linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Corentin Labbe <clabbe.montjoie@gmail.com>
To: robh+dt@kernel.org, mark.rutland@arm.com,
	maxime.ripard@free-electrons.com, wens@csie.org,
	linux@armlinux.org.uk, catalin.marinas@arm.com,
	will.deacon@arm.com, peppe.cavallaro@st.com,
	alexandre.torgue@st.com
Cc: devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
	netdev@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
	Corentin Labbe <clabbe.montjoie@gmail.com>
Subject: [PATCH v5 05/20] net: stmmac: Add dwmac-sun8i
Date: Mon,  1 May 2017 14:45:05 +0200	[thread overview]
Message-ID: <20170501124520.3769-6-clabbe.montjoie@gmail.com> (raw)
In-Reply-To: <20170501124520.3769-1-clabbe.montjoie@gmail.com>

The dwmac-sun8i is a heavy hacked version of stmmac hardware by
allwinner.
In fact the only common part is the descriptor management and the first
register function.

Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
---
 drivers/net/ethernet/stmicro/stmmac/Kconfig        |  11 +
 drivers/net/ethernet/stmicro/stmmac/Makefile       |   1 +
 drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c  | 973 +++++++++++++++++++++
 drivers/net/ethernet/stmicro/stmmac/stmmac_main.c  |  29 +
 .../net/ethernet/stmicro/stmmac/stmmac_platform.c  |   9 +-
 include/linux/stmmac.h                             |   1 +
 6 files changed, 1022 insertions(+), 2 deletions(-)
 create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c

diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
index cfbe363..85c0e41 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
+++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
@@ -145,6 +145,17 @@ config DWMAC_SUNXI
 	  This selects Allwinner SoC glue layer support for the
 	  stmmac device driver. This driver is used for A20/A31
 	  GMAC ethernet controller.
+
+config DWMAC_SUN8I
+	tristate "Allwinner sun8i GMAC support"
+	default ARCH_SUNXI
+	depends on OF && (ARCH_SUNXI || COMPILE_TEST)
+	---help---
+	  Support for Allwinner H3 A83T A64 EMAC ethernet controllers.
+
+	  This selects Allwinner SoC glue layer support for the
+	  stmmac device driver. This driver is used for H3/A83T/A64
+	  EMAC ethernet controller.
 endif
 
 config STMMAC_PCI
diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile
index 700c603..fd4937a 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Makefile
+++ b/drivers/net/ethernet/stmicro/stmmac/Makefile
@@ -16,6 +16,7 @@ obj-$(CONFIG_DWMAC_SOCFPGA)	+= dwmac-altr-socfpga.o
 obj-$(CONFIG_DWMAC_STI)		+= dwmac-sti.o
 obj-$(CONFIG_DWMAC_STM32)	+= dwmac-stm32.o
 obj-$(CONFIG_DWMAC_SUNXI)	+= dwmac-sunxi.o
+obj-$(CONFIG_DWMAC_SUN8I)	+= dwmac-sun8i.o
 obj-$(CONFIG_DWMAC_DWC_QOS_ETH)	+= dwmac-dwc-qos-eth.o
 obj-$(CONFIG_DWMAC_GENERIC)	+= dwmac-generic.o
 stmmac-platform-objs:= stmmac_platform.o
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
new file mode 100644
index 0000000..66eb980
--- /dev/null
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
@@ -0,0 +1,973 @@
+/*
+ * dwmac-sun8i.c - Allwinner sun8i DWMAC specific glue layer
+ *
+ * Copyright (C) 2017 Corentin Labbe <clabbe.montjoie@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/of_mdio.h>
+#include <linux/of_net.h>
+#include <linux/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/regmap.h>
+#include <linux/stmmac.h>
+
+#include "stmmac.h"
+#include "stmmac_platform.h"
+
+/* General notes on dwmac-sun8i:
+ * Locking: no locking is necessary in this file because all necessary locking
+ *		is done in the "stmmac files"
+ */
+
+/* struct emac_variant - Descrive dwmac-sun8i hardware variant
+ * @default_syscon_value:	The default value of the EMAC register in syscon
+ *				This value is used for disabling properly EMAC
+ *				and used as a good starting value in case of the
+ *				boot process(uboot) leave some stuff.
+ * @internal_phy:		Does the MAC embed an internal PHY
+ * @support_mii:		Does the MAC handle MII
+ * @support_rmii:		Does the MAC handle RMII
+ * @support_rgmii:		Does the MAC handle RGMII
+ */
+struct emac_variant {
+	u32 default_syscon_value;
+	int internal_phy;
+	bool support_mii;
+	bool support_rmii;
+	bool support_rgmii;
+};
+
+/* struct sunxi_priv_data - hold all sunxi private data
+ * @tx_clk:	reference to MAC TX clock
+ * @ephy_clk:	reference to the optional EPHY clock for the internal PHY
+ * @regulator:	reference to the optional regulator
