* [PATCH 1/3] NFC: trf7970a: add device tree option for 27MHz clock
@ 2016-12-15 22:30 Geoff Lansberry
2016-12-15 22:30 ` [PATCH 2/3] NFC: trf7970a: Add device tree option of 1.8 Volt IO voltage Geoff Lansberry
` (3 more replies)
0 siblings, 4 replies; 18+ messages in thread
From: Geoff Lansberry @ 2016-12-15 22:30 UTC (permalink / raw)
To: linux-wireless
Cc: lauro.venancio, aloisio.almeida, sameo, robh+dt, mark.rutland,
netdev, devicetree, linux-kernel, mgreer, justin,
Geoff Lansberry
From: Geoff Lansberry <geoff@kuvee.com>
---
.../devicetree/bindings/net/nfc/trf7970a.txt | 3 ++
drivers/nfc/trf7970a.c | 42 ++++++++++++++++------
2 files changed, 34 insertions(+), 11 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
index 32b35a0..9dda879 100644
--- a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
+++ b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
@@ -21,6 +21,8 @@ Optional SoC Specific Properties:
- t5t-rmb-extra-byte-quirk: Specify that the trf7970a has the erratum
where an extra byte is returned by Read Multiple Block commands issued
to Type 5 tags.
+- crystal_27mhz: Set to specify that the input frequency to the trf7970a is 27.12MHz
+
Example (for ARM-based BeagleBone with TRF7970A on SPI1):
@@ -43,6 +45,7 @@ Example (for ARM-based BeagleBone with TRF7970A on SPI1):
irq-status-read-quirk;
en2-rf-quirk;
t5t-rmb-extra-byte-quirk;
+ crystal_27mhz;
status = "okay";
};
};
diff --git a/drivers/nfc/trf7970a.c b/drivers/nfc/trf7970a.c
index 26c9dbb..2d2a077 100644
--- a/drivers/nfc/trf7970a.c
+++ b/drivers/nfc/trf7970a.c
@@ -1056,12 +1056,11 @@ static int trf7970a_init(struct trf7970a *trf)
trf->chip_status_ctrl &= ~TRF7970A_CHIP_STATUS_RF_ON;
- ret = trf7970a_write(trf, TRF7970A_MODULATOR_SYS_CLK_CTRL, 0);
+ ret = trf7970a_write(trf, TRF7970A_MODULATOR_SYS_CLK_CTRL,
+ trf->modulator_sys_clk_ctrl);
if (ret)
goto err_out;
- trf->modulator_sys_clk_ctrl = 0;
-
ret = trf7970a_write(trf, TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS,
TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLH_96 |
TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLL_32);
@@ -1181,27 +1180,37 @@ static int trf7970a_in_config_rf_tech(struct trf7970a *trf, int tech)
switch (tech) {
case NFC_DIGITAL_RF_TECH_106A:
trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_14443A_106;
- trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_OOK;
+ trf->modulator_sys_clk_ctrl =
+ (trf->modulator_sys_clk_ctrl & 0xF8) |
+ TRF7970A_MODULATOR_DEPTH_OOK;
trf->guard_time = TRF7970A_GUARD_TIME_NFCA;
break;
case NFC_DIGITAL_RF_TECH_106B:
trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_14443B_106;
- trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_ASK10;
+ trf->modulator_sys_clk_ctrl =
+ (trf->modulator_sys_clk_ctrl & 0xF8) |
+ TRF7970A_MODULATOR_DEPTH_ASK10;
trf->guard_time = TRF7970A_GUARD_TIME_NFCB;
break;
case NFC_DIGITAL_RF_TECH_212F:
trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_FELICA_212;
- trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_ASK10;
+ trf->modulator_sys_clk_ctrl =
+ (trf->modulator_sys_clk_ctrl & 0xF8) |
+ TRF7970A_MODULATOR_DEPTH_ASK10;
trf->guard_time = TRF7970A_GUARD_TIME_NFCF;
break;
case NFC_DIGITAL_RF_TECH_424F:
trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_FELICA_424;
- trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_ASK10;
+ trf->modulator_sys_clk_ctrl =
+ (trf->modulator_sys_clk_ctrl & 0xF8) |
+ TRF7970A_MODULATOR_DEPTH_ASK10;
trf->guard_time = TRF7970A_GUARD_TIME_NFCF;
break;
case NFC_DIGITAL_RF_TECH_ISO15693:
trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_15693_SGL_1OF4_2648;
- trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_OOK;
+ trf->modulator_sys_clk_ctrl =
+ (trf->modulator_sys_clk_ctrl & 0xF8) |
+ TRF7970A_MODULATOR_DEPTH_OOK;
trf->guard_time = TRF7970A_GUARD_TIME_15693;
break;
default:
@@ -1571,17 +1580,23 @@ static int trf7970a_tg_config_rf_tech(struct trf7970a *trf, int tech)
trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_NFC_NFC_CE_MODE |
TRF7970A_ISO_CTRL_NFC_CE |
TRF7970A_ISO_CTRL_NFC_CE_14443A;
- trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_OOK;
+ trf->modulator_sys_clk_ctrl =
+ (trf->modulator_sys_clk_ctrl & 0xF8) |
+ TRF7970A_MODULATOR_DEPTH_OOK;
break;
case NFC_DIGITAL_RF_TECH_212F:
trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_NFC_NFC_CE_MODE |
TRF7970A_ISO_CTRL_NFC_NFCF_212;
- trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_ASK10;
+ trf->modulator_sys_clk_ctrl =
+ (trf->modulator_sys_clk_ctrl & 0xF8) |
+ TRF7970A_MODULATOR_DEPTH_ASK10;
break;
case NFC_DIGITAL_RF_TECH_424F:
trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_NFC_NFC_CE_MODE |
TRF7970A_ISO_CTRL_NFC_NFCF_424;
- trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_ASK10;
+ trf->modulator_sys_clk_ctrl =
+ (trf->modulator_sys_clk_ctrl & 0xF8) |
+ TRF7970A_MODULATOR_DEPTH_ASK10;
break;
default:
dev_dbg(trf->dev, "Unsupported rf technology: %d\n", tech);
@@ -2043,6 +2058,11 @@ static int trf7970a_probe(struct spi_device *spi)
return ret;
}
+ if (of_property_read_bool(np, "crystal_27mhz")) {
+ trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_27MHZ;
+ dev_dbg(trf->dev, "trf7970a configure crystal_27mhz\n");
+ }
+
if (of_property_read_bool(np, "en2-rf-quirk"))
trf->quirks |= TRF7970A_QUIRK_EN2_MUST_STAY_LOW;
--
Signed-off-by: Geoff Lansberry <geoff@kuvee.com>
^ permalink raw reply related [flat|nested] 18+ messages in thread* [PATCH 2/3] NFC: trf7970a: Add device tree option of 1.8 Volt IO voltage
2016-12-15 22:30 [PATCH 1/3] NFC: trf7970a: add device tree option for 27MHz clock Geoff Lansberry
@ 2016-12-15 22:30 ` Geoff Lansberry
2016-12-16 1:13 ` Mark Greer
2016-12-19 22:35 ` Rob Herring
2016-12-15 22:30 ` [PATCH 3/3] nfc: trf7970a: Prevent repeated polling from crashing the kernel Geoff Lansberry
` (2 subsequent siblings)
3 siblings, 2 replies; 18+ messages in thread
From: Geoff Lansberry @ 2016-12-15 22:30 UTC (permalink / raw)
To: linux-wireless
Cc: lauro.venancio, aloisio.almeida, sameo, robh+dt, mark.rutland,
netdev, devicetree, linux-kernel, mgreer, justin,
Geoff Lansberry
From: Geoff Lansberry <geoff@kuvee.com>
---
Documentation/devicetree/bindings/net/nfc/trf7970a.txt | 2 ++
drivers/nfc/trf7970a.c | 13 ++++++++++++-
2 files changed, 14 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
index 9dda879..208f045 100644
--- a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
+++ b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
@@ -21,6 +21,7 @@ Optional SoC Specific Properties:
- t5t-rmb-extra-byte-quirk: Specify that the trf7970a has the erratum
where an extra byte is returned by Read Multiple Block commands issued
to Type 5 tags.
