* [PATCH v2 0/3] ARM64: amlogic: Add support for GXL SoC Family
@ 2016-09-14 20:08 Neil Armstrong
2016-09-14 20:08 ` [PATCH v2 1/3] ARM64: dts: amlogic: Add Meson GX dtsi from GXBB Neil Armstrong
` (2 more replies)
0 siblings, 3 replies; 4+ messages in thread
From: Neil Armstrong @ 2016-09-14 20:08 UTC (permalink / raw)
To: afaerber, khilman, carlo
Cc: Neil Armstrong, devicetree, linux-kernel, linux-arm-kernel,
linux-amlogic
The new Amlogic GXL SoCs (S905X and S905D) are part of the Meson GX family and
share some common features that can be described in a common GX dtsi file used
by the Meson GXBB and Meson GXL Family dtsi.
This patchset introduces the common GX dtsi and switches the GXBB to use
the common GX dtsi.
Then it introduces the GXL S905X SoC with the GXL common dtsi, then the S905D
dtsi and the p212 board dts.
Finally the GXL S905D SoC is introduced with a S905D dtsi using the GXL common
and the p23x Board dtsi for the p231 and p230 development boards.
Changes since v1 at http://lkml.kernel.org/r/20160903082227.30559-1-narmstrong@baylibre.com :
- Add missing copyrigh in gx dtsi
- Rename gxl SoCs compatibles to amlogic,s905x and amlogic,s905d
Changes since RFC v1:
- Merge GX common and GXBB changes in a single patch
- Integrate GXL S905X patch
- Add support for S905D and the p23x boards
Note: This patchset integrates the patch "ARM64: dts: amlogic: Add basic support for Amlogic S905X" [1]
from Carlo Caione.
[1] http://lkml.kernel.org/r/1472382113-10754-1-git-send-email-carlo@caione.org
Carlo Caione (1):
ARM64: dts: amlogic: Add basic support for Amlogic S905X
Neil Armstrong (2):
ARM64: dts: amlogic: Add Meson GX dtsi from GXBB
ARM64: dts: amlogic: Add basic support for Amlogic S905D
Documentation/devicetree/bindings/arm/amlogic.txt | 11 +
arch/arm64/boot/dts/amlogic/Makefile | 3 +
arch/arm64/boot/dts/amlogic/meson-gx.dtsi | 200 +++++
arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi | 895 +++++++++------------
.../boot/dts/amlogic/meson-gxl-s905d-p230.dts | 51 ++
.../boot/dts/amlogic/meson-gxl-s905d-p231.dts | 51 ++
.../boot/dts/amlogic/meson-gxl-s905d-p23x.dtsi | 64 ++
arch/arm64/boot/dts/amlogic/meson-gxl-s905d.dtsi | 48 ++
.../boot/dts/amlogic/meson-gxl-s905x-p212.dts | 69 ++
arch/arm64/boot/dts/amlogic/meson-gxl-s905x.dtsi | 48 ++
arch/arm64/boot/dts/amlogic/meson-gxl.dtsi | 48 ++
11 files changed, 972 insertions(+), 516 deletions(-)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-gx.dtsi
create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts
create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p231.dts
create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p23x.dtsi
create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905d.dtsi
create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dts
create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905x.dtsi
create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
--
2.7.0
^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH v2 1/3] ARM64: dts: amlogic: Add Meson GX dtsi from GXBB
2016-09-14 20:08 [PATCH v2 0/3] ARM64: amlogic: Add support for GXL SoC Family Neil Armstrong
@ 2016-09-14 20:08 ` Neil Armstrong
2016-09-14 20:08 ` [PATCH v2 2/3] ARM64: dts: amlogic: Add basic support for Amlogic S905X Neil Armstrong
2016-09-14 20:08 ` [PATCH v2 3/3] ARM64: dts: amlogic: Add basic support for Amlogic S905D Neil Armstrong
2 siblings, 0 replies; 4+ messages in thread
From: Neil Armstrong @ 2016-09-14 20:08 UTC (permalink / raw)
To: afaerber, khilman, carlo
Cc: Neil Armstrong, devicetree, linux-kernel, linux-arm-kernel,
linux-amlogic
Move all non-gxbb specific nodes to a common GX dtsi.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
arch/arm64/boot/dts/amlogic/meson-gx.dtsi | 200 +++++++
arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi | 895 ++++++++++++----------------
2 files changed, 579 insertions(+), 516 deletions(-)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-gx.dtsi
diff --git a/arch/arm64/boot/dts/amlogic/meson-gx.dtsi b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
new file mode 100644
index 0000000..a739d6a
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
@@ -0,0 +1,200 @@
+/*
+ * Copyright (c) 2016 BayLibre, SAS.
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ *
+ * Copyright (c) 2016 Endless Computers, Inc.