+ * @rst_ephy:	reference to the optional EPHY reset for the internal PHY
+ * @variant:	reference to the current board variant
+ * @regmap:	regmap for using the syscon
+ * @use_internal_phy: Does the current PHY choice imply using the internal PHY
+ */
+struct sunxi_priv_data {
+	struct clk *tx_clk;
+	struct clk *ephy_clk;
+	struct regulator *regulator;
+	struct reset_control *rst_ephy;
+	const struct emac_variant *variant;
+	struct regmap *regmap;
+	bool use_internal_phy;
+};
+
+static const struct emac_variant emac_variant_h3 = {
+	.default_syscon_value = 0x58000,
+	.internal_phy = PHY_INTERFACE_MODE_MII,
+	.support_mii = true,
+	.support_rmii = true,
+	.support_rgmii = true
+};
+
+static const struct emac_variant emac_variant_a83t = {
+	.default_syscon_value = 0,
+	.internal_phy = 0,
+	.support_mii = true,
+	.support_rgmii = true
+};
+
+static const struct emac_variant emac_variant_a64 = {
+	.default_syscon_value = 0,
+	.internal_phy = 0,
+	.support_mii = true,
+	.support_rmii = true,
+	.support_rgmii = true
+};
+
+#define EMAC_BASIC_CTL0 0x00
+#define EMAC_BASIC_CTL1 0x04
+#define EMAC_INT_STA    0x08
+#define EMAC_INT_EN     0x0C
+#define EMAC_TX_CTL0    0x10
+#define EMAC_TX_CTL1    0x14
+#define EMAC_TX_FLOW_CTL        0x1C
+#define EMAC_TX_DESC_LIST 0x20
+#define EMAC_RX_CTL0    0x24
+#define EMAC_RX_CTL1    0x28
+#define EMAC_RX_DESC_LIST 0x34
+#define EMAC_RX_FRM_FLT 0x38
+#define EMAC_MDIO_CMD   0x48
+#define EMAC_MDIO_DATA  0x4C
+#define EMAC_MACADDR_HI(reg) (0x50 + (reg) * 8)
+#define EMAC_MACADDR_LO(reg) (0x54 + (reg) * 8)
+#define EMAC_TX_DMA_STA 0xB0
+#define EMAC_TX_CUR_DESC        0xB4
+#define EMAC_TX_CUR_BUF 0xB8
+#define EMAC_RX_DMA_STA 0xC0
+#define EMAC_RX_CUR_DESC        0xC4
+#define EMAC_RX_CUR_BUF 0xC8
+
+/* Use in EMAC_BASIC_CTL1 */
+#define EMAC_BURSTLEN_SHIFT		24
+
+/* Used in EMAC_RX_FRM_FLT */
+#define EMAC_FRM_FLT_RXALL              BIT(0)
+#define EMAC_FRM_FLT_CTL                BIT(13)
+#define EMAC_FRM_FLT_MULTICAST          BIT(16)
+
+/* Used in RX_CTL1*/
+#define EMAC_RX_MD              BIT(1)
+#define EMAC_RX_TH_MASK		GENMASK(4, 5)
+#define EMAC_RX_TH_32		0
+#define EMAC_RX_TH_64		(0x1 << 4)
+#define EMAC_RX_TH_96		(0x2 << 4)
+#define EMAC_RX_TH_128		(0x3 << 4)
+#define EMAC_RX_DMA_EN  BIT(30)
+#define EMAC_RX_DMA_START       BIT(31)
+
+/* Used in TX_CTL1*/
+#define EMAC_TX_MD              BIT(1)
+#define EMAC_TX_NEXT_FRM        BIT(2)
+#define EMAC_TX_TH_MASK		GENMASK(8, 10)
+#define EMAC_TX_TH_64		0
+#define EMAC_TX_TH_128		(0x1 << 8)
+#define EMAC_TX_TH_192		(0x2 << 8)
+#define EMAC_TX_TH_256		(0x3 << 8)
+#define EMAC_TX_DMA_EN  BIT(30)
+#define EMAC_TX_DMA_START       BIT(31)
+
+/* Used in RX_CTL0 */
+#define EMAC_RX_RECEIVER_EN             BIT(31)
+#define EMAC_RX_DO_CRC BIT(27)
+#define EMAC_RX_FLOW_CTL_EN             BIT(16)
+
+/* Used in TX_CTL0 */
+#define EMAC_TX_TRANSMITTER_EN  BIT(31)
+
+/* Used in EMAC_TX_FLOW_CTL */
+#define EMAC_TX_FLOW_CTL_EN             BIT(0)
+
+/* Used in EMAC_INT_STA */
+#define EMAC_TX_INT             BIT(0)
+#define EMAC_TX_DMA_STOP_INT    BIT(1)
+#define EMAC_TX_BUF_UA_INT      BIT(2)
+#define EMAC_TX_TIMEOUT_INT     BIT(3)
+#define EMAC_TX_UNDERFLOW_INT   BIT(4)
+#define EMAC_TX_EARLY_INT       BIT(5)
+#define EMAC_RX_INT             BIT(8)
+#define EMAC_RX_BUF_UA_INT      BIT(9)
+#define EMAC_RX_DMA_STOP_INT    BIT(10)
+#define EMAC_RX_TIMEOUT_INT     BIT(11)
+#define EMAC_RX_OVERFLOW_INT    BIT(12)
+#define EMAC_RX_EARLY_INT       BIT(13)
+#define EMAC_RGMII_STA_INT      BIT(16)
+
+#define MAC_ADDR_TYPE_DST BIT(31)
+
+/* H3 specific bits for EPHY */
+#define H3_EPHY_ADDR_SHIFT	20
+#define H3_EPHY_LED_POL		BIT(17) /* 1: active low, 0: active high */
+#define H3_EPHY_SHUTDOWN	BIT(16) /* 1: shutdown, 0: power up */
+#define H3_EPHY_SELECT		BIT(15) /* 1: internal PHY, 0: external PHY */
+
+/* H3/A64 specific bits */
+#define SYSCON_RMII_EN		BIT(13) /* 1: enable RMII (overrides EPIT) */
+
+/* Generic system control EMAC_CLK bits */
+#define SYSCON_ETXDC_MASK		GENMASK(2, 0)
+#define SYSCON_ETXDC_SHIFT		10
+#define SYSCON_ERXDC_MASK		GENMASK(4, 0)
+#define SYSCON_ERXDC_SHIFT		5
+/* EMAC PHY Interface Type */
+#define SYSCON_EPIT			BIT(2) /* 1: RGMII, 0: MII */
+#define SYSCON_ETCS_MASK		GENMASK(1, 0)
+#define SYSCON_ETCS_MII		0x0
+#define SYSCON_ETCS_EXT_GMII	0x1
+#define SYSCON_ETCS_INT_GMII	0x2
+#define SYSCON_EMAC_REG		0x30
+
+/* sun8i_dwmac_dma_reset() - reset the EMAC
