From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1752677AbcL1XCt (ORCPT ); Wed, 28 Dec 2016 18:02:49 -0500 Received: from mail-pg0-f54.google.com ([74.125.83.54]:36066 "EHLO mail-pg0-f54.google.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1751906AbcL1W5V (ORCPT ); Wed, 28 Dec 2016 17:57:21 -0500 From: Stephen Boyd To: linux-usb@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, linux-arm-msm@vger.kernel.org, Andy Gross , Bjorn Andersson , Neil Armstrong , Arnd Bergmann , Felipe Balbi , Peter Chen , Greg Kroah-Hartman Subject: [PATCH v6 06/25] usb: chipidea: Add platform flag for wrapper phy management Date: Wed, 28 Dec 2016 14:56:52 -0800 Message-Id: <20161228225711.698-7-stephen.boyd@linaro.org> X-Mailer: git-send-email 2.10.0.297.gf6727b0 In-Reply-To: <20161228225711.698-1-stephen.boyd@linaro.org> References: <20161228225711.698-1-stephen.boyd@linaro.org> Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org The ULPI phy on qcom platforms needs to be initialized and powered on after a USB reset and before we toggle the run/stop bit. Otherwise, the phy locks up and doesn't work properly. Therefore, add a flag to skip any phy power management in the core layer, leaving it up to the glue driver to manage. Acked-by: Peter Chen Cc: Greg Kroah-Hartman Signed-off-by: Stephen Boyd --- drivers/usb/chipidea/core.c | 6 ++++++ include/linux/usb/chipidea.h | 1 + 2 files changed, 7 insertions(+) diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c index 6e0d614a8075..3d15aee84a6a 100644 --- a/drivers/usb/chipidea/core.c +++ b/drivers/usb/chipidea/core.c @@ -361,6 +361,9 @@ static int _ci_usb_phy_init(struct ci_hdrc *ci) */ static void ci_usb_phy_exit(struct ci_hdrc *ci) { + if (ci->platdata->flags & CI_HDRC_OVERRIDE_PHY_CONTROL) + return; + if (ci->phy) { phy_power_off(ci->phy); phy_exit(ci->phy); @@ -379,6 +382,9 @@ static int ci_usb_phy_init(struct ci_hdrc *ci) { int ret; + if (ci->platdata->flags & CI_HDRC_OVERRIDE_PHY_CONTROL) + return 0; + switch (ci->platdata->phy_mode) { case USBPHY_INTERFACE_MODE_UTMI: case USBPHY_INTERFACE_MODE_UTMIW: diff --git a/include/linux/usb/chipidea.h b/include/linux/usb/chipidea.h index f9be467d6695..d07b162073f7 100644 --- a/include/linux/usb/chipidea.h +++ b/include/linux/usb/chipidea.h @@ -57,6 +57,7 @@ struct ci_hdrc_platform_data { #define CI_HDRC_OVERRIDE_AHB_BURST BIT(9) #define CI_HDRC_OVERRIDE_TX_BURST BIT(10) #define CI_HDRC_OVERRIDE_RX_BURST BIT(11) +#define CI_HDRC_OVERRIDE_PHY_CONTROL BIT(12) /* Glue layer manages phy */ enum usb_dr_mode dr_mode; #define CI_HDRC_CONTROLLER_RESET_EVENT 0 #define CI_HDRC_CONTROLLER_STOPPED_EVENT 1 -- 2.10.0.297.gf6727b0