From: Rob Herring <robh@kernel.org>
To: Vinay Simha BN <simhavcs@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>,
Pawel Moll <pawel.moll@arm.com>,
Mark Rutland <mark.rutland@arm.com>,
Ian Campbell <ijc+devicetree@hellion.org.uk>,
Kumar Gala <galak@codeaurora.org>,
"open list:DRM PANEL DRIVERS" <dri-devel@lists.freedesktop.org>,
"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
<devicetree@vger.kernel.org>,
open list <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH v2 2/4] dt-bindings: Add jdi lt070me05000 panel bindings
Date: Thu, 21 Apr 2016 10:45:46 -0500 [thread overview]
Message-ID: <20160421154546.GA20028@rob-hp-laptop> (raw)
In-Reply-To: <1461144755-10633-2-git-send-email-simhavcs@gmail.com>
On Wed, Apr 20, 2016 at 03:02:31PM +0530, Vinay Simha BN wrote:
> Add documentation for lt070me05000 panel
>
> Signed-off-by: Vinay Simha BN <simhavcs@gmail.com>
> ---
> .../bindings/display/panel/jdi,lt070me05000.txt | 43 ++++++++++++++++++++++
> 1 file changed, 43 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt
>
> diff --git a/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt b/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt
> new file mode 100644
> index 0000000..ffe0550
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt
> @@ -0,0 +1,43 @@
> +JDI model LT070ME05000 1200x1920 7" DSI Panel
> +
> +Required properties:
> +- compatible: should be "jdi,lt070me05000"
> +- power-supply: phandle of the regulator that provides the supply voltage
> + IOVCC , power supply for LCM (1.8V)
> +- vddp-supply: phandle of the regulator that provides the supply voltage
> + Power IC supply (3-5V)
> +- dcdc_en-supply: phandle of the regulator that provides the supply voltage
> + Power IC supply enable, High active
> +- reset-gpio: phandle of gpio for reset line
> + This should be 8mA, gpio can be configured using mux and pinctrl.
> + XRES, Reset, Low active
> +- enable-gpio: phandle of gpio for enable line
> + LED_EN, LED backlight enable, High active
These should all be -gpios instead.
> +- vcc-gpio: phandle of regulator/gpio that provides the supply voltage
> + VDD, LED power supply (3-5V)
Is it a regulator or gpio?
> +
> +Optional properties:
> +- pwm-gpio: phandle of gpio/pwm
This should use the PWM binding. It may not be a GPIO on some hosts.
> + pwm backlight control, this should be mapped to the backlight level
> + display brightness (0x51)
> +
> +Example:
> +
> + dsi0: qcom,mdss_dsi@4700000 {
> + panel@0 {
> + compatible = "jdi,lt070me05000";
> + reg = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&dsi_panel_pinctrl>;
> +
> + power-supply = <&pm8921_lvs5>;
> + vddp-supply = <&pm8921_l17>;
> + dcdc_en-supply = <&pm8921_lvs7>;
> +
> + reset-gpio = <&tlmm_pinmux 54 0>;
> + enable-gpio = <&pm8921_gpio 36 GPIO_ACTIVE_HIGH>;
> + vcc-gpio = <&pm8921_gpio 23 GPIO_ACTIVE_HIGH>;
> +
> + pwm-gpio = <&pm8921_gpio 26 GPIO_ACTIVE_HIGH>;
> + };
> + };
> --
> 2.1.2
>
next prev parent reply other threads:[~2016-04-21 15:45 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-04-13 6:28 [PATCH] drm/panel: Add JDI LT070ME05000 WUXGA DSI Panel Vinay Simha BN
2016-04-13 13:49 ` Thierry Reding
2016-04-14 12:38 ` Vinay Simha
2016-04-20 9:42 ` Vinay Simha
2016-04-14 10:47 ` [RESEND][PATCH] " Vinay Simha BN
2016-04-14 17:15 ` Rob Herring
2016-04-20 9:32 ` [PATCH v2 1/4] dt-bindings: Add jdi panel vendor Vinay Simha BN
2016-04-20 9:32 ` [PATCH v2 2/4] dt-bindings: Add jdi lt070me05000 panel bindings Vinay Simha BN
2016-04-21 15:45 ` Rob Herring [this message]
2016-04-22 6:55 ` Vinay Simha
2016-04-22 11:59 ` Thierry Reding
2016-04-20 9:32 ` [PATCH v2 3/4] drm/dsi: Implement set tear scanline Vinay Simha BN
2016-04-20 9:53 ` kbuild test robot
2016-04-20 10:24 ` [PATCH v3] drm/dsi: Implement set tear scanline compile fix Vinay Simha BN
2016-04-20 9:32 ` [PATCH v2 4/4] drm/panel: Add JDI LT070ME05000 WUXGA DSI Panel Vinay Simha BN
2016-04-21 15:33 ` [PATCH v2 1/4] dt-bindings: Add jdi panel vendor Rob Herring
2016-04-14 14:40 ` [PATCH] drm/panel: Add JDI LT070ME05000 WUXGA DSI Panel Archit Taneja
2016-04-20 9:46 ` Vinay Simha
2016-07-13 16:44 [PATCH 1/4] dt-bindings: Add Japan Display Inc vendor id Vinay Simha BN
2016-07-13 16:44 ` [PATCH v2 2/4] dt-bindings: Add jdi lt070me05000 panel bindings Vinay Simha BN
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20160421154546.GA20028@rob-hp-laptop \
--to=robh@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dri-devel@lists.freedesktop.org \
--cc=galak@codeaurora.org \
--cc=ijc+devicetree@hellion.org.uk \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=pawel.moll@arm.com \
--cc=simhavcs@gmail.com \
--cc=thierry.reding@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).