* [PATCH 0/2] ARM: dts: imx53: add support for USB armory board
@ 2016-06-21 14:50 andrej
2016-06-21 14:50 ` [PATCH 1/2] devicetree: Add vendor prefix for Inverse Path andrej
2016-06-21 14:50 ` [PATCH 2/2] ARM: dts: imx53: add support for USB armory board andrej
0 siblings, 2 replies; 6+ messages in thread
From: andrej @ 2016-06-21 14:50 UTC (permalink / raw)
To: devicetree
Cc: Shawn Guo, Sascha Hauer, Fabio Estevam, linux-arm-kernel,
linux-kernel, Vagrant Cascadian
From: Andrej Rosano <andrej@inversepath.com>
This two patches add support for the USB armory board.
The USB armory from Inverse Path is an open source hardware design,
implementing a flash drive sized computer:
https://inversepath.com/usbarmory
Andrej Rosano (2):
devicetree: Add vendor prefix for Inverse Path
ARM: dts: imx53: add support for USB armory board
.../devicetree/bindings/vendor-prefixes.txt | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx53-usbarmory.dts | 239 +++++++++++++++++++++
3 files changed, 241 insertions(+)
create mode 100644 arch/arm/boot/dts/imx53-usbarmory.dts
--
2.9.0
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH 1/2] devicetree: Add vendor prefix for Inverse Path
2016-06-21 14:50 [PATCH 0/2] ARM: dts: imx53: add support for USB armory board andrej
@ 2016-06-21 14:50 ` andrej
2016-06-21 21:59 ` Rob Herring
2016-06-21 14:50 ` [PATCH 2/2] ARM: dts: imx53: add support for USB armory board andrej
1 sibling, 1 reply; 6+ messages in thread
From: andrej @ 2016-06-21 14:50 UTC (permalink / raw)
To: devicetree
Cc: Shawn Guo, Sascha Hauer, Fabio Estevam, linux-arm-kernel,
linux-kernel, Vagrant Cascadian
From: Andrej Rosano <andrej@inversepath.com>
Inverse Path is an information security consulting company:
https://inversepath.com
Signed-off-by: Andrej Rosano <andrej@inversepath.com>
---
Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 2c2500d..37bfd91 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -134,6 +134,7 @@ innolux Innolux Corporation
intel Intel Corporation
intercontrol Inter Control Group
invensense InvenSense Inc.
+inversepath Inverse Path
isee ISEE 2007 S.L.
isil Intersil
issi Integrated Silicon Solutions Inc.
--
2.9.0
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH 2/2] ARM: dts: imx53: add support for USB armory board
2016-06-21 14:50 [PATCH 0/2] ARM: dts: imx53: add support for USB armory board andrej
2016-06-21 14:50 ` [PATCH 1/2] devicetree: Add vendor prefix for Inverse Path andrej
@ 2016-06-21 14:50 ` andrej
2016-06-28 1:50 ` Shawn Guo
1 sibling, 1 reply; 6+ messages in thread
From: andrej @ 2016-06-21 14:50 UTC (permalink / raw)
To: devicetree
Cc: Shawn Guo, Sascha Hauer, Fabio Estevam, linux-arm-kernel,
linux-kernel, Vagrant Cascadian
From: Andrej Rosano <andrej@inversepath.com>
Add support for Inverse Path USB armory board, an open source
flash-drive sized computer based on NXP i.MX53 SoC.
