From: Rob Herring <robh@kernel.org>
To: Stephen Boyd <sboyd@codeaurora.org>
Cc: Linus Walleij <linus.walleij@linaro.org>,
linux-kernel@vger.kernel.org, linux-arm-msm@vger.kernel.org,
linux-arm-kernel@lists.infradead.org, linux-gpio@vger.kernel.org,
devicetree@vger.kernel.org, "Ivan T. Ivanov" <iivanov@mm-sol.com>,
Bjorn Andersson <bjorn.andersson@sonymobile.com>
Subject: Re: [RFC/PATCH] pinctrl: qcom: Add generic ssbi and spmi GPIO/MPP bindings
Date: Thu, 19 Nov 2015 08:50:17 -0600 [thread overview]
Message-ID: <20151119145017.GA19795@rob-hp-laptop> (raw)
In-Reply-To: <1447808426-21834-1-git-send-email-sboyd@codeaurora.org>
On Tue, Nov 17, 2015 at 05:00:26PM -0800, Stephen Boyd wrote:
> The drivers don't really need to know which PMIC they're for, so
> make a generic binding for them. This alleviates us from updating
> the drivers every time a new PMIC comes out. It's still
> recommended that we update the binding with new PMIC models and
> always specify the specific model for the MPPs and gpios before
> the generic compatible string in devicetree, but this at least
> cuts down on adding more and more compatible strings to the
> drivers until we actually need them.
>
> Cc: <devicetree@vger.kernel.org>
> Cc: "Ivan T. Ivanov" <iivanov@mm-sol.com>
> Cc: Bjorn Andersson <bjorn.andersson@sonymobile.com>
> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
> ---
Seems okay to me. I assume you are going to update all the dts files?
Rob
>
> We can also figure out the number of the pins from the number
> of interrupts, so we really don't need to even look at the size of the
> reg property or model number for the spmi and ssbi modules. I'll propose
> that change as well tomorrow.
>
> Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt | 5 ++++-
> Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt | 5 ++++-
> drivers/pinctrl/qcom/pinctrl-spmi-gpio.c | 1 +
> drivers/pinctrl/qcom/pinctrl-spmi-mpp.c | 1 +
> 4 files changed, 10 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt
> index a90c812ad642..f1e4643f4132 100644
> --- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt
> +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt
> @@ -17,6 +17,9 @@ PMIC's from Qualcomm.
> "qcom,pm8994-gpio"
> "qcom,pma8084-gpio"
>
> + And must contain either "qcom,spmi-gpio" or "qcom,ssbi-gpio"
> + if the device is on an spmi bus or an ssbi bus respectively
> +
> - reg:
> Usage: required
> Value type: <prop-encoded-array>
> @@ -183,7 +186,7 @@ to specify in a pin configuration subnode:
> Example:
>
> pm8921_gpio: gpio@150 {
> - compatible = "qcom,pm8921-gpio";
> + compatible = "qcom,pm8921-gpio", "qcom,ssbi-gpio";
> reg = <0x150 0x160>;
> interrupts = <192 1>, <193 1>, <194 1>,
> <195 1>, <196 1>, <197 1>,
> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt
> index d74e631e10da..e28320b18ecb 100644
> --- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt
> +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt
> @@ -18,6 +18,9 @@ of PMIC's from Qualcomm.
> "qcom,pm8994-mpp",
> "qcom,pma8084-mpp",
>
> + And must contain either "qcom,spmi-mpp" or "qcom,ssbi-mpp"
> + if the device is on an spmi bus or an ssbi bus respectively.
> +
> - reg:
> Usage: required
> Value type: <prop-encoded-array>
> @@ -157,7 +160,7 @@ to specify in a pin configuration subnode:
> Example:
>
> mpps@a000 {
> - compatible = "qcom,pm8841-mpp";
> + compatible = "qcom,pm8841-mpp", "qcom,spmi-mpp";
> reg = <0xa000>;
> gpio-controller;
> #gpio-cells = <2>;
> diff --git a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
> index df4413023e21..9f9979903fcb 100644
> --- a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
> +++ b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
> @@ -806,6 +806,7 @@ static const struct of_device_id pmic_gpio_of_match[] = {
> { .compatible = "qcom,pm8941-gpio" }, /* 36 GPIO's */
> { .compatible = "qcom,pm8994-gpio" }, /* 22 GPIO's */
> { .compatible = "qcom,pma8084-gpio" }, /* 22 GPIO's */
> + { .compatible = "qcom,spmi-gpio" }, /* Generic */
> { },
> };
>
> diff --git a/drivers/pinctrl/qcom/pinctrl-spmi-mpp.c b/drivers/pinctrl/qcom/pinctrl-spmi-mpp.c
> index 7b4136a22c5b..5a4373dd9c61 100644
> --- a/drivers/pinctrl/qcom/pinctrl-spmi-mpp.c
> +++ b/drivers/pinctrl/qcom/pinctrl-spmi-mpp.c
> @@ -909,6 +909,7 @@ static const struct of_device_id pmic_mpp_of_match[] = {
> { .compatible = "qcom,pm8941-mpp" }, /* 8 MPP's */
> { .compatible = "qcom,pm8994-mpp" }, /* 8 MPP's */
> { .compatible = "qcom,pma8084-mpp" }, /* 8 MPP's */
> + { .compatible = "qcom,spmi-mpp" }, /* Generic */
> { },
> };
>
> --
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> a Linux Foundation Collaborative Project
>
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2015-11-19 14:50 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-11-18 1:00 [RFC/PATCH] pinctrl: qcom: Add generic ssbi and spmi GPIO/MPP bindings Stephen Boyd
2015-11-18 4:09 ` Andy Gross
2015-11-18 19:33 ` [PATCH] pinctrl: qcom: pmic-gpio/mpp: of_irq_count() == npins Stephen Boyd
2015-11-19 6:04 ` Andy Gross
2015-11-23 18:21 ` Bjorn Andersson
2015-12-01 9:02 ` Linus Walleij
2015-11-19 14:50 ` Rob Herring [this message]
2015-11-20 17:53 ` [RFC/PATCH] pinctrl: qcom: Add generic ssbi and spmi GPIO/MPP bindings Stephen Boyd
2015-11-23 6:37 ` Ivan T. Ivanov
2015-11-23 18:22 ` Bjorn Andersson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20151119145017.GA19795@rob-hp-laptop \
--to=robh@kernel.org \
--cc=bjorn.andersson@sonymobile.com \
--cc=devicetree@vger.kernel.org \
--cc=iivanov@mm-sol.com \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=sboyd@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).