+ * Author: Carlo Caione <carlo@endlessm.com>
+ *
+ * Copyright (c) 2016 Andreas Färber
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus {
+ #address-cells = <0x2>;
+ #size-cells = <0x0>;
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x0>;
+ enable-method = "psci";
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x1>;
+ enable-method = "psci";
+ };
+
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x2>;
+ enable-method = "psci";
+ };
+
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x3>;
+ enable-method = "psci";
+ };
+ };
+
+ arm-pmu {
+ compatible = "arm,cortex-a53-pmu";
+ interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>;
+ };
+
+ xtal: xtal-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "xtal";
+ #clock-cells = <0>;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ cbus: cbus@c1100000 {
+ compatible = "simple-bus";
+ reg = <0x0 0xc1100000 0x0 0x100000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0xc1100000 0x0 0x100000>;
+
+ uart_A: serial@84c0 {
+ compatible = "amlogic,meson-uart";
+ reg = <0x0 0x84c0 0x0 0x14>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>;
+ status = "disabled";
+ };
+ };
+
+ gic: interrupt-controller@c4301000 {
+ compatible = "arm,gic-400";
+ reg = <0x0 0xc4301000 0 0x1000>,
+ <0x0 0xc4302000 0 0x2000>,
+ <0x0 0xc4304000 0 0x2000>,
+ <0x0 0xc4306000 0 0x2000>;
+ interrupt-controller;
+ interrupts = <GIC_PPI 9
+ (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+ };
+
+ aobus: aobus@c8100000 {
+ compatible = "simple-bus";
+ reg = <0x0 0xc8100000 0x0 0x100000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0xc8100000 0x0 0x100000>;
+
+ uart_AO: serial@4c0 {
+ compatible = "amlogic,meson-uart";
+ reg = <0x0 0x004c0 0x0 0x14>;
+ interrupts = <GIC_SPI 193 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>;
+ status = "disabled";
+ };
+ };
+
+ periphs: periphs@c8834000 {
+ compatible = "simple-bus";
+ reg = <0x0 0xc8834000 0x0 0x2000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0xc8834000 0x0 0x2000>;
+ };
+
+
+ hiubus: hiubus@c883c000 {
+ compatible = "simple-bus";
+ reg = <0x0 0xc883c000 0x0 0x2000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0xc883c000 0x0 0x2000>;
+ };
+
+ apb: apb@d0000000 {
+ compatible = "simple-bus";
+ reg = <0x0 0xd0000000 0x0 0x200000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0xd0000000 0x0 0x200000>;
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
index 4e9cd01..443811b 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
@@ -40,9 +40,7 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include "meson-gx.dtsi"
#include <dt-bindings/gpio/meson-gxbb-gpio.h>
#include <dt-bindings/reset/amlogic,meson-gxbb-reset.h>
#include <dt-bindings/clock/gxbb-clkc.h>
@@ -51,56 +49,6 @@
/ {
compatible = "amlogic,meson-gxbb";
- interrupt-parent = <&gic>;
- #address-cells = <2>;
- #size-cells = <2>;
-
- cpus {
- #address-cells = <0x2>;
- #size-cells = <0x0>;
-
- cpu0: cpu@0 {
- device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
- reg = <0x0 0x0>;
- enable-method = "psci";
- };
-
- cpu1: cpu@1 {
- device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
- reg = <0x0 0x1>;
- enable-method = "psci";
- };
-
- cpu2: cpu@2 {
- device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
- reg = <0x0 0x2>;
- enable-method = "psci";
- };
-
- cpu3: cpu@3 {
- device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
- reg = <0x0 0x3>;
- enable-method = "psci";
- };
- };
-
- arm-pmu {
- compatible = "arm,cortex-a53-pmu";
- interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
- };
-
- psci {
- compatible = "arm,psci-0.2";
- method = "smc";
- };
firmware {
sm: secure-monitor {
@@ -126,31 +74,7 @@
};
};
- timer {
- compatible = "arm,armv8-timer";
- interrupts = <GIC_PPI 13
- (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>,
- <GIC_PPI 14
- (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>,
- <GIC_PPI 11
- (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>,
- <GIC_PPI 10
- (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>;
- };
-
- xtal: xtal-clk {
- compatible = "fixed-clock";
- clock-frequency = <24000000>;
- clock-output-names = "xtal";
- #clock-cells = <0>;
- };
-
soc {
- compatible = "simple-bus";
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