https://inversepath.com/usbarmory
Signed-off-by: Andrej Rosano <andrej@inversepath.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx53-usbarmory.dts | 239 ++++++++++++++++++++++++++++++++++
2 files changed, 240 insertions(+)
create mode 100644 arch/arm/boot/dts/imx53-usbarmory.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 414b427..f8f85ab 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -303,6 +303,7 @@ dtb-$(CONFIG_SOC_IMX53) += \
imx53-smd.dtb \
imx53-tx53-x03x.dtb \
imx53-tx53-x13x.dtb \
+ imx53-usbarmory.dtb \
imx53-voipac-bsb.dtb
dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-apf6dev.dtb \
diff --git a/arch/arm/boot/dts/imx53-usbarmory.dts b/arch/arm/boot/dts/imx53-usbarmory.dts
new file mode 100644
index 0000000..9a172fd
--- /dev/null
+++ b/arch/arm/boot/dts/imx53-usbarmory.dts
@@ -0,0 +1,239 @@
+/*
+ * USB armory MkI device tree include file
+ * https://inversepath.com/usbarmory
+ *
+ * Copyright (C) 2015, Inverse Path
+ * Andrej Rosano <andrej@inversepath.com>
+ *
+ * Licensed under GPLv2
+ */
+
+/dts-v1/;
+#include "imx53.dtsi"
+
+/ {
+ model = "Inverse Path USB armory";
+ compatible = "inversepath,imx53-usbarmory", "fsl,imx53";
+};
+
+/ {
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ memory {
+ reg = <0x70000000 0x20000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pin_gpio4_27>;
+
+ user {
+ label = "LED";
+ gpios = <&gpio4 27 0>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&cpu0 {
+ operating-points = <
+ /* kHz */
+ 166666 850000
+ 400000 900000
+ 800000 1050000
+ >;
+};
+
+&esdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_esdhc1>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+
+ imx53-usbarmory {
+ led_pin_gpio4_27: led_gpio4_27@0 {
+ fsl,pins = <
+ MX53_PAD_DISP0_DAT6__GPIO4_27 0x0
+ >;
+ };
+
+ pinctrl_esdhc1: esdhc1grp {
+ fsl,pins = <
+ MX53_PAD_SD1_DATA0__ESDHC1_DAT0 0x1d5
+ MX53_PAD_SD1_DATA1__ESDHC1_DAT1 0x1d5
+ MX53_PAD_SD1_DATA2__ESDHC1_DAT2 0x1d5
+ MX53_PAD_SD1_DATA3__ESDHC1_DAT3 0x1d5
+ MX53_PAD_SD1_CMD__ESDHC1_CMD 0x1d5
+ MX53_PAD_SD1_CLK__ESDHC1_CLK 0x1d5
+ >;
+ };
+
+ pinctrl_i2c1_pmic: i2c1grp_pmic {
+ fsl,pins = <
+ MX53_PAD_EIM_D21__I2C1_SCL 0x0
+ MX53_PAD_EIM_D28__I2C1_SDA 0x0
+ >;
+ };
+
+ /*
+ * UART mode pin header configration
+ * 3 - GPIO5[26], pull-down 100K
+ * 4 - GPIO5[27], pull-down 100K
+ * 5 - TX, pull-up 100K
+ * 6 - RX, pull-up 100K
+ * 7 - GPIO5[30], pull-down 100K
+ */
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX53_PAD_CSI0_DAT8__GPIO5_26 0xc0
+ MX53_PAD_CSI0_DAT9__GPIO5_27 0xc0
+ MX53_PAD_CSI0_DAT10__UART1_TXD_MUX 0x1e4
+ MX53_PAD_CSI0_DAT11__UART1_RXD_MUX 0x1e4
+ MX53_PAD_CSI0_DAT12__GPIO5_30 0xc0
+ >;
+ };
+
+ /*
+ * GPIO mode pin header configuration
+ * 3 - GPIO5[26], pull-down 100K
+ * 4 - GPIO5[27], pull-down 100K
+ * 5 - GPIO5[28], pull-down 100K
+ * 6 - GPIO5[29], pull-down 100K
+ * 7 - GPIO5[30], pull-down 100K
+ */
+ pinctrl_gpio5: gpio5grp {
+ fsl,pins = <
+ MX53_PAD_CSI0_DAT8__GPIO5_26 0xc0
+ MX53_PAD_CSI0_DAT9__GPIO5_27 0xc0
+ MX53_PAD_CSI0_DAT10__GPIO5_28 0xc0
+ MX53_PAD_CSI0_DAT11__GPIO5_29 0xc0
+ MX53_PAD_CSI0_DAT12__GPIO5_30 0xc0
+ >;
+ };
+
+ /*
+ * SPI mode pin header configuration
