+	}
 }
 
 static int omap2430_musb_exit(struct musb *musb)
@@ -440,6 +471,7 @@ static int __devinit omap2430_probe(struct platform_device *pdev)
 	struct musb_hdrc_platform_data	*pdata = pdev->dev.platform_data;
 	struct platform_device		*musb;
 	struct omap2430_glue		*glue;
+	struct resource			*res;
 	int				ret = -ENOMEM;
 
 	glue = devm_kzalloc(&pdev->dev, sizeof(*glue), GFP_KERNEL);
@@ -462,6 +494,12 @@ static int __devinit omap2430_probe(struct platform_device *pdev)
 	glue->musb			= musb;
 	glue->status			= OMAP_MUSB_UNKNOWN;
 
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+
+	glue->control_otghs = devm_request_and_ioremap(&pdev->dev, res);
+	if (glue->control_otghs == NULL)
+		dev_dbg(&pdev->dev, "Failed to obtain control memory\n");
+
 	pdata->platform_ops		= &omap2430_ops;
 
 	platform_set_drvdata(pdev, glue);
diff --git a/drivers/usb/musb/omap2430.h b/drivers/usb/musb/omap2430.h
index 40b3c02..b85f397 100644
--- a/drivers/usb/musb/omap2430.h
+++ b/drivers/usb/musb/omap2430.h
@@ -49,4 +49,13 @@
 #define OTG_FORCESTDBY		0x414
 #	define	ENABLEFORCE		(1 << 0)
 
+/*
+ * Control Module bit definitions
+ * XXX: Will be removed once we have a driver for control module.
+ */
+#define	AVALID				BIT(0)
+#define	BVALID				BIT(1)
+#define	VBUSVALID			BIT(2)
+#define	SESSEND				BIT(3)
+#define	IDDIG				BIT(4)
 #endif	/* __MUSB_OMAP243X_H__ */
diff --git a/drivers/usb/otg/twl6030-usb.c b/drivers/usb/otg/twl6030-usb.c
index 6907d8d..32525bb 100644
--- a/drivers/usb/otg/twl6030-usb.c
+++ b/drivers/usb/otg/twl6030-usb.c
@@ -25,8 +25,9 @@
 #include <linux/interrupt.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
-#include <linux/usb/otg.h>
 #include <linux/usb/musb-omap.h>
+#include <linux/usb/phy_companion.h>
+#include <linux/usb/omap_usb.h>
 #include <linux/i2c/twl.h>
 #include <linux/regulator/consumer.h>
 #include <linux/err.h>
@@ -87,7 +88,7 @@
 #define	VBUS_DET			BIT(2)
 
 struct twl6030_usb {
-	struct usb_phy		phy;
+	struct phy_companion	comparator;
 	struct device		*dev;
 
 	/* for vbus reporting with irqs disabled */
@@ -107,7 +108,7 @@ struct twl6030_usb {
 	unsigned long		features;
 };
 
-#define phy_to_twl(x)		container_of((x), struct twl6030_usb, phy)
+#define	comparator_to_twl(x) container_of((x), struct twl6030_usb, comparator)
 
 /*-------------------------------------------------------------------------*/
 
@@ -137,50 +138,9 @@ static inline u8 twl6030_readb(struct twl6030_usb *twl, u8 module, u8 address)
 	return ret;
 }
 
-static int twl6030_phy_init(struct usb_phy *x)
+static int twl6030_start_srp(struct phy_companion *comparator)
 {
-	struct twl6030_usb *twl;
-	struct device *dev;
-	struct twl4030_usb_data *pdata;
-
-	twl = phy_to_twl(x);
-	dev  = twl->dev;
-	pdata = dev->platform_data;
-
-	if (twl->linkstat == OMAP_MUSB_ID_GROUND)
-		pdata->phy_power(twl->dev, 1, 1);
-	else
-		pdata->phy_power(twl->dev, 0, 1);
-
-	return 0;
-}
-
-static void twl6030_phy_shutdown(struct usb_phy *x)
-{
-	struct twl6030_usb *twl;
-	struct device *dev;
-	struct twl4030_usb_data *pdata;
-
-	twl = phy_to_twl(x);
-	dev  = twl->dev;
-	pdata = dev->platform_data;
-	pdata->phy_power(twl->dev, 0, 0);
-}
-
-static int twl6030_phy_suspend(struct usb_phy *x, int suspend)
-{
-	struct twl6030_usb *twl = phy_to_twl(x);
-	struct device *dev = twl->dev;
-	struct twl4030_usb_data *pdata = dev->platform_data;
-
-	pdata->phy_suspend(dev, suspend);
-
-	return 0;
-}
-
-static int twl6030_start_srp(struct usb_otg *otg)
-{
-	struct twl6030_usb *twl = phy_to_twl(otg->phy);
+	struct twl6030_usb *twl = comparator_to_twl(comparator);
 
 	twl6030_writeb(twl, TWL_MODULE_USB, 0x24, USB_VBUS_CTRL_SET);
 	twl6030_writeb(twl, TWL_MODULE_USB, 0x84, USB_VBUS_CTRL_SET);
@@ -313,23 +273,8 @@ static irqreturn_t twl6030_usbotg_irq(int irq, void *_twl)
 	return IRQ_HANDLED;
 }
 