-
usb0_phy: phy@c0000000 {
compatible = "amlogic,meson-gxbb-usb2-phy";
#phy-cells = <0>;
@@ -170,500 +94,439 @@
status = "disabled";
};
- cbus: cbus@c1100000 {
- compatible = "simple-bus";
- reg = <0x0 0xc1100000 0x0 0x100000>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges = <0x0 0x0 0x0 0xc1100000 0x0 0x100000>;
+ usb0: usb@c9000000 {
+ compatible = "amlogic,meson-gxbb-usb", "snps,dwc2";
+ reg = <0x0 0xc9000000 0x0 0x40000>;
+ interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clkc CLKID_USB0_DDR_BRIDGE>;
+ clock-names = "otg";
+ phys = <&usb0_phy>;
+ phy-names = "usb2-phy";
+ dr_mode = "host";
+ status = "disabled";
+ };
- reset: reset-controller@4404 {
- compatible = "amlogic,meson-gxbb-reset";
- reg = <0x0 0x04404 0x0 0x20>;
- #reset-cells = <1>;
- };
+ usb1: usb@c9100000 {
+ compatible = "amlogic,meson-gxbb-usb", "snps,dwc2";
+ reg = <0x0 0xc9100000 0x0 0x40000>;
+ interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clkc CLKID_USB1_DDR_BRIDGE>;
+ clock-names = "otg";
+ phys = <&usb1_phy>;
+ phy-names = "usb2-phy";
+ dr_mode = "host";
+ status = "disabled";
+ };
- uart_A: serial@84c0 {
- compatible = "amlogic,meson-uart";
- reg = <0x0 0x84c0 0x0 0x14>;
- interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
- clocks = <&xtal>;
- status = "disabled";
- };
+ ethmac: ethernet@c9410000 {
+ compatible = "amlogic,meson-gxbb-dwmac", "snps,dwmac";
+ reg = <0x0 0xc9410000 0x0 0x10000
+ 0x0 0xc8834540 0x0 0x4>;
+ interrupts = <0 8 1>;
+ interrupt-names = "macirq";
+ clocks = <&clkc CLKID_ETH>,
+ <&clkc CLKID_FCLK_DIV2>,
+ <&clkc CLKID_MPLL2>;
+ clock-names = "stmmaceth", "clkin0", "clkin1";
+ phy-mode = "rgmii";
+ status = "disabled";
+ };
+ };
+};
+
+&cbus {
+ reset: reset-controller@4404 {
+ compatible = "amlogic,meson-gxbb-reset";
+ reg = <0x0 0x04404 0x0 0x20>;
+ #reset-cells = <1>;
+ };
+
+ uart_B: serial@84dc {
+ compatible = "amlogic,meson-uart";
+ reg = <0x0 0x84dc 0x0 0x14>;
+ interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>;
+ status = "disabled";
+ };
+
+ pwm_ab: pwm@8550 {
+ compatible = "amlogic,meson-gxbb-pwm";
+ reg = <0x0 0x08550 0x0 0x10>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ pwm_cd: pwm@8650 {
+ compatible = "amlogic,meson-gxbb-pwm";
+ reg = <0x0 0x08650 0x0 0x10>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ pwm_ef: pwm@86c0 {
+ compatible = "amlogic,meson-gxbb-pwm";
+ reg = <0x0 0x086c0 0x0 0x10>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ uart_C: serial@8700 {
+ compatible = "amlogic,meson-uart";
+ reg = <0x0 0x8700 0x0 0x14>;
+ interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>;
+ status = "disabled";
+ };
+
+ watchdog@98d0 {
+ compatible = "amlogic,meson-gxbb-wdt";
+ reg = <0x0 0x098d0 0x0 0x10>;
+ clocks = <&xtal>;
+ };
+
+ spifc: spi@8c80 {
+ compatible = "amlogic,meson-gxbb-spifc";
+ reg = <0x0 0x08c80 0x0 0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clkc CLKID_SPI>;
+ status = "disabled";
+ };
+
+ i2c_A: i2c@8500 {
+ compatible = "amlogic,meson-gxbb-i2c";
+ reg = <0x0 0x08500 0x0 0x20>;
+ interrupts = <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc CLKID_I2C>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c_B: i2c@87c0 {
+ compatible = "amlogic,meson-gxbb-i2c";
+ reg = <0x0 0x087c0 0x0 0x20>;
+ interrupts = <GIC_SPI 214 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc CLKID_I2C>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c_C: i2c@87e0 {
+ compatible = "amlogic,meson-gxbb-i2c";
+ reg = <0x0 0x087e0 0x0 0x20>;
+ interrupts = <GIC_SPI 215 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc CLKID_I2C>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+};
+
+&aobus {
+ pinctrl_aobus: pinctrl@14 {
+ compatible = "amlogic,meson-gxbb-aobus-pinctrl";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
- uart_B: serial@84dc {
- compatible = "amlogic,meson-uart";
- reg = <0x0 0x84dc 0x0 0x14>;
- interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>;
- clocks = <&xtal>;
- status = "disabled";
+ gpio_ao: bank@14 {
+ reg = <0x0 0x00014 0x0 0x8>,
+ <0x0 0x0002c 0x0 0x4>,
+ <0x0 0x00024 0x0 0x8>;
+ reg-names = "mux", "pull", "gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ uart_ao_a_pins: uart_ao_a {
+ mux {
+ groups = "uart_tx_ao_a", "uart_rx_ao_a";
