* [PATCH 0/2 v6] Lattice MachXO2 Slave SPI FPGA Manager support @ 2018-03-16 15:54 Paolo Pisati 2018-03-16 15:54 ` [PATCH 1/2] dt: bindings: fpga: add lattice machxo2 slave spi binding description Paolo Pisati 2018-03-16 15:54 ` [PATCH 2/2] fpga: lattice machxo2: Add Lattice MachXO2 support Paolo Pisati 0 siblings, 2 replies; 12+ messages in thread From: Paolo Pisati @ 2018-03-16 15:54 UTC (permalink / raw) To: Alan Tull, Moritz Fischer, Rob Herring, Mark Rutland Cc: linux-fpga, devicetree, linux-kernel Hi all, this series adds support for the Lattice MachXO2 FPGA chip, programmed over Slave SPI. Tested on a raspberry pi3, beaglebone black (little endian mode) and imx6 hummingboard (big endian mode) + bugblat's pif2 fpga hat (machxo2 7000HC) or tinyfpga A1/A2 (machxo2 256HC / 1200HC), in SPI slave mode with varying bus speed. Changes since v5: * fixed all the endianess issues * introduced a cleanup() path invoked in case of flash failure * moved back machxo2_write() to use a spi_sync() transaction per line write (in v5 i queued all the spi_write()s and executed a single spi_sync() at the end, but that, sometimes, resulted in the REFRESH command to fail with a CMD_ERR, depending on the SPI bus speed) Paolo Pisati (2): dt: bindings: fpga: add lattice machxo2 slave spi binding description fpga: lattice machxo2: Add Lattice MachXO2 support .../bindings/fpga/lattice-machxo2-spi.txt | 29 ++ drivers/fpga/Kconfig | 8 + drivers/fpga/Makefile | 1 + drivers/fpga/machxo2-spi.c | 410 +++++++++++++++++++++ 4 files changed, 448 insertions(+) create mode 100644 Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt create mode 100644 drivers/fpga/machxo2-spi.c -- 2.7.4 ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 1/2] dt: bindings: fpga: add lattice machxo2 slave spi binding description 2018-03-16 15:54 [PATCH 0/2 v6] Lattice MachXO2 Slave SPI FPGA Manager support Paolo Pisati @ 2018-03-16 15:54 ` Paolo Pisati 2018-03-16 16:31 ` Moritz Fischer 2018-03-16 15:54 ` [PATCH 2/2] fpga: lattice machxo2: Add Lattice MachXO2 support Paolo Pisati 1 sibling, 1 reply; 12+ messages in thread From: Paolo Pisati @ 2018-03-16 15:54 UTC (permalink / raw) To: Alan Tull, Moritz Fischer, Rob Herring, Mark Rutland Cc: linux-fpga, devicetree, linux-kernel Add dt binding documentation details for Lattice MachXO2 FPGA configuration over Slave SPI interface. Signed-off-by: Paolo Pisati <p.pisati@gmail.com> Acked-by: Rob Herring <robh@kernel.org> --- .../bindings/fpga/lattice-machxo2-spi.txt | 29 ++++++++++++++++++++++ 1 file changed, 29 insertions(+) create mode 100644 Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt diff --git a/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt b/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt new file mode 100644 index 0000000..a8c362e --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt @@ -0,0 +1,29 @@ +Lattice MachXO2 Slave SPI FPGA Manager + +Lattice MachXO2 FPGAs support a method of loading the bitstream over +'slave SPI' interface. + +See 'MachXO2ProgrammingandConfigurationUsageGuide.pdf' on www.latticesemi.com + +Required properties: +- compatible: should contain "lattice,machxo2-slave-spi" +- reg: spi chip select of the FPGA + +Example for full FPGA configuration: + + fpga-region0 { + compatible = "fpga-region"; + fpga-mgr = <&fpga_mgr_spi>; + #address-cells = <0x1>; + #size-cells = <0x1>; + }; + + spi1: spi@2000 { + ... + + fpga_mgr_spi: fpga-mgr@0 { + compatible = "lattice,machxo2-slave-spi"; + spi-max-frequency = <8000000>; + reg = <0>; + }; + }; -- 2.7.4 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [PATCH 1/2] dt: bindings: fpga: add lattice machxo2 slave spi binding description 2018-03-16 15:54 ` [PATCH 1/2] dt: bindings: fpga: add lattice machxo2 slave spi binding description Paolo Pisati @ 2018-03-16 16:31 ` Moritz Fischer 2018-03-19 15:42 ` Alan Tull 0 siblings, 1 reply; 12+ messages in thread From: Moritz Fischer @ 2018-03-16 16:31 UTC (permalink / raw) To: Paolo Pisati Cc: Alan Tull, Moritz Fischer, Rob Herring, Mark Rutland, linux-fpga, devicetree, linux-kernel On Fri, Mar 16, 2018 at 04:54:28PM +0100, Paolo Pisati wrote: > Add dt binding documentation details for Lattice MachXO2 FPGA configuration > over Slave SPI interface. > > Signed-off-by: Paolo Pisati <p.pisati@gmail.com> > Acked-by: Rob Herring <robh@kernel.org> Acked-by: Moritz Fischer <mdf@kernel.org> > --- > .../bindings/fpga/lattice-machxo2-spi.txt | 29 ++++++++++++++++++++++ > 1 file changed, 29 insertions(+) > create mode 100644 Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt > > diff --git a/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt b/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt > new file mode 100644 > index 0000000..a8c362e > --- /dev/null > +++ b/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt > @@ -0,0 +1,29 @@ > +Lattice MachXO2 Slave SPI FPGA Manager > + > +Lattice MachXO2 FPGAs support a method of loading the bitstream over > +'slave SPI' interface. Nit: a 'slave SPI' > + > +See 'MachXO2ProgrammingandConfigurationUsageGuide.pdf' on www.latticesemi.com > + > +Required properties: > +- compatible: should contain "lattice,machxo2-slave-spi" > +- reg: spi chip select of the FPGA > + > +Example for full FPGA configuration: > + > + fpga-region0 { > + compatible = "fpga-region"; > + fpga-mgr = <&fpga_mgr_spi>; > + #address-cells = <0x1>; > + #size-cells = <0x1>; > + }; > + > + spi1: spi@2000 { > + ... > + > + fpga_mgr_spi: fpga-mgr@0 { > + compatible = "lattice,machxo2-slave-spi"; > + spi-max-frequency = <8000000>; > + reg = <0>; > + }; > + }; > -- > 2.7.4 > Thanks, Moritz ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 1/2] dt: bindings: fpga: add lattice machxo2 slave spi binding description 2018-03-16 16:31 ` Moritz Fischer @ 2018-03-19 15:42 ` Alan Tull 0 siblings, 0 