-static int twl6030_set_peripheral(struct usb_otg *otg,
-		struct usb_gadget *gadget)
+static int twl6030_enable_irq(struct twl6030_usb *twl)
 {
-	if (!otg)
-		return -ENODEV;
-
-	otg->gadget = gadget;
-	if (!gadget)
-		otg->phy->state = OTG_STATE_UNDEFINED;
-
-	return 0;
-}
-
-static int twl6030_enable_irq(struct usb_phy *x)
-{
-	struct twl6030_usb *twl = phy_to_twl(x);
-
 	twl6030_writeb(twl, TWL_MODULE_USB, 0x1, USB_ID_INT_EN_HI_SET);
 	twl6030_interrupt_unmask(0x05, REG_INT_MSK_LINE_C);
 	twl6030_interrupt_unmask(0x05, REG_INT_MSK_STS_C);
@@ -362,9 +307,9 @@ static void otg_set_vbus_work(struct work_struct *data)
 							CHARGERUSB_CTRL1);
 }
 
-static int twl6030_set_vbus(struct usb_otg *otg, bool enabled)
+static int twl6030_set_vbus(struct phy_companion *comparator, bool enabled)
 {
-	struct twl6030_usb *twl = phy_to_twl(otg->phy);
+	struct twl6030_usb *twl = comparator_to_twl(comparator);
 
 	twl->vbus_enable = enabled;
 	schedule_work(&twl->set_vbus_work);
@@ -372,23 +317,12 @@ static int twl6030_set_vbus(struct usb_otg *otg, bool enabled)
 	return 0;
 }
 
-static int twl6030_set_host(struct usb_otg *otg, struct usb_bus *host)
-{
-	if (!otg)
-		return -ENODEV;
-
-	otg->host = host;
-	if (!host)
-		otg->phy->state = OTG_STATE_UNDEFINED;
-	return 0;
-}
-
 static int __devinit twl6030_usb_probe(struct platform_device *pdev)
 {
+	u32 ret;
 	struct twl6030_usb	*twl;
 	int			status, err;
 	struct twl4030_usb_data *pdata;
-	struct usb_otg		*otg;
 	struct device *dev = &pdev->dev;
 	pdata = dev->platform_data;
 
@@ -396,28 +330,20 @@ static int __devinit twl6030_usb_probe(struct platform_device *pdev)
 	if (!twl)
 		return -ENOMEM;
 
-	otg = devm_kzalloc(dev, sizeof *otg, GFP_KERNEL);
-	if (!otg)
-		return -ENOMEM;
-
 	twl->dev		= &pdev->dev;
 	twl->irq1		= platform_get_irq(pdev, 0);
 	twl->irq2		= platform_get_irq(pdev, 1);
 	twl->features		= pdata->features;
 	twl->linkstat		= OMAP_MUSB_UNKNOWN;
 
-	twl->phy.dev		= twl->dev;
-	twl->phy.label		= "twl6030";
-	twl->phy.otg		= otg;
-	twl->phy.init		= twl6030_phy_init;
-	twl->phy.shutdown	= twl6030_phy_shutdown;
-	twl->phy.set_suspend	= twl6030_phy_suspend;
+	twl->comparator.set_vbus	= twl6030_set_vbus;
+	twl->comparator.start_srp	= twl6030_start_srp;
 
-	otg->phy		= &twl->phy;
-	otg->set_host		= twl6030_set_host;
-	otg->set_peripheral	= twl6030_set_peripheral;
-	otg->set_vbus		= twl6030_set_vbus;
-	otg->start_srp		= twl6030_start_srp;
+	ret = omap_usb2_set_comparator(&twl->comparator);
+	if (ret == -ENODEV) {
+		dev_info(&pdev->dev, "phy not ready, deferring probe");
+		return -EPROBE_DEFER;
+	}
 
 	/* init spinlock for workqueue */
 	spin_lock_init(&twl->lock);
@@ -427,7 +353,6 @@ static int __devinit twl6030_usb_probe(struct platform_device *pdev)
 		dev_err(&pdev->dev, "ldo init failed\n");
 		return err;
 	}
-	usb_add_phy(&twl->phy, USB_PHY_TYPE_USB2);
 
 	platform_set_drvdata(pdev, twl);
 	if (device_create_file(&pdev->dev, &dev_attr_vbus))
@@ -458,9 +383,7 @@ static int __devinit twl6030_usb_probe(struct platform_device *pdev)
 	}
 
 	twl->asleep = 0;
-	pdata->phy_init(dev);
-	twl6030_phy_suspend(&twl->phy, 0);
-	twl6030_enable_irq(&twl->phy);
+	twl6030_enable_irq(twl);
 	dev_info(&pdev->dev, "Initialized TWL6030 USB module\n");
 
 	return 0;
@@ -470,10 +393,6 @@ static int __exit twl6030_usb_remove(struct platform_device *pdev)
 {
 	struct twl6030_usb *twl = platform_get_drvdata(pdev);
 