+ * Called from stmmac via stmmac_dma_ops->reset
+ */
+static int sun8i_dwmac_dma_reset(void __iomem *ioaddr)
+{
+	writel(0, ioaddr + EMAC_RX_CTL1);
+	writel(0, ioaddr + EMAC_TX_CTL1);
+	writel(0, ioaddr + EMAC_RX_FRM_FLT);
+	writel(0, ioaddr + EMAC_RX_DESC_LIST);
+	writel(0, ioaddr + EMAC_TX_DESC_LIST);
+	writel(0, ioaddr + EMAC_INT_EN);
+	writel(0x1FFFFFF, ioaddr + EMAC_INT_STA);
+	return 0;
+}
+
+/* sun8i_dwmac_dma_init() - initialize the EMAC
+ * Called from stmmac via stmmac_dma_ops->init
+ */
+static void sun8i_dwmac_dma_init(void __iomem *ioaddr,
+				 struct stmmac_dma_cfg *dma_cfg,
+				 u32 dma_tx, u32 dma_rx, int atds)
+{
+	/* Write TX and RX descriptors address */
+	writel(dma_rx, ioaddr + EMAC_RX_DESC_LIST);
+	writel(dma_tx, ioaddr + EMAC_TX_DESC_LIST);
+
+	writel(EMAC_RX_INT | EMAC_TX_INT, ioaddr + EMAC_INT_EN);
+	writel(0x1FFFFFF, ioaddr + EMAC_INT_STA);
+}
+
+/* sun8i_dwmac_dump_regs() - Dump EMAC address space
+ * Called from stmmac_dma_ops->dump_regs
+ * Used for ethtool
+ */
+static void sun8i_dwmac_dump_regs(void __iomem *ioaddr, u32 *reg_space)
+{
+	int i;
+
+	for (i = 0; i < 0xC8; i += 4) {
+		if (i == 0x32 || i == 0x3C)
+			continue;
+		reg_space[i / 4] = readl(ioaddr + i);
+	}
+}
+
+/* sun8i_dwmac_dump_mac_regs() - Dump EMAC address space
+ * Called from stmmac_ops->dump_regs
+ * Used for ethtool
+ */
+static void sun8i_dwmac_dump_mac_regs(struct mac_device_info *hw,
+				      u32 *reg_space)
+{
+	int i;
+	void __iomem *ioaddr = hw->pcsr;
+
+	for (i = 0; i < 0xC8; i += 4) {
+		if (i == 0x32 || i == 0x3C)
+			continue;
+		reg_space[i / 4] = readl(ioaddr + i);
+	}
+}
+
+static void sun8i_dwmac_enable_dma_irq(void __iomem *ioaddr, u32 chan)
+{
+	writel(EMAC_RX_INT | EMAC_TX_INT, ioaddr + EMAC_INT_EN);
+}
+
+static void sun8i_dwmac_disable_dma_irq(void __iomem *ioaddr, u32 chan)
+{
+	writel(0, ioaddr + EMAC_INT_EN);
+}
+
+static void sun8i_dwmac_dma_start_tx(void __iomem *ioaddr, u32 chan)
+{
+	u32 v;
+
+	v = readl(ioaddr + EMAC_TX_CTL1);
+	v |= EMAC_TX_DMA_START;
+	v |= EMAC_TX_DMA_EN;
+	writel(v, ioaddr + EMAC_TX_CTL1);
+}
+
+static void sun8i_dwmac_enable_dma_transmission(void __iomem *ioaddr)
+{
+	u32 v;
+
+	v = readl(ioaddr + EMAC_TX_CTL1);
+	v |= EMAC_TX_DMA_START;
+	v |= EMAC_TX_DMA_EN;
+	writel(v, ioaddr + EMAC_TX_CTL1);
+}
+
+static void sun8i_dwmac_dma_stop_tx(void __iomem *ioaddr, u32 chan)
+{
+	u32 v;
+
+	v = readl(ioaddr + EMAC_TX_CTL1);
+	v &= ~EMAC_TX_DMA_EN;
+	writel(v, ioaddr + EMAC_TX_CTL1);
+}
+
+static void sun8i_dwmac_dma_start_rx(void __iomem *ioaddr, u32 chan)
+{
+	u32 v;
+
+	v = readl(ioaddr + EMAC_RX_CTL1);
+	v |= EMAC_RX_DMA_START;
+	v |= EMAC_RX_DMA_EN;
+	writel(v, ioaddr + EMAC_RX_CTL1);
+}
+
+static void sun8i_dwmac_dma_stop_rx(void __iomem *ioaddr, u32 chan)
+{
+	u32 v;
+
+	v = readl(ioaddr + EMAC_RX_CTL1);
+	v &= ~EMAC_RX_DMA_EN;
+	writel(v, ioaddr + EMAC_RX_CTL1);
+}
+
+static int sun8i_dwmac_dma_interrupt(void __iomem *ioaddr,
+				     struct stmmac_extra_stats *x, u32 chan)
+{
+	u32 v;
+	int ret = 0;
+
+	v = readl(ioaddr + EMAC_INT_STA);
+
+	if (v & EMAC_TX_INT) {
+		ret |= handle_tx;
+		x->tx_normal_irq_n++;
+	}
+
+	if (v & EMAC_TX_DMA_STOP_INT)
+		x->tx_process_stopped_irq++;
+
+	if (v & EMAC_TX_BUF_UA_INT)
+		x->tx_process_stopped_irq++;
+
+	if (v & EMAC_TX_TIMEOUT_INT)
+		ret |= tx_hard_error;
+
+	if (v & EMAC_TX_UNDERFLOW_INT) {
+		ret |= tx_hard_error;
+		x->tx_undeflow_irq++;
+	}
+
+	if (v & EMAC_TX_EARLY_INT)
+		x->tx_early_irq++;
+
+	if (v & EMAC_RX_INT) {
+		ret |= handle_rx;
+		x->rx_normal_irq_n++;
+	}
+
+	if (v & EMAC_RX_BUF_UA_INT)
+		x->rx_buf_unav_irq++;
+
+	if (v & EMAC_RX_DMA_STOP_INT)
+		x->rx_process_stopped_irq++;
+
+	if (v & EMAC_RX_TIMEOUT_INT)
+		ret |= tx_hard_error;
+
+	if (v & EMAC_RX_OVERFLOW_INT) {
+		ret |= tx_hard_error;
+		x->rx_overflow_irq++;
+	}
+
+	if (v & EMAC_RX_EARLY_INT)
+		x->rx_early_irq++;
+
+	if (v & EMAC_RGMII_STA_INT)
+		x->irq_rgmii_n++;
+
+	writel(v, ioaddr + EMAC_INT_STA);
+
+	return ret;
+}
+
+static void sun8i_dwmac_dma_operation_mode(void __iomem *ioaddr, int txmode,
+					   int rxmode, int rxfifosz)
+{
+	u32 v;
+
+	v = readl(ioaddr + EMAC_TX_CTL1);
+	if (txmode == SF_DMA_MODE) {
+		v |= EMAC_TX_MD;
+		/* Undocumented bit (called TX_NEXT_FRM in BSP), the original
+		 * comment is
+		 * "Operating on second frame increase the performance
+		 * especially when transmit store-and-forward is used."