+ * 3 - SCLK
+ * 4 - MOSI
+ * 5 - MISO
+ * 6 - /SS0
+ * 7 - /SS1
+ */
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX53_PAD_CSI0_DAT8__ECSPI2_SCLK 0x0
+ MX53_PAD_CSI0_DAT9__ECSPI2_MOSI 0x0
+ MX53_PAD_CSI0_DAT10__ECSPI2_MISO 0x0
+ MX53_PAD_CSI0_DAT11__GPIO5_29 0x0
+ MX53_PAD_CSI0_DAT12__GPIO5_30 0x0
+ >;
+ };
+
+ /*
+ * I2C mode pin header configuration
+ * 3 - SDA
+ * 4 - SCL
+ * 5 - GPIO5[28], pull-down 100K
+ * 6 - GPIO5[29], pull-down 100K
+ * 7 - GPIO5[30], pull-down 100K
+ */
+ pinctrl_i2c1_pinheader: i2c1grp_pinheader {
+ fsl,pins = <
+ MX53_PAD_CSI0_DAT8__I2C1_SDA 0x0
+ MX53_PAD_CSI0_DAT9__I2C1_SCL 0x0
+ MX53_PAD_CSI0_DAT10__GPIO5_28 0xc0
+ MX53_PAD_CSI0_DAT11__GPIO5_29 0xc0
+ MX53_PAD_CSI0_DAT12__GPIO5_30 0xc0
+ >;
+ };
+ };
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&usbotg {
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-0 = <&pinctrl_i2c1_pmic>;
+ status = "okay";
+ ltc3589: pmic@34 {
+ compatible = "lltc,ltc3589-2";
+ reg = <0x34>;
+ regulators {
+ sw1_reg: sw1 {
+ regulator-min-microvolt = <591930>;
+ regulator-max-microvolt = <1224671>;
+ lltc,fb-voltage-divider = <100000 158000>;
+ regulator-ramp-delay = <7000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <704123>;
+ regulator-max-microvolt = <1456803>;
+ lltc,fb-voltage-divider = <180000 191000>;
+ regulator-ramp-delay = <7000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3_reg: sw3 {
+ regulator-min-microvolt = <1341250>;
+ regulator-max-microvolt = <2775000>;
+ lltc,fb-voltage-divider = <270000 100000>;
+ regulator-ramp-delay = <7000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bb_out_reg: bb-out {
+ regulator-min-microvolt = <3387341>;
+ regulator-max-microvolt = <3387341>;
+ lltc,fb-voltage-divider = <511000 158000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ ldo1_reg: ldo1 {
+ regulator-min-microvolt = <1306329>;
+ regulator-max-microvolt = <1306329>;
+ lltc,fb-voltage-divider = <100000 158000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo2_reg: ldo2 {
+ regulator-min-microvolt = <704123>;
+ regulator-max-microvolt = <1456806>;
+ lltc,fb-voltage-divider = <180000 191000>;
+ regulator-ramp-delay = <7000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo3_reg: ldo3 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-boot-on;
+ };
+
+ ldo4_reg: ldo4 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3200000>;
+ };
+ };
+ };
+};
--
2.9.0
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH 1/2] devicetree: Add vendor prefix for Inverse Path
2016-06-21 14:50 ` [PATCH 1/2] devicetree: Add vendor prefix for Inverse Path andrej
@ 2016-06-21 21:59 ` Rob Herring
0 siblings, 0 replies; 6+ messages in thread
From: Rob Herring @ 2016-06-21 21:59 UTC (permalink / raw)
To: andrej
Cc: devicetree, Vagrant Cascadian, linux-kernel, Sascha Hauer,
Fabio Estevam, Shawn Guo, linux-arm-kernel
On Tue, Jun 21, 2016 at 04:50:52PM +0200, andrej@inversepath.com wrote:
> From: Andrej Rosano <andrej@inversepath.com>
>
> Inverse Path is an information security consulting company:
> https://inversepath.com
>
> Signed-off-by: Andrej Rosano <andrej@inversepath.com>
> ---
> Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
> 1 file changed, 1 insertion(+)
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 2/2] ARM: dts: imx53: add support for USB armory board
2016-06-21 14:50 ` [PATCH 2/2] ARM: dts: imx53: add support for USB armory board andrej
@ 2016-06-28 1:50 ` Shawn Guo
2016-06-28 13:24 ` Andrej Rosano
0 siblings, 1 reply; 6+ messages in thread
From: Shawn Guo @ 2016-06-28 1:50 UTC (permalink / raw)
To: andrej
Cc: devicetree, Vagrant Cascadian, linux-kernel, Sascha Hauer,
Fabio Estevam, linux-arm-kernel
On Tue, Jun 21, 2016 at 04:50:53PM +0200, andrej@inversepath.com wrote:
> From: Andrej Rosano <andrej@inversepath.com>
>
> Add support for Inverse Path USB armory board, an open source
> flash-drive sized computer based on NXP i.MX53 SoC.
>
> https://inversepath.com/usbarmory
>
> Signed-off-by: Andrej Rosano <andrej@inversepath.com>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx53-usbarmory.dts | 239 ++++++++++++++++++++++++++++++++++
> 2 files changed, 240 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx53-usbarmory.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 414b427..f8f85ab 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -303,6 +303,7 @@ dtb-$(CONFIG_SOC_IMX53) += \
> imx53-smd.dtb \
> imx53-tx53-x03x.dtb \
> imx53-tx53-x13x.dtb \
> + imx53-usbarmory.dtb \
> imx53-voipac-bsb.dtb
> dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6dl-apf6dev.dtb \
> diff --git a/arch/arm/boot/dts/imx53-usbarmory.dts b/arch/arm/boot/dts/imx53-usbarmory.dts
> new file mode 100644
> index 0000000..9a172fd
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx53-usbarmory.dts
> @@ -0,0 +1,239 @@
> +/*
> + * USB armory MkI device tree include file
> + * https://inversepath.com/usbarmory
> + *
> + * Copyright (C) 2015, Inverse Path
> + * Andrej Rosano <andrej@inversepath.com>
> + *
> + * Licensed under GPLv2
> + */
Maybe GPL/X11 dual licence to consider non-Linux users. There are
plenty of dual licence examples under arch/arm/boot/dts.
> +
> +/dts-v1/;
> +#include "imx53.dtsi"
> +
> +/ {
> + model = "Inverse Path USB armory";
> + compatible = "inversepath,imx53-usbarmory", "fsl,imx53";
> +};
> +
> +/ {
> + chosen {
> + stdout-path = &uart1;
> + };
> +
> + memory {
> + reg = <0x70000000 0x20000000>;
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&led_pin_gpio4_27>;
> +
> + user {
> + label = "LED";
> + gpios = <&gpio4 27 0>;
Use the macro in include/dt-bindings/gpio/gpio.h for polarity.
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +};
> +
> +&cpu0 {
> + operating-points = <
> + /* kHz */
> + 166666 850000
> + 400000 900000
> + 800000 1050000
> + >;
Can you put some comments in there explaining why you need a custom opp
table for the board?
> +};
> +
> +&esdhc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_esdhc1>;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl-names = "default";
The property makes no sense where there is no pinctrl-0 property.
> +
> + imx53-usbarmory {
This container node can be dropped to save an indentation level.
> + led_pin_gpio4_27: led_gpio4_27@0 {
Can this node be named in a similar scheme as other pinctrl entries?