-	struct twl4030_usb_data *pdata;
-	struct device *dev = &pdev->dev;
-	pdata = dev->platform_data;
-
 	twl6030_interrupt_mask(TWL6030_USBOTG_INT_MASK,
 		REG_INT_MSK_LINE_C);
 	twl6030_interrupt_mask(TWL6030_USBOTG_INT_MASK,
@@ -481,7 +400,6 @@ static int __exit twl6030_usb_remove(struct platform_device *pdev)
 	free_irq(twl->irq1, twl);
 	free_irq(twl->irq2, twl);
 	regulator_put(twl->usb3v3);
-	pdata->phy_exit(twl->dev);
 	device_remove_file(twl->dev, &dev_attr_vbus);
 	cancel_work_sync(&twl->set_vbus_work);
 
-- 
1.7.9.5

[PATCH v7 4/7] drivers: usb: twl6030: Add dt support for twl6030 usb

[Kishon Vijay Abraham I]

Add device tree support for twl6030 usb driver.
Update the Documentation with device tree binding information.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
 .../devicetree/bindings/usb/twlxxxx-usb.txt        |   21 +++++++++++
 drivers/usb/otg/twl6030-usb.c                      |   39 +++++++++++++-------
 2 files changed, 47 insertions(+), 13 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/usb/twlxxxx-usb.txt

diff --git a/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt
new file mode 100644
index 0000000..930f9ff
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt
@@ -0,0 +1,21 @@
+USB COMPARATOR OF TWL CHIPS
+
+TWL6030 USB COMPARATOR
+ - compatible : Should be "ti,twl6030-usb"
+ - interrupts : Two interrupt numbers to the cpu should be specified. First
+   interrupt number is the otg interrupt number that raises ID interrupts when
+   the controller has to act as host and the second interrupt number is the
+   usb interrupt number that raises VBUS interrupts when the controller has to
+   act as device
+ - usb-supply : phandle to the regulator device tree node. It should be vusb
+   if it is twl6030 or ldousb if it is twl6025 subclass.
+
+twl6030-usb {
+	compatible = "ti,twl6030-usb";
+	interrupts = < 4 10 >;
+};
+
+Board specific device node entry
+&twl6030-usb {
+	usb-supply = <&vusb>;
+};
diff --git a/drivers/usb/otg/twl6030-usb.c b/drivers/usb/otg/twl6030-usb.c
index 32525bb..fcadef7 100644
--- a/drivers/usb/otg/twl6030-usb.c
+++ b/drivers/usb/otg/twl6030-usb.c
@@ -105,7 +105,7 @@ struct twl6030_usb {
 	u8			asleep;
 	bool			irq_enabled;
 	bool			vbus_enable;
-	unsigned long		features;
+	const char		*regulator;
 };
 
 #define	comparator_to_twl(x) container_of((x), struct twl6030_usb, comparator)
@@ -153,13 +153,6 @@ static int twl6030_start_srp(struct phy_companion *comparator)
 
 static int twl6030_usb_ldo_init(struct twl6030_usb *twl)
 {
-	char *regulator_name;
-
-	if (twl->features & TWL6025_SUBCLASS)
-		regulator_name = "ldousb";
-	else
-		regulator_name = "vusb";
-
 	/* Set to OTG_REV 1.3 and turn on the ID_WAKEUP_COMP */
 	twl6030_writeb(twl, TWL6030_MODULE_ID0 , 0x1, TWL6030_BACKUP_REG);
 
@@ -169,7 +162,7 @@ static int twl6030_usb_ldo_init(struct twl6030_usb *twl)
 	/* Program MISC2 register and set bit VUSB_IN_VBAT */
 	twl6030_writeb(twl, TWL6030_MODULE_ID0 , 0x10, TWL6030_MISC2);
 
-	twl->usb3v3 = regulator_get(twl->dev, regulator_name);
+	twl->usb3v3 = regulator_get(twl->dev, twl->regulator);
 	if (IS_ERR(twl->usb3v3))
 		return -ENODEV;
 
@@ -322,9 +315,9 @@ static int __devinit twl6030_usb_probe(struct platform_device *pdev)
 	u32 ret;
 	struct twl6030_usb	*twl;
 	int			status, err;
-	struct twl4030_usb_data *pdata;
-	struct device *dev = &pdev->dev;
-	pdata = dev->platform_data;
+	struct device_node	*np = pdev->dev.of_node;
+	struct device		*dev = &pdev->dev;
+	struct twl4030_usb_data	*pdata = dev->platform_data;
 
 	twl = devm_kzalloc(dev, sizeof *twl, GFP_KERNEL);
 	if (!twl)
@@ -333,7 +326,6 @@ static int __devinit twl6030_usb_probe(struct platform_device *pdev)
 	twl->dev		= &pdev->dev;
 	twl->irq1		= platform_get_irq(pdev, 0);
 	twl->irq2		= platform_get_irq(pdev, 1);
-	twl->features		= pdata->features;
 	twl->linkstat		= OMAP_MUSB_UNKNOWN;
 
 	twl->comparator.set_vbus	= twl6030_set_vbus;
@@ -345,6 +337,18 @@ static int __devinit twl6030_usb_probe(struct platform_device *pdev)
 		return -EPROBE_DEFER;
 	}
 
