From: Lee Jones <lee.jones@linaro.org>
To: Chen-Yu Tsai <wens@csie.org>
Cc: linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-sunxi@googlegroups.com
Subject: Re: [PATCH v2 1/2] mfd: axp20x: Add address extension registers for AXP806 regmap
Date: Fri, 9 Dec 2016 11:05:05 +0000 [thread overview]
Message-ID: <20161209110505.GK3625@dell.home> (raw)
In-Reply-To: <20161123031616.10114-2-wens@csie.org>
On Wed, 23 Nov 2016, Chen-Yu Tsai wrote:
> The AXP806 supports either master/standalone or slave mode.
> Slave mode allows sharing the serial bus, even with multiple
> AXP806 which all have the same hardware address.
>
> This is done with extra "serial interface address extension",
> or AXP806_BUS_ADDR_EXT, and "register address extension", or
> AXP806_REG_ADDR_EXT, registers. The former is read-only, with
> 1 bit customizable at the factory, and 1 bit depending on the
> state of an external pin. The latter is writable. Only when
> the these device addressing bits (in the upper 4 bits of the
> registers) match, will the device respond to operations on
> its other registers.
>
> Add these 2 registers to the regmap so we can access them.
>
> Signed-off-by: Chen-Yu Tsai <wens@csie.org>
> ---
> drivers/mfd/axp20x.c | 3 ++-
> include/linux/mfd/axp20x.h | 2 ++
> 2 files changed, 4 insertions(+), 1 deletion(-)
Applied for v4.11, thanks.
> diff --git a/drivers/mfd/axp20x.c b/drivers/mfd/axp20x.c
> index ba130be32e61..cdaeb34a9a38 100644
> --- a/drivers/mfd/axp20x.c
> +++ b/drivers/mfd/axp20x.c
> @@ -135,6 +135,7 @@ static const struct regmap_range axp806_writeable_ranges[] = {
> regmap_reg_range(AXP806_PWR_OUT_CTRL1, AXP806_CLDO3_V_CTRL),
> regmap_reg_range(AXP20X_IRQ1_EN, AXP20X_IRQ2_EN),
> regmap_reg_range(AXP20X_IRQ1_STATE, AXP20X_IRQ2_STATE),
> + regmap_reg_range(AXP806_REG_ADDR_EXT, AXP806_REG_ADDR_EXT),
> };
>
> static const struct regmap_range axp806_volatile_ranges[] = {
> @@ -305,7 +306,7 @@ static const struct regmap_config axp806_regmap_config = {
> .val_bits = 8,
> .wr_table = &axp806_writeable_table,
> .volatile_table = &axp806_volatile_table,
> - .max_register = AXP806_VREF_TEMP_WARN_L,
> + .max_register = AXP806_REG_ADDR_EXT,
> .cache_type = REGCACHE_RBTREE,
> };
>
> diff --git a/include/linux/mfd/axp20x.h b/include/linux/mfd/axp20x.h
> index fec597fb34cb..7e85ececcedf 100644
> --- a/include/linux/mfd/axp20x.h
> +++ b/include/linux/mfd/axp20x.h
> @@ -115,6 +115,8 @@ enum {
> #define AXP806_CLDO2_V_CTRL 0x25
> #define AXP806_CLDO3_V_CTRL 0x26
> #define AXP806_VREF_TEMP_WARN_L 0xf3
> +#define AXP806_BUS_ADDR_EXT 0xfe
> +#define AXP806_REG_ADDR_EXT 0xff
>
> /* Interrupt */
> #define AXP152_IRQ1_EN 0x40
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
next prev parent reply other threads:[~2016-12-09 11:01 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-11-23 3:16 [PATCH v2 0/2] mfd: axp20x: Fix AXP806 access errors on cold boot Chen-Yu Tsai
2016-11-23 3:16 ` [PATCH v2 1/2] mfd: axp20x: Add address extension registers for AXP806 regmap Chen-Yu Tsai
2016-12-09 11:05 ` Lee Jones [this message]
2016-11-23 3:16 ` [PATCH v2 2/2] mfd: axp20x: Fix AXP806 access errors on cold boot Chen-Yu Tsai
2016-12-09 11:20 ` Lee Jones
2016-12-13 16:47 ` Mark Brown
2016-12-14 13:52 ` Chen-Yu Tsai
2016-12-14 17:40 ` Mark Brown
2017-01-03 3:54 ` Chen-Yu Tsai
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20161209110505.GK3625@dell.home \
--to=lee.jones@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-sunxi@googlegroups.com \
--cc=wens@csie.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).