+ function = "uart_ao";
};
+ };
- pwm_ab: pwm@8550 {
- compatible = "amlogic,meson-gxbb-pwm";
- reg = <0x0 0x08550 0x0 0x10>;
- #pwm-cells = <3>;
- status = "disabled";
+ remote_input_ao_pins: remote_input_ao {
+ mux {
+ groups = "remote_input_ao";
+ function = "remote_input_ao";
};
+ };
- pwm_cd: pwm@8650 {
- compatible = "amlogic,meson-gxbb-pwm";
- reg = <0x0 0x08650 0x0 0x10>;
- #pwm-cells = <3>;
- status = "disabled";
+ i2c_ao_pins: i2c_ao {
+ mux {
+ groups = "i2c_sck_ao",
+ "i2c_sda_ao";
+ function = "i2c_ao";
};
+ };
- pwm_ef: pwm@86c0 {
- compatible = "amlogic,meson-gxbb-pwm";
- reg = <0x0 0x086c0 0x0 0x10>;
- #pwm-cells = <3>;
- status = "disabled";
+ pwm_ao_a_3_pins: pwm_ao_a_3 {
+ mux {
+ groups = "pwm_ao_a_3";
+ function = "pwm_ao_a_3";
};
+ };
- uart_C: serial@8700 {
- compatible = "amlogic,meson-uart";
- reg = <0x0 0x8700 0x0 0x14>;
- interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>;
- clocks = <&xtal>;
- status = "disabled";
+ pwm_ao_a_6_pins: pwm_ao_a_6 {
+ mux {
+ groups = "pwm_ao_a_6";
+ function = "pwm_ao_a_6";
};
+ };
- watchdog@98d0 {
- compatible = "amlogic,meson-gxbb-wdt";
- reg = <0x0 0x098d0 0x0 0x10>;
- clocks = <&xtal>;
+ pwm_ao_a_12_pins: pwm_ao_a_12 {
+ mux {
+ groups = "pwm_ao_a_12";
+ function = "pwm_ao_a_12";
};
+ };
- spifc: spi@8c80 {
- compatible = "amlogic,meson-gxbb-spifc";
- reg = <0x0 0x08c80 0x0 0x80>;
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&clkc CLKID_SPI>;
- status = "disabled";
+ pwm_ao_b_pins: pwm_ao_b {
+ mux {
+ groups = "pwm_ao_b";
+ function = "pwm_ao_b";
};
+ };
+ };
+
+ clkc_AO: clock-controller@040 {
+ compatible = "amlogic,gxbb-aoclkc";
+ reg = <0x0 0x00040 0x0 0x4>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ ir: ir@580 {
+ compatible = "amlogic,meson-gxbb-ir";
+ reg = <0x0 0x00580 0x0 0x40>;
+ interrupts = <GIC_SPI 196 IRQ_TYPE_EDGE_RISING>;
+ status = "disabled";
+ };
+
+ pwm_ab_AO: pwm@550 {
+ compatible = "amlogic,meson-gxbb-pwm";
+ reg = <0x0 0x0550 0x0 0x10>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ i2c_AO: i2c@500 {
+ compatible = "amlogic,meson-gxbb-i2c";
+ reg = <0x0 0x500 0x0 0x20>;
+ interrupts = <GIC_SPI 195 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc CLKID_AO_I2C>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+};
+
+&periphs {
+ rng {
+ compatible = "amlogic,meson-rng";
+ reg = <0x0 0x0 0x0 0x4>;
+ };
+
+ pinctrl_periphs: pinctrl@4b0 {
+ compatible = "amlogic,meson-gxbb-periphs-pinctrl";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ gpio: bank@4b0 {
+ reg = <0x0 0x004b0 0x0 0x28>,
+ <0x0 0x004e8 0x0 0x14>,
+ <0x0 0x00120 0x0 0x14>,
+ <0x0 0x00430 0x0 0x40>;
+ reg-names = "mux", "pull", "pull-enable", "gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
- i2c_A: i2c@8500 {
- compatible = "amlogic,meson-gxbb-i2c";
- reg = <0x0 0x08500 0x0 0x20>;
- interrupts = <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc CLKID_I2C>;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "disabled";
+ emmc_pins: emmc {
+ mux {
+ groups = "emmc_nand_d07",
+ "emmc_cmd",
+ "emmc_clk";
+ function = "emmc";
};
+ };
- i2c_B: i2c@87c0 {
- compatible = "amlogic,meson-gxbb-i2c";
- reg = <0x0 0x087c0 0x0 0x20>;
- interrupts = <GIC_SPI 214 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc CLKID_I2C>;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "disabled";
+ nor_pins: nor {
+ mux {
+ groups = "nor_d",
+ "nor_q",
+ "nor_c",
+ "nor_cs";
+ function = "nor";
};
+ };
- i2c_C: i2c@87e0 {
- compatible = "amlogic,meson-gxbb-i2c";
- reg = <0x0 0x087e0 0x0 0x20>;
- interrupts = <GIC_SPI 215 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc CLKID_I2C>;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "disabled";
+ sdcard_pins: sdcard {
+ mux {
+ groups = "sdcard_d0",
+ "sdcard_d1",
+ "sdcard_d2",
+ "sdcard_d3",
+ "sdcard_cmd",
+ "sdcard_clk";
+ function = "sdcard";
};
};
- gic: interrupt-controller@c4301000 {
- compatible = "arm,gic-400";
- reg = <0x0 0xc4301000 0 0x1000>,
- <0x0 0xc4302000 0 0x2000>,
- <0x0 0xc4304000 0 0x2000>,
- <0x0 0xc4306000 0 0x2000>;
- interrupt-controller;
- interrupts = <GIC_PPI 9
- (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
- #interrupt-cells = <3>;
- #address-cells = <0>;
- };
-
- aobus: aobus@c8100000 {
- compatible = "simple-bus";