+	if (np) {
+		twl->regulator = "usb";
+	} else if (pdata) {
+		if (pdata->features & TWL6025_SUBCLASS)
+			twl->regulator = "ldousb";
+		else
+			twl->regulator = "vusb";
+	} else {
+		dev_err(&pdev->dev, "twl6030 initialized without pdata\n");
+		return -EINVAL;
+	}
+
 	/* init spinlock for workqueue */
 	spin_lock_init(&twl->lock);
 
@@ -406,12 +410,21 @@ static int __exit twl6030_usb_remove(struct platform_device *pdev)
 	return 0;
 }
 
+#ifdef CONFIG_OF
+static const struct of_device_id twl6030_usb_id_table[] = {
+	{ .compatible = "ti,twl6030-usb" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, twl6030_usb_id_table);
+#endif
+
 static struct platform_driver twl6030_usb_driver = {
 	.probe		= twl6030_usb_probe,
 	.remove		= __exit_p(twl6030_usb_remove),
 	.driver		= {
 		.name	= "twl6030_usb",
 		.owner	= THIS_MODULE,
+		.of_match_table = of_match_ptr(twl6030_usb_id_table),
 	},
 };
 
-- 
1.7.9.5

[PATCH v7 5/7] drivers: usb: twl4030: Add device tree support for twl4030 usb

[Kishon Vijay Abraham I]

Add device tree support for twl4030 usb driver.
Update the Documentation with device tree binding information.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
 .../devicetree/bindings/usb/twlxxxx-usb.txt        |   19 ++++++++++++++
 drivers/usb/otg/twl4030-usb.c                      |   26 +++++++++++++++-----
 2 files changed, 39 insertions(+), 6 deletions(-)

diff --git a/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt
index 930f9ff..36b9aed 100644
--- a/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt
+++ b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt
@@ -19,3 +19,22 @@ Board specific device node entry
 &twl6030-usb {
 	usb-supply = <&vusb>;
 };
+
+TWL4030 USB PHY AND COMPARATOR
+ - compatible : Should be "ti,twl4030-usb"
+ - interrupts : The interrupt numbers to the cpu should be specified. First
+   interrupt number is the otg interrupt number that raises ID interrupts
+   and VBUS interrupts. The second interrupt number is optional.
+ - <supply-name>-supply : phandle to the regulator device tree node.
+   <supply-name> should be vusb1v5, vusb1v8 and vusb3v1
+ - usb_mode : The mode used by the phy to connect to the controller. "1"
+   specifies "ULPI" mode and "2" specifies "CEA2011_3PIN" mode.
+
+twl4030-usb {
+	compatible = "ti,twl4030-usb";
+	interrupts = < 10 4 >;
+	usb1v5-supply = <&vusb1v5>;
+	usb1v8-supply = <&vusb1v8>;
+	usb3v1-supply = <&vusb3v1>;
+	usb_mode = <1>;
+};
diff --git a/drivers/usb/otg/twl4030-usb.c b/drivers/usb/otg/twl4030-usb.c
index 523cad5..f0d2e75 100644
--- a/drivers/usb/otg/twl4030-usb.c
+++ b/drivers/usb/otg/twl4030-usb.c
@@ -585,23 +585,28 @@ static int __devinit twl4030_usb_probe(struct platform_device *pdev)
 	struct twl4030_usb	*twl;
 	int			status, err;
 	struct usb_otg		*otg;
-
-	if (!pdata) {
-		dev_dbg(&pdev->dev, "platform_data not available\n");
-		return -EINVAL;
-	}
+	struct device_node	*np = pdev->dev.of_node;
 
 	twl = devm_kzalloc(&pdev->dev, sizeof *twl, GFP_KERNEL);
 	if (!twl)
 		return -ENOMEM;
 
+	if (np)
+		of_property_read_u32(np, "usb_mode",
+				(enum twl4030_usb_mode *)&twl->usb_mode);
+	else if (pdata)
+		twl->usb_mode = pdata->usb_mode;
+	else {
+		dev_err(&pdev->dev, "twl4030 initialized without pdata\n");
+		return -EINVAL;
+	}
+
 	otg = devm_kzalloc(&pdev->dev, sizeof *otg, GFP_KERNEL);
 	if (!otg)
 		return -ENOMEM;
 
 	twl->dev		= &pdev->dev;
 	twl->irq		= platform_get_irq(pdev, 0);
-	twl->usb_mode		= pdata->usb_mode;
 	twl->vbus_supplied	= false;
 	twl->asleep		= 1;
 	twl->linkstat		= OMAP_MUSB_UNKNOWN;
@@ -690,12 +695,21 @@ static int __exit twl4030_usb_remove(struct platform_device *pdev)
 	return 0;
 }
 