> + fsl,pins = <
> + MX53_PAD_DISP0_DAT6__GPIO4_27 0x0
> + >;
> + };
> +
> + pinctrl_esdhc1: esdhc1grp {
> + fsl,pins = <
> + MX53_PAD_SD1_DATA0__ESDHC1_DAT0 0x1d5
> + MX53_PAD_SD1_DATA1__ESDHC1_DAT1 0x1d5
> + MX53_PAD_SD1_DATA2__ESDHC1_DAT2 0x1d5
> + MX53_PAD_SD1_DATA3__ESDHC1_DAT3 0x1d5
> + MX53_PAD_SD1_CMD__ESDHC1_CMD 0x1d5
> + MX53_PAD_SD1_CLK__ESDHC1_CLK 0x1d5
> + >;
> + };
> +
> + pinctrl_i2c1_pmic: i2c1grp_pmic {
Please try to sort these pinctrl entries alphabetically.
> + fsl,pins = <
> + MX53_PAD_EIM_D21__I2C1_SCL 0x0
> + MX53_PAD_EIM_D28__I2C1_SDA 0x0
> + >;
> + };
> +
> + /*
> + * UART mode pin header configration
> + * 3 - GPIO5[26], pull-down 100K
> + * 4 - GPIO5[27], pull-down 100K
> + * 5 - TX, pull-up 100K
> + * 6 - RX, pull-up 100K
> + * 7 - GPIO5[30], pull-down 100K
> + */
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + MX53_PAD_CSI0_DAT8__GPIO5_26 0xc0
> + MX53_PAD_CSI0_DAT9__GPIO5_27 0xc0
> + MX53_PAD_CSI0_DAT10__UART1_TXD_MUX 0x1e4
> + MX53_PAD_CSI0_DAT11__UART1_RXD_MUX 0x1e4
> + MX53_PAD_CSI0_DAT12__GPIO5_30 0xc0
> + >;
> + };
> +
> + /*
> + * GPIO mode pin header configuration
> + * 3 - GPIO5[26], pull-down 100K
> + * 4 - GPIO5[27], pull-down 100K
> + * 5 - GPIO5[28], pull-down 100K
> + * 6 - GPIO5[29], pull-down 100K
> + * 7 - GPIO5[30], pull-down 100K
> + */
> + pinctrl_gpio5: gpio5grp {
The entry is referenced nowhere.
> + fsl,pins = <
> + MX53_PAD_CSI0_DAT8__GPIO5_26 0xc0
> + MX53_PAD_CSI0_DAT9__GPIO5_27 0xc0
> + MX53_PAD_CSI0_DAT10__GPIO5_28 0xc0
> + MX53_PAD_CSI0_DAT11__GPIO5_29 0xc0
> + MX53_PAD_CSI0_DAT12__GPIO5_30 0xc0
> + >;
> + };
> +
> + /*
> + * SPI mode pin header configuration
> + * 3 - SCLK
> + * 4 - MOSI
> + * 5 - MISO
> + * 6 - /SS0
> + * 7 - /SS1
> + */
> + pinctrl_ecspi2: ecspi2grp {
> + fsl,pins = <
> + MX53_PAD_CSI0_DAT8__ECSPI2_SCLK 0x0
> + MX53_PAD_CSI0_DAT9__ECSPI2_MOSI 0x0
> + MX53_PAD_CSI0_DAT10__ECSPI2_MISO 0x0
> + MX53_PAD_CSI0_DAT11__GPIO5_29 0x0
> + MX53_PAD_CSI0_DAT12__GPIO5_30 0x0
> + >;
> + };
> +
> + /*
> + * I2C mode pin header configuration
> + * 3 - SDA
> + * 4 - SCL
> + * 5 - GPIO5[28], pull-down 100K
> + * 6 - GPIO5[29], pull-down 100K
> + * 7 - GPIO5[30], pull-down 100K
> + */
> + pinctrl_i2c1_pinheader: i2c1grp_pinheader {
The entry is referenced nowhere.
