On Thu, Aug 13, 2015 at 08:37:36AM +0000, John Youn wrote:
> On 8/12/2015 12:33 PM, Felipe Balbi wrote:
> > On Wed, Aug 12, 2015 at 07:06:09PM +0800, Yunzhi Li wrote:
> >> Hi ,
> >> 在 2015/8/11 22:12, Felipe Balbi 写道:
> >>> Hi,
> >>>
> >>> On Tue, Aug 11, 2015 at 10:27:42AM +0800, Yunzhi Li wrote:
> >>>> We initiate dwc2 usb controller in BIOS, when kernel driver
> >>>> start-up we should reset AHB hclk domain to reset all AHB
> >>>> interface registers to default. Without this the FIFO value
> >>>> setting might be incorrect because calculating FIFO size need the
> >>>> power-on value of GRXFSIZ/GNPTXFSIZ/HPTXFSIZ registers.
> >>>>
> >>>> This patch could avoid warnning massage like in rk3288 platform:
> >>>> [    2.074764] dwc2 ff580000.usb: 256 invalid for
> >>>> host_perio_tx_fifo_size. Check HW configuration.
> >>>>
> >>>> Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
> >>>>
> >>>> ---
> >>>>
> >>>>  drivers/usb/dwc2/platform.c | 12 ++++++++++++
> >>>>  1 file changed, 12 insertions(+)
> >>>>
> >>>> diff --git a/drivers/usb/dwc2/platform.c b/drivers/usb/dwc2/platform.c
> >>>> index 9093530..3da21ab 100644
> >>>> --- a/drivers/usb/dwc2/platform.c
> >>>> +++ b/drivers/usb/dwc2/platform.c
> >>>> @@ -42,6 +42,7 @@
> >>>>  #include <linux/of_device.h>
> >>>>  #include <linux/mutex.h>
> >>>>  #include <linux/platform_device.h>
> >>>> +#include <linux/reset.h>
> >>>>  #include <linux/usb/of.h>
> >>>> @@ -165,6 +166,7 @@ static int dwc2_driver_probe(struct platform_device *dev)
> >>>>  	struct resource *res;
> >>>>  	struct phy *phy;
> >>>>  	struct usb_phy *uphy;
> >>>> +	struct reset_control *rst;
> >>>>  	int retval;
> >>>>  	int irq;
> >>>> @@ -189,6 +191,16 @@ static int dwc2_driver_probe(struct platform_device *dev)
> >>>>  	hsotg->dev = &dev->dev;
> >>>> +	/* AHB hclk domain reset, set all AHB interface registers to default */
> >>>> +	rst = devm_reset_control_get_optional(&dev->dev, "ahb_reset");
> >>> why isn't this done in core so PCI systems can also make use of it ?
> >>>
> >> I have no ides about how to reset a PCI interface dwc2 controller, John
> >> could you please give some infomation about it ?
> >> Is it also needed for PCI interface dwc2 IP ?
> > 
> > even on platform only, how do you know all users provide a ahb_reset
> > reset controller ?
> > 
> 
> Also where do you provide the ahb_reset? I don't see it as a
> property for dwc2.
> 
> With regards to PCI, I'm also not sure how you'd accomplish
> something like this. But the platform I use at least doesn't need
> this.

Is the reset controller optional ? That _optional should always return a
valid pointer, right ? Even if that valid pointer is NULL :-)

-- 
balbi