linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Sakari Ailus <sakari.ailus@iki.fi>
To: Pavel Machek <pavel@ucw.cz>
Cc: Rob Herring <robh@kernel.org>,
	ivo.g.dimitrov.75@gmail.com, sre@kernel.org,
	pali.rohar@gmail.com, linux-media@vger.kernel.org,
	pawel.moll@arm.com, mark.rutland@arm.com,
	ijc+devicetree@hellion.org.uk, galak@codeaurora.org,
	mchehab@osg.samsung.com, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org
Subject: Re: [PATCH v6] media: et8ek8: add device tree binding documentation
Date: Tue, 20 Dec 2016 15:05:39 +0200	[thread overview]
Message-ID: <20161220130538.GD16630@valkosipuli.retiisi.org.uk> (raw)
In-Reply-To: <20161114183040.GB28778@amd>

Hi Pavel,

On Mon, Nov 14, 2016 at 07:30:40PM +0100, Pavel Machek wrote:
> Add device tree binding documentation for toshiba et8ek8 sensor.
> 
> Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
> Signed-off-by: Pavel Machek <pavel@ucw.cz>
> 
> ---
> 
> v6: added missing article, fixed signal polarity.
> 
> diff --git a/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt b/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt
> new file mode 100644
> index 0000000..b03b21d
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt
> @@ -0,0 +1,53 @@
> +Toshiba et8ek8 5MP sensor
> +
> +Toshiba et8ek8 5MP sensor is an image sensor found in Nokia N900 device
> +
> +More detailed documentation can be found in
> +Documentation/devicetree/bindings/media/video-interfaces.txt .
> +
> +
> +Mandatory properties
> +--------------------
> +
> +- compatible: "toshiba,et8ek8"
> +- reg: I2C address (0x3e, or an alternative address)
> +- vana-supply: Analogue voltage supply (VANA), 2.8 volts
> +- clocks: External clock to the sensor
> +- clock-frequency: Frequency of the external clock to the sensor. Camera
> +  driver will set this frequency on the external clock. The clock frequency is
> +  a pre-determined frequency known to be suitable to the board.
> +- reset-gpios: XSHUTDOWN GPIO. The XSHUTDOWN signal is active low. The sensor
> +  is in hardware standby mode when the signal is in the low state.
> +
> +
> +Endpoint node mandatory properties
> +----------------------------------
> +
> +- remote-endpoint: A phandle to the bus receiver's endpoint node.
> +
> +Endpoint node optional properties
> +----------------------------------
> +
> +- clock-lanes: <0>
> +- data-lanes: <1..n>

The driver makes no use of them and CCP2 only supports a single lane. I'll
just remove these and apply it to my tree. Let's continue discussing the
driver patch in the other thread.

> +
> +Example
> +-------
> +
> +&i2c3 {
> +	clock-frequency = <400000>;
> +
> +	cam1: camera@3e {
> +		compatible = "toshiba,et8ek8";
> +		reg = <0x3e>;
> +		vana-supply = <&vaux4>;
> +		clocks = <&isp 0>;
> +		clock-frequency = <9600000>;
> +		reset-gpio = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* 102 */
> +		port {
> +			csi_cam1: endpoint {
> +				remote-endpoint = <&csi_out1>;
> +			};
> +		};
> +	};
> +};
> 

-- 
Regards,

Sakari Ailus
e-mail: sakari.ailus@iki.fi	XMPP: sailus@retiisi.org.uk

  parent reply	other threads:[~2016-12-20 13:06 UTC|newest]

Thread overview: 14+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2016-10-23 19:17 [PATCH v4] media: et8ek8: add device tree binding documentation Pavel Machek
2016-10-23 20:06 ` Sakari Ailus
2016-10-30 20:41 ` Rob Herring
2016-10-31 22:47   ` Sakari Ailus
2016-11-03 12:47   ` Pavel Machek
2016-11-03 22:20     ` Sakari Ailus
2016-11-07 10:36       ` Pavel Machek
2016-11-07 10:46   ` [PATCH v5] " Pavel Machek
2016-11-11 12:17     ` Pavel Machek
2016-11-14 16:20     ` Rob Herring
2016-11-14 18:30     ` [PATCH v6] " Pavel Machek
2016-11-14 18:39       ` Rob Herring
2016-12-20 13:05       ` Sakari Ailus [this message]
2016-12-21 13:20         ` Pavel Machek

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20161220130538.GD16630@valkosipuli.retiisi.org.uk \
    --to=sakari.ailus@iki.fi \
    --cc=devicetree@vger.kernel.org \
    --cc=galak@codeaurora.org \
    --cc=ijc+devicetree@hellion.org.uk \
    --cc=ivo.g.dimitrov.75@gmail.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-media@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=mchehab@osg.samsung.com \
    --cc=pali.rohar@gmail.com \
    --cc=pavel@ucw.cz \
    --cc=pawel.moll@arm.com \
    --cc=robh@kernel.org \
    --cc=sre@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).