From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1752649AbcL1XBE (ORCPT ); Wed, 28 Dec 2016 18:01:04 -0500 Received: from mail-pg0-f51.google.com ([74.125.83.51]:36079 "EHLO mail-pg0-f51.google.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1752209AbcL1W51 (ORCPT ); Wed, 28 Dec 2016 17:57:27 -0500 From: Stephen Boyd To: linux-usb@vger.kernel.org Cc: Peter Chen , linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, linux-arm-msm@vger.kernel.org, Andy Gross , Bjorn Andersson , Neil Armstrong , Arnd Bergmann , Felipe Balbi Subject: [PATCH v6 11/25] usb: chipidea: vbus event may exist before starting gadget Date: Wed, 28 Dec 2016 14:56:57 -0800 Message-Id: <20161228225711.698-12-stephen.boyd@linaro.org> X-Mailer: git-send-email 2.10.0.297.gf6727b0 In-Reply-To: <20161228225711.698-1-stephen.boyd@linaro.org> References: <20161228225711.698-1-stephen.boyd@linaro.org> Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org From: Peter Chen At some situations, the vbus may already be there before starting gadget. So we need to check vbus event after switch to gadget in order to handle missing vbus event. The typical use cases are plugging vbus cable before driver load or the vbus has already been there after stopping host but before starting gadget. Signed-off-by: Peter Chen Tested-by: Stephen Boyd Reviewed-by: Stephen Boyd [sboyd@codeaurora.org: Modify comment text per list discussion] Signed-off-by: Stephen Boyd --- drivers/usb/chipidea/core.c | 4 ---- drivers/usb/chipidea/otg.c | 14 +++++++++----- drivers/usb/chipidea/udc.c | 2 ++ 3 files changed, 11 insertions(+), 9 deletions(-) diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c index 8a020ebbbe2f..37f888e31f10 100644 --- a/drivers/usb/chipidea/core.c +++ b/drivers/usb/chipidea/core.c @@ -979,10 +979,6 @@ static int ci_hdrc_probe(struct platform_device *pdev) } if (!ci_otg_is_fsm_mode(ci)) { - /* only update vbus status for peripheral */ - if (ci->role == CI_ROLE_GADGET) - ci_handle_vbus_change(ci); - ret = ci_role_start(ci, ci->role); if (ret) { dev_err(dev, "can't start %s role\n", diff --git a/drivers/usb/chipidea/otg.c b/drivers/usb/chipidea/otg.c index 695f3fe3ae21..c972ed23b8ec 100644 --- a/drivers/usb/chipidea/otg.c +++ b/drivers/usb/chipidea/otg.c @@ -134,9 +134,9 @@ void ci_handle_vbus_change(struct ci_hdrc *ci) if (!ci->is_otg) return; - if (hw_read_otgsc(ci, OTGSC_BSV)) + if (hw_read_otgsc(ci, OTGSC_BSV) && !ci->vbus_active) usb_gadget_vbus_connect(&ci->gadget); - else + else if (!hw_read_otgsc(ci, OTGSC_BSV) && ci->vbus_active) usb_gadget_vbus_disconnect(&ci->gadget); } @@ -175,10 +175,14 @@ static void ci_handle_id_switch(struct ci_hdrc *ci) ci_role_stop(ci); - if (role == CI_ROLE_GADGET) + if (role == CI_ROLE_GADGET && + IS_ERR(ci->platdata->vbus_extcon.edev)) /* - * wait vbus lower than OTGSC_BSV before connecting - * to host + * wait vbus lower than OTGSC_BSV before connecting to + * host. If connecting status is from an external + * connector instead of register, we don't need to care + * vbus on the board, since it will not affect external + * connector status. */ hw_wait_vbus_lower_bsv(ci); diff --git a/drivers/usb/chipidea/udc.c b/drivers/usb/chipidea/udc.c index 732b281485de..0db56fb7e9e9 100644 --- a/drivers/usb/chipidea/udc.c +++ b/drivers/usb/chipidea/udc.c @@ -1961,6 +1961,8 @@ static int udc_id_switch_for_device(struct ci_hdrc *ci) /* Clear and enable BSV irq */ hw_write_otgsc(ci, OTGSC_BSVIS | OTGSC_BSVIE, OTGSC_BSVIS | OTGSC_BSVIE); + /* vbus change may has already been occurred */ + ci_handle_vbus_change(ci); return 0; } -- 2.10.0.297.gf6727b0