+- vdd_io_1v8: Set to specify that the trf7970a io voltage should be set to 1.8V
- crystal_27mhz: Set to specify that the input frequency to the trf7970a is 27.12MHz
@@ -45,6 +46,7 @@ Example (for ARM-based BeagleBone with TRF7970A on SPI1):
irq-status-read-quirk;
en2-rf-quirk;
t5t-rmb-extra-byte-quirk;
+ vdd_io_1v8;
crystal_27mhz;
status = "okay";
};
diff --git a/drivers/nfc/trf7970a.c b/drivers/nfc/trf7970a.c
index 2d2a077..b4c37ab 100644
--- a/drivers/nfc/trf7970a.c
+++ b/drivers/nfc/trf7970a.c
@@ -441,6 +441,7 @@ struct trf7970a {
u8 iso_ctrl_tech;
u8 modulator_sys_clk_ctrl;
u8 special_fcn_reg1;
+ u8 io_ctrl;
unsigned int guard_time;
int technology;
int framing;
@@ -1048,6 +1049,11 @@ static int trf7970a_init(struct trf7970a *trf)
if (ret)
goto err_out;
+ ret = trf7970a_write(trf, TRF7970A_REG_IO_CTRL,
+ trf->io_ctrl|TRF7970A_REG_IO_CTRL_VRS(0x1));
+ if (ret)
+ goto err_out;
+
ret = trf7970a_write(trf, TRF7970A_NFC_TARGET_LEVEL, 0);
if (ret)
goto err_out;
@@ -1764,7 +1770,7 @@ static int _trf7970a_tg_listen(struct nfc_digital_dev *ddev, u16 timeout,
goto out_err;
ret = trf7970a_write(trf, TRF7970A_REG_IO_CTRL,
- TRF7970A_REG_IO_CTRL_VRS(0x1));
+ trf->io_ctrl|TRF7970A_REG_IO_CTRL_VRS(0x1));
if (ret)
goto out_err;
@@ -2058,6 +2064,11 @@ static int trf7970a_probe(struct spi_device *spi)
return ret;
}
+ if (of_property_read_bool(np, "vdd_io_1v8")) {
+ trf->io_ctrl = TRF7970A_REG_IO_CTRL_IO_LOW;
+ dev_dbg(trf->dev, "trf7970a config vdd_io_1v8\n");
+ }
+
if (of_property_read_bool(np, "crystal_27mhz")) {
trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_27MHZ;
dev_dbg(trf->dev, "trf7970a configure crystal_27mhz\n");
--
Signed-off-by: Geoff Lansberry <geoff@kuvee.com>
^ permalink raw reply related [flat|nested] 18+ messages in thread* Re: [PATCH 2/3] NFC: trf7970a: Add device tree option of 1.8 Volt IO voltage
2016-12-15 22:30 ` [PATCH 2/3] NFC: trf7970a: Add device tree option of 1.8 Volt IO voltage Geoff Lansberry
@ 2016-12-16 1:13 ` Mark Greer
2016-12-19 22:35 ` Rob Herring
1 sibling, 0 replies; 18+ messages in thread
From: Mark Greer @ 2016-12-16 1:13 UTC (permalink / raw)
To: Geoff Lansberry
Cc: linux-wireless, lauro.venancio, aloisio.almeida, sameo, robh+dt,
mark.rutland, netdev, devicetree, linux-kernel, justin
On Thu, Dec 15, 2016 at 05:30:43PM -0500, Geoff Lansberry wrote:
> From: Geoff Lansberry <geoff@kuvee.com>
Missing commit description.
> diff --git a/drivers/nfc/trf7970a.c b/drivers/nfc/trf7970a.c
> index 2d2a077..b4c37ab 100644
> --- a/drivers/nfc/trf7970a.c
> +++ b/drivers/nfc/trf7970a.c
> @@ -1048,6 +1049,11 @@ static int trf7970a_init(struct trf7970a *trf)
> if (ret)
> goto err_out;
>
> + ret = trf7970a_write(trf, TRF7970A_REG_IO_CTRL,
> + trf->io_ctrl|TRF7970A_REG_IO_CTRL_VRS(0x1));
s/l|T/l | T/
Otherwise, looks good.
Mark
--
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 2/3] NFC: trf7970a: Add device tree option of 1.8 Volt IO voltage
2016-12-15 22:30 ` [PATCH 2/3] NFC: trf7970a: Add device tree option of 1.8 Volt IO voltage Geoff Lansberry
2016-12-16 1:13 ` Mark Greer
@ 2016-12-19 22:35 ` Rob Herring
2016-12-20 16:13 ` Geoff Lansberry
1 sibling, 1 reply; 18+ messages in thread
From: Rob Herring @ 2016-12-19 22:35 UTC (permalink / raw)
To: Geoff Lansberry
Cc: linux-wireless, lauro.venancio, aloisio.almeida, sameo,
mark.rutland, netdev, devicetree, linux-kernel, mgreer, justin
On Thu, Dec 15, 2016 at 05:30:43PM -0500, Geoff Lansberry wrote:
> From: Geoff Lansberry <geoff@kuvee.com>
>
> ---
> Documentation/devicetree/bindings/net/nfc/trf7970a.txt | 2 ++
> drivers/nfc/trf7970a.c | 13 ++++++++++++-
> 2 files changed, 14 insertions(+), 1 deletion(-)
>
> diff --git a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
> index 9dda879..208f045 100644
> --- a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
> +++ b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
> @@ -21,6 +21,7 @@ Optional SoC Specific Properties:
> - t5t-rmb-extra-byte-quirk: Specify that the trf7970a has the erratum
> where an extra byte is returned by Read Multiple Block commands issued
> to Type 5 tags.
> +- vdd_io_1v8: Set to specify that the trf7970a io voltage should be set to 1.8V
Use the regulator binding and provide a fixed 1.8V supply.
> - crystal_27mhz: Set to specify that the input frequency to the trf7970a is 27.12MHz
>
>
> @@ -45,6 +46,7 @@ Example (for ARM-based BeagleBone with TRF7970A on SPI1):
> irq-status-read-quirk;
> en2-rf-quirk;
> t5t-rmb-extra-byte-quirk;
> + vdd_io_1v8;
> crystal_27mhz;
> status = "okay";
> };
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 2/3] NFC: trf7970a: Add device tree option of 1.8 Volt IO voltage
2016-12-19 22:35 ` Rob Herring
@ 2016-12-20 16:13 ` Geoff Lansberry
2016-12-21 2:07 ` Mark Greer
0 siblings, 1 reply; 18+ messages in thread
From: Geoff Lansberry @ 2016-12-20 16:13 UTC (permalink / raw)
To: Rob Herring
Cc: linux-wireless, Lauro Ramos Venancio, Aloisio Almeida Jr,
Samuel Ortiz, mark.rutland, netdev, devicetree, linux-kernel,
Mark Greer, Justin Bronder
On Mon, Dec 19, 2016 at 5:35 PM, Rob Herring <robh@kernel.org> wrote:
> On Thu, Dec 15, 2016 at 05:30:43PM -0500, Geoff Lansberry wrote:
>> From: Geoff Lansberry <geoff@kuvee.com>
>>
>> ---
>> Documentation/devicetree/bindings/net/nfc/trf7970a.txt | 2 ++
>> drivers/nfc/trf7970a.c | 13 ++++++++++++-
>> 2 files changed, 14 insertions(+), 1 deletion(-)
>>
>> diff --git a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
>> index 9dda879..208f045 100644
>> --- a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
>> +++ b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
>> @@ -21,6 +21,7 @@ Optional SoC Specific Properties:
>> - t5t-rmb-extra-byte-quirk: Specify that the trf7970a has the erratum
>> where an extra byte is returned by Read Multiple Block commands issued
>> to Type 5 tags.