replies; 12+ messages in thread From: Alan Tull @ 2018-03-19 15:42 UTC (permalink / raw) To: Moritz Fischer Cc: Paolo Pisati, Rob Herring, Mark Rutland, linux-fpga, open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS, linux-kernel On Fri, Mar 16, 2018 at 11:31 AM, Moritz Fischer <mdf@kernel.org> wrote: > On Fri, Mar 16, 2018 at 04:54:28PM +0100, Paolo Pisati wrote: >> Add dt binding documentation details for Lattice MachXO2 FPGA configuration >> over Slave SPI interface. >> >> Signed-off-by: Paolo Pisati <p.pisati@gmail.com> >> Acked-by: Rob Herring <robh@kernel.org> > Acked-by: Moritz Fischer <mdf@kernel.org> Acked-by: Alan Tull <atull@kernel.org> Thanks, Alan >> --- >> .../bindings/fpga/lattice-machxo2-spi.txt | 29 ++++++++++++++++++++++ >> 1 file changed, 29 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt >> >> diff --git a/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt b/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt >> new file mode 100644 >> index 0000000..a8c362e >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt >> @@ -0,0 +1,29 @@ >> +Lattice MachXO2 Slave SPI FPGA Manager >> + >> +Lattice MachXO2 FPGAs support a method of loading the bitstream over >> +'slave SPI' interface. > Nit: a 'slave SPI' >> + >> +See 'MachXO2ProgrammingandConfigurationUsageGuide.pdf' on www.latticesemi.com >> + >> +Required properties: >> +- compatible: should contain "lattice,machxo2-slave-spi" >> +- reg: spi chip select of the FPGA >> + >> +Example for full FPGA configuration: >> + >> + fpga-region0 { >> + compatible = "fpga-region"; >> + fpga-mgr = <&fpga_mgr_spi>; >> + #address-cells = <0x1>; >> + #size-cells = <0x1>; >> + }; >> + >> + spi1: spi@2000 { >> + ... >> + >> + fpga_mgr_spi: fpga-mgr@0 { >> + compatible = "lattice,machxo2-slave-spi"; >> + spi-max-frequency = <8000000>; >> + reg = <0>; >> + }; >> + }; >> -- >> 2.7.4 >> > > Thanks, > > Moritz ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 2/2] fpga: lattice machxo2: Add Lattice MachXO2 support 2018-03-16 15:54 [PATCH 0/2 v6] Lattice MachXO2 Slave SPI FPGA Manager support Paolo Pisati 2018-03-16 15:54 ` [PATCH 1/2] dt: bindings: fpga: add lattice machxo2 slave spi binding description Paolo Pisati @ 2018-03-16 15:54 ` Paolo Pisati 2018-03-16 16:26 ` Moritz Fischer 1 sibling, 1 reply; 12+ messages in thread From: Paolo Pisati @ 2018-03-16 15:54 UTC (permalink / raw) To: Alan Tull, Moritz Fischer, Rob Herring, Mark Rutland Cc: linux-fpga, devicetree, linux-kernel This patch adds support to the FPGA manager for programming MachXO2 device’s internal flash memory, via slave SPI. Signed-off-by: Paolo Pisati <p.pisati@gmail.com> --- drivers/fpga/Kconfig | 8 + drivers/fpga/Makefile | 1 + drivers/fpga/machxo2-spi.c | 410 +++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 419 insertions(+) create mode 100644 drivers/fpga/machxo2-spi.c diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig index ad5448f..65ccbc5 100644 --- a/drivers/fpga/Kconfig +++ b/drivers/fpga/Kconfig @@ -38,6 +38,14 @@ config FPGA_MGR_ALTERA_PS_SPI FPGA manager driver support for Altera Arria/Cyclone/Stratix using the passive serial interface over SPI. +config FPGA_MGR_MACHXO2_SPI + tristate "Lattice MachXO2 SPI" + depends on SPI + help + FPGA manager driver support for Lattice MachXO2 configuration + over slave SPI interface. + + config FPGA_MGR_SOCFPGA tristate "Altera SOCFPGA FPGA Manager" depends on ARCH_SOCFPGA || COMPILE_TEST diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile index f98dcf1..38abb08 100644 --- a/drivers/fpga/Makefile +++ b/drivers/fpga/Makefile @@ -10,6 +10,7 @@ obj-$(CONFIG_FPGA) += fpga-mgr.o obj-$(CONFIG_FPGA_MGR_ALTERA_CVP) += altera-cvp.o obj-$(CONFIG_FPGA_MGR_ALTERA_PS_SPI) += altera-ps-spi.o obj-$(CONFIG_FPGA_MGR_ICE40_SPI) += ice40-spi.o +obj-$(CONFIG_FPGA_MGR_MACHXO2_SPI) += machxo2-spi.o obj-$(CONFIG_FPGA_MGR_SOCFPGA) += socfpga.o obj-$(CONFIG_FPGA_MGR_SOCFPGA_A10) += socfpga-a10.o obj-$(CONFIG_FPGA_MGR_TS73XX) += ts73xx-fpga.o diff --git a/drivers/fpga/machxo2-spi.c b/drivers/fpga/machxo2-spi.c new file mode 100644 index 0000000..3c7fc3e --- /dev/null +++ b/drivers/fpga/machxo2-spi.c @@ -0,0 +1,410 @@ +/** + * Lattice MachXO2 Slave SPI Driver + * + * Copyright (C) 2018 Paolo Pisati <p.pisati@gmail.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * Manage Lattice FPGA firmware that is loaded over SPI using + * the slave serial configuration interface. + */ + +#include <linux/delay.h> +#include <linux/fpga/fpga-mgr.h> +#include <linux/gpio/consumer.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/spi/spi.h> + +//#define MACHXO2_DEBUG + +/* MachXO2 Programming Guide - sysCONFIG Programming Commands */ +#define IDCODE_PUB {0xe0, 0x00, 0x00, 0x00} +#define ISC_ENABLE {0xc6, 0x08, 0x00, 0x00} +#define ISC_ERASE {0x0e, 0x04, 0x00, 0x00} +#define ISC_PROGRAMDONE {0x5e, 0x00, 0x00, 0x00} +#define LSC_INITADDRESS {0x46, 0x00, 0x00, 0x00} +#define LSC_PROGINCRNV {0x70, 0x00, 0x00, 0x01} +#define LSC_READ_STATUS {0x3c, 0x00, 0x00, 0x00} +#define LSC_REFRESH {0x79, 0x00, 0x00, 0x00} + +/* + * Max CCLK in Slave SPI mode according to 'MachXO2 Family Data + * Sheet' sysCONFIG Port Timing Specifications (3-36) + */ +#define MACHXO2_MAX_SPEED 66000000 + +#define MACHXO2_LOW_DELAY 5 /* us */ +#define MACHXO2_HIGH_DELAY 200 /* us */ +#define MACHXO2_REFRESH 4800 /* us */ +#define MACHXO2_MAX_BUSY_LOOP 128 +#define MACHXO2_MAX_REFRESH_LOOP 16 + +#define MACHXO2_PAGE_SIZE 16 +#define MACHXO2_BUF_SIZE (MACHXO2_PAGE_SIZE + 4) + +/* Status register bits, errors and error mask */ +#define BUSY 12 +#define DONE 8 +#define DVER 27 +#define ENAB 9 +#define ERRBITS 23 +#define ERRMASK 7 +#define FAIL 13 + +#define ENOERR 0 /* no error */ +#define EID 1 +#define ECMD 2 +#define ECRC 3 +#define EPREAM 4 /* preamble error */ +#define EABRT 5 /* abort error */ +#define EOVERFL 6 /* overflow error */ +#define ESDMEOF 7 /* SDM EOF */ + +static inline u8 get_err(unsigned long *status) +{ + return (*status >> ERRBITS) & ERRMASK; +} + +static int get_status(struct spi_device *spi, unsigned long *status) +{ + struct spi_message msg; + struct spi_transfer rx, tx; + u8 cmd[] = LSC_READ_STATUS; + int ret; + + memset(&rx, 0, sizeof(rx)); + memset(&tx, 0, sizeof(tx)); + tx.tx_buf = cmd; + tx.len = sizeof(cmd); + rx.rx_buf = status; + rx.len = 4; + spi_message_init(&msg); + spi_message_add_tail(&tx, &msg); + spi_message_add_tail(&rx, &msg); + ret = spi_sync(spi, &msg); + if (ret) + return ret; + + *status = be32_to_cpu(*status); + return 0; +} + +#ifdef MACHXO2_DEBUG +static void dump_status_reg(unsigned long *status) +{ + char *ferr; + + switch (get_err(status)) { + case ENOERR: + ferr = "No Error"; + break; + case EID: + ferr = "ID ERR"; + break; + case ECMD: + ferr = "CMD ERR"; + break; + case ECRC: + ferr = "CRC ERR"; + break; + case EPREAM: + ferr = "Preamble ERR"; + break; + case EABRT: + ferr = "Abort ERR"; + break; + case EOVERFL: + ferr = "Overflow ERR"; + break; + case ESDMEOF: + ferr = "SDM EOF"; + break; + default: + ferr = "Default switch case"; + } + printk(KERN_DEBUG "machxo2 status: 0x%08lX - done=%d, cfgena=%d, busy=%d, fail=%d, devver=%d, err=%s\n", + *status, test_bit(DONE, status), test_bit(ENAB, status), + test_bit(BUSY, status), test_bit(FAIL, status), + test_bit(DVER, status), ferr); +} +#else +static void dump_status_reg(unsigned long *status) {} +#endif + +static int wait_until_not_busy(struct spi_device *spi) +{ + unsigned long status; + int ret, loop = 0; + + do { + ret = get_status(spi, &status); + if (ret) + break; + if (++loop >= MACHXO2_MAX_BUSY_LOOP) { + ret = -EBUSY; + break; + } + } while (test_bit(BUSY, &status)); + + return ret; +} + +static int machxo2_cleanup(struct fpga_manager *mgr) +{ + struct spi_device *spi = mgr->priv; + struct spi_message msg; + struct spi_transfer tx[2]; + u8 erase[] = ISC_ERASE; + u8 refresh[] = LSC_REFRESH; + int ret; + + memset(tx, 0, sizeof(tx)); + spi_message_init(&msg); + tx[0].tx_buf = &erase; + tx[0].len = sizeof(erase); + spi_message_add_tail(&tx[0], &msg); + ret = spi_sync(spi, &msg); + if (ret) + goto fail; + + ret = wait_until_not_busy(spi); + if (ret) + goto fail; + + spi_message_init(&msg); + tx[1].tx_buf = &refresh; + tx[1].len = sizeof(refresh); + tx[1].delay_usecs = MACHXO2_REFRESH; + spi_message_add_tail(&tx[1], &msg); + ret = spi_sync(spi, &msg); + if (ret) + goto fail; + + return 0; +fail: + dev_err(&mgr->dev, "Cleanup failed\n"); + return ret; +} + +static enum fpga_mgr_states machxo2_spi_state(struct fpga_manager *mgr) +{ + return FPGA_MGR_STATE_UNKNOWN; +} + +static int machxo2_write_init(struct fpga_manager *mgr, + struct fpga_image_info *info, + const char *buf, size_t count) +{ + struct spi_device *spi = mgr->priv; + struct spi_message msg; + struct spi_transfer tx[3]; + u8 enable[] = ISC_ENABLE; + u8 erase[] = ISC_ERASE; + u8 initaddr[] = LSC_INITADDRESS; + unsigned long status; + int ret; + + if ((info->flags & FPGA_MGR_PARTIAL_RECONFIG)) { + dev_err(&mgr->dev, + "Partial reconfiguration is not supported\n"); + return -ENOTSUPP; + } + + get_status(spi, &status); + dump_status_reg(&status); + memset(tx, 0, sizeof(tx)); + spi_message_init(&msg); + tx[0].tx_buf = &enable; + tx[0].len = sizeof(enable); + tx[0].delay_usecs = MACHXO2_LOW_DELAY; + spi_message_add_tail(&tx[0], &msg); + + tx[1].tx_buf = &erase; + tx[1].len = sizeof(erase); + spi_message_add_tail(&tx[1], &msg); + ret = spi_sync(spi, &msg); + if (ret) + goto fail; + + ret = wait_until_not_busy(spi); + if (ret) + goto fail; + + get_status(spi, &status); + if (test_bit(FAIL, &status)) + goto fail; + dump_status_reg(&status); + + spi_message_init(&msg); + tx[2].tx_buf = &initaddr; + tx[2].len = sizeof(initaddr); + spi_message_add_tail(&tx[2], &msg); + ret = spi_sync(spi, &msg); + if (ret) + goto fail; + + get_status(spi, &status); + dump_status_reg(&status); + return 0; +fail: + dev_err(&mgr->dev, "Error during FPGA init.\n"); + return ret; +} + +static int machxo2_write(struct fpga_manager *mgr, const char *buf, + size_t count) +{ + struct spi_device *spi = mgr->priv; + struct spi_message msg; + struct spi_transfer tx; + u8 progincr[] = LSC_PROGINCRNV; + u8 payload[MACHXO2_BUF_SIZE]; + unsigned long status; + int i, ret; + + if (count % MACHXO2_PAGE_SIZE != 0) { + dev_err(&mgr->dev, "Malformed payload.\n"); + return -EINVAL; + } + get_status(spi, &status); + dump_status_reg(&status); + memcpy(payload, &progincr, sizeof(progincr)); + for (i = 0; i < count; i += MACHXO2_PAGE_SIZE) { + memcpy(&payload[sizeof(progincr)], &buf[i], MACHXO2_PAGE_SIZE); + memset(&tx, 0, sizeof(tx)); + spi_message_init(&msg); + tx.tx_buf = payload; + tx.len = MACHXO2_BUF_SIZE; + tx.delay_usecs = MACHXO2_HIGH_DELAY; + spi_message_add_tail(&tx, &msg); + ret = spi_sync(spi, &msg); + if (ret) { + dev_err(&mgr->dev, "Error loading the bitstream.\n"); + return ret; + } + } + get_status(spi, &status); + dump_status_reg(&status); + + return 0; +} + +static int machxo2_write_complete(struct fpga_manager *mgr, + struct fpga_image_info *info) +{ + struct spi_device *spi = mgr->priv; + struct spi_message msg; + struct spi_transfer tx[2]; + u8 progdone[] = ISC_PROGRAMDONE; + u8 refresh[] = LSC_REFRESH; + unsigned long status; + int ret, refreshloop = 0; + + memset(tx, 0, sizeof(tx)); + spi_message_init(&msg); + tx[0].tx_buf = &progdone; + tx[0].len = sizeof(progdone); + spi_message_add_tail(&tx[0], &msg); + ret = spi_sync(spi, &msg); + if (ret) + goto fail; + ret = wait_until_not_busy(spi); + if (ret) + goto fail; + + get_status(spi, &status); + dump_status_reg(&status); + if (!test_bit(DONE, &status)) { + machxo2_cleanup(mgr); + goto fail; + } + + do { + spi_message_init(&msg); + tx[1].tx_buf = &refresh; + tx[1].len = sizeof(refresh); + tx[1].delay_usecs = MACHXO2_REFRESH; + spi_message_add_tail(&tx[1], &msg); + ret = spi_sync(spi, &msg); + if (ret) + goto fail; + + /* check refresh status */ + get_status(spi, &status); + dump_status_reg(&status); + if (!test_bit(BUSY, &status) && test_bit(DONE, &status) && + get_err(&status) == ENOERR) + break; + if (++refreshloop == MACHXO2_MAX_REFRESH_LOOP) { + machxo2_cleanup(mgr); + goto fail; + } + } while (1); + + get_status(spi, &status); + dump_status_reg(&status); + return 0; +fail: + dev_err(&mgr->dev, "Refresh failed.