From: Sitsofe Wheeler <sitsofe@gmail.com>
To: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: gregkh@linuxfoundation.org, linux-kernel@vger.kernel.org,
devel@linuxdriverproject.org, ohering@suse.com,
apw@canonical.com, jasowang@redhat.com, jbottomley@parallels.com,
hch@infradead.org, linux-scsi@vger.kernel.org
Subject: Re: [PATCH 1/1] Drivers: scsi: storvsc: Add blist flags
Date: Wed, 23 Jul 2014 11:04:48 +0100 [thread overview]
Message-ID: <20140723100448.GA2540@sucs.org> (raw)
In-Reply-To: <1405983961-18782-1-git-send-email-kys@microsoft.com>
On Mon, Jul 21, 2014 at 04:06:01PM -0700, K. Y. Srinivasan wrote:
> Add blist flags to permit the reading of the VPD pages even when
> the target may claim SPC-2 compliance. MSFT targets currently
> claim SPC-2 compliance while they implement post SPC-2 features.
> With this patch we can correctly handle WRITE_SAME_16 issues.
OK I've just seen this as I was about to post a similar patch to get
discard going on Hyper-V. Will your patches handle Hyper-V pass through devices
that support discard? The SSD I have here reports the following in the Linux
VM:
# sg_vpd -p lbpv /dev/sdc
Logical block provisioning VPD page (SBC):
Unmap command supported (LBPU): 1
Write same (16) with unmap bit supported (LBWS): 0
Write same (10) with unmap bit supported (LBWS10): 0
Logical block provisioning read zeros (LBPRZ): 0
Anchored LBAs supported (ANC_SUP): 1
Threshold exponent: 0
Descriptor present (DP): 0
Provisioning type: 0
# sg_readcap -l /dev/sdc
Read Capacity results:
Protection: prot_en=0, p_type=0, p_i_exponent=0
Logical block provisioning: lbpme=0, lbprz=0
Last logical block address=234441647 (0xdf94baf), Number of logical blocks=234441648
Logical block length=512 bytes
Logical blocks per physical block exponent=0
Lowest aligned logical block address=0
Hence:
Device size: 120034123776 bytes, 114473.5 MiB, 120.03 GB
--
Sitsofe | http://sucs.org/~sits/
next prev parent reply other threads:[~2014-07-23 10:04 UTC|newest]
Thread overview: 46+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-07-21 23:06 [PATCH 1/1] Drivers: scsi: storvsc: Add blist flags K. Y. Srinivasan
2014-07-23 10:04 ` Sitsofe Wheeler [this message]
2014-07-23 11:51 ` Christoph Hellwig
2014-07-23 12:54 ` Sitsofe Wheeler
2014-07-23 14:10 ` Christoph Hellwig
2014-07-23 15:31 ` Sitsofe Wheeler
2014-07-23 15:40 ` KY Srinivasan
2014-07-23 15:39 ` KY Srinivasan
2014-07-23 14:10 ` Sitsofe Wheeler
2014-07-23 14:15 ` Christoph Hellwig
2014-07-23 20:13 ` Sitsofe Wheeler
2014-07-24 7:47 ` [PATCH 0/3] Enable discard on Hyper-V Sitsofe Wheeler
2014-07-24 7:52 ` [PATCH 1/3] [SCSI] Add quirk for forcing logical block provisioning tests Sitsofe Wheeler
2014-07-24 7:56 ` [PATCH 2/3] [SCSI] storvsc: Add Hyper-V " Sitsofe Wheeler
2014-07-24 14:09 ` James Bottomley
2014-07-24 18:03 ` Sitsofe Wheeler
2014-07-24 7:58 ` [PATCH 3/3] [SCSI] Make LBP quirk skip lbpme checks tests Sitsofe Wheeler
2014-07-24 12:22 ` [PATCH v2 " Sitsofe Wheeler
2014-07-24 13:54 ` Martin K. Petersen
2014-07-24 15:34 ` Christoph Hellwig
2014-07-24 15:35 ` Christoph Hellwig
2014-07-24 16:24 ` Sitsofe Wheeler
2014-07-24 15:36 ` Sitsofe Wheeler
2014-07-24 15:54 ` Martin K. Petersen
2014-07-25 16:47 ` KY Srinivasan
2014-07-25 16:57 ` Martin K. Petersen
2014-07-26 13:44 ` KY Srinivasan
2014-07-26 16:54 ` Martin K. Petersen
2014-07-26 17:17 ` KY Srinivasan
2014-07-26 19:25 ` Martin K. Petersen
2014-07-27 2:09 ` KY Srinivasan
2014-07-28 18:50 ` KY Srinivasan
2014-07-28 19:02 ` Martin K. Petersen
2014-07-28 19:05 ` KY Srinivasan
2014-07-28 20:02 ` James Bottomley
2014-07-28 20:05 ` KY Srinivasan
2014-07-29 17:41 ` KY Srinivasan
2014-07-29 19:30 ` Martin K. Petersen
2014-07-25 17:10 ` James Bottomley
2014-07-26 13:42 ` KY Srinivasan
2014-07-24 12:37 ` [PATCH 0/3] Enable discard on Hyper-V Sitsofe Wheeler
2014-07-24 5:40 ` [PATCH 1/1] Drivers: scsi: storvsc: Add blist flags Hannes Reinecke
2014-08-01 19:48 ` Sitsofe Wheeler
-- strict thread matches above, loose matches on Subject: below --
2014-07-21 3:33 K. Y. Srinivasan
2014-07-21 11:27 ` Christoph Hellwig
2014-07-21 13:19 ` KY Srinivasan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20140723100448.GA2540@sucs.org \
--to=sitsofe@gmail.com \
--cc=apw@canonical.com \
--cc=devel@linuxdriverproject.org \
--cc=gregkh@linuxfoundation.org \
--cc=hch@infradead.org \
--cc=jasowang@redhat.com \
--cc=jbottomley@parallels.com \
--cc=kys@microsoft.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-scsi@vger.kernel.org \
--cc=ohering@suse.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).