>> +- vdd_io_1v8: Set to specify that the trf7970a io voltage should be set to 1.8V
>
> Use the regulator binding and provide a fixed 1.8V supply.
>
>> - crystal_27mhz: Set to specify that the input frequency to the trf7970a is 27.12MHz
>>
>>
>> @@ -45,6 +46,7 @@ Example (for ARM-based BeagleBone with TRF7970A on SPI1):
>> irq-status-read-quirk;
>> en2-rf-quirk;
>> t5t-rmb-extra-byte-quirk;
>> + vdd_io_1v8;
>> crystal_27mhz;
>> status = "okay";
>> };
Rob - using the regulator binding is new to me, but I've given it a
shot and just sent you another set of patches for your inspection.
Please let me know if this is what you had in mind.
Geoff
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 2/3] NFC: trf7970a: Add device tree option of 1.8 Volt IO voltage
2016-12-20 16:13 ` Geoff Lansberry
@ 2016-12-21 2:07 ` Mark Greer
0 siblings, 0 replies; 18+ messages in thread
From: Mark Greer @ 2016-12-21 2:07 UTC (permalink / raw)
To: Geoff Lansberry
Cc: Rob Herring, linux-wireless, Lauro Ramos Venancio,
Aloisio Almeida Jr, Samuel Ortiz, mark.rutland, netdev,
devicetree, linux-kernel, Justin Bronder
On Tue, Dec 20, 2016 at 11:13:23AM -0500, Geoff Lansberry wrote:
> On Mon, Dec 19, 2016 at 5:35 PM, Rob Herring <robh@kernel.org> wrote:
> > On Thu, Dec 15, 2016 at 05:30:43PM -0500, Geoff Lansberry wrote:
> >> From: Geoff Lansberry <geoff@kuvee.com>
> >>
> >> ---
> >> Documentation/devicetree/bindings/net/nfc/trf7970a.txt | 2 ++
> >> drivers/nfc/trf7970a.c | 13 ++++++++++++-
> >> 2 files changed, 14 insertions(+), 1 deletion(-)
> >>
> >> diff --git a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
> >> index 9dda879..208f045 100644
> >> --- a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
> >> +++ b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
> >> @@ -21,6 +21,7 @@ Optional SoC Specific Properties:
> >> - t5t-rmb-extra-byte-quirk: Specify that the trf7970a has the erratum
> >> where an extra byte is returned by Read Multiple Block commands issued
> >> to Type 5 tags.
> >> +- vdd_io_1v8: Set to specify that the trf7970a io voltage should be set to 1.8V
> >
> > Use the regulator binding and provide a fixed 1.8V supply.
> >
> >> - crystal_27mhz: Set to specify that the input frequency to the trf7970a is 27.12MHz
> >>
> >>
> >> @@ -45,6 +46,7 @@ Example (for ARM-based BeagleBone with TRF7970A on SPI1):
> >> irq-status-read-quirk;
> >> en2-rf-quirk;
> >> t5t-rmb-extra-byte-quirk;
> >> + vdd_io_1v8;
> >> crystal_27mhz;
> >> status = "okay";
> >> };
>
> Rob - using the regulator binding is new to me, but I've given it a
> shot and just sent you another set of patches for your inspection.
> Please let me know if this is what you had in mind.
This is my bad. Geoff followed my example and did something similar to
'vin-voltage-override' which shouldn't have been there in the first place.
I have this fixed (I think) locally and will submit once it I'm back from
my holiday travels.
Mark
--
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH 3/3] nfc: trf7970a: Prevent repeated polling from crashing the kernel
2016-12-15 22:30 [PATCH 1/3] NFC: trf7970a: add device tree option for 27MHz clock Geoff Lansberry
2016-12-15 22:30 ` [PATCH 2/3] NFC: trf7970a: Add device tree option of 1.8 Volt IO voltage Geoff Lansberry
@ 2016-12-15 22:30 ` Geoff Lansberry
2016-12-16 1:18 ` Mark Greer
2016-12-16 1:06 ` [PATCH 1/3] NFC: trf7970a: add device tree option for 27MHz clock Mark Greer
2016-12-19 22:31 ` Rob Herring
3 siblings, 1 reply; 18+ messages in thread
From: Geoff Lansberry @ 2016-12-15 22:30 UTC (permalink / raw)
To: linux-wireless
Cc: lauro.venancio, aloisio.almeida, sameo, robh+dt, mark.rutland,
netdev, devicetree, linux-kernel, mgreer, justin, Jaret Cantu,
Geoff Lansberry
From: Jaret Cantu <jaret.cantu@timesys.com>
Repeated polling attempts cause a NULL dereference error to occur.
This is because the curent state of the trf7970a is reading but
a request has been made to send a command.
The solution is to properly kill the waiting reading (workqueue)
before failing on the send.
---
drivers/nfc/trf7970a.c | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/drivers/nfc/trf7970a.c b/drivers/nfc/trf7970a.c
index b4c37ab..f96a321 100644
--- a/drivers/nfc/trf7970a.c
+++ b/drivers/nfc/trf7970a.c
@@ -1493,6 +1493,10 @@ static int trf7970a_send_cmd(struct nfc_digital_dev *ddev,
(trf->state != TRF7970A_ST_IDLE_RX_BLOCKED)) {
dev_err(trf->dev, "%s - Bogus state: %d\n", __func__,
trf->state);
+ if (trf->state == TRF7970A_ST_WAIT_FOR_RX_DATA ||
+ trf->state == TRF7970A_ST_WAIT_FOR_RX_DATA_CONT)
+ trf->ignore_timeout =
+ !cancel_delayed_work(&trf->timeout_work);
ret = -EIO;
goto out_err;
}
--
Signed-off-by: Geoff Lansberry <geoff@kuvee.com>
^ permalink raw reply related [flat|nested] 18+ messages in thread* Re: [PATCH 3/3] nfc: trf7970a: Prevent repeated polling from crashing the kernel
2016-12-15 22:30 ` [PATCH 3/3] nfc: trf7970a: Prevent repeated polling from crashing the kernel Geoff Lansberry
@ 2016-12-16 1:18 ` Mark Greer
0 siblings, 0 replies; 18+ messages in thread
From: Mark Greer @ 2016-12-16 1:18 UTC (permalink / raw)
To: Geoff Lansberry
Cc: linux-wireless, lauro.venancio, aloisio.almeida, sameo, robh+dt,
mark.rutland, netdev, devicetree, linux-kernel, justin,
Jaret Cantu
On Thu, Dec 15, 2016 at 05:30:44PM -0500, Geoff Lansberry wrote:
> From: Jaret Cantu <jaret.cantu@timesys.com>
>
> Repeated polling attempts cause a NULL dereference error to occur.