+#ifdef CONFIG_OF
+static const struct of_device_id twl4030_usb_id_table[] = {
+	{ .compatible = "ti,twl4030-usb" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, twl4030_usb_id_table);
+#endif
+
 static struct platform_driver twl4030_usb_driver = {
 	.probe		= twl4030_usb_probe,
 	.remove		= __exit_p(twl4030_usb_remove),
 	.driver		= {
 		.name	= "twl4030_usb",
 		.owner	= THIS_MODULE,
+		.of_match_table = of_match_ptr(twl4030_usb_id_table),
 	},
 };
 
-- 
1.7.9.5

[PATCH v7 6/7] drivers: usb: musb: Add device tree support for omap musb glue

[Kishon Vijay Abraham I]

Added device tree support for omap musb driver and updated the
Documentation with device tree binding information.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
 Documentation/devicetree/bindings/usb/omap-usb.txt |   34 +++++++++++-
 drivers/usb/musb/omap2430.c                        |   54 ++++++++++++++++++++
 2 files changed, 87 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt
index 52f503b..49a90fb 100644
--- a/Documentation/devicetree/bindings/usb/omap-usb.txt
+++ b/Documentation/devicetree/bindings/usb/omap-usb.txt
@@ -1,4 +1,4 @@
-OMAP USB PHY
+OMAP USB PHY AND GLUE
 
 OMAP USB2 PHY
 
@@ -15,3 +15,35 @@ usb2phy@4a0ad080 {
 	reg = <0x4a0ad080 0x58>,
 		<0x4a002300 0x1>;
 };
+
+OMAP MUSB GLUE
+ - compatible : Should be "ti,musb-omap2430"
+ - ti,hwmods : must be "usb_otg_hs"
+ - multipoint : Should be "1" indicating the musb controller supports
+   multipoint. This is a MUSB configuration-specific setting.
+ - num_eps : Specifies the number of endpoints. This is also a
+   MUSB configuration-specific setting. Should be set to "16"
+ - ram_bits : Specifies the ram address size. Should be set to "12"
+ - interface_type : This is a board specific setting to describe the type of
+   interface between the controller and the phy. It should be "0" or "1"
+   specifying ULPI and UTMI respectively.
+ - mode : Should be "3" to represent OTG. "1" signifies HOST and "2"
+   represents PERIPHERAL.
+ - power : Should be "50". This signifies the controller can supply upto
+   100mA when operating in host mode.
+
+SOC specific device node entry
+usb_otg_hs: usb_otg_hs@4a0ab000 {
+	compatible = "ti,musb-omap2430";
+	ti,hwmods = "usb_otg_hs";
+	multipoint = <1>;
+	num_eps = <16>;
+	ram_bits = <12>;
+};
+
+Board specific device node entry
+&usb_otg_hs {
+	interface_type = <1>;
+	mode = <3>;
+	power = <50>;
+};
diff --git a/drivers/usb/musb/omap2430.c b/drivers/usb/musb/omap2430.c
index 74dbd6f..8b1d7c0 100644
--- a/drivers/usb/musb/omap2430.c
+++ b/drivers/usb/musb/omap2430.c
@@ -30,6 +30,7 @@
 #include <linux/init.h>
 #include <linux/list.h>
 #include <linux/io.h>
+#include <linux/of.h>
 #include <linux/platform_device.h>
 #include <linux/dma-mapping.h>
 #include <linux/pm_runtime.h>
@@ -469,8 +470,11 @@ static u64 omap2430_dmamask = DMA_BIT_MASK(32);
 static int __devinit omap2430_probe(struct platform_device *pdev)
 {
 	struct musb_hdrc_platform_data	*pdata = pdev->dev.platform_data;
+	struct omap_musb_board_data	*data;
 	struct platform_device		*musb;
 	struct omap2430_glue		*glue;
+	struct device_node		*np = pdev->dev.of_node;
+	struct musb_hdrc_config		*config;
 	struct resource			*res;
 	int				ret = -ENOMEM;
 
@@ -500,6 +504,42 @@ static int __devinit omap2430_probe(struct platform_device *pdev)
 	if (glue->control_otghs == NULL)
 		dev_dbg(&pdev->dev, "Failed to obtain control memory\n");
 