\n"); + return ret; +} + +static const struct fpga_manager_ops machxo2_ops = { + .state = machxo2_spi_state, + .write_init = machxo2_write_init, + .write = machxo2_write, + .write_complete = machxo2_write_complete, +}; + +static int machxo2_spi_probe(struct spi_device *spi) +{ + struct device *dev = &spi->dev; + + if (spi->max_speed_hz > MACHXO2_MAX_SPEED) { + dev_err(dev, "Speed is too high\n"); + return -EINVAL; + } + + return fpga_mgr_register(dev, "Lattice MachXO2 SPI FPGA Manager", + &machxo2_ops, spi); +} + +static int machxo2_spi_remove(struct spi_device *spi) +{ + struct device *dev = &spi->dev; + + fpga_mgr_unregister(dev); + + return 0; +} + +static const struct of_device_id of_match[] = { + { .compatible = "lattice,machxo2-slave-spi", }, + {} +}; +MODULE_DEVICE_TABLE(of, of_match); + +static const struct spi_device_id lattice_ids[] = { + { "machxo2-slave-spi", 0 }, + { }, +}; +MODULE_DEVICE_TABLE(spi, lattice_ids); + +static struct spi_driver machxo2_spi_driver = { + .driver = { + .name = "machxo2-slave-spi", + .of_match_table = of_match_ptr(of_match), + }, + .probe = machxo2_spi_probe, + .remove = machxo2_spi_remove, + .id_table = lattice_ids, +}; + +module_spi_driver(machxo2_spi_driver) + +MODULE_AUTHOR("Paolo Pisati <p.pisati@gmail.com>"); +MODULE_DESCRIPTION("Load Lattice FPGA firmware over SPI"); +MODULE_LICENSE("GPL v2"); -- 2.7.4 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [PATCH 2/2] fpga: lattice machxo2: Add Lattice MachXO2 support 2018-03-16 15:54 ` [PATCH 2/2] fpga: lattice machxo2: Add Lattice MachXO2 support Paolo Pisati @ 2018-03-16 16:26 ` Moritz Fischer 2018-03-19 18:09 ` Paolo Pisati 0 siblings, 1 reply; 12+ messages in thread From: Moritz Fischer @ 2018-03-16 16:26 UTC (permalink / raw) To: Paolo Pisati Cc: Alan Tull, Moritz Fischer, Rob Herring, Mark Rutland, linux-fpga, devicetree, linux-kernel On Fri, Mar 16, 2018 at 04:54:29PM +0100, Paolo Pisati wrote: > This patch adds support to the FPGA manager for programming > MachXO2 device’s internal flash memory, via slave SPI. > > Signed-off-by: Paolo Pisati <p.pisati@gmail.com> > --- > drivers/fpga/Kconfig | 8 + > drivers/fpga/Makefile | 1 + > drivers/fpga/machxo2-spi.c | 410 +++++++++++++++++++++++++++++++++++++++++++++ > 3 files changed, 419 insertions(+) > create mode 100644 drivers/fpga/machxo2-spi.c > > diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig > index ad5448f..65ccbc5 100644 > --- a/drivers/fpga/Kconfig > +++ b/drivers/fpga/Kconfig > @@ -38,6 +38,14 @@ config FPGA_MGR_ALTERA_PS_SPI > FPGA manager driver support for Altera Arria/Cyclone/Stratix > using the passive serial interface over SPI. > > +config FPGA_MGR_MACHXO2_SPI > + tristate "Lattice MachXO2 SPI" > + depends on SPI > + help > + FPGA manager driver support for Lattice MachXO2 configuration > + over slave SPI interface. > + > + > config FPGA_MGR_SOCFPGA > tristate "Altera SOCFPGA FPGA Manager" > depends on ARCH_SOCFPGA || COMPILE_TEST > diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile > index f98dcf1..38abb08 100644 > --- a/drivers/fpga/Makefile > +++ b/drivers/fpga/Makefile > @@ -10,6 +10,7 @@ obj-$(CONFIG_FPGA) += fpga-mgr.o > obj-$(CONFIG_FPGA_MGR_ALTERA_CVP) += altera-cvp.o > obj-$(CONFIG_FPGA_MGR_ALTERA_PS_SPI) += altera-ps-spi.o > obj-$(CONFIG_FPGA_MGR_ICE40_SPI) += ice40-spi.o > +obj-$(CONFIG_FPGA_MGR_MACHXO2_SPI) += machxo2-spi.o > obj-$(CONFIG_FPGA_MGR_SOCFPGA) += socfpga.o > obj-$(CONFIG_FPGA_MGR_SOCFPGA_A10) += socfpga-a10.o > obj-$(CONFIG_FPGA_MGR_TS73XX) += ts73xx-fpga.o > diff --git a/drivers/fpga/machxo2-spi.c b/drivers/fpga/machxo2-spi.c > new file mode 100644 > index 0000000..3c7fc3e > --- /dev/null > +++ b/drivers/fpga/machxo2-spi.c > @@ -0,0 +1,410 @@ > +/** > + * Lattice MachXO2 Slave SPI Driver > + * > + * Copyright (C) 2018 Paolo Pisati <p.pisati@gmail.com> > + * > + * This program is free software; you can redistribute it and/or modify it > + * under the terms and conditions of the GNU General Public License, > + * version 2, as published by the Free Software Foundation. SPDX please. > + * > + * Manage Lattice FPGA firmware that is loaded over SPI using > + * the slave serial configuration interface. > + */ > + > +#include <linux/delay.h> > +#include <linux/fpga/fpga-mgr.h> > +#include <linux/gpio/consumer.h> > +#include <linux/module.h> > +#include <linux/of.h> > +#include <linux/spi/spi.h> > + > +//#define MACHXO2_DEBUG ?! No ;-) > + > +/* MachXO2 Programming Guide - sysCONFIG Programming Commands */ > +#define IDCODE_PUB {0xe0, 0x00, 0x00, 0x00} > +#define ISC_ENABLE {0xc6, 0x08, 0x00, 0x00} > +#define ISC_ERASE {0x0e, 0x04, 0x00, 0x00} > +#define ISC_PROGRAMDONE {0x5e, 0x00, 0x00, 0x00} > +#define LSC_INITADDRESS {0x46, 0x00, 0x00, 0x00} > +#define LSC_PROGINCRNV {0x70, 0x00, 0x00, 0x01} > +#define LSC_READ_STATUS {0x3c, 0x00, 0x00, 0x00} > +#define LSC_REFRESH {0x79, 0x00, 0x00, 0x00} > + > +/* > + * Max CCLK in Slave SPI mode according to 'MachXO2 Family Data > + * Sheet' sysCONFIG Port Timing Specifications (3-36) > + */ > +#define MACHXO2_MAX_SPEED 66000000 > + > +#define MACHXO2_LOW_DELAY 5 /* us */ > +#define MACHXO2_HIGH_DELAY 200 /* us */ > +#define MACHXO2_REFRESH 4800 /* us */ > +#define MACHXO2_MAX_BUSY_LOOP 128 > +#define MACHXO2_MAX_REFRESH_LOOP 16 > + > +#define MACHXO2_PAGE_SIZE 16 > +#define MACHXO2_BUF_SIZE (MACHXO2_PAGE_SIZE + 4) > + > +/* Status register bits, errors and error mask */ > +#define BUSY 12 > +#define DONE 8 > +#define DVER 27 > +#define ENAB 9 > +#define ERRBITS 23 > +#define ERRMASK 7 > +#define FAIL 13 > + > +#define ENOERR 0 /* no error */ > +#define EID 1 > +#define ECMD 2 > +#define ECRC 3 > +#define EPREAM 4 /* preamble error */ > +#define EABRT 5 /* abort error */ > +#define EOVERFL 6 /* overflow error */ > +#define ESDMEOF 7 /* SDM EOF */ > + > +static inline u8 get_err(unsigned long *status) > +{ > + return (*status >> ERRBITS) & ERRMASK; > +} > + > +static int get_status(struct spi_device *spi, unsigned long *status) > +{ > + struct spi_message msg; > + struct spi_transfer rx, tx; > + u8 cmd[] = LSC_READ_STATUS; > + int ret; > + > + memset(&rx, 0, sizeof(rx)); > + memset(&tx, 0, sizeof(tx)); > + tx.tx_buf = cmd; > + tx.len = sizeof(cmd); > + rx.rx_buf = status; > + rx.len = 4; > + spi_message_init(&msg); > + spi_message_add_tail(&tx, &msg); > + spi_message_add_tail(&rx, &msg); > + ret = spi_sync(spi, &msg); > + if (ret) > + return ret; > + > + *status = be32_to_cpu(*status); > + return 0; > +} > + > +#ifdef MACHXO2_DEBUG Not a fan of this ... > +static void dump_status_reg(unsigned long *status) > +{ > + char *ferr; > + > + switch (get_err(status)) { > + case ENOERR: > + ferr = "No Error"; > + break; > + case EID: > + ferr = "ID ERR"; > + break; > + case ECMD: > + ferr = "CMD ERR"; > + break; > + case ECRC: > + ferr = "CRC ERR"; > + break; > + case EPREAM: > + ferr = "Preamble ERR"; > + break; > + case EABRT: > + ferr = "Abort ERR"; > + break; > + case EOVERFL: > + ferr = "Overflow ERR"; > + break; > + case ESDMEOF: > + ferr = "SDM EOF"; > + break; > + default: > + ferr = "Default switch case"; > + } > + printk(KERN_DEBUG "machxo2 status: 0x%08lX - done=%d, cfgena=%d, busy=%d, fail=%d, devver=%d, err=%s\n", > + *status, test_bit(DONE, status), test_bit(ENAB, status), > + test_bit(BUSY, status), test_bit(FAIL, status), > + test_bit(DVER, status), ferr); Not sure we need this function in the first place, if you really think you need it at least use pr_dbg() or pr_err() here. > +} > +#else > +static void dump_status_reg(unsigned long *status) {} > +#endif > + > +static int wait_until_not_busy(struct spi_device *spi) > +{ > + unsigned long status; > + int ret, loop = 0; > + > + do { > + ret = get_status(spi, &status); > + if (ret) > + break; > + if (++loop >= MACHXO2_MAX_BUSY_LOOP) { > + ret = -EBUSY; > + break; > + } > + } while (test_bit(BUSY, &status)); > + > + return ret; > +} > + > +static int machxo2_cleanup(struct fpga_manager *mgr) > +{ > + struct spi_device *spi = mgr->priv; > + struct spi_message msg; > + struct spi_transfer tx[2]; > + u8 erase[] = ISC_ERASE; > + u8 refresh[] = LSC_REFRESH; > + int ret; > + > + memset(tx, 0, sizeof(tx)); > + spi_message_init(&msg); > + tx[0].tx_buf = &erase; > + tx[0].len = sizeof(erase); > + spi_message_add_tail(&tx[0], &msg); > + ret = spi_sync(spi, &msg); > + if (ret) > + goto fail; > + > + ret = wait_until_not_busy(spi); > + if (ret) > + goto fail; > + > + spi_message_init(&msg); > + tx[1].tx_buf = &refresh; > + tx[1].len = sizeof(refresh); > + tx[1].delay_usecs = MACHXO2_REFRESH; > + spi_message_add_tail(&tx[1], &msg); > + ret = spi_sync(spi, &msg); > + if (ret) > + goto fail; > + > + return 0; > +fail: > + dev_err(&mgr->dev, "Cleanup failed\n"); > + return ret; > +} > + > +static enum fpga_mgr_states machxo2_spi_state(struct fpga_manager *mgr) > +{ > + return FPGA_MGR_STATE_UNKNOWN; > +} To understand this correctly: Further up you have a way to determine the state you're in, but then you only use that for debug printout, while here where you should provide the status you say FPGA_MGR_STATE_UNKNOWN? Am I missing something here? > + > +static int machxo2_write_init(struct fpga_manager *mgr, > + struct fpga_image_info *info, > + const char *buf, size_t count) > +{ > + struct spi_device *spi = mgr->priv; > + struct spi_message msg; > + struct spi_transfer tx[3]; > + u8 enable[] = ISC_ENABLE; > + u8 erase[] = ISC_ERASE; > + u8 initaddr[] = LSC_INITADDRESS; > + unsigned long status; > + int ret; > + > + if ((info->flags & FPGA_MGR_PARTIAL_RECONFIG)) { > + dev_err(&mgr->dev, > + "Partial reconfiguration is not supported\n"); > + return -ENOTSUPP; > + } > + > + get_status(spi, &status); > + dump_status_reg(&status); > + memset(tx, 0, sizeof(tx)); > + spi_message_init(&msg); > + tx[0].tx_buf = &enable; > + tx[0].len = sizeof(enable); > + tx[0].delay_usecs = MACHXO2_LOW_DELAY; > + spi_message_add_tail(&tx[0], &msg); > + > + tx[1].tx_buf = &erase; > + tx[1].len = sizeof(erase); > + spi_message_add_tail(&tx[1], &msg); > + ret = spi_sync(spi, &msg); > + if (ret) > + goto fail; > + > + ret = wait_until_not_busy(spi); > + if (ret) > + goto fail; > + > + get_status(spi, &status); > + if (test_bit(FAIL, &status)) > + goto fail; > + dump_status_reg(&status); > + > + spi_message_init(&msg); > + tx[2].tx_buf = &initaddr; > + tx[2].len = sizeof(initaddr); > + spi_message_add_tail(&tx[2], &msg); > + ret = spi_sync(spi, &msg); > + if (ret) > + goto fail; > + > + get_status(spi, &status); > + dump_status_reg(&status); > + return 0; > +fail: > + dev_err(&mgr->dev, "Error during FPGA init.\n"); > + return ret; > +} > + > +static int machxo2_write(struct fpga_manager *mgr, const char *buf, > + size_t count) > +{ > + struct spi_device *spi = mgr->priv; > + struct spi_message msg; > + struct spi_transfer tx; > + u8 progincr[] = LSC_PROGINCRNV; > + u8 payload[MACHXO2_BUF_SIZE]; > + unsigned long status; > + int i, ret; > + > + if (count % MACHXO2_PAGE_SIZE != 0) { > + dev_err(&mgr->dev, "Malformed payload.