+		 */
+		v |= EMAC_TX_NEXT_FRM;
+	} else {
+		v &= ~EMAC_TX_MD;
+		v &= ~EMAC_TX_TH_MASK;
+		if (txmode < 64)
+			v |= EMAC_TX_TH_64;
+		else if (txmode < 128)
+			v |= EMAC_TX_TH_128;
+		else if (txmode < 192)
+			v |= EMAC_TX_TH_192;
+		else if (txmode < 256)
+			v |= EMAC_TX_TH_256;
+	}
+	writel(v, ioaddr + EMAC_TX_CTL1);
+
+	v = readl(ioaddr + EMAC_RX_CTL1);
+	if (rxmode == SF_DMA_MODE) {
+		v |= EMAC_RX_MD;
+	} else {
+		v &= ~EMAC_RX_MD;
+		v &= ~EMAC_RX_TH_MASK;
+		if (rxmode < 32)
+			v |= EMAC_RX_TH_32;
+		else if (rxmode < 64)
+			v |= EMAC_RX_TH_64;
+		else if (rxmode < 96)
+			v |= EMAC_RX_TH_96;
+		else if (rxmode < 128)
+			v |= EMAC_RX_TH_128;
+	}
+	writel(v, ioaddr + EMAC_RX_CTL1);
+}
+
+static const struct stmmac_dma_ops sun8i_dwmac_dma_ops = {
+	.reset = sun8i_dwmac_dma_reset,
+	.init = sun8i_dwmac_dma_init,
+	.dump_regs = sun8i_dwmac_dump_regs,
+	.dma_mode = sun8i_dwmac_dma_operation_mode,
+	.enable_dma_transmission = sun8i_dwmac_enable_dma_transmission,
+	.enable_dma_irq = sun8i_dwmac_enable_dma_irq,
+	.disable_dma_irq = sun8i_dwmac_disable_dma_irq,
+	.start_tx = sun8i_dwmac_dma_start_tx,
+	.stop_tx = sun8i_dwmac_dma_stop_tx,
+	.start_rx = sun8i_dwmac_dma_start_rx,
+	.stop_rx = sun8i_dwmac_dma_stop_rx,
+	.dma_interrupt = sun8i_dwmac_dma_interrupt,
+};
+
+static int sun8i_dwmac_init(struct platform_device *pdev, void *priv)
+{
+	struct sunxi_priv_data *gmac = priv;
+	int ret;
+
+	if (gmac->regulator) {
+		ret = regulator_enable(gmac->regulator);
+		if (ret) {
+			dev_err(&pdev->dev, "Fail to enable regulator\n");
+			return ret;
+		}
+	}
+
+	ret = clk_prepare_enable(gmac->tx_clk);
+	if (ret) {
+		if (gmac->regulator)
+			regulator_disable(gmac->regulator);
+		dev_err(&pdev->dev, "Could not enable AHB clock\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static void sun8i_dwmac_core_init(struct mac_device_info *hw, int mtu)
+{
+	void __iomem *ioaddr = hw->pcsr;
+	u32 v;
+
+	v = (8 << EMAC_BURSTLEN_SHIFT); /* burst len */
+	writel(v, ioaddr + EMAC_BASIC_CTL1);
+}
+
+static void sun8i_dwmac_set_mac(void __iomem *ioaddr, bool enable)
+{
+	u32 t, r;
+
+	t = readl(ioaddr + EMAC_TX_CTL0);
+	r = readl(ioaddr + EMAC_RX_CTL0);
+	if (enable) {
+		t |= EMAC_TX_TRANSMITTER_EN;
+		r |= EMAC_RX_RECEIVER_EN;
+	} else {
+		t &= ~EMAC_TX_TRANSMITTER_EN;
+		r &= ~EMAC_RX_RECEIVER_EN;
+	}
+	writel(t, ioaddr + EMAC_TX_CTL0);
+	writel(r, ioaddr + EMAC_RX_CTL0);
+}
+
+/* Set MAC address at slot reg_n
+ * All slot > 0 need to be enabled with MAC_ADDR_TYPE_DST
+ * If addr is NULL, clear the slot
+ */
+static void sun8i_dwmac_set_umac_addr(struct mac_device_info *hw,
+				      unsigned char *addr,
+				      unsigned int reg_n)
+{
+	void __iomem *ioaddr = hw->pcsr;
+	u32 v;
+
+	if (!addr) {
+		writel(0, ioaddr + EMAC_MACADDR_HI(reg_n));
+		return;
+	}
+
+	stmmac_set_mac_addr(ioaddr, addr, EMAC_MACADDR_HI(reg_n),
+			    EMAC_MACADDR_LO(reg_n));
+	if (reg_n > 0) {
+		v = readl(ioaddr + EMAC_MACADDR_HI(reg_n));
+		v |= MAC_ADDR_TYPE_DST;
+		writel(v, ioaddr + EMAC_MACADDR_HI(reg_n));
+	}
+}
+
+static void sun8i_dwmac_get_umac_addr(struct mac_device_info *hw,
+				      unsigned char *addr,
+				      unsigned int reg_n)
+{
+	void __iomem *ioaddr = hw->pcsr;
+
+	stmmac_get_mac_addr(ioaddr, addr, EMAC_MACADDR_HI(reg_n),
+			    EMAC_MACADDR_LO(reg_n));
+}
+
+/* caution this function must return non 0 to work */
+static int sun8i_dwmac_rx_ipc_enable(struct mac_device_info *hw)
+{
+	void __iomem *ioaddr = hw->pcsr;
+	u32 v;
+
+	v = readl(ioaddr + EMAC_RX_CTL0);
+	v |= EMAC_RX_DO_CRC;
+	writel(v, ioaddr + EMAC_RX_CTL0);
+
+	return 1;
+}
+
+static void sun8i_dwmac_set_filter(struct mac_device_info *hw,
+				   struct net_device *dev)
+{
+	void __iomem *ioaddr = hw->pcsr;
+	u32 v;
+	int i = 1;
+	struct netdev_hw_addr *ha;
+	int macaddrs = netdev_uc_count(dev) + netdev_mc_count(dev) + 1;
+
+	v = EMAC_FRM_FLT_CTL;
+
+	if (dev->flags & IFF_PROMISC) {
+		v = EMAC_FRM_FLT_RXALL;
+	} else if (dev->flags & IFF_ALLMULTI) {
+		v |= EMAC_FRM_FLT_MULTICAST;
+	} else if (macaddrs <= hw->unicast_filter_entries) {
+		if (!netdev_mc_empty(dev)) {
+			netdev_for_each_mc_addr(ha, dev) {
+				sun8i_dwmac_set_umac_addr(hw, ha->addr, i);
+				i++;
+			}
+		}
+		if (!netdev_uc_empty(dev)) {
+			netdev_for_each_uc_addr(ha, dev) {
+				sun8i_dwmac_set_umac_addr(hw, ha->addr, i);
+				i++;
+			}
+		}
+	} else {
+		netdev_info(dev, "Too many address, switching to promiscuous\n");
+		v = EMAC_FRM_FLT_RXALL;
+	}
+
+	/* Disable unused address filter slots */
+	while (i < hw->unicast_filter_entries)
