On Tue, Apr 03, 2018 at 06:44:46PM +0300, Sergey Suloev wrote:
> There is no need to handle 3/4 empty interrupt as the maximum
> supported transfer length in PIO mode is equal to FIFO depth,
> i.e. 128 bytes for sun6i and 64 bytes for sun8i SoCs.
>
> Changes in v3:
> 1) Restored processing of 3/4 FIFO full interrupt.
> 
> Signed-off-by: Sergey Suloev <ssuloev@orpaltech.com>
> ---
>  drivers/spi/spi-sun6i.c | 41 +++++++++++++++++------------------------
>  1 file changed, 17 insertions(+), 24 deletions(-)
> 
> diff --git a/drivers/spi/spi-sun6i.c b/drivers/spi/spi-sun6i.c
> index 78acc1f..c09ad10 100644
> --- a/drivers/spi/spi-sun6i.c
> +++ b/drivers/spi/spi-sun6i.c
> @@ -207,7 +207,10 @@ static void sun6i_spi_set_cs(struct spi_device *spi, bool enable)
>  
>  static size_t sun6i_spi_max_transfer_size(struct spi_device *spi)
>  {
> -	return SUN6I_MAX_XFER_SIZE - 1;
> +	struct spi_master *master = spi->master;
> +	struct sun6i_spi *sspi = spi_master_get_devdata(master);
> +
> +	return sspi->fifo_depth;

Doesn't that effectively revert 3288d5cb40c0 ?

Why do you need to do so?

>  }
>  
>  static int sun6i_spi_prepare_message(struct spi_master *master,
> @@ -255,8 +258,14 @@ static int sun6i_spi_transfer_one(struct spi_master *master,
>  	int ret = 0;
>  	u32 reg;
>  
> -	if (tfr->len > SUN6I_MAX_XFER_SIZE)
> -		return -EINVAL;
> +	/* A zero length transfer never finishes if programmed
> +	   in the hardware */

Improper comment style here. Please make sure to run checkpatch before
sending your patches.

> +	if (!tfr->len)
> +		return 0;

Can that case even happen?

> +	/* Don't support transfer larger than the FIFO */
> +	if (tfr->len > sspi->fifo_depth)
> +		return -EMSGSIZE;

You're changing the return type, why?

>  	reinit_completion(&sspi->done);
>  	sspi->tx_buf = tfr->tx_buf;
> @@ -278,8 +287,7 @@ static int sun6i_spi_transfer_one(struct spi_master *master,
>  	 */
>  	trig_level = sspi->fifo_depth / 4 * 3;
>  	sun6i_spi_write(sspi, SUN6I_FIFO_CTL_REG,
> -			(trig_level << SUN6I_FIFO_CTL_RF_RDY_TRIG_LEVEL_BITS) |
> -			(trig_level << SUN6I_FIFO_CTL_TF_ERQ_TRIG_LEVEL_BITS));
> +			(trig_level << SUN6I_FIFO_CTL_RF_RDY_TRIG_LEVEL_BITS));
>  
>  
>  	reg = sun6i_spi_read(sspi, SUN6I_TFR_CTL_REG);
> @@ -343,11 +351,8 @@ static int sun6i_spi_transfer_one(struct spi_master *master,
>  	sun6i_spi_fill_fifo(sspi, sspi->fifo_depth);
>  
>  	/* Enable the interrupts */
> -	sun6i_spi_write(sspi, SUN6I_INT_CTL_REG, SUN6I_INT_CTL_TC);
>  	sun6i_spi_enable_interrupt(sspi, SUN6I_INT_CTL_TC |
>  					 SUN6I_INT_CTL_RF_RDY);
> -	if (tx_len > sspi->fifo_depth)
> -		sun6i_spi_enable_interrupt(sspi, SUN6I_INT_CTL_TF_ERQ);

This would also need to be explained in your commit log.

>  
>  	/* Start the transfer */
>  	reg = sun6i_spi_read(sspi, SUN6I_TFR_CTL_REG);
> @@ -376,7 +381,9 @@ out:
>  static irqreturn_t sun6i_spi_handler(int irq, void *dev_id)
>  {
>  	struct sun6i_spi *sspi = dev_id;
> -	u32 status = sun6i_spi_read(sspi, SUN6I_INT_STA_REG);
> +	u32 status;
> +
> +	status = sun6i_spi_read(sspi, SUN6I_INT_STA_REG);

Why is this change needed?

Maxime

-- 
Maxime Ripard, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
https://bootlin.com