> This is because the curent state of the trf7970a is reading but
> a request has been made to send a command.
>
> The solution is to properly kill the waiting reading (workqueue)
> before failing on the send.
Maybe its just me but I find this description a little hard to grok.
Mind reworking it?
The patch itself looks fine.
Thanks,
Mark
--
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 1/3] NFC: trf7970a: add device tree option for 27MHz clock
2016-12-15 22:30 [PATCH 1/3] NFC: trf7970a: add device tree option for 27MHz clock Geoff Lansberry
2016-12-15 22:30 ` [PATCH 2/3] NFC: trf7970a: Add device tree option of 1.8 Volt IO voltage Geoff Lansberry
2016-12-15 22:30 ` [PATCH 3/3] nfc: trf7970a: Prevent repeated polling from crashing the kernel Geoff Lansberry
@ 2016-12-16 1:06 ` Mark Greer
2016-12-19 22:31 ` Rob Herring
3 siblings, 0 replies; 18+ messages in thread
From: Mark Greer @ 2016-12-16 1:06 UTC (permalink / raw)
To: Geoff Lansberry
Cc: linux-wireless, lauro.venancio, aloisio.almeida, sameo, robh+dt,
mark.rutland, netdev, devicetree, linux-kernel, justin
Hi Geoff.
On Thu, Dec 15, 2016 at 05:30:42PM -0500, Geoff Lansberry wrote:
> From: Geoff Lansberry <geoff@kuvee.com>
Please add an informative commit description to all of your commits.
No matter how trivial this patch may seem to you now, it may not be
to others (or to you in a few years).
> diff --git a/drivers/nfc/trf7970a.c b/drivers/nfc/trf7970a.c
> index 26c9dbb..2d2a077 100644
> --- a/drivers/nfc/trf7970a.c
> +++ b/drivers/nfc/trf7970a.c
> @@ -1181,27 +1180,37 @@ static int trf7970a_in_config_rf_tech(struct trf7970a *trf, int tech)
> switch (tech) {
> case NFC_DIGITAL_RF_TECH_106A:
> trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_14443A_106;
> - trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_OOK;
> + trf->modulator_sys_clk_ctrl =
> + (trf->modulator_sys_clk_ctrl & 0xF8) |
nit: s/0xF8/0xf8/ please (for consistency with the rest of the file.).
Otherwise, it looks good.
Thanks,
Mark
^ permalink raw reply [flat|nested] 18+ messages in thread* Re: [PATCH 1/3] NFC: trf7970a: add device tree option for 27MHz clock
2016-12-15 22:30 [PATCH 1/3] NFC: trf7970a: add device tree option for 27MHz clock Geoff Lansberry
` (2 preceding siblings ...)
2016-12-16 1:06 ` [PATCH 1/3] NFC: trf7970a: add device tree option for 27MHz clock Mark Greer
@ 2016-12-19 22:31 ` Rob Herring
2016-12-19 23:23 ` Geoff Lansberry
3 siblings, 1 reply; 18+ messages in thread
From: Rob Herring @ 2016-12-19 22:31 UTC (permalink / raw)
To: Geoff Lansberry
Cc: linux-wireless, lauro.venancio, aloisio.almeida, sameo,
mark.rutland, netdev, devicetree, linux-kernel, mgreer, justin
On Thu, Dec 15, 2016 at 05:30:42PM -0500, Geoff Lansberry wrote:
> From: Geoff Lansberry <geoff@kuvee.com>
>
> ---
> .../devicetree/bindings/net/nfc/trf7970a.txt | 3 ++
> drivers/nfc/trf7970a.c | 42 ++++++++++++++++------
> 2 files changed, 34 insertions(+), 11 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
> index 32b35a0..9dda879 100644
> --- a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
> +++ b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
> @@ -21,6 +21,8 @@ Optional SoC Specific Properties:
> - t5t-rmb-extra-byte-quirk: Specify that the trf7970a has the erratum
> where an extra byte is returned by Read Multiple Block commands issued
> to Type 5 tags.
> +- crystal_27mhz: Set to specify that the input frequency to the trf7970a is 27.12MHz
> +
Can't you use 'clock-frequency = "27000000";'?
>
> Example (for ARM-based BeagleBone with TRF7970A on SPI1):
>
> @@ -43,6 +45,7 @@ Example (for ARM-based BeagleBone with TRF7970A on SPI1):
> irq-status-read-quirk;
> en2-rf-quirk;
> t5t-rmb-extra-byte-quirk;
> + crystal_27mhz;
> status = "okay";
> };
> };
^ permalink raw reply [flat|nested] 18+ messages in thread* Re: [PATCH 1/3] NFC: trf7970a: add device tree option for 27MHz clock
2016-12-19 22:31 ` Rob Herring
@ 2016-12-19 23:23 ` Geoff Lansberry
2016-12-22 18:48 ` Rob Herring
0 siblings, 1 reply; 18+ messages in thread
From: Geoff Lansberry @ 2016-12-19 23:23 UTC (permalink / raw)
To: Rob Herring
Cc: linux-wireless, Lauro Ramos Venancio, Aloisio Almeida Jr,
Samuel Ortiz, mark.rutland, netdev, devicetree, linux-kernel,
Mark Greer, Justin Bronder
I can make that change, however, I worry that it may be a bit
misleading, since there are only two supported clock frequencies, but
a number like that to me implies that it could be set to any number
you want. I'm new at this, and so I'll go ahead and change it as you
request, but I'd like to hear your thoughts on my concern.
Thanks
Geoff
Geoff Lansberry
Engineering Guy
Kuvée, Inc
125 Kingston St., 3rd Floor
Boston, MA 02111
1-617-290-1118 (m)
geoff.lansberry (skype)
http://www.kuvee.com
On Mon, Dec 19, 2016 at 5:31 PM, Rob Herring <robh@kernel.org> wrote:
> On Thu, Dec 15, 2016 at 05:30:42PM -0500, Geoff Lansberry wrote:
>> From: Geoff Lansberry <geoff@kuvee.com>
>>
>> ---
>> .../devicetree/bindings/net/nfc/trf7970a.txt | 3 ++
>> drivers/nfc/trf7970a.c | 42 ++++++++++++++++------
>> 2 files changed, 34 insertions(+), 11 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
>> index 32b35a0..9dda879 100644
>> --- a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
>> +++ b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
>> @@ -21,6 +21,8 @@ Optional SoC Specific Properties:
>> - t5t-rmb-extra-byte-quirk: Specify that the trf7970a has the erratum
>> where an extra byte is returned by Read Multiple Block commands issued
>> to Type 5 tags.
>> +- crystal_27mhz: Set to specify that the input frequency to the trf7970a is 27.12MHz
>> +
>
> Can't you use 'clock-frequency = "27000000";'?
