From mboxrd@z Thu Jan  1 00:00:00 1970
Return-Path: <linux-kernel-owner@vger.kernel.org>
Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand
        id S1754272AbdCMQlk (ORCPT <rfc822;w@1wt.eu>);
        Mon, 13 Mar 2017 12:41:40 -0400
Received: from vps0.lunn.ch ([178.209.37.122]:46213 "EHLO vps0.lunn.ch"
        rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP
        id S1754161AbdCMQl3 (ORCPT <rfc822;linux-kernel@vger.kernel.org>);
        Mon, 13 Mar 2017 12:41:29 -0400
Date: Mon, 13 Mar 2017 17:41:18 +0100
From: Andrew Lunn <andrew@lunn.ch>
To: sean.wang@mediatek.com
Cc: f.fainelli@gmail.com, vivien.didelot@savoirfairelinux.com,
        matthias.bgg@gmail.com, robh+dt@kernel.org, mark.rutland@arm.com,
        devicetree@vger.kernel.org, netdev@vger.kernel.org,
        linux-kernel@vger.kernel.org, linux-mediatek@lists.infradead.org,
        davem@davemloft.net, Landen.Chao@mediatek.com, keyhaede@gmail.com,
        objelf@gmail.com
Subject: Re: [PATCH net-next 4/4] net-next: dsa: add dsa support for Mediatek
 MT7530 switch
Message-ID: <20170313164118.GE3953@lunn.ch>
References: <1489421488-300-1-git-send-email-sean.wang@mediatek.com>
 <1489421488-300-5-git-send-email-sean.wang@mediatek.com>
MIME-Version: 1.0
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline
In-Reply-To: <1489421488-300-5-git-send-email-sean.wang@mediatek.com>
User-Agent: Mutt/1.5.21 (2010-09-15)
Sender: linux-kernel-owner@vger.kernel.org
List-ID: <linux-kernel.vger.kernel.org>
X-Mailing-List: linux-kernel@vger.kernel.org

Hi Sean

Just looking at the GPIO handling at the moment.

> +	/* Reset whole chip through gpio pin or
> +	 * memory-mapped registers for different
> +	 * type of hardware
> +	 */
> +	if (priv->mcm) {
> +		regmap_update_bits(priv->ethsys, SYSC_REG_RSTCTRL,
> +				   RESET_MCM, RESET_MCM);
> +		usleep_range(1000, 1100);
> +		regmap_update_bits(priv->ethsys, SYSC_REG_RSTCTRL,
> +				   RESET_MCM, ~RESET_MCM);
> +	} else {
> +		gpio_direction_output(priv->reset, 0);
> +		usleep_range(1000, 1100);
> +		gpio_set_value(priv->reset, 1);
> +	}

....

> +	/* Not MCM that indicates switch works as the remote standalone
> +	 * integrated circuit so the GPIO pin would be used to complete
> +	 * the reset, otherwise memory-mapped register accessing used
> +	 * through syscon provides in the case of MCM.
> +	 */
> +	if (!priv->mcm) {
> +		priv->reset = of_get_named_gpio(dn, "mediatek,reset-pin", 0);
> +		if (!gpio_is_valid(priv->reset))
> +			return priv->reset;
> +
> +		ret = devm_gpio_request_one(&mdiodev->dev,
> +					    priv->reset, GPIOF_OUT_INIT_LOW,
> +					    "mediatek,reset-pin");
> +		if (ret < 0) {
> +			dev_err(&mdiodev->dev,
> +				"fail to devm_gpio_request reset\n");
> +			return ret;
> +		}
> +	}

You are not handling the flags part of the GPIO binding. It is better
to use devm_gpiod_ API calls, which will handle the active low flags
for you.

    Andrew