- reg = <0x0 0xc8100000 0x0 0x100000>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges = <0x0 0x0 0x0 0xc8100000 0x0 0x100000>;
-
- pinctrl_aobus: pinctrl@14 {
- compatible = "amlogic,meson-gxbb-aobus-pinctrl";
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
-
- gpio_ao: bank@14 {
- reg = <0x0 0x00014 0x0 0x8>,
- <0x0 0x0002c 0x0 0x4>,
- <0x0 0x00024 0x0 0x8>;
- reg-names = "mux", "pull", "gpio";
- gpio-controller;
- #gpio-cells = <2>;
- };
-
- uart_ao_a_pins: uart_ao_a {
- mux {
- groups = "uart_tx_ao_a", "uart_rx_ao_a";
- function = "uart_ao";
- };
- };
-
- remote_input_ao_pins: remote_input_ao {
- mux {
- groups = "remote_input_ao";
- function = "remote_input_ao";
- };
- };
-
- i2c_ao_pins: i2c_ao {
- mux {
- groups = "i2c_sck_ao",
- "i2c_sda_ao";
- function = "i2c_ao";
- };
- };
-
- pwm_ao_a_3_pins: pwm_ao_a_3 {
- mux {
- groups = "pwm_ao_a_3";
- function = "pwm_ao_a_3";
- };
- };
-
- pwm_ao_a_6_pins: pwm_ao_a_6 {
- mux {
- groups = "pwm_ao_a_6";
- function = "pwm_ao_a_6";
- };
- };
-
- pwm_ao_a_12_pins: pwm_ao_a_12 {
- mux {
- groups = "pwm_ao_a_12";
- function = "pwm_ao_a_12";
- };
- };
-
- pwm_ao_b_pins: pwm_ao_b {
- mux {
- groups = "pwm_ao_b";
- function = "pwm_ao_b";
- };
- };
+ sdio_pins: sdio {
+ mux {
+ groups = "sdio_d0",
+ "sdio_d1",
+ "sdio_d2",
+ "sdio_d3",
+ "sdio_cmd",
+ "sdio_clk";
+ function = "sdio";
};
+ };
- clkc_AO: clock-controller@040 {
- compatible = "amlogic,gxbb-aoclkc";
- reg = <0x0 0x00040 0x0 0x4>;
- #clock-cells = <1>;
- #reset-cells = <1>;
+ sdio_irq_pins: sdio_irq {
+ mux {
+ groups = "sdio_irq";
+ function = "sdio";
};
+ };
- uart_AO: serial@4c0 {
- compatible = "amlogic,meson-uart";
- reg = <0x0 0x004c0 0x0 0x14>;
- interrupts = <GIC_SPI 193 IRQ_TYPE_EDGE_RISING>;
- clocks = <&xtal>;
- status = "disabled";
+ uart_a_pins: uart_a {
+ mux {
+ groups = "uart_tx_a",
+ "uart_rx_a";
+ function = "uart_a";
};
+ };
- ir: ir@580 {
- compatible = "amlogic,meson-gxbb-ir";
- reg = <0x0 0x00580 0x0 0x40>;
- interrupts = <GIC_SPI 196 IRQ_TYPE_EDGE_RISING>;
- status = "disabled";
+ uart_b_pins: uart_b {
+ mux {
+ groups = "uart_tx_b",
+ "uart_rx_b";
+ function = "uart_b";
};
+ };
- pwm_ab_AO: pwm@550 {
- compatible = "amlogic,meson-gxbb-pwm";
- reg = <0x0 0x0550 0x0 0x10>;
- #pwm-cells = <3>;
- status = "disabled";
+ uart_c_pins: uart_c {
+ mux {
+ groups = "uart_tx_c",
+ "uart_rx_c";
+ function = "uart_c";
};
+ };
- i2c_AO: i2c@500 {
- compatible = "amlogic,meson-gxbb-i2c";
- reg = <0x0 0x500 0x0 0x20>;
- interrupts = <GIC_SPI 195 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc CLKID_AO_I2C>;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "disabled";
+ i2c_a_pins: i2c_a {
+ mux {
+ groups = "i2c_sck_a",
+ "i2c_sda_a";
+ function = "i2c_a";
};
};
- periphs: periphs@c8834000 {
- compatible = "simple-bus";
- reg = <0x0 0xc8834000 0x0 0x2000>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges = <0x0 0x0 0x0 0xc8834000 0x0 0x2000>;
+ i2c_b_pins: i2c_b {
+ mux {
+ groups = "i2c_sck_b",
+ "i2c_sda_b";
+ function = "i2c_b";
+ };
+ };
- rng {
- compatible = "amlogic,meson-rng";
- reg = <0x0 0x0 0x0 0x4>;
+ i2c_c_pins: i2c_c {
+ mux {
+ groups = "i2c_sck_c",
+ "i2c_sda_c";
+ function = "i2c_c";
};
+ };
- pinctrl_periphs: pinctrl@4b0 {
- compatible = "amlogic,meson-gxbb-periphs-pinctrl";
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
-
- gpio: bank@4b0 {
- reg = <0x0 0x004b0 0x0 0x28>,
- <0x0 0x004e8 0x0 0x14>,
- <0x0 0x00120 0x0 0x14>,
- <0x0 0x00430 0x0 0x40>;
- reg-names = "mux", "pull", "pull-enable", "gpio";
- gpio-controller;
- #gpio-cells = <2>;
- };
-
- emmc_pins: emmc {
- mux {
- groups = "emmc_nand_d07",
- "emmc_cmd",
- "emmc_clk";
- function = "emmc";
- };
- };
-
- nor_pins: nor {
- mux {
- groups = "nor_d",
- "nor_q",
- "nor_c",
- "nor_cs";
- function = "nor";
- };
- };
-
- sdcard_pins: sdcard {
- mux {
- groups = "sdcard_d0",
- "sdcard_d1",
- "sdcard_d2",
- "sdcard_d3",
- "sdcard_cmd",
- "sdcard_clk";
- function = "sdcard";
- };
- };
-
- sdio_pins: sdio {
- mux {
- groups = "sdio_d0",
- "sdio_d1",
- "sdio_d2",
- "sdio_d3",
- "sdio_cmd",
- "sdio_clk";
- function = "sdio";
- };
- };
-
- sdio_irq_pins: sdio_irq {
- mux {
- groups = "sdio_irq";
- function = "sdio";
- };
- };
-
- uart_a_pins: uart_a {
- mux {
- groups = "uart_tx_a",