>
>>
>> Example (for ARM-based BeagleBone with TRF7970A on SPI1):
>>
>> @@ -43,6 +45,7 @@ Example (for ARM-based BeagleBone with TRF7970A on SPI1):
>> irq-status-read-quirk;
>> en2-rf-quirk;
>> t5t-rmb-extra-byte-quirk;
>> + crystal_27mhz;
>> status = "okay";
>> };
>> };
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 1/3] NFC: trf7970a: add device tree option for 27MHz clock
2016-12-19 23:23 ` Geoff Lansberry
@ 2016-12-22 18:48 ` Rob Herring
0 siblings, 0 replies; 18+ messages in thread
From: Rob Herring @ 2016-12-22 18:48 UTC (permalink / raw)
To: Geoff Lansberry
Cc: linux-wireless, Lauro Ramos Venancio, Aloisio Almeida Jr,
Samuel Ortiz, Mark Rutland, netdev, devicetree, linux-kernel,
Mark Greer, Justin Bronder
On Mon, Dec 19, 2016 at 5:23 PM, Geoff Lansberry <geoff@kuvee.com> wrote:
> I can make that change, however, I worry that it may be a bit
> misleading, since there are only two supported clock frequencies, but
> a number like that to me implies that it could be set to any number
> you want. I'm new at this, and so I'll go ahead and change it as you
> request, but I'd like to hear your thoughts on my concern.
Then the binding doc just needs to state what are the 2 valid frequencies.
Rob
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH 1/3] NFC: trf7970a: add device tree option for 27MHz clock
@ 2016-12-20 16:10 Geoff Lansberry
0 siblings, 0 replies; 18+ messages in thread
From: Geoff Lansberry @ 2016-12-20 16:10 UTC (permalink / raw)
To: linux-wireless
Cc: lauro.venancio, aloisio.almeida, sameo, robh+dt, mark.rutland,
netdev, devicetree, linux-kernel, mgreer, justin,
Geoff Lansberry
From: Geoff Lansberry <geoff@kuvee.com>
The TRF7970A has configuration options to support hardware designs
which use a 27.12MHz clock. This commit adds a device tree option
'clock-frequency' to support configuring the this chip for default
13.56MHz clock or the optional 27.12MHz clock.
---
.../devicetree/bindings/net/nfc/trf7970a.txt | 4 ++
drivers/nfc/trf7970a.c | 50 +++++++++++++++++-----
2 files changed, 43 insertions(+), 11 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
index 32b35a0..e262ac1 100644
--- a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
+++ b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
@@ -21,6 +21,8 @@ Optional SoC Specific Properties:
- t5t-rmb-extra-byte-quirk: Specify that the trf7970a has the erratum
where an extra byte is returned by Read Multiple Block commands issued
to Type 5 tags.
+- clock-frequency: Set to specify that the input frequency to the trf7970a is 13560000Hz or 27120000Hz
+
Example (for ARM-based BeagleBone with TRF7970A on SPI1):
@@ -43,6 +45,8 @@ Example (for ARM-based BeagleBone with TRF7970A on SPI1):
irq-status-read-quirk;
en2-rf-quirk;
t5t-rmb-extra-byte-quirk;
+ vdd_io_1v8;
+ clock-frequency = <27120000>;
status = "okay";
};
};
diff --git a/drivers/nfc/trf7970a.c b/drivers/nfc/trf7970a.c
index 26c9dbb..4e051e9 100644
--- a/drivers/nfc/trf7970a.c
+++ b/drivers/nfc/trf7970a.c
@@ -124,6 +124,9 @@
NFC_PROTO_ISO15693_MASK | NFC_PROTO_NFC_DEP_MASK)
#define TRF7970A_AUTOSUSPEND_DELAY 30000 /* 30 seconds */
+#define TRF7970A_13MHZ_CLOCK_FREQUENCY 13560000
+#define TRF7970A_27MHZ_CLOCK_FREQUENCY 27120000
+
#define TRF7970A_RX_SKB_ALLOC_SIZE 256
@@ -1056,12 +1059,11 @@ static int trf7970a_init(struct trf7970a *trf)
trf->chip_status_ctrl &= ~TRF7970A_CHIP_STATUS_RF_ON;
- ret = trf7970a_write(trf, TRF7970A_MODULATOR_SYS_CLK_CTRL, 0);
+ ret = trf7970a_write(trf, TRF7970A_MODULATOR_SYS_CLK_CTRL,
+ trf->modulator_sys_clk_ctrl);
if (ret)
goto err_out;
- trf->modulator_sys_clk_ctrl = 0;
-
ret = trf7970a_write(trf, TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS,
TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLH_96 |
TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLL_32);
@@ -1181,27 +1183,37 @@ static int trf7970a_in_config_rf_tech(struct trf7970a *trf, int tech)
switch (tech) {
case NFC_DIGITAL_RF_TECH_106A:
trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_14443A_106;
- trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_OOK;
+ trf->modulator_sys_clk_ctrl =
+ (trf->modulator_sys_clk_ctrl & 0xF8) |
+ TRF7970A_MODULATOR_DEPTH_OOK;
trf->guard_time = TRF7970A_GUARD_TIME_NFCA;
break;
case NFC_DIGITAL_RF_TECH_106B:
trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_14443B_106;
- trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_ASK10;
+ trf->modulator_sys_clk_ctrl =
+ (trf->modulator_sys_clk_ctrl & 0xF8) |
+ TRF7970A_MODULATOR_DEPTH_ASK10;
trf->guard_time = TRF7970A_GUARD_TIME_NFCB;
break;
case NFC_DIGITAL_RF_TECH_212F:
trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_FELICA_212;
- trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_ASK10;
+ trf->modulator_sys_clk_ctrl =
+ (trf->modulator_sys_clk_ctrl & 0xF8) |
+ TRF7970A_MODULATOR_DEPTH_ASK10;
trf->guard_time = TRF7970A_GUARD_TIME_NFCF;
break;
case NFC_DIGITAL_RF_TECH_424F:
trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_FELICA_424;
- trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_ASK10;
+ trf->modulator_sys_clk_ctrl =
+ (trf->modulator_sys_clk_ctrl & 0xF8) |
+ TRF7970A_MODULATOR_DEPTH_ASK10;
trf->guard_time = TRF7970A_GUARD_TIME_NFCF;
break;
case NFC_DIGITAL_RF_TECH_ISO15693:
trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_15693_SGL_1OF4_2648;
- trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_OOK;
+ trf->modulator_sys_clk_ctrl =
+ (trf->modulator_sys_clk_ctrl & 0xF8) |
+ TRF7970A_MODULATOR_DEPTH_OOK;
trf->guard_time = TRF7970A_GUARD_TIME_15693;
break;
default:
@@ -1571,17 +1583,23 @@ static int trf7970a_tg_config_rf_tech(struct trf7970a *trf, int tech)
trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_NFC_NFC_CE_MODE |
TRF7970A_ISO_CTRL_NFC_CE |
TRF7970A_ISO_CTRL_NFC_CE_14443A;
- trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_OOK;
+ trf->modulator_sys_clk_ctrl =
+ (trf->modulator_sys_clk_ctrl & 0xF8) |
+ TRF7970A_MODULATOR_DEPTH_OOK;
break;
case NFC_DIGITAL_RF_TECH_212F:
trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_NFC_NFC_CE_MODE |
TRF7970A_ISO_CTRL_NFC_NFCF_212;
- trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_ASK10;
+ trf->modulator_sys_clk_ctrl =
+ (trf->modulator_sys_clk_ctrl & 0xF8) |
+ TRF7970A_MODULATOR_DEPTH_ASK10;
break;
case NFC_DIGITAL_RF_TECH_424F:
trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_NFC_NFC_CE_MODE |
TRF7970A_ISO_CTRL_NFC_NFCF_424;
- trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_ASK10;
+ trf->modulator_sys_clk_ctrl =
+ (trf->modulator_sys_clk_ctrl & 0xF8) |
+ TRF7970A_MODULATOR_DEPTH_ASK10;
break;
default:
dev_dbg(trf->dev, "Unsupported rf technology: %d\n", tech);
@@ -1987,6 +2005,7 @@ static int trf7970a_probe(struct spi_device *spi)
struct device_node *np = spi->dev.of_node;
struct trf7970a *trf;
int uvolts, autosuspend_delay, ret;
+ u32 clk_freq = 13560000;
if (!np) {
dev_err(&spi->dev, "No Device Tree entry\n");
@@ -2043,6 +2062,15 @@ static int trf7970a_probe(struct spi_device *spi)
return ret;
}
+ of_property_read_u32(np, "clock-frequency", &clk_freq);
+ if ((clk_freq != TRF7970A_27MHZ_CLOCK_FREQUENCY) ||
+ (clk_freq != TRF7970A_27MHZ_CLOCK_FREQUENCY)) {
+ dev_err(trf->dev,
+ "clock-frequency (%u Hz) unsupported\n",
+ clk_freq);
+ return -EINVAL;
+ }
+
if (of_property_read_bool(np, "en2-rf-quirk"))
trf->quirks |= TRF7970A_QUIRK_EN2_MUST_STAY_LOW;
--
Signed-off-by: Geoff Lansberry <geoff@kuvee.com>
^ permalink raw reply related [flat|nested] 18+ messages in thread* [PATCH 1/3] NFC: trf7970a: add device tree option for 27MHz clock
@ 2016-12-20 16:16 Geoff Lansberry
2016-12-20 17:58 ` Jones Desougi
2016-12-20 18:11 ` Mark Greer
0 siblings, 2 replies; 18+ messages in thread
From: Geoff Lansberry @ 2016-12-20 16:16 UTC (permalink / raw)
To: linux-wireless
Cc: lauro.venancio, aloisio.almeida, sameo, robh+dt, mark.rutland,
netdev, devicetree, linux-kernel, mgreer, justin,
Geoff Lansberry
From: Geoff Lansberry <geoff@kuvee.com>
The TRF7970A has configuration options to support hardware designs
which use a 27.12MHz clock. This commit adds a device tree option
'clock-frequency' to support configuring the this chip for default
13.56MHz clock or the optional 27.12MHz clock.