+		sun8i_dwmac_set_umac_addr(hw, NULL, i++);
+
+	writel(v, ioaddr + EMAC_RX_FRM_FLT);
+}
+
+static void sun8i_dwmac_flow_ctrl(struct mac_device_info *hw,
+				  unsigned int duplex, unsigned int fc,
+				  unsigned int pause_time, u32 tx_cnt)
+{
+	void __iomem *ioaddr = hw->pcsr;
+	u32 v;
+
+	v = readl(ioaddr + EMAC_RX_CTL0);
+	if (fc == FLOW_AUTO)
+		v |= EMAC_RX_FLOW_CTL_EN;
+	else
+		v &= ~EMAC_RX_FLOW_CTL_EN;
+	writel(v, ioaddr + EMAC_RX_CTL0);
+
+	v = readl(ioaddr + EMAC_TX_FLOW_CTL);
+	if (fc == FLOW_AUTO)
+		v |= EMAC_TX_FLOW_CTL_EN;
+	else
+		v &= ~EMAC_TX_FLOW_CTL_EN;
+	writel(v, ioaddr + EMAC_TX_FLOW_CTL);
+}
+
+static int sun8i_dwmac_reset(struct stmmac_priv *priv)
+{
+	u32 v;
+	int err;
+
+	v = readl(priv->ioaddr + EMAC_BASIC_CTL1);
+	writel(v | 0x01, priv->ioaddr + EMAC_BASIC_CTL1);
+
+	err = readl_poll_timeout(priv->ioaddr + EMAC_BASIC_CTL1, v,
+				 !(v & 0x01), 100, 10000);
+
+	if (err) {
+		dev_err(priv->device, "EMAC reset timeout\n");
+		return -EFAULT;
+	}
+	return 0;
+}
+
+static int sun8i_dwmac_set_syscon(struct stmmac_priv *priv)
+{
+	struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
+	struct device_node *node = priv->device->of_node;
+	int ret;
+	u32 reg, val;
+
+	regmap_read(gmac->regmap, SYSCON_EMAC_REG, &val);
+	reg = gmac->variant->default_syscon_value;
+	if (reg != val)
+		dev_warn(priv->device,
+			 "Current syscon value is not the default %x (expect %x)\n",
+			 val, reg);
+
+	if (gmac->variant->internal_phy) {
+		if (!gmac->use_internal_phy) {
+			/* switch to external PHY interface */
+			reg &= ~H3_EPHY_SELECT;
+		} else {
+			reg |= H3_EPHY_SELECT;
+			reg &= ~H3_EPHY_SHUTDOWN;
+			dev_dbg(priv->device, "Select internal_phy %x\n", reg);
+
+			if (of_property_read_bool(priv->plat->phy_node,
+						  "allwinner,leds-active-low"))
+				reg |= H3_EPHY_LED_POL;
+			else
+				reg &= ~H3_EPHY_LED_POL;
+
+			ret = of_mdio_parse_addr(priv->device,
+						 priv->plat->phy_node);
+			if (ret < 0) {
+				dev_err(priv->device, "Could not parse MDIO addr\n");
+				return ret;
+			}
+			/* of_mdio_parse_addr returns a valid (0 ~ 31) PHY
+			 * address. No need to mask it again.
+			 */
+			reg |= ret << H3_EPHY_ADDR_SHIFT;
+		}
+	}
+
+	if (!of_property_read_u32(node, "allwinner,tx-delay-ps", &val)) {
+		if (val % 100) {
+			dev_err(priv->device, "tx-delay must be a multiple of 100\n");
+			return -EINVAL;
+		}
+		val /= 100;
+		dev_dbg(priv->device, "set tx-delay to %x\n", val);
+		if (val <= SYSCON_ETXDC_MASK) {
+			reg &= ~(SYSCON_ETXDC_MASK << SYSCON_ETXDC_SHIFT);
+			reg |= (val << SYSCON_ETXDC_SHIFT);
+		} else {
+			dev_err(priv->device, "Invalid TX clock delay: %d\n",
+				val);
+			return -EINVAL;
+		}
+	}
+
+	if (!of_property_read_u32(node, "allwinner,rx-delay-ps", &val)) {
+		if (val % 100) {
+			dev_err(priv->device, "rx-delay must be a multiple of 100\n");
+			return -EINVAL;
+		}
+		val /= 100;
+		dev_dbg(priv->device, "set rx-delay to %x\n", val);
+		if (val <= SYSCON_ERXDC_MASK) {
+			reg &= ~(SYSCON_ERXDC_MASK << SYSCON_ERXDC_SHIFT);
+			reg |= (val << SYSCON_ERXDC_SHIFT);
+		} else {
+			dev_err(priv->device, "Invalid RX clock delay: %d\n",
+				val);
+			return -EINVAL;
+		}
+	}
+
+	/* Clear interface mode bits */
+	reg &= ~(SYSCON_ETCS_MASK | SYSCON_EPIT);
+	if (gmac->variant->support_rmii)
+		reg &= ~SYSCON_RMII_EN;
+
+	switch (priv->plat->interface) {
+	case PHY_INTERFACE_MODE_MII:
+		/* default */
+		break;
+	case PHY_INTERFACE_MODE_RGMII:
+		reg |= SYSCON_EPIT | SYSCON_ETCS_INT_GMII;
+		break;
+	case PHY_INTERFACE_MODE_RMII:
+		reg |= SYSCON_RMII_EN | SYSCON_ETCS_EXT_GMII;
+		break;
+	default:
+		dev_err(priv->device, "Unsupported interface mode: %s",
+			phy_modes(priv->plat->interface));
+		return -EINVAL;
+	}
+
+	regmap_write(gmac->regmap, SYSCON_EMAC_REG, reg);
+
+	return 0;
+}
+
+static void sun8i_dwmac_unset_syscon(struct sunxi_priv_data *gmac)
+{
+	u32 reg = gmac->variant->default_syscon_value;
+
+	regmap_write(gmac->regmap, SYSCON_EMAC_REG, reg);
+}
+
+static int sun8i_dwmac_power_internal_phy(struct stmmac_priv *priv)
+{
+	struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
+	int ret;
+
+	if (!gmac->use_internal_phy)
+		return 0;
+
+	ret = clk_prepare_enable(gmac->ephy_clk);
+	if (ret) {
+		dev_err(priv->device, "Cannot enable ephy\n");
+		return ret;
+	}
+
+	ret = reset_control_deassert(gmac->rst_ephy);
+	if (ret) {
+		dev_err(priv->device, "Cannot deassert ephy\n");
+		clk_disable_unprepare(gmac->ephy_clk);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int sun8i_dwmac_unpower_internal_phy(struct sunxi_priv_data *gmac)