\n"); > + return -EINVAL; > + } > + get_status(spi, &status); > + dump_status_reg(&status); > + memcpy(payload, &progincr, sizeof(progincr)); > + for (i = 0; i < count; i += MACHXO2_PAGE_SIZE) { > + memcpy(&payload[sizeof(progincr)], &buf[i], MACHXO2_PAGE_SIZE); > + memset(&tx, 0, sizeof(tx)); > + spi_message_init(&msg); > + tx.tx_buf = payload; > + tx.len = MACHXO2_BUF_SIZE; > + tx.delay_usecs = MACHXO2_HIGH_DELAY; > + spi_message_add_tail(&tx, &msg); > + ret = spi_sync(spi, &msg); > + if (ret) { > + dev_err(&mgr->dev, "Error loading the bitstream.\n"); > + return ret; > + } > + } > + get_status(spi, &status); > + dump_status_reg(&status); > + > + return 0; > +} > + > +static int machxo2_write_complete(struct fpga_manager *mgr, > + struct fpga_image_info *info) > +{ > + struct spi_device *spi = mgr->priv; > + struct spi_message msg; > + struct spi_transfer tx[2]; > + u8 progdone[] = ISC_PROGRAMDONE; > + u8 refresh[] = LSC_REFRESH; > + unsigned long status; > + int ret, refreshloop = 0; > + > + memset(tx, 0, sizeof(tx)); > + spi_message_init(&msg); > + tx[0].tx_buf = &progdone; > + tx[0].len = sizeof(progdone); > + spi_message_add_tail(&tx[0], &msg); > + ret = spi_sync(spi, &msg); > + if (ret) > + goto fail; > + ret = wait_until_not_busy(spi); > + if (ret) > + goto fail; > + > + get_status(spi, &status); > + dump_status_reg(&status); > + if (!test_bit(DONE, &status)) { > + machxo2_cleanup(mgr); > + goto fail; > + } > + > + do { > + spi_message_init(&msg); > + tx[1].tx_buf = &refresh; > + tx[1].len = sizeof(refresh); > + tx[1].delay_usecs = MACHXO2_REFRESH; > + spi_message_add_tail(&tx[1], &msg); > + ret = spi_sync(spi, &msg); > + if (ret) > + goto fail; > + > + /* check refresh status */ > + get_status(spi, &status); > + dump_status_reg(&status); > + if (!test_bit(BUSY, &status) && test_bit(DONE, &status) && > + get_err(&status) == ENOERR) > + break; > + if (++refreshloop == MACHXO2_MAX_REFRESH_LOOP) { > + machxo2_cleanup(mgr); > + goto fail; > + } > + } while (1); > + > + get_status(spi, &status); > + dump_status_reg(&status); > + return 0; > +fail: > + dev_err(&mgr->dev, "Refresh failed.\n"); > + return ret; > +} > + > +static const struct fpga_manager_ops machxo2_ops = { > + .state = machxo2_spi_state, > + .write_init = machxo2_write_init, > + .write = machxo2_write, > + .write_complete = machxo2_write_complete, > +}; > + > +static int machxo2_spi_probe(struct spi_device *spi) > +{ > + struct device *dev = &spi->dev; > + > + if (spi->max_speed_hz > MACHXO2_MAX_SPEED) { > + dev_err(dev, "Speed is too high\n"); > + return -EINVAL; > + } > + > + return fpga_mgr_register(dev, "Lattice MachXO2 SPI FPGA Manager", > + &machxo2_ops, spi); > +} > + > +static int machxo2_spi_remove(struct spi_device *spi) > +{ > + struct device *dev = &spi->dev; > + > + fpga_mgr_unregister(dev); > + > + return 0; > +} > + > +static const struct of_device_id of_match[] = { > + { .compatible = "lattice,machxo2-slave-spi", }, > + {} > +}; > +MODULE_DEVICE_TABLE(of, of_match); > + > +static const struct spi_device_id lattice_ids[] = { > + { "machxo2-slave-spi", 0 }, > + { }, > +}; > +MODULE_DEVICE_TABLE(spi, lattice_ids); > + > +static struct spi_driver machxo2_spi_driver = { > + .driver = { > + .name = "machxo2-slave-spi", > + .of_match_table = of_match_ptr(of_match), > + }, > + .probe = machxo2_spi_probe, > + .remove = machxo2_spi_remove, > + .id_table = lattice_ids, > +}; > + > +module_spi_driver(machxo2_spi_driver) > + > +MODULE_AUTHOR("Paolo Pisati <p.pisati@gmail.com>"); > +MODULE_DESCRIPTION("Load Lattice FPGA firmware over SPI"); > +MODULE_LICENSE("GPL v2"); > -- > 2.7.4 > ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 2/2] fpga: lattice machxo2: Add Lattice MachXO2 support 2018-03-16 16:26 ` Moritz Fischer @ 2018-03-19 18:09 ` Paolo Pisati 0 siblings, 0 replies; 12+ messages in thread From: Paolo Pisati @ 2018-03-19 18:09 UTC (permalink / raw) To: Moritz Fischer Cc: Paolo Pisati, Alan Tull, Rob Herring, Mark Rutland, linux-fpga, devicetree, linux-kernel On Fri, Mar 16, 2018 at 09:26:54AM -0700, Moritz Fischer wrote: > > > > +static enum fpga_mgr_states machxo2_spi_state(struct fpga_manager *mgr) > > +{ > > + return FPGA_MGR_STATE_UNKNOWN; > > +} > > To understand this correctly: Further up you have a way to determine the > state you're in, but then you only use that for debug printout, while > here where you should provide the status you say FPGA_MGR_STATE_UNKNOWN? > > Am I missing something here? This is more of a generic function ('What's the state of the FPGA now?') while dump_status_reg() is invoked after a specific SPI command is sent to the FPGA to keep track of the status of the chip and check that it adhere to the state machine. I'll send a v7. -- bye, p. ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 0/2 v8] Lattice MachXO2 Slave SPI FPGA Manager support @ 2018-03-23 12:27 Paolo Pisati 2018-03-23 12:27 ` [PATCH 1/2] dt: bindings: fpga: add lattice machxo2 slave spi binding description Paolo Pisati 0 siblings, 1 reply; 12+ messages in thread From: Paolo Pisati @ 2018-03-23 12:27 UTC (permalink / raw) To: Alan Tull, Moritz Fischer, Rob Herring, Mark Rutland Cc: linux-fpga, devicetree, linux-kernel Hi all, this series adds support for the Lattice MachXO2 FPGA chip, programmed over Slave SPI. Tested on a raspberry pi3, beaglebone black (little endian mode) and imx6 hummingboard (big endian mode) + bugblat's pif2 fpga hat (machxo2 7000HC) or tinyfpga A1/A2 (machxo2 256HC / 1200HC), in SPI slave mode with varying bus speed. Changes since v7: * misc style fixes, among which: * static const u8 cmd[] * #ifdef DEBUG ... #endif reorder * introduction of get_err_string() * direct returns to reduce line count * indentation Paolo Pisati (2): dt: bindings: fpga: add lattice machxo2 slave spi binding description fpga: lattice machxo2: Add Lattice MachXO2 support .../bindings/fpga/lattice-machxo2-spi.txt | 29 ++ drivers/fpga/Kconfig | 8 + drivers/fpga/Makefile | 1 + drivers/fpga/machxo2-spi.c | 388 +++++++++++++++++++++ 4 files changed, 426 insertions(+) create mode 100644 Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt create mode 100644 drivers/fpga/machxo2-spi.c -- 2.7.4 ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 1/2] dt: bindings: fpga: add lattice machxo2 slave spi binding description 2018-03-23 12:27 [PATCH 0/2 v8] Lattice MachXO2 Slave SPI FPGA Manager support Paolo Pisati @ 2018-03-23 12:27 ` Paolo Pisati 0 siblings, 0 replies; 12+ messages in thread From: Paolo Pisati @ 2018-03-23 12:27 UTC (permalink / raw) To: Alan Tull, Moritz Fischer, Rob Herring, Mark Rutland Cc: linux-fpga, devicetree, linux-kernel Add dt binding documentation details for Lattice MachXO2 FPGA configuration over Slave SPI interface. Signed-off-by: Paolo Pisati <p.pisati@gmail.com> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Moritz Fischer <mdf@kernel.org> Acked-by: Alan Tull <atull@kernel.org> --- .../bindings/fpga/lattice-machxo2-spi.txt | 29 ++++++++++++++++++++++ 1 file changed, 29 insertions(+) create mode 100644 Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt diff --git a/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt b/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt new file mode 100644 index 0000000..a8c362e --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt @@ -0,0 +1,29 @@ +Lattice MachXO2 Slave SPI FPGA Manager + +Lattice MachXO2 FPGAs support a method of loading the bitstream over +a 'slave SPI' interface. + +See 'MachXO2ProgrammingandConfigurationUsageGuide.pdf' on www.latticesemi.com + +Required properties: +- compatible: should contain "lattice,machxo2-slave-spi" +- reg: spi chip select of the FPGA + +Example for full FPGA configuration: + + fpga-region0 { + compatible = "fpga-region"; + fpga-mgr = <&fpga_mgr_spi>; + #address-cells = <0x1>; + #size-cells = <0x1>; + }; + + spi1: spi@2000 { + ... + + fpga_mgr_spi: fpga-mgr@0 { + compatible = "lattice,machxo2-slave-spi"; + spi-max-frequency = <8000000>; + reg = <0>; + }; + }; -- 2.7.4 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH 0/2 v7] Lattice MachXO2 Slave SPI FPGA Manager support @ 2018-03-21 17:35 Paolo Pisati 2018-03-21 17:35 ` [PATCH 1/2] dt: bindings: fpga: add lattice machxo2 slave spi binding description Paolo Pisati 0 siblings, 1 reply; 12+ messages in thread From: Paolo Pisati @ 2018-03-21 17:35 UTC (permalink / raw) To: Alan Tull, Moritz Fischer, Rob Herring, Mark Rutland Cc: linux-fpga, devicetree, linux-kernel Hi all, this series adds support for the Lattice MachXO2 FPGA chip, programmed over Slave SPI. Tested on a raspberry pi3, beaglebone black (little endian mode) and imx6 hummingboard (big endian mode) + bugblat's pif2 fpga hat (machxo2 7000HC) or tinyfpga A1/A2 (machxo2 256HC / 1200HC), in SPI slave mode with varying bus speed. Changes since v6: * added the SPDX boilerplate * switched to pr_debug() and renamed MACHXO2_DEBUG to DEBUG Paolo Pisati (2): dt: bindings: fpga: add lattice machxo2 slave spi binding description fpga: lattice machxo2: Add Lattice MachXO2 support .../bindings/fpga/lattice-machxo2-spi.txt | 29 ++ drivers/fpga/Kconfig | 8 + drivers/fpga/Makefile | 1 + drivers/fpga/machxo2-spi.c | 405 +++++++++++++++++++++ 4 files changed, 443 insertions(+) create mode 100644 Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt create mode 100644 drivers/fpga/machxo2-spi.c -- 2.7.4 ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 1/2] dt: bindings: fpga: add lattice machxo2 slave spi binding description 2018-03-21 17:35 [PATCH 0/2 v7] Lattice MachXO2 Slave SPI FPGA Manager support Paolo Pisati @ 2018-03-21 17:35 ` Paolo Pisati 0 siblings, 0 replies; 12+ messages in thread From: Paolo Pisati @ 2018-03-21 17:35 UTC (permalink / raw) To: Alan Tull, Moritz Fischer, Rob Herring, Mark Rutland Cc: linux-fpga, devicetree, linux-kernel Add dt binding documentation details for Lattice MachXO2 FPGA configuration over Slave SPI interface. Signed-off-by: Paolo Pisati <p.pisati@gmail.com> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Moritz Fischer <mdf@kernel.org> Acked-by: Alan Tull <atull@kernel.org> --- .../bindings/fpga/lattice-machxo2-spi.txt | 29 ++++++++++++++++++++++ 1 file changed, 29 insertions(+) create mode 100644 Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt diff --git a/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt b/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt new file mode 100644 index 0000000..a8c362e --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt @@ -0,0 +1,29 @@ +Lattice MachXO2 Slave SPI FPGA Manager + +Lattice MachXO2 FPGAs support a method of loading the bitstream over +a 'slave SPI' interface. + +See 'MachXO2ProgrammingandConfigurationUsageGuide.pdf' on www.latticesemi.com + +Required properties: +- compatible: should contain "lattice,machxo2-slave-spi" +- reg: spi chip select of the FPGA + +Example for full FPGA configuration: + + fpga-region0 { + compatible = "fpga-region"; + fpga-mgr = <&fpga_mgr_spi>; + #address-cells = <0x1>; + #size-cells = <0x1>; + }; + + spi1: spi@2000 { + ... + + fpga_mgr_spi: fpga-mgr@0 { + compatible = "lattice,machxo2-slave-spi"; + spi-max-frequency = <8000000>; + reg = <0>; + }; + }; -- 2.7.4 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v5 0/2] Lattice MachXO2 Slave SPI FPGA Manager support
@ 2017-07-06 10:01 Paolo Pisati
2017-07-06 10:01 ` [PATCH 1/2] dt: bindings: fpga: add lattice machxo2 slave spi binding description Paolo Pisati
0 siblings, 1 reply; 12+ messages in thread
From: Paolo Pisati @ 2017-07-06 10:01 UTC (permalink / raw)
To: Alan Tull, Moritz Fischer
Cc: Rob Herring, Mark Rutland, linux-fpga, devicetree, linux-kernel
Hi all,
this series adds support for the Lattice MachXO2 FPGA chip, programmed
over Slave SPI.
Tested on my raspberry pi3 + bugblat's pif2 fpga hat.