+	if (np) {
+		pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
+		if (!pdata) {
+			dev_err(&pdev->dev,
+				"failed to allocate musb platfrom data\n");
+			ret = -ENOMEM;
+			goto err1;
+		}
+
+		data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+		if (!data) {
+			dev_err(&pdev->dev,
+					"failed to allocate musb board data\n");
+			ret = -ENOMEM;
+			goto err1;
+		}
+
+		config = devm_kzalloc(&pdev->dev, sizeof(*config), GFP_KERNEL);
+		if (!data) {
+			dev_err(&pdev->dev,
+				"failed to allocate musb hdrc config\n");
+			goto err1;
+		}
+
+		of_property_read_u32(np, "mode", (u32 *)&pdata->mode);
+		of_property_read_u32(np, "interface_type",
+						(u32 *)&data->interface_type);
+		of_property_read_u32(np, "num_eps", (u32 *)&config->num_eps);
+		of_property_read_u32(np, "ram_bits", (u32 *)&config->ram_bits);
+		of_property_read_u32(np, "power", (u32 *)&pdata->power);
+		config->multipoint = of_property_read_bool(np, "multipoint");
+
+		pdata->board_data	= data;
+		pdata->config		= config;
+	}
+
 	pdata->platform_ops		= &omap2430_ops;
 
 	platform_set_drvdata(pdev, glue);
@@ -596,12 +636,26 @@ static struct dev_pm_ops omap2430_pm_ops = {
 #define DEV_PM_OPS	NULL
 #endif
 
+#ifdef CONFIG_OF
+static const struct of_device_id omap2430_id_table[] = {
+	{
+		.compatible = "ti,omap4-musb"
+	},
+	{
+		.compatible = "ti,omap3-musb"
+	},
+	{},
+};
+MODULE_DEVICE_TABLE(of, omap2430_id_table);
+#endif
+
 static struct platform_driver omap2430_driver = {
 	.probe		= omap2430_probe,
 	.remove		= __devexit_p(omap2430_remove),
 	.driver		= {
 		.name	= "musb-omap2430",
 		.pm	= DEV_PM_OPS,
+		.of_match_table = of_match_ptr(omap2430_id_table),
 	},
 };
 
-- 
1.7.9.5

[PATCH v7 7/7] arm: omap: phy: remove unused functions from omap-phy-internal.c

[Kishon Vijay Abraham I]

All the unnessary functions in omap-phy-internal is removed.
These functionality are now handled by omap-usb2 phy driver.

Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/mach-omap2/omap_phy_internal.c |  138 -------------------------------
 arch/arm/mach-omap2/twl-common.c        |    5 --
 arch/arm/mach-omap2/usb-musb.c          |    3 -
 3 files changed, 146 deletions(-)

diff --git a/arch/arm/mach-omap2/omap_phy_internal.c b/arch/arm/mach-omap2/omap_phy_internal.c
index d52651a..874aecc 100644
--- a/arch/arm/mach-omap2/omap_phy_internal.c
+++ b/arch/arm/mach-omap2/omap_phy_internal.c
@@ -31,144 +31,6 @@
 #include <plat/usb.h>
 #include "control.h"
 