+{
+	if (!gmac->use_internal_phy)
+		return 0;
+
+	clk_disable_unprepare(gmac->ephy_clk);
+	reset_control_assert(gmac->rst_ephy);
+	return 0;
+}
+
+static int sun8i_power_phy(struct stmmac_priv *priv)
+{
+	struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
+	int ret;
+
+	ret = sun8i_dwmac_power_internal_phy(priv);
+	if (ret)
+		return ret;
+
+	ret = sun8i_dwmac_set_syscon(priv);
+	if (ret)
+		goto error_phy;
+
+	ret = sun8i_dwmac_reset(priv);
+	if (ret)
+		goto error_phy;
+	return 0;
+
+error_phy:
+	sun8i_dwmac_unset_syscon(gmac);
+	sun8i_dwmac_unpower_internal_phy(gmac);
+	return ret;
+}
+
+static void sun8i_unpower_phy(struct sunxi_priv_data *gmac)
+{
+	sun8i_dwmac_unset_syscon(gmac);
+	sun8i_dwmac_unpower_internal_phy(gmac);
+}
+
+static void sun8i_dwmac_exit(struct platform_device *pdev, void *priv)
+{
+	struct sunxi_priv_data *gmac = priv;
+
+	sun8i_unpower_phy(gmac);
+
+	clk_disable_unprepare(gmac->tx_clk);
+
+	if (gmac->regulator)
+		regulator_disable(gmac->regulator);
+}
+
+static const struct stmmac_ops sun8i_dwmac_ops = {
+	.core_init = sun8i_dwmac_core_init,
+	.set_mac = sun8i_dwmac_set_mac,
+	.dump_regs = sun8i_dwmac_dump_mac_regs,
+	.rx_ipc = sun8i_dwmac_rx_ipc_enable,
+	.set_filter = sun8i_dwmac_set_filter,
+	.flow_ctrl = sun8i_dwmac_flow_ctrl,
+	.set_umac_addr = sun8i_dwmac_set_umac_addr,
+	.get_umac_addr = sun8i_dwmac_get_umac_addr,
+};
+
+static struct mac_device_info *sun8i_dwmac_setup(void *ppriv)
+{
+	struct mac_device_info *mac;
+	struct stmmac_priv *priv = ppriv;
+	int ret;
+
+	mac = devm_kzalloc(priv->device, sizeof(*mac), GFP_KERNEL);
+	if (!mac)
+		return NULL;
+
+	ret = sun8i_power_phy(priv);
+	if (ret)
+		return NULL;
+
+	mac->pcsr = priv->ioaddr;
+	mac->mac = &sun8i_dwmac_ops;
+	mac->dma = &sun8i_dwmac_dma_ops;
+
+	mac->link.port = 0;
+	mac->link.duplex = BIT(0);
+	mac->link.speed = 1;
+	mac->mii.addr = EMAC_MDIO_CMD;
+	mac->mii.data = EMAC_MDIO_DATA;
+	mac->mii.reg_shift = 4;
+	mac->mii.reg_mask = GENMASK(8, 4);
+	mac->mii.addr_shift = 12;
+	mac->mii.addr_mask = GENMASK(16, 12);
+	mac->mii.clk_csr_shift = 20;
+	mac->mii.clk_csr_mask = GENMASK(22, 20);
+	mac->unicast_filter_entries = 8;
+
+	/* Synopsys Id is not available */
+	priv->synopsys_id = 0;
+
+	return mac;
+}
+
+static int sun8i_dwmac_probe(struct platform_device *pdev)
+{
+	struct plat_stmmacenet_data *plat_dat;
+	struct stmmac_resources stmmac_res;
+	struct sunxi_priv_data *gmac;
+	struct device *dev = &pdev->dev;
+	int ret;
+
+	ret = stmmac_get_platform_resources(pdev, &stmmac_res);
+	if (ret)
+		return ret;
+
+	plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac);
+	if (IS_ERR(plat_dat))
+		return PTR_ERR(plat_dat);
+
+	gmac = devm_kzalloc(dev, sizeof(*gmac), GFP_KERNEL);
+	if (!gmac)
+		return -ENOMEM;
+
+	gmac->variant = of_device_get_match_data(&pdev->dev);
+	if (!gmac->variant) {
+		dev_err(&pdev->dev, "Missing dwmac-sun8i variant\n");
+		return -EINVAL;
+	}
+
+	gmac->tx_clk = devm_clk_get(dev, "stmmaceth");
+	if (IS_ERR(gmac->tx_clk)) {
+		dev_err(dev, "Could not get TX clock\n");
+		return PTR_ERR(gmac->tx_clk);
+	}
+
+	/* Optional regulator for PHY */
+	gmac->regulator = devm_regulator_get_optional(dev, "phy");
+	if (IS_ERR(gmac->regulator)) {
+		if (PTR_ERR(gmac->regulator) == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
+		dev_info(dev, "No regulator found\n");
+		gmac->regulator = NULL;
+	}
+
+	gmac->regmap = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
+						       "syscon");
+	if (IS_ERR(gmac->regmap)) {
+		ret = PTR_ERR(gmac->regmap);
+		dev_err(&pdev->dev, "Unable to map syscon: %d\n", ret);
+		return ret;
+	}
+
+	plat_dat->interface = of_get_phy_mode(dev->of_node);
+	if (plat_dat->interface == gmac->variant->internal_phy) {
+		dev_info(&pdev->dev, "Will use internal PHY\n");
+		gmac->use_internal_phy = true;
+		gmac->ephy_clk = of_clk_get(plat_dat->phy_node, 0);
+		if (IS_ERR(gmac->ephy_clk)) {
+			ret = PTR_ERR(gmac->ephy_clk);
+			dev_err(&pdev->dev, "Cannot get EPHY clock: %d\n", ret);
+			return -EINVAL;
+		}
+
+		gmac->rst_ephy = of_reset_control_get(plat_dat->phy_node, NULL);
+		if (IS_ERR(gmac->rst_ephy)) {
+			ret = PTR_ERR(gmac->rst_ephy);
+			if (ret == -EPROBE_DEFER)
+				return ret;
+			dev_err(&pdev->dev, "No EPHY reset control found %d\n",
+				ret);
+			return -EINVAL;
+		}
+	} else {
+		dev_info(&pdev->dev, "Will use external PHY\n");
+		gmac->use_internal_phy = false;
+	}
+
+	/* platform data specifying hardware features and callbacks.