- "uart_rx_a";
- function = "uart_a";
- };
- };
-
- uart_b_pins: uart_b {
- mux {
- groups = "uart_tx_b",
- "uart_rx_b";
- function = "uart_b";
- };
- };
-
- uart_c_pins: uart_c {
- mux {
- groups = "uart_tx_c",
- "uart_rx_c";
- function = "uart_c";
- };
- };
-
- i2c_a_pins: i2c_a {
- mux {
- groups = "i2c_sck_a",
- "i2c_sda_a";
- function = "i2c_a";
- };
- };
-
- i2c_b_pins: i2c_b {
- mux {
- groups = "i2c_sck_b",
- "i2c_sda_b";
- function = "i2c_b";
- };
- };
-
- i2c_c_pins: i2c_c {
- mux {
- groups = "i2c_sck_c",
- "i2c_sda_c";
- function = "i2c_c";
- };
- };
-
- eth_pins: eth_c {
- mux {
- groups = "eth_mdio",
- "eth_mdc",
- "eth_clk_rx_clk",
- "eth_rx_dv",
- "eth_rxd0",
- "eth_rxd1",
- "eth_rxd2",
- "eth_rxd3",
- "eth_rgmii_tx_clk",
- "eth_tx_en",
- "eth_txd0",
- "eth_txd1",
- "eth_txd2",
- "eth_txd3";
- function = "eth";
- };
- };
-
- pwm_a_x_pins: pwm_a_x {
- mux {
- groups = "pwm_a_x";
- function = "pwm_a_x";
- };
- };
-
- pwm_a_y_pins: pwm_a_y {
- mux {
- groups = "pwm_a_y";
- function = "pwm_a_y";
- };
- };
-
- pwm_b_pins: pwm_b {
- mux {
- groups = "pwm_b";
- function = "pwm_b";
- };
- };
-
- pwm_d_pins: pwm_d {
- mux {
- groups = "pwm_d";
- function = "pwm_d";
- };
- };
-
- pwm_e_pins: pwm_e {
- mux {
- groups = "pwm_e";
- function = "pwm_e";
- };
- };
-
- pwm_f_x_pins: pwm_f_x {
- mux {
- groups = "pwm_f_x";
- function = "pwm_f_x";
- };
- };
-
- pwm_f_y_pins: pwm_f_y {
- mux {
- groups = "pwm_f_y";
- function = "pwm_f_y";
- };
- };
+ eth_pins: eth_c {
+ mux {
+ groups = "eth_mdio",
+ "eth_mdc",
+ "eth_clk_rx_clk",
+ "eth_rx_dv",
+ "eth_rxd0",
+ "eth_rxd1",
+ "eth_rxd2",
+ "eth_rxd3",
+ "eth_rgmii_tx_clk",
+ "eth_tx_en",
+ "eth_txd0",
+ "eth_txd1",
+ "eth_txd2",
+ "eth_txd3";
+ function = "eth";
};
};
- hiubus: hiubus@c883c000 {
- compatible = "simple-bus";
- reg = <0x0 0xc883c000 0x0 0x2000>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges = <0x0 0x0 0x0 0xc883c000 0x0 0x2000>;
+ pwm_a_x_pins: pwm_a_x {
+ mux {
+ groups = "pwm_a_x";
+ function = "pwm_a_x";
+ };
+ };
- clkc: clock-controller@0 {
- compatible = "amlogic,gxbb-clkc";
- #clock-cells = <1>;
- reg = <0x0 0x0 0x0 0x3db>;
+ pwm_a_y_pins: pwm_a_y {
+ mux {
+ groups = "pwm_a_y";
+ function = "pwm_a_y";
};
+ };
- mailbox: mailbox@404 {
- compatible = "amlogic,meson-gxbb-mhu";
- reg = <0 0x404 0 0x4c>;
- interrupts = <0 208 IRQ_TYPE_EDGE_RISING>,
- <0 209 IRQ_TYPE_EDGE_RISING>,
- <0 210 IRQ_TYPE_EDGE_RISING>;
- #mbox-cells = <1>;
+ pwm_b_pins: pwm_b {
+ mux {
+ groups = "pwm_b";
+ function = "pwm_b";
};
};
- apb: apb@d0000000 {
- compatible = "simple-bus";
- reg = <0x0 0xd0000000 0x0 0x200000>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges = <0x0 0x0 0x0 0xd0000000 0x0 0x200000>;
+ pwm_d_pins: pwm_d {
+ mux {
+ groups = "pwm_d";
+ function = "pwm_d";
+ };
};
- usb0: usb@c9000000 {
- compatible = "amlogic,meson-gxbb-usb", "snps,dwc2";
- reg = <0x0 0xc9000000 0x0 0x40000>;
- interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clkc CLKID_USB0_DDR_BRIDGE>;
- clock-names = "otg";
- phys = <&usb0_phy>;
- phy-names = "usb2-phy";
- dr_mode = "host";
- status = "disabled";
+ pwm_e_pins: pwm_e {
+ mux {
+ groups = "pwm_e";
+ function = "pwm_e";
+ };
};
- usb1: usb@c9100000 {
- compatible = "amlogic,meson-gxbb-usb", "snps,dwc2";
- reg = <0x0 0xc9100000 0x0 0x40000>;
- interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clkc CLKID_USB1_DDR_BRIDGE>;
- clock-names = "otg";
- phys = <&usb1_phy>;
- phy-names = "usb2-phy";
- dr_mode = "host";
- status = "disabled";
+ pwm_f_x_pins: pwm_f_x {
+ mux {
+ groups = "pwm_f_x";
+ function = "pwm_f_x";
+ };
};
- ethmac: ethernet@c9410000 {
- compatible = "amlogic,meson-gxbb-dwmac", "snps,dwmac";
- reg = <0x0 0xc9410000 0x0 0x10000
- 0x0 0xc8834540 0x0 0x4>;
- interrupts = <0 8 1>;
- interrupt-names = "macirq";
- clocks = <&clkc CLKID_ETH>,
- <&clkc CLKID_FCLK_DIV2>,
- <&clkc CLKID_MPLL2>;
- clock-names = "stmmaceth", "clkin0", "clkin1";
- phy-mode = "rgmii";
- status = "disabled";
+ pwm_f_y_pins: pwm_f_y {
+ mux {
+ groups = "pwm_f_y";
+ function = "pwm_f_y";
+ };
};
};
};
+
+&hiubus {
+ clkc: clock-controller@0 {
+ compatible = "amlogic,gxbb-clkc";
+ #clock-cells = <1>;
+ reg = <0x0 0x0 0x0 0x3db>;
+ };
+
+ mailbox: mailbox@404 {
+ compatible = "amlogic,meson-gxbb-mhu";