---
.../devicetree/bindings/net/nfc/trf7970a.txt | 4 ++
drivers/nfc/trf7970a.c | 50 +++++++++++++++++-----
2 files changed, 43 insertions(+), 11 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
index 32b35a0..e262ac1 100644
--- a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
+++ b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
@@ -21,6 +21,8 @@ Optional SoC Specific Properties:
- t5t-rmb-extra-byte-quirk: Specify that the trf7970a has the erratum
where an extra byte is returned by Read Multiple Block commands issued
to Type 5 tags.
+- clock-frequency: Set to specify that the input frequency to the trf7970a is 13560000Hz or 27120000Hz
+
Example (for ARM-based BeagleBone with TRF7970A on SPI1):
@@ -43,6 +45,8 @@ Example (for ARM-based BeagleBone with TRF7970A on SPI1):
irq-status-read-quirk;
en2-rf-quirk;
t5t-rmb-extra-byte-quirk;
+ vdd_io_1v8;
+ clock-frequency = <27120000>;
status = "okay";
};
};
diff --git a/drivers/nfc/trf7970a.c b/drivers/nfc/trf7970a.c
index 26c9dbb..4e051e9 100644
--- a/drivers/nfc/trf7970a.c
+++ b/drivers/nfc/trf7970a.c
@@ -124,6 +124,9 @@
NFC_PROTO_ISO15693_MASK | NFC_PROTO_NFC_DEP_MASK)
#define TRF7970A_AUTOSUSPEND_DELAY 30000 /* 30 seconds */
+#define TRF7970A_13MHZ_CLOCK_FREQUENCY 13560000
+#define TRF7970A_27MHZ_CLOCK_FREQUENCY 27120000
+
#define TRF7970A_RX_SKB_ALLOC_SIZE 256
@@ -1056,12 +1059,11 @@ static int trf7970a_init(struct trf7970a *trf)
trf->chip_status_ctrl &= ~TRF7970A_CHIP_STATUS_RF_ON;
- ret = trf7970a_write(trf, TRF7970A_MODULATOR_SYS_CLK_CTRL, 0);
+ ret = trf7970a_write(trf, TRF7970A_MODULATOR_SYS_CLK_CTRL,
+ trf->modulator_sys_clk_ctrl);
if (ret)
goto err_out;
- trf->modulator_sys_clk_ctrl = 0;
-
ret = trf7970a_write(trf, TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS,
TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLH_96 |
TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLL_32);
@@ -1181,27 +1183,37 @@ static int trf7970a_in_config_rf_tech(struct trf7970a *trf, int tech)
switch (tech) {
case NFC_DIGITAL_RF_TECH_106A:
trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_14443A_106;
- trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_OOK;
+ trf->modulator_sys_clk_ctrl =
+ (trf->modulator_sys_clk_ctrl & 0xF8) |
+ TRF7970A_MODULATOR_DEPTH_OOK;
trf->guard_time = TRF7970A_GUARD_TIME_NFCA;
break;
case NFC_DIGITAL_RF_TECH_106B:
trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_14443B_106;
- trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_ASK10;
+ trf->modulator_sys_clk_ctrl =
+ (trf->modulator_sys_clk_ctrl & 0xF8) |
+ TRF7970A_MODULATOR_DEPTH_ASK10;
trf->guard_time = TRF7970A_GUARD_TIME_NFCB;
break;
case NFC_DIGITAL_RF_TECH_212F:
trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_FELICA_212;
- trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_ASK10;
+ trf->modulator_sys_clk_ctrl =
+ (trf->modulator_sys_clk_ctrl & 0xF8) |
+ TRF7970A_MODULATOR_DEPTH_ASK10;
trf->guard_time = TRF7970A_GUARD_TIME_NFCF;
break;
case NFC_DIGITAL_RF_TECH_424F:
trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_FELICA_424;
- trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_ASK10;
+ trf->modulator_sys_clk_ctrl =
+ (trf->modulator_sys_clk_ctrl & 0xF8) |
+ TRF7970A_MODULATOR_DEPTH_ASK10;
trf->guard_time = TRF7970A_GUARD_TIME_NFCF;
break;
case NFC_DIGITAL_RF_TECH_ISO15693:
trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_15693_SGL_1OF4_2648;
- trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_OOK;
+ trf->modulator_sys_clk_ctrl =
+ (trf->modulator_sys_clk_ctrl & 0xF8) |
+ TRF7970A_MODULATOR_DEPTH_OOK;
trf->guard_time = TRF7970A_GUARD_TIME_15693;
break;
default:
@@ -1571,17 +1583,23 @@ static int trf7970a_tg_config_rf_tech(struct trf7970a *trf, int tech)
trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_NFC_NFC_CE_MODE |
TRF7970A_ISO_CTRL_NFC_CE |
TRF7970A_ISO_CTRL_NFC_CE_14443A;
- trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_OOK;
+ trf->modulator_sys_clk_ctrl =
+ (trf->modulator_sys_clk_ctrl & 0xF8) |
+ TRF7970A_MODULATOR_DEPTH_OOK;
break;
case NFC_DIGITAL_RF_TECH_212F:
trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_NFC_NFC_CE_MODE |
TRF7970A_ISO_CTRL_NFC_NFCF_212;
- trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_ASK10;
+ trf->modulator_sys_clk_ctrl =
+ (trf->modulator_sys_clk_ctrl & 0xF8) |
+ TRF7970A_MODULATOR_DEPTH_ASK10;
break;
case NFC_DIGITAL_RF_TECH_424F:
trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_NFC_NFC_CE_MODE |
TRF7970A_ISO_CTRL_NFC_NFCF_424;
- trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_ASK10;
+ trf->modulator_sys_clk_ctrl =
+ (trf->modulator_sys_clk_ctrl & 0xF8) |
+ TRF7970A_MODULATOR_DEPTH_ASK10;
break;
default:
dev_dbg(trf->dev, "Unsupported rf technology: %d\n", tech);
@@ -1987,6 +2005,7 @@ static int trf7970a_probe(struct spi_device *spi)
struct device_node *np = spi->dev.of_node;
struct trf7970a *trf;
int uvolts, autosuspend_delay, ret;
+ u32 clk_freq = 13560000;
if (!np) {
dev_err(&spi->dev, "No Device Tree entry\n");
@@ -2043,6 +2062,15 @@ static int trf7970a_probe(struct spi_device *spi)
return ret;
}
+ of_property_read_u32(np, "clock-frequency", &clk_freq);
+ if ((clk_freq != TRF7970A_27MHZ_CLOCK_FREQUENCY) ||
+ (clk_freq != TRF7970A_27MHZ_CLOCK_FREQUENCY)) {
+ dev_err(trf->dev,
+ "clock-frequency (%u Hz) unsupported\n",
+ clk_freq);
+ return -EINVAL;
+ }
+
if (of_property_read_bool(np, "en2-rf-quirk"))
trf->quirks |= TRF7970A_QUIRK_EN2_MUST_STAY_LOW;
--
Signed-off-by: Geoff Lansberry <geoff@kuvee.com>
^ permalink raw reply related [flat|nested] 18+ messages in thread* Re: [PATCH 1/3] NFC: trf7970a: add device tree option for 27MHz clock
2016-12-20 16:16 Geoff Lansberry
@ 2016-12-20 17:58 ` Jones Desougi
2016-12-20 18:11 ` Mark Greer
1 sibling, 0 replies; 18+ messages in thread
From: Jones Desougi @ 2016-12-20 17:58 UTC (permalink / raw)
To: Geoff Lansberry, linux-wireless