+	 * hardware features were copied from Allwinner drivers.
+	 */
+	plat_dat->rx_coe = STMMAC_RX_COE_TYPE2;
+	plat_dat->tx_coe = 1;
+	plat_dat->has_sun8i = true;
+	plat_dat->bsp_priv = gmac;
+	plat_dat->init = sun8i_dwmac_init;
+	plat_dat->exit = sun8i_dwmac_exit;
+	plat_dat->setup = sun8i_dwmac_setup;
+
+	ret = sun8i_dwmac_init(pdev, plat_dat->bsp_priv);
+	if (ret)
+		return ret;
+
+	ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
+	if (ret)
+		sun8i_dwmac_exit(pdev, plat_dat->bsp_priv);
+
+	return ret;
+}
+
+static const struct of_device_id sun8i_dwmac_match[] = {
+	{ .compatible = "allwinner,sun8i-h3-emac",
+		.data = &emac_variant_h3 },
+	{ .compatible = "allwinner,sun8i-a83t-emac",
+		.data = &emac_variant_a83t },
+	{ .compatible = "allwinner,sun50i-a64-emac",
+		.data = &emac_variant_a64 },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, sun8i_dwmac_match);
+
+static struct platform_driver sun8i_dwmac_driver = {
+	.probe  = sun8i_dwmac_probe,
+	.remove = stmmac_pltfr_remove,
+	.driver = {
+		.name           = "dwmac-sun8i",
+		.pm		= &stmmac_pltfr_pm_ops,
+		.of_match_table = sun8i_dwmac_match,
+	},
+};
+module_platform_driver(sun8i_dwmac_driver);
+
+MODULE_AUTHOR("Corentin Labbe <clabbe.montjoie@gmail.com>");
+MODULE_DESCRIPTION("Allwinner sun8i DWMAC specific glue layer");
+MODULE_LICENSE("GPL");
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index b82ab64..39777a7 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -235,6 +235,17 @@ static void stmmac_clk_csr_set(struct stmmac_priv *priv)
 		else if ((clk_rate >= CSR_F_250M) && (clk_rate < CSR_F_300M))
 			priv->clk_csr = STMMAC_CSR_250_300M;
 	}
+
+	if (priv->plat->has_sun8i) {
+		if (clk_rate > 160000000)
+			priv->clk_csr = 0x03;
+		else if (clk_rate > 80000000)
+			priv->clk_csr = 0x02;
+		else if (clk_rate > 40000000)
+			priv->clk_csr = 0x01;
+		else
+			priv->clk_csr = 0;
+	}
 }
 
 static void print_pkt(unsigned char *buf, int len)
@@ -784,6 +795,14 @@ static void stmmac_adjust_link(struct net_device *dev)
 	if (phydev->link) {
 		u32 ctrl = readl(priv->ioaddr + MAC_CTRL_REG);
 
+		/* dwmac-sun8i handle loopback in MAC_CTRL_REG */
+		if (priv->plat->has_sun8i) {
+			if (dev->features & NETIF_F_LOOPBACK)
+				ctrl |= BIT(1);
+			else
+				ctrl &= ~BIT(1);
+		}
+
 		/* Now we make sure that we can be in full duplex mode.