+ reg = <0 0x404 0 0x4c>;
+ interrupts = <0 208 IRQ_TYPE_EDGE_RISING>,
+ <0 209 IRQ_TYPE_EDGE_RISING>,
+ <0 210 IRQ_TYPE_EDGE_RISING>;
+ #mbox-cells = <1>;
+ };
+};
--
2.7.0
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH v2 2/3] ARM64: dts: amlogic: Add basic support for Amlogic S905X
2016-09-14 20:08 [PATCH v2 0/3] ARM64: amlogic: Add support for GXL SoC Family Neil Armstrong
2016-09-14 20:08 ` [PATCH v2 1/3] ARM64: dts: amlogic: Add Meson GX dtsi from GXBB Neil Armstrong
@ 2016-09-14 20:08 ` Neil Armstrong
2016-09-14 20:08 ` [PATCH v2 3/3] ARM64: dts: amlogic: Add basic support for Amlogic S905D Neil Armstrong
2 siblings, 0 replies; 4+ messages in thread
From: Neil Armstrong @ 2016-09-14 20:08 UTC (permalink / raw)
To: afaerber, khilman, carlo
Cc: Carlo Caione, devicetree, linux-kernel, linux-arm-kernel,
linux-amlogic, Neil Armstrong
From: Carlo Caione <carlo@endlessm.com>
This patch introduces the basic support for the Amlogic S905X (Meson
GXL) and for the Amlogic evaluation board P212.
No documentation has been released yet for this SoC, so for now only the
bare minimum has been added in the DT.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
Documentation/devicetree/bindings/arm/amlogic.txt | 7 +++
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../boot/dts/amlogic/meson-gxl-s905x-p212.dts | 69 ++++++++++++++++++++++
arch/arm64/boot/dts/amlogic/meson-gxl-s905x.dtsi | 48 +++++++++++++++
arch/arm64/boot/dts/amlogic/meson-gxl.dtsi | 48 +++++++++++++++
5 files changed, 173 insertions(+)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dts
create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905x.dtsi
create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt
index fcc6f6c..7edb635 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.txt
+++ b/Documentation/devicetree/bindings/arm/amlogic.txt
@@ -17,6 +17,10 @@ Boards with the Amlogic Meson GXBaby SoC shall have the following properties:
Required root node property:
compatible: "amlogic,meson-gxbb";
+Boards with the Amlogic Meson GXL S905X SoC shall have the following properties:
+ Required root node property:
+ compatible: "amlogic,s905x", "amlogic,meson-gxl";
+
Board compatible values:
- "geniatech,atv1200" (Meson6)
- "minix,neo-x8" (Meson8)
@@ -28,3 +32,6 @@ Board compatible values:
- "hardkernel,odroid-c2" (Meson gxbb)
- "amlogic,p200" (Meson gxbb)
- "amlogic,p201" (Meson gxbb)
+ - "amlogic,p212" (Meson gxl s905x)
+ - "amlogic,p230" (Meson gxl s905d)
+ - "amlogic,p231" (Meson gxl s905d)
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 47ec703..1f78b07 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -4,6 +4,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-p201.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-vega-s95-pro.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-vega-s95-meta.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-vega-s95-telos.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-p212.dtb
always := $(dtb-y)
subdir-y := $(dts-dirs)
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dts
new file mode 100644
index 0000000..9639f01
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dts
@@ -0,0 +1,69 @@
+/*
+ * Copyright (c) 2016 Endless Computers, Inc.
+ * Author: Carlo Caione <carlo@endlessm.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "meson-gxl-s905x.dtsi"
+
+/ {
+ compatible = "amlogic,p212", "amlogic,s905x", "amlogic,meson-gxl";
+ model = "Amlogic Meson GXL (S905X) P212 Development Board";
+
+ aliases {
+ serial0 = &uart_AO;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+};
+
+/* This UART is brought out to the DB9 connector */
+&uart_AO {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x.dtsi
new file mode 100644
index 0000000..07f0e0b
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x.dtsi
@@ -0,0 +1,48 @@
+/*
+ * Copyright (c) 2016 Endless Computers, Inc.
+ * Author: Carlo Caione <carlo@endlessm.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "meson-gxl.dtsi"
+
+/ {
+ compatible = "amlogic,s905x", "amlogic,meson-gxl";
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
new file mode 100644
index 0000000..13b10ee
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
@@ -0,0 +1,48 @@
+/*
+ * Copyright (c) 2016 Endless Computers, Inc.