-/* OMAP control module register for UTMI PHY */
-#define CONTROL_DEV_CONF		0x300
-#define PHY_PD				0x1
-
-#define USBOTGHS_CONTROL		0x33c
-#define	AVALID				BIT(0)
-#define	BVALID				BIT(1)
-#define	VBUSVALID			BIT(2)
-#define	SESSEND				BIT(3)
-#define	IDDIG				BIT(4)
-
-static struct clk *phyclk, *clk48m, *clk32k;
-static void __iomem *ctrl_base;
-static int usbotghs_control;
-
-int omap4430_phy_init(struct device *dev)
-{
-	ctrl_base = ioremap(OMAP443X_SCM_BASE, SZ_1K);
-	if (!ctrl_base) {
-		pr_err("control module ioremap failed\n");
-		return -ENOMEM;
-	}
-	/* Power down the phy */
-	__raw_writel(PHY_PD, ctrl_base + CONTROL_DEV_CONF);
-
-	if (!dev) {
-		iounmap(ctrl_base);
-		return 0;
-	}
-
-	phyclk = clk_get(dev, "ocp2scp_usb_phy_ick");
-	if (IS_ERR(phyclk)) {
-		dev_err(dev, "cannot clk_get ocp2scp_usb_phy_ick\n");
-		iounmap(ctrl_base);
-		return PTR_ERR(phyclk);
-	}
-
-	clk48m = clk_get(dev, "ocp2scp_usb_phy_phy_48m");
-	if (IS_ERR(clk48m)) {
-		dev_err(dev, "cannot clk_get ocp2scp_usb_phy_phy_48m\n");
-		clk_put(phyclk);
-		iounmap(ctrl_base);
-		return PTR_ERR(clk48m);
-	}
-
-	clk32k = clk_get(dev, "usb_phy_cm_clk32k");
-	if (IS_ERR(clk32k)) {
-		dev_err(dev, "cannot clk_get usb_phy_cm_clk32k\n");
-		clk_put(phyclk);
-		clk_put(clk48m);
-		iounmap(ctrl_base);
-		return PTR_ERR(clk32k);
-	}
-	return 0;
-}
-
-int omap4430_phy_set_clk(struct device *dev, int on)
-{
-	static int state;
-
-	if (on && !state) {
-		/* Enable the phy clocks */
-		clk_enable(phyclk);
-		clk_enable(clk48m);
-		clk_enable(clk32k);
-		state = 1;
-	} else if (state) {
-		/* Disable the phy clocks */
-		clk_disable(phyclk);
-		clk_disable(clk48m);
-		clk_disable(clk32k);
-		state = 0;
-	}
-	return 0;
-}
-
-int omap4430_phy_power(struct device *dev, int ID, int on)
-{
-	if (on) {
-		if (ID)
-			/* enable VBUS valid, IDDIG groung */
-			__raw_writel(AVALID | VBUSVALID, ctrl_base +
-							USBOTGHS_CONTROL);
-		else
-			/*
-			 * Enable VBUS Valid, AValid and IDDIG
-			 * high impedance
-			 */
-			__raw_writel(IDDIG | AVALID | VBUSVALID,
-						ctrl_base + USBOTGHS_CONTROL);
-	} else {
-		/* Enable session END and IDIG to high impedance. */
-		__raw_writel(SESSEND | IDDIG, ctrl_base +
-					USBOTGHS_CONTROL);
-	}
-	return 0;
-}
-
-int omap4430_phy_suspend(struct device *dev, int suspend)
-{
-	if (suspend) {
-		/* Disable the clocks */
-		omap4430_phy_set_clk(dev, 0);
-		/* Power down the phy */
-		__raw_writel(PHY_PD, ctrl_base + CONTROL_DEV_CONF);
-
-		/* save the context */
-		usbotghs_control = __raw_readl(ctrl_base + USBOTGHS_CONTROL);
-	} else {
-		/* Enable the internel phy clcoks */
-		omap4430_phy_set_clk(dev, 1);
-		/* power on the phy */
-		if (__raw_readl(ctrl_base + CONTROL_DEV_CONF) & PHY_PD) {
-			__raw_writel(~PHY_PD, ctrl_base + CONTROL_DEV_CONF);
-			mdelay(200);
-		}
-
-		/* restore the context */
-		__raw_writel(usbotghs_control, ctrl_base + USBOTGHS_CONTROL);
-	}
-
-	return 0;
-}
-
-int omap4430_phy_exit(struct device *dev)
-{
-	if (ctrl_base)
-		iounmap(ctrl_base);
-	if (phyclk)
-		clk_put(phyclk);
-	if (clk48m)
-		clk_put(clk48m);
-	if (clk32k)
-		clk_put(clk32k);
-
-	return 0;
-}
-
 void am35x_musb_reset(void)
 {
 	u32	regval;
diff --git a/arch/arm/mach-omap2/twl-common.c b/arch/arm/mach-omap2/twl-common.c
index de47f17..e2cdf67 100644
--- a/arch/arm/mach-omap2/twl-common.c
+++ b/arch/arm/mach-omap2/twl-common.c
@@ -250,11 +250,6 @@ void __init omap3_pmic_get_config(struct twl4030_platform_data *pmic_data,
 
 #if defined(CONFIG_ARCH_OMAP4)
 static struct twl4030_usb_data omap4_usb_pdata = {
-	.phy_init	= omap4430_phy_init,
-	.phy_exit	= omap4430_phy_exit,
-	.phy_power	= omap4430_phy_power,
-	.phy_set_clock	= omap4430_phy_set_clk,
-	.phy_suspend	= omap4430_phy_suspend,
 };
 
 static struct regulator_init_data omap4_vdac_idata = {
diff --git a/arch/arm/mach-omap2/usb-musb.c b/arch/arm/mach-omap2/usb-musb.c
index c4a5768..e9b4b23 100644
--- a/arch/arm/mach-omap2/usb-musb.c
+++ b/arch/arm/mach-omap2/usb-musb.c
@@ -117,7 +117,4 @@ void __init usb_musb_init(struct omap_musb_board_data *musb_board_data)
 	dev->dma_mask = &musb_dmamask;
 	dev->coherent_dma_mask = musb_dmamask;
 	put_device(dev);
-
-	if (cpu_is_omap44xx())
-		omap4430_phy_init(dev);
 }
-- 
1.7.9.5

Re: [PATCH v7 1/7] drivers: usb: phy: add a new driver for omap usb2 phy

[ABRAHAM, KISHON VIJAY]