Changes from v1:
* fixed all the warnings pointed out by 'checkpatch --strict' and
Alan Tull
Changes from v2:
* convert to BIT() macro and spi_message_init() / trans.delay_usecs
Changes from v3;
* loop unroll machxo2_write() and collate writes in a single spi_sync()
Changes from v4:
* rebased on 3.12
Paolo Pisati (2):
dt: bindings: fpga: add lattice machxo2 slave spi binding description
fpga: lattice machxo2: Add Lattice MachXO2 support
.../bindings/fpga/lattice-machxo2-spi.txt | 29 ++
drivers/fpga/Kconfig | 7 +
drivers/fpga/Makefile | 1 +
drivers/fpga/machxo2-spi.c | 298 +++++++++++++++++++++
4 files changed, 335 insertions(+)
create mode 100644 Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt
create mode 100644 drivers/fpga/machxo2-spi.c
--
2.7.4
^ permalink raw reply [flat|nested] 12+ messages in thread* [PATCH 1/2] dt: bindings: fpga: add lattice machxo2 slave spi binding description 2017-07-06 10:01 [PATCH v5 0/2] Lattice MachXO2 Slave SPI FPGA Manager support Paolo Pisati @ 2017-07-06 10:01 ` Paolo Pisati 0 siblings, 0 replies; 12+ messages in thread From: Paolo Pisati @ 2017-07-06 10:01 UTC (permalink / raw) To: Alan Tull, Moritz Fischer Cc: Rob Herring, Mark Rutland, linux-fpga, devicetree, linux-kernel Add dt binding documentation details for Lattice MachXO2 FPGA configuration over Slave SPI interface. Signed-off-by: Paolo Pisati <p.pisati@gmail.com> Acked-by: Rob Herring <robh@kernel.org> --- .../bindings/fpga/lattice-machxo2-spi.txt | 29 ++++++++++++++++++++++ 1 file changed, 29 insertions(+) create mode 100644 Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt diff --git a/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt b/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt new file mode 100644 index 0000000..c3ef26bd --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt @@ -0,0 +1,29 @@ +Lattice MachXO2 Slave SPI FPGA Manager + +Lattice MachXO2 FPGAs support a method of loading the bitstream over +'slave SPI' interface. + +See 'MachXO2ProgrammingandConfigurationUsageGuide.pdf' on www.latticesemi.com + +Required properties: +- compatible: should contain "lattice,machxo2-slave-spi" +- reg: spi chip select of the FPGA + +Example for full FPGA configuration: + + fpga-region0 { + compatible = "fpga-region"; + fpga-mgr = <&fpga_mgr_spi>; + #address-cells = <0x1>; + #size-cells = <0x1>; + }; + + spi1: spi@2000 { + ... + + fpga_mgr_spi: fpga-mgr@0 { + compatible = "lattice,machxo2-slave-spi"; + spi-max-frequency = <60000000>; + reg = <0>; + }; + }; -- 2.7.4 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH 0/2] Lattice MachXO2 Passive SPI FPGA Manager support @ 2017-04-23 15:20 Paolo Pisati 2017-04-23 15:20 ` [PATCH 1/2] dt: bindings: fpga: add lattice machxo2 slave spi binding description Paolo Pisati 0 siblings, 1 reply; 12+ messages in thread From: Paolo Pisati @ 2017-04-23 15:20 UTC (permalink / raw) To: Rob Herring, Mark Rutland, Alan Tull, Moritz Fischer Cc: devicetree, linux-fpga, linux-kernel Hi all, this series adds support for the Lattice MachXO2 FPGA chip, programmed over Slave SPI. Tested on my raspberry pi3 + bugblat's pif2 fpga hat. Paolo Pisati (2): dt: bindings: fpga: add lattice machxo2 slave spi binding description fpga: lattice machxo2: Add Lattice MachXO2 support .../bindings/fpga/lattice-machxo2-spi.txt | 29 +++ drivers/fpga/Kconfig | 7 + drivers/fpga/Makefile | 1 + drivers/fpga/machxo2-spi.c | 199 +++++++++++++++++++++ 4 files changed, 236 insertions(+) create mode 100644 Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt create mode 100644 drivers/fpga/machxo2-spi.c -- 2.7.4 ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 1/2] dt: bindings: fpga: add lattice machxo2 slave spi binding description 2017-04-23 15:20 [PATCH 0/2] Lattice MachXO2 Passive SPI FPGA Manager support Paolo Pisati @ 2017-04-23 15:20 ` Paolo Pisati 2017-04-28 17:54 ` Rob Herring 0 siblings, 1 reply; 12+ messages in thread From: Paolo Pisati @ 2017-04-23 15:20 UTC (permalink / raw) To: Rob Herring, Mark Rutland, Alan Tull, Moritz Fischer Cc: devicetree, linux-fpga, linux-kernel Add dt binding documentation details for Lattice MachXO2 FPGA configuration over Slave SPI interface. Signed-off-by: Paolo Pisati <p.pisati@gmail.com> --- .../bindings/fpga/lattice-machxo2-spi.txt | 29 ++++++++++++++++++++++ 1 file changed, 29 insertions(+) create mode 100644 Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt diff --git a/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt b/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt new file mode 100644 index 0000000..c3ef26bd --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt @@ -0,0 +1,29 @@ +Lattice MachXO2 Slave SPI FPGA Manager + +Lattice MachXO2 FPGAs support a method of loading the bitstream over +'slave SPI' interface. + +See 'MachXO2ProgrammingandConfigurationUsageGuide.pdf' on www.latticesemi.com + +Required properties: +- compatible: should contain "lattice,machxo2-slave-spi" +- reg: spi chip select of the FPGA + +Example for full FPGA configuration: + + fpga-region0 { + compatible = "fpga-region"; + fpga-mgr = <&fpga_mgr_spi>; + #address-cells = <0x1>; + #size-cells = <0x1>; + }; + + spi1: spi@2000 { + ... + + fpga_mgr_spi: fpga-mgr@0 { + compatible = "lattice,machxo2-slave-spi"; + spi-max-frequency = <60000000>; + reg = <0>; + }; + }; -- 2.7.4 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [PATCH 1/2] dt: bindings: fpga: add lattice machxo2 slave spi binding description 2017-04-23 15:20 ` [PATCH 1/2] dt: bindings: fpga: add lattice machxo2 slave spi binding description Paolo Pisati @ 2017-04-28 17:54 ` Rob Herring 0 siblings, 0 replies; 12+ messages in thread From: Rob Herring @ 2017-04-28 17:54 UTC (permalink / raw) To: Paolo Pisati Cc: Mark Rutland, Alan Tull, Moritz Fischer, devicetree, linux-fpga, linux-kernel On Sun, Apr 23, 2017 at 05:20:44PM +0200, Paolo Pisati wrote: > Add dt binding documentation details for Lattice MachXO2 FPGA configuration > over Slave SPI interface. > > Signed-off-by: Paolo Pisati <p.pisati@gmail.com> > --- > .../bindings/fpga/lattice-machxo2-spi.txt | 29 ++++++++++++++++++++++ > 1 file changed, 29 insertions(+) > create mode 100644 Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt Acked-by: Rob Herring <robh@kernel.org> ^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2018-03-23 12:27 UTC | newest] Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2018-03-16 15:54 [PATCH 0/2 v6] Lattice MachXO2 Slave SPI FPGA Manager support Paolo Pisati 2018-03-16 15:54 ` [PATCH 1/2] dt: bindings: fpga: add lattice machxo2 slave spi binding description Paolo Pisati 2018-03-16 16:31 ` Moritz Fischer 2018-03-19 15:42 ` Alan Tull 2018-03-16 15:54 ` [PATCH 2/2] fpga: lattice machxo2: Add Lattice MachXO2 support Paolo Pisati 2018-03-16 16:26 ` Moritz Fischer 2018-03-19 18:09 ` Paolo Pisati -- strict thread matches above, loose matches on Subject: below -- 2018-03-23 12:27 [PATCH 0/2 v8] Lattice MachXO2 Slave SPI FPGA Manager support Paolo Pisati 2018-03-23 12:27 ` [PATCH 1/2] dt: bindings: fpga: add lattice machxo2 slave spi binding description Paolo Pisati 2018-03-21 17:35 [PATCH 0/2 v7] Lattice MachXO2 Slave SPI FPGA Manager support Paolo Pisati 2018-03-21 17:35 ` [PATCH 1/2] dt: bindings: fpga: add lattice machxo2 slave spi binding description Paolo Pisati 2017-07-06 10:01 [PATCH v5 0/2] Lattice MachXO2 Slave SPI FPGA Manager support Paolo Pisati 2017-07-06 10:01 ` [PATCH 1/2] dt: bindings: fpga: add lattice machxo2 slave spi binding description Paolo Pisati 2017-04-23 15:20 [PATCH 0/2] Lattice MachXO2 Passive SPI FPGA Manager support Paolo Pisati 2017-04-23 15:20 ` [PATCH 1/2] dt: bindings: fpga: add lattice machxo2 slave spi binding description Paolo Pisati 2017-04-28 17:54 ` Rob Herring
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).