+ * Author: Carlo Caione <carlo@endlessm.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "meson-gx.dtsi"
+
+/ {
+ compatible = "amlogic,meson-gxl";
+};
--
2.7.0
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH v2 3/3] ARM64: dts: amlogic: Add basic support for Amlogic S905D
2016-09-14 20:08 [PATCH v2 0/3] ARM64: amlogic: Add support for GXL SoC Family Neil Armstrong
2016-09-14 20:08 ` [PATCH v2 1/3] ARM64: dts: amlogic: Add Meson GX dtsi from GXBB Neil Armstrong
2016-09-14 20:08 ` [PATCH v2 2/3] ARM64: dts: amlogic: Add basic support for Amlogic S905X Neil Armstrong
@ 2016-09-14 20:08 ` Neil Armstrong
2 siblings, 0 replies; 4+ messages in thread
From: Neil Armstrong @ 2016-09-14 20:08 UTC (permalink / raw)
To: afaerber, khilman, carlo
Cc: Neil Armstrong, devicetree, linux-kernel, linux-arm-kernel,
linux-amlogic
This patch introduces the basic support for the Amlogic S905D (MesonGXL)
and for the Amlogic evaluation boards P230 and P231.
No documentation has been released yet for this SoC, so for now only the
bare minimum has been added in the DT.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
Documentation/devicetree/bindings/arm/amlogic.txt | 4 ++
arch/arm64/boot/dts/amlogic/Makefile | 2 +
.../boot/dts/amlogic/meson-gxl-s905d-p230.dts | 51 +++++++++++++++++
.../boot/dts/amlogic/meson-gxl-s905d-p231.dts | 51 +++++++++++++++++
.../boot/dts/amlogic/meson-gxl-s905d-p23x.dtsi | 64 ++++++++++++++++++++++
arch/arm64/boot/dts/amlogic/meson-gxl-s905d.dtsi | 48 ++++++++++++++++
6 files changed, 220 insertions(+)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts
create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p231.dts
create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p23x.dtsi
create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905d.dtsi
diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt
index 7edb635..fffc179 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.txt
+++ b/Documentation/devicetree/bindings/arm/amlogic.txt
@@ -21,6 +21,10 @@ Boards with the Amlogic Meson GXL S905X SoC shall have the following properties:
Required root node property:
compatible: "amlogic,s905x", "amlogic,meson-gxl";
+Boards with the Amlogic Meson GXL S905D SoC shall have the following properties:
+ Required root node property:
+ compatible: "amlogic,s905d", "amlogic,meson-gxl";
+
Board compatible values:
- "geniatech,atv1200" (Meson6)
- "minix,neo-x8" (Meson8)
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 1f78b07..57e0ae0 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -5,6 +5,8 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-vega-s95-pro.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-vega-s95-meta.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-vega-s95-telos.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-p212.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p230.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p231.dtb
always := $(dtb-y)
subdir-y := $(dts-dirs)
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts
new file mode 100644
index 0000000..3dfaa37
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts
@@ -0,0 +1,51 @@
+/*
+ * Copyright (c) 2016 Endless Computers, Inc.
+ * Author: Carlo Caione <carlo@endlessm.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "meson-gxl-s905d-p23x.dtsi"
+
+/ {
+ compatible = "amlogic,p230", "amlogic,s905d", "amlogic,meson-gxl";
+ model = "Amlogic Meson GXL (S905D) P230 Development Board";
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p231.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p231.dts
new file mode 100644
index 0000000..ade8d29
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p231.dts
@@ -0,0 +1,51 @@
+/*
+ * Copyright (c) 2016 Endless Computers, Inc.
+ * Author: Carlo Caione <carlo@endlessm.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "meson-gxl-s905d-p23x.dtsi"
+
+/ {
+ compatible = "amlogic,p231", "amlogic,s905d", "amlogic,meson-gxl";
+ model = "Amlogic Meson GXL (S905D) P231 Development Board";
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p23x.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p23x.dtsi
new file mode 100644
index 0000000..1602719
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p23x.dtsi
@@ -0,0 +1,64 @@
+/*
+ * Copyright (c) 2016 Endless Computers, Inc.
+ * Author: Carlo Caione <carlo@endlessm.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "meson-gxl-s905d.dtsi"
+
+/ {
+ aliases {
+ serial0 = &uart_AO;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+};
+
+&uart_AO {
+ status = "okay";
+};
+
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d.dtsi
new file mode 100644
index 0000000..615308e
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d.dtsi
@@ -0,0 +1,48 @@
+/*
+ * Copyright (c) 2016 Endless Computers, Inc.
+ * Author: Carlo Caione <carlo@endlessm.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "meson-gxl.dtsi"
+
+/ {
+ compatible = "amlogic,s905d", "amlogic,meson-gxl";
+};
--
2.7.0
^ permalink raw reply related [flat|nested] 4+ messages in thread
end of thread, other threads:[~2016-09-14 20:09 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-09-14 20:08 [PATCH v2 0/3] ARM64: amlogic: Add support for GXL SoC Family Neil Armstrong
2016-09-14 20:08 ` [PATCH v2 1/3] ARM64: dts: amlogic: Add Meson GX dtsi from GXBB Neil Armstrong
2016-09-14 20:08 ` [PATCH v2 2/3] ARM64: dts: amlogic: Add basic support for Amlogic S905X Neil Armstrong
2016-09-14 20:08 ` [PATCH v2 3/3] ARM64: dts: amlogic: Add basic support for Amlogic S905D Neil Armstrong
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).