Hi,

On Mon, Aug 6, 2012 at 6:37 PM, Kishon Vijay Abraham I <kishon@ti.com> wrote:
> All phy related programming like enabling/disabling the clocks, powering
> on/off the phy is taken care of by this driver. It is also used for OTG
> related functionality like srp.
>
> This also includes device tree support for usb2 phy driver and
> the documentation with device tree binding information is updated.
>
> Currently writing to control module register is taken care in this
> driver which will be removed once the control module driver is in place.
>
> Cc: Felipe Balbi <balbi@ti.com>
> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
> ---
>  .../devicetree/bindings/bus/omap-ocp2scp.txt       |    3 +
>  Documentation/devicetree/bindings/usb/omap-usb.txt |   17 ++
>  drivers/usb/phy/Kconfig                            |   10 +
>  drivers/usb/phy/Makefile                           |    1 +
>  drivers/usb/phy/omap-usb2.c                        |  271 ++++++++++++++++++++
>  include/linux/usb/omap_usb.h                       |   46 ++++
>  include/linux/usb/phy_companion.h                  |   34 +++
>  7 files changed, 382 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/usb/omap-usb.txt
>  create mode 100644 drivers/usb/phy/omap-usb2.c
>  create mode 100644 include/linux/usb/omap_usb.h
>  create mode 100644 include/linux/usb/phy_companion.h
>
> diff --git a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
> index d2fe064..bb0c7f4 100644
> --- a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
> +++ b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
> @@ -8,3 +8,6 @@ properties:
>
>  Sub-nodes:
>  All the devices connected to ocp2scp are described using sub-node to ocp2scp
> +- usb2phy :
> +   The binding details of usb2phy can be found in:
> +   Documentation/devicetree/bindings/usb/omap-usb.txt

The above two lines should be added in omap-ocp2scp.txt (this file was
added as part of omap: add ocp2scp as a bus driver and is in
linux-next). However this file is still not in Felipe's xceiv branch.
So I'm not sure how I can get this patch merged in Felipe's tree
without conflict.

Thanks
Kishon

Re: [PATCH v7 1/7] drivers: usb: phy: add a new driver for omap usb2 phy

[Arnd Bergmann]

On Thursday 06 September 2012, ABRAHAM, KISHON VIJAY wrote:
> > diff --git a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
> > index d2fe064..bb0c7f4 100644
> > --- a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
> > +++ b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
> > @@ -8,3 +8,6 @@ properties:
> >
> >  Sub-nodes:
> >  All the devices connected to ocp2scp are described using sub-node to ocp2scp
> > +- usb2phy :
> > +   The binding details of usb2phy can be found in:
> > +   Documentation/devicetree/bindings/usb/omap-usb.txt
> 
> The above two lines should be added in omap-ocp2scp.txt (this file was
> added as part of omap: add ocp2scp as a bus driver and is in
> linux-next). However this file is still not in Felipe's xceiv branch.
> So I'm not sure how I can get this patch merged in Felipe's tree
> without conflict.
> 

There are three possible ways to do that:

* Not add that text. Is is actually required? The ocp2scp bus driver 
doesn't actually care what is connected to it, does it?

* Ask Felipe to merge the drivers/ocp2scp branch from arm-soc into
his branch, then apply your patch on top. The branch is scheduled
for merging in 3.7 and is stable, so there is no harm merging it
into his tree, as long as Olof and I are aware of this.

* Split out this change and apply the patch to add this documentation
change on top of the drivers/ocp2scp branch in the arm-soc tree.
There is no strict dependency between this change and the others
you want to merge, so it does not matter which tree it is merged through.

	Arnd

Re: [PATCH v7 1/7] drivers: usb: phy: add a new driver for omap usb2 phy

[Felipe Balbi]

[-- Attachment #1: Type: text/plain, Size: 1885 bytes --]

On Thu, Sep 06, 2012 at 01:03:02PM +0000, Arnd Bergmann wrote:
> On Thursday 06 September 2012, ABRAHAM, KISHON VIJAY wrote:
> > > diff --git a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
> > > index d2fe064..bb0c7f4 100644
> > > --- a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
> > > +++ b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
> > > @@ -8,3 +8,6 @@ properties:
> > >
> > >  Sub-nodes:
> > >  All the devices connected to ocp2scp are described using sub-node to ocp2scp
> > > +- usb2phy :
> > > +   The binding details of usb2phy can be found in:
> > > +   Documentation/devicetree/bindings/usb/omap-usb.txt
> > 
> > The above two lines should be added in omap-ocp2scp.txt (this file was
> > added as part of omap: add ocp2scp as a bus driver and is in
> > linux-next). However this file is still not in Felipe's xceiv branch.
> > So I'm not sure how I can get this patch merged in Felipe's tree
> > without conflict.
> > 
> 
> There are three possible ways to do that:
> 
> * Not add that text. Is is actually required? The ocp2scp bus driver 
> doesn't actually care what is connected to it, does it?
> 
> * Ask Felipe to merge the drivers/ocp2scp branch from arm-soc into
> his branch, then apply your patch on top. The branch is scheduled
> for merging in 3.7 and is stable, so there is no harm merging it
> into his tree, as long as Olof and I are aware of this.
> 
> * Split out this change and apply the patch to add this documentation
> change on top of the drivers/ocp2scp branch in the arm-soc tree.
> There is no strict dependency between this change and the others
> you want to merge, so it does not matter which tree it is merged through.

I'd be more comfortable with option 3 or 1, whatever you guys decide is
fine ;-)

-- 
balbi

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]