> + fsl,pins = <
> + MX53_PAD_CSI0_DAT8__I2C1_SDA 0x0
> + MX53_PAD_CSI0_DAT9__I2C1_SCL 0x0
> + MX53_PAD_CSI0_DAT10__GPIO5_28 0xc0
> + MX53_PAD_CSI0_DAT11__GPIO5_29 0xc0
> + MX53_PAD_CSI0_DAT12__GPIO5_30 0xc0
> + >;
> + };
> + };
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1>;
> + status = "okay";
> +};
> +
> +&usbotg {
> + dr_mode = "peripheral";
> + status = "okay";
> +};
> +
> +&i2c1 {
Please sort these nodes alphabetically in label name.
> + pinctrl-0 = <&pinctrl_i2c1_pmic>;
> + status = "okay";
Have a newline between property list and sub-node.
> + ltc3589: pmic@34 {
> + compatible = "lltc,ltc3589-2";
> + reg = <0x34>;
Ditto
Shawn
> + regulators {
> + sw1_reg: sw1 {
> + regulator-min-microvolt = <591930>;
> + regulator-max-microvolt = <1224671>;
> + lltc,fb-voltage-divider = <100000 158000>;
> + regulator-ramp-delay = <7000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + sw2_reg: sw2 {
> + regulator-min-microvolt = <704123>;
> + regulator-max-microvolt = <1456803>;
> + lltc,fb-voltage-divider = <180000 191000>;
> + regulator-ramp-delay = <7000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + sw3_reg: sw3 {
> + regulator-min-microvolt = <1341250>;
> + regulator-max-microvolt = <2775000>;
> + lltc,fb-voltage-divider = <270000 100000>;
> + regulator-ramp-delay = <7000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + bb_out_reg: bb-out {
> + regulator-min-microvolt = <3387341>;
> + regulator-max-microvolt = <3387341>;
> + lltc,fb-voltage-divider = <511000 158000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> + ldo1_reg: ldo1 {
> + regulator-min-microvolt = <1306329>;
> + regulator-max-microvolt = <1306329>;
> + lltc,fb-voltage-divider = <100000 158000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo2_reg: ldo2 {
> + regulator-min-microvolt = <704123>;
> + regulator-max-microvolt = <1456806>;
> + lltc,fb-voltage-divider = <180000 191000>;
> + regulator-ramp-delay = <7000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo3_reg: ldo3 {
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + regulator-boot-on;
> + };
> +
> + ldo4_reg: ldo4 {
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <3200000>;
> + };
> + };
> + };
> +};
> --
> 2.9.0
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 2/2] ARM: dts: imx53: add support for USB armory board
2016-06-28 1:50 ` Shawn Guo
@ 2016-06-28 13:24 ` Andrej Rosano
0 siblings, 0 replies; 6+ messages in thread
From: Andrej Rosano @ 2016-06-28 13:24 UTC (permalink / raw)
To: Shawn Guo
Cc: devicetree, Vagrant Cascadian, linux-kernel, Sascha Hauer,
Fabio Estevam, linux-arm-kernel
On 2016-06-28, Shawn Guo wrote:
> Maybe GPL/X11 dual licence to consider non-Linux users. There are
> plenty of dual licence examples under arch/arm/boot/dts.
Applied this change along with the others you suggested in the patchset v2.
Thanks,
Andrej
--
Andrej Rosano Inverse Path Srl
<andrej@inversepath.com> http://www.inversepath.com
0x01939B21 5BB8 574E 68E8 D841 E18F D5E9 CEAD E0CF 0193 9B21
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2016-06-28 13:35 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-06-21 14:50 [PATCH 0/2] ARM: dts: imx53: add support for USB armory board andrej
2016-06-21 14:50 ` [PATCH 1/2] devicetree: Add vendor prefix for Inverse Path andrej
2016-06-21 21:59 ` Rob Herring
2016-06-21 14:50 ` [PATCH 2/2] ARM: dts: imx53: add support for USB armory board andrej
2016-06-28 1:50 ` Shawn Guo
2016-06-28 13:24 ` Andrej Rosano
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).