Cc: lauro.venancio, aloisio.almeida, sameo, robh+dt, mark.rutland,
netdev, devicetree, linux-kernel, mgreer, justin
On 2016-12-20 17:16, Geoff Lansberry wrote:
> From: Geoff Lansberry <geoff@kuvee.com>
>
> The TRF7970A has configuration options to support hardware designs
> which use a 27.12MHz clock. This commit adds a device tree option
> 'clock-frequency' to support configuring the this chip for default
> 13.56MHz clock or the optional 27.12MHz clock.
> ---
> .../devicetree/bindings/net/nfc/trf7970a.txt | 4 ++
> drivers/nfc/trf7970a.c | 50 +++++++++++++++++-----
> 2 files changed, 43 insertions(+), 11 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
> index 32b35a0..e262ac1 100644
> --- a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
> +++ b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
> @@ -21,6 +21,8 @@ Optional SoC Specific Properties:
> - t5t-rmb-extra-byte-quirk: Specify that the trf7970a has the erratum
> where an extra byte is returned by Read Multiple Block commands issued
> to Type 5 tags.
> +- clock-frequency: Set to specify that the input frequency to the trf7970a is 13560000Hz or 27120000Hz
> +
You're adding an empty line here that is removed in the next patch.
>
> Example (for ARM-based BeagleBone with TRF7970A on SPI1):
>
> @@ -43,6 +45,8 @@ Example (for ARM-based BeagleBone with TRF7970A on SPI1):
> irq-status-read-quirk;
> en2-rf-quirk;
> t5t-rmb-extra-byte-quirk;
> + vdd_io_1v8;
This does not belong here, and so no need to remove in the next patch.
> + clock-frequency = <27120000>;
> status = "okay";
> };
> };
> diff --git a/drivers/nfc/trf7970a.c b/drivers/nfc/trf7970a.c
> index 26c9dbb..4e051e9 100644
> --- a/drivers/nfc/trf7970a.c
> +++ b/drivers/nfc/trf7970a.c
> @@ -124,6 +124,9 @@
> NFC_PROTO_ISO15693_MASK | NFC_PROTO_NFC_DEP_MASK)
>
> #define TRF7970A_AUTOSUSPEND_DELAY 30000 /* 30 seconds */
> +#define TRF7970A_13MHZ_CLOCK_FREQUENCY 13560000
> +#define TRF7970A_27MHZ_CLOCK_FREQUENCY 27120000
> +
>
> #define TRF7970A_RX_SKB_ALLOC_SIZE 256
>
> @@ -1056,12 +1059,11 @@ static int trf7970a_init(struct trf7970a *trf)
>
> trf->chip_status_ctrl &= ~TRF7970A_CHIP_STATUS_RF_ON;
>
> - ret = trf7970a_write(trf, TRF7970A_MODULATOR_SYS_CLK_CTRL, 0);
> + ret = trf7970a_write(trf, TRF7970A_MODULATOR_SYS_CLK_CTRL,
> + trf->modulator_sys_clk_ctrl);
> if (ret)
> goto err_out;
>
> - trf->modulator_sys_clk_ctrl = 0;
> -
> ret = trf7970a_write(trf, TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS,
> TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLH_96 |
> TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLL_32);
> @@ -1181,27 +1183,37 @@ static int trf7970a_in_config_rf_tech(struct trf7970a *trf, int tech)
> switch (tech) {
> case NFC_DIGITAL_RF_TECH_106A:
> trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_14443A_106;
> - trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_OOK;
> + trf->modulator_sys_clk_ctrl =
> + (trf->modulator_sys_clk_ctrl & 0xF8) |
> + TRF7970A_MODULATOR_DEPTH_OOK;
> trf->guard_time = TRF7970A_GUARD_TIME_NFCA;
> break;
> case NFC_DIGITAL_RF_TECH_106B:
> trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_14443B_106;
> - trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_ASK10;
> + trf->modulator_sys_clk_ctrl =
> + (trf->modulator_sys_clk_ctrl & 0xF8) |
> + TRF7970A_MODULATOR_DEPTH_ASK10;
> trf->guard_time = TRF7970A_GUARD_TIME_NFCB;
> break;
> case NFC_DIGITAL_RF_TECH_212F:
> trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_FELICA_212;
> - trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_ASK10;
> + trf->modulator_sys_clk_ctrl =
> + (trf->modulator_sys_clk_ctrl & 0xF8) |
> + TRF7970A_MODULATOR_DEPTH_ASK10;
> trf->guard_time = TRF7970A_GUARD_TIME_NFCF;
> break;
> case NFC_DIGITAL_RF_TECH_424F:
> trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_FELICA_424;
> - trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_ASK10;
> + trf->modulator_sys_clk_ctrl =
> + (trf->modulator_sys_clk_ctrl & 0xF8) |
> + TRF7970A_MODULATOR_DEPTH_ASK10;
> trf->guard_time = TRF7970A_GUARD_TIME_NFCF;
> break;
> case NFC_DIGITAL_RF_TECH_ISO15693:
> trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_15693_SGL_1OF4_2648;
> - trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_OOK;
> + trf->modulator_sys_clk_ctrl =
> + (trf->modulator_sys_clk_ctrl & 0xF8) |
> + TRF7970A_MODULATOR_DEPTH_OOK;
> trf->guard_time = TRF7970A_GUARD_TIME_15693;
> break;
> default:
> @@ -1571,17 +1583,23 @@ static int trf7970a_tg_config_rf_tech(struct trf7970a *trf, int tech)
> trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_NFC_NFC_CE_MODE |
> TRF7970A_ISO_CTRL_NFC_CE |
> TRF7970A_ISO_CTRL_NFC_CE_14443A;
> - trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_OOK;
> + trf->modulator_sys_clk_ctrl =
> + (trf->modulator_sys_clk_ctrl & 0xF8) |
> + TRF7970A_MODULATOR_DEPTH_OOK;
> break;
> case NFC_DIGITAL_RF_TECH_212F:
> trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_NFC_NFC_CE_MODE |
> TRF7970A_ISO_CTRL_NFC_NFCF_212;
> - trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_ASK10;
> + trf->modulator_sys_clk_ctrl =
> + (trf->modulator_sys_clk_ctrl & 0xF8) |
> + TRF7970A_MODULATOR_DEPTH_ASK10;
> break;
> case NFC_DIGITAL_RF_TECH_424F:
> trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_NFC_NFC_CE_MODE |
> TRF7970A_ISO_CTRL_NFC_NFCF_424;
> - trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_DEPTH_ASK10;
> + trf->modulator_sys_clk_ctrl =
> + (trf->modulator_sys_clk_ctrl & 0xF8) |
> + TRF7970A_MODULATOR_DEPTH_ASK10;
> break;
> default:
> dev_dbg(trf->dev, "Unsupported rf technology: %d\n", tech);
> @@ -1987,6 +2005,7 @@ static int trf7970a_probe(struct spi_device *spi)
> struct device_node *np = spi->dev.of_node;
> struct trf7970a *trf;
> int uvolts, autosuspend_delay, ret;
> + u32 clk_freq = 13560000;
Use TRF7970A_13MHZ_CLOCK_FREQUENCY here?