 		 * If not, we operate in half-duplex mode. */
 		if (phydev->duplex != priv->oldduplex) {
@@ -800,6 +819,8 @@ static void stmmac_adjust_link(struct net_device *dev)
 
 		if (phydev->speed != priv->speed) {
 			new_state = 1;
+			if (priv->plat->has_sun8i)
+				ctrl &= ~GENMASK(3, 2);
 			switch (phydev->speed) {
 			case 1000:
 				if (priv->plat->has_gmac ||
@@ -811,6 +832,8 @@ static void stmmac_adjust_link(struct net_device *dev)
 				    priv->plat->has_gmac4) {
 					ctrl |= priv->hw->link.port;
 					ctrl |= priv->hw->link.speed;
+				} else if (priv->plat->has_sun8i) {
+					ctrl |= 3 << 2;
 				} else {
 					ctrl &= ~priv->hw->link.port;
 				}
@@ -820,6 +843,8 @@ static void stmmac_adjust_link(struct net_device *dev)
 				    priv->plat->has_gmac4) {
 					ctrl |= priv->hw->link.port;
 					ctrl &= ~(priv->hw->link.speed);
+				} else if (priv->plat->has_sun8i) {
+					ctrl |= 2 << 2;
 				} else {
 					ctrl &= ~priv->hw->link.port;
 				}
@@ -3969,6 +3994,10 @@ static int stmmac_hw_init(struct stmmac_priv *priv)
 
 	priv->hw = mac;
 
+	/* dwmac-sun8i only work in chain mode */
+	if (priv->plat->has_sun8i)
+		chain_mode = 1;
+
 	/* To use the chained or ring mode */
 	if (priv->synopsys_id >= DWMAC_CORE_4_00) {
 		priv->hw->mode = &dwmac4_ring_mode_ops;
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
index 7fc3a1e..3840529 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
@@ -309,6 +309,12 @@ static int stmmac_dt_phy(struct plat_stmmacenet_data *plat,
 			 struct device_node *np, struct device *dev)
 {
 	bool mdio = true;
+	static const struct of_device_id need_mdio_ids[] = {
+		{ .compatible = "snps,dwc-qos-ethernet-4.10" },
+		{ .compatible = "allwinner,sun8i-a83t-emac" },
+		{ .compatible = "allwinner,sun8i-h3-emac" },
+		{ .compatible = "allwinner,sun50i-a64-emac" },
+	};
 
 	/* If phy-handle property is passed from DT, use it as the PHY */
 	plat->phy_node = of_parse_phandle(np, "phy-handle", 0);
@@ -325,8 +331,7 @@ static int stmmac_dt_phy(struct plat_stmmacenet_data *plat,
 		mdio = false;
 	}
 
-	/* exception for dwmac-dwc-qos-eth glue logic */
-	if (of_device_is_compatible(np, "snps,dwc-qos-ethernet-4.10")) {
+	if (of_match_node(need_mdio_ids, np)) {
 		plat->mdio_node = of_get_child_by_name(np, "mdio");
 	} else {
 		/**
diff --git a/include/linux/stmmac.h b/include/linux/stmmac.h
index 8bb550b..108739f 100644
--- a/include/linux/stmmac.h
+++ b/include/linux/stmmac.h
@@ -186,6 +186,7 @@ struct plat_stmmacenet_data {
 	struct reset_control *stmmac_rst;
 	struct stmmac_axi *axi;
 	int has_gmac4;
+	bool has_sun8i;
 	bool tso_en;
 	int mac_port_sel_speed;
 	bool en_tx_lpi_clockgating;
-- 
2.10.2

  parent reply	other threads:[~2017-05-01 12:49 UTC|newest]

Thread overview: 29+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2017-05-01 12:45 [PATCH v5 00/20] net-next: stmmac: add dwmac-sun8i ethernet driver Corentin Labbe
2017-05-01 12:45 ` [PATCH v5 01/20] net: stmmac: export stmmac_set_mac_addr/stmmac_get_mac_addr Corentin Labbe
2017-05-01 12:45 ` [PATCH v5 02/20] net: stmmac: add optional setup function Corentin Labbe
2017-05-01 12:45 ` [PATCH v5 03/20] dt-bindings: net: Add DT bindings documentation for Allwinner dwmac-sun8i Corentin Labbe
2017-05-01 13:45   ` Andrew Lunn
2017-05-01 12:45 ` [PATCH v5 04/20] dt-bindings: syscon: Add DT bindings documentation for Allwinner syscon Corentin Labbe
2017-05-05 20:20   ` Rob Herring
2017-05-01 12:45 ` Corentin Labbe [this message]
2017-05-01 12:45 ` [PATCH v5 06/20] arm: sun8i: sunxi-h3-h5: Add dt node for the syscon control module Corentin Labbe
2017-05-01 12:45 ` [PATCH v5 07/20] arm: sun8i: sunxi-h3-h5: add dwmac-sun8i ethernet driver Corentin Labbe
2017-05-01 12:45 ` [PATCH v5 08/20] arm: sun8i: orangepi-pc: Enable dwmac-sun8i Corentin Labbe
2017-05-01 12:45 ` [PATCH v5 09/20] arm: sun8i: orangepi-zero: " Corentin Labbe
2017-05-01 12:45 ` [PATCH v5 10/20] arm: sun8i: orangepi-one: " Corentin Labbe
2017-05-01 12:45 ` [PATCH v5 11/20] arm: sun8i: orangepi-2: " Corentin Labbe
2017-05-01 12:45 ` [PATCH v5 12/20] arm: sun8i: orangepi-pc-plus: Set EMAC activity LEDs to active high Corentin Labbe
2017-05-01 12:45 ` [PATCH v5 13/20] arm64: allwinner: sun50i-a64: Add dt node for the syscon control module Corentin Labbe
2017-05-01 12:45 ` [PATCH v5 14/20] arm64: allwinner: sun50i-a64: add dwmac-sun8i Ethernet driver Corentin Labbe
2017-05-01 12:45 ` [PATCH v5 15/20] arm64: allwinner: pine64: Enable dwmac-sun8i Corentin Labbe
2017-05-01 12:45 ` [PATCH v5 16/20] arm64: allwinner: pine64-plus: " Corentin Labbe
2017-05-01 12:45 ` [PATCH v5 17/20] arm64: allwinner: bananapi-m64: " Corentin Labbe
2017-05-01 12:45 ` [PATCH v5 18/20] arm: sunxi: Enable dwmac-sun8i driver on sunxi_defconfig Corentin Labbe
2017-05-01 12:45 ` [PATCH v5 19/20] arm: multi_v7: Enable dwmac-sun8i driver on multi_v7_defconfig Corentin Labbe
2017-05-01 12:45 ` [PATCH v5 20/20] arm64: defconfig: Enable dwmac-sun8i driver on defconfig Corentin Labbe
2017-05-01 14:01 ` [PATCH v5 00/20] net-next: stmmac: add dwmac-sun8i ethernet driver Andrew Lunn
2017-05-01 14:28   ` Chen-Yu Tsai
2017-05-01 14:45     ` Andrew Lunn
2017-05-01 15:58       ` Corentin Labbe
2017-05-01 16:10         ` Andrew Lunn
2017-05-05 12:13 ` Corentin Labbe

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20170501124520.3769-6-clabbe.montjoie@gmail.com \
    --to=clabbe.montjoie@gmail.com \
    --cc=alexandre.torgue@st.com \
    --cc=catalin.marinas@arm.com \
    --cc=devicetree@vger.kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux@armlinux.org.uk \
    --cc=mark.rutland@arm.com \
    --cc=maxime.ripard@free-electrons.com \
    --cc=netdev@vger.kernel.org \
    --cc=peppe.cavallaro@st.com \
    --cc=robh+dt@kernel.org \
    --cc=wens@csie.org \
    --cc=will.deacon@arm.com \
    --subject='Re: [PATCH v5 05/20] net: stmmac: Add dwmac-sun8i' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).