>
> if (!np) {
> dev_err(&spi->dev, "No Device Tree entry\n");
> @@ -2043,6 +2062,15 @@ static int trf7970a_probe(struct spi_device *spi)
> return ret;
> }
>
> + of_property_read_u32(np, "clock-frequency", &clk_freq);
> + if ((clk_freq != TRF7970A_27MHZ_CLOCK_FREQUENCY) ||
> + (clk_freq != TRF7970A_27MHZ_CLOCK_FREQUENCY)) {
Two comparisons with 27MHz, missing 13MHz.
> + dev_err(trf->dev,
> + "clock-frequency (%u Hz) unsupported\n",
> + clk_freq);
> + return -EINVAL;
> + }
> +
> if (of_property_read_bool(np, "en2-rf-quirk"))
> trf->quirks |= TRF7970A_QUIRK_EN2_MUST_STAY_LOW;
>
>
^ permalink raw reply [flat|nested] 18+ messages in thread* Re: [PATCH 1/3] NFC: trf7970a: add device tree option for 27MHz clock
2016-12-20 16:16 Geoff Lansberry
2016-12-20 17:58 ` Jones Desougi
@ 2016-12-20 18:11 ` Mark Greer
2016-12-20 18:29 ` Geoff Lansberry
1 sibling, 1 reply; 18+ messages in thread
From: Mark Greer @ 2016-12-20 18:11 UTC (permalink / raw)
To: Geoff Lansberry
Cc: linux-wireless, lauro.venancio, aloisio.almeida, sameo, robh+dt,
mark.rutland, netdev, devicetree, linux-kernel, justin
Hi Geoff.
Please put the version in your subjects when submitting anything but the
initial version of a patch (e.g., [PATCH v2 1/3]).
Which series do you want reviewed?
Mark
--
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 1/3] NFC: trf7970a: add device tree option for 27MHz clock
2016-12-20 18:11 ` Mark Greer
@ 2016-12-20 18:29 ` Geoff Lansberry
2016-12-20 18:35 ` Mark Greer
0 siblings, 1 reply; 18+ messages in thread
From: Geoff Lansberry @ 2016-12-20 18:29 UTC (permalink / raw)
To: Mark Greer
Cc: linux-wireless, Lauro Ramos Venancio, Aloisio Almeida Jr,
Samuel Ortiz, robh+dt, mark.rutland, netdev, devicetree,
linux-kernel, Justin Bronder
On Tue, Dec 20, 2016 at 1:11 PM, Mark Greer <mgreer@animalcreek.com> wrote:
> Hi Geoff.
>
> Please put the version in your subjects when submitting anything but the
> initial version of a patch (e.g., [PATCH v2 1/3]).
>
> Which series do you want reviewed?
>
> Mark
> --
Sorry about the double posting, I had forgotten to erase the patches I
generated while rebasing and checking, and I'll have to figure out how
to add that v2 line to the automatically generated subject line if I
end up submitting another round.
Please review the three most recent patches, which have the send time
of 17:16.
Best Regards,
Geoff
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 1/3] NFC: trf7970a: add device tree option for 27MHz clock
2016-12-20 18:29 ` Geoff Lansberry
@ 2016-12-20 18:35 ` Mark Greer
0 siblings, 0 replies; 18+ messages in thread
From: Mark Greer @ 2016-12-20 18:35 UTC (permalink / raw)
To: Geoff Lansberry
Cc: linux-wireless, Lauro Ramos Venancio, Aloisio Almeida Jr,
Samuel Ortiz, robh+dt, mark.rutland, netdev, devicetree,
linux-kernel, Justin Bronder
On Tue, Dec 20, 2016 at 01:29:13PM -0500, Geoff Lansberry wrote:
> On Tue, Dec 20, 2016 at 1:11 PM, Mark Greer <mgreer@animalcreek.com> wrote:
> > Hi Geoff.
> >
> > Please put the version in your subjects when submitting anything but the
> > initial version of a patch (e.g., [PATCH v2 1/3]).
> >
> > Which series do you want reviewed?
> >
> > Mark
> > --
> Sorry about the double posting, I had forgotten to erase the patches I
> generated while rebasing and checking, and I'll have to figure out how
> to add that v2 line to the automatically generated subject line if I
> end up submitting another round.
Hint: -v <n> option of 'git format-patch'
> Please review the three most recent patches, which have the send time
> of 17:16.
Okay, thank.
Mark
--
^ permalink raw reply [flat|nested] 18+ messages in thread
end of thread, other threads:[~2016-12-22 18:48 UTC | newest]
Thread overview: 18+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-12-15 22:30 [PATCH 1/3] NFC: trf7970a: add device tree option for 27MHz clock Geoff Lansberry
2016-12-15 22:30 ` [PATCH 2/3] NFC: trf7970a: Add device tree option of 1.8 Volt IO voltage Geoff Lansberry
2016-12-16 1:13 ` Mark Greer
2016-12-19 22:35 ` Rob Herring
2016-12-20 16:13 ` Geoff Lansberry
2016-12-21 2:07 ` Mark Greer
2016-12-15 22:30 ` [PATCH 3/3] nfc: trf7970a: Prevent repeated polling from crashing the kernel Geoff Lansberry
2016-12-16 1:18 ` Mark Greer
2016-12-16 1:06 ` [PATCH 1/3] NFC: trf7970a: add device tree option for 27MHz clock Mark Greer
2016-12-19 22:31 ` Rob Herring
2016-12-19 23:23 ` Geoff Lansberry
2016-12-22 18:48 ` Rob Herring
2016-12-20 16:10 Geoff Lansberry
2016-12-20 16:16 Geoff Lansberry
2016-12-20 17:58 ` Jones Desougi
2016-12-20 18:11 ` Mark Greer
2016-12-20 18:29 ` Geoff Lansberry
2016-12-20 18:35 ` Mark Greer
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).