[Patch v15 4/5] dt-bindings: arm-smmu: Add bindings for qcom,smmu-v2

[Vivek Gautam <vivek.gautam@codeaurora.org>]

Add bindings doc for Qcom's smmu-v2 implementation.

Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---

Changes since v14:
 - This is a new patch added in v15 after noticing the new
   checkpatch warning for separate dt-bindings doc.
 - This patch also addresses comments given by Rob and Robin to add
   a list of valid values of '<soc>' in "qcom,<soc>-smmu-v2"
   compatible string.

 .../devicetree/bindings/iommu/arm,smmu.txt         | 47 ++++++++++++++++++++++
 1 file changed, 47 insertions(+)

diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu.txt b/Documentation/devicetree/bindings/iommu/arm,smmu.txt
index 8a6ffce12af5..52198a539606 100644
--- a/Documentation/devicetree/bindings/iommu/arm,smmu.txt
+++ b/Documentation/devicetree/bindings/iommu/arm,smmu.txt
@@ -17,10 +17,24 @@ conditions.
                         "arm,mmu-401"
                         "arm,mmu-500"
                         "cavium,smmu-v2"
+                        "qcom,<soc>-smmu-v2", "qcom,smmu-v2"
 
                   depending on the particular implementation and/or the
                   version of the architecture implemented.
 
+                  A number of Qcom SoCs use qcom,smmu-v2 version of the IP.
+                  "qcom,<soc>-smmu-v2" represents a soc specific compatible
+                  string that should be present along with the "qcom,smmu-v2"
+                  to facilitate SoC specific clocks/power connections and to
+                  address specific bug fixes.
+                  '<soc>' string in "qcom,<soc>-smmu-v2" should be one of the
+                  following:
+                  msm8996 - for msm8996 Qcom SoC.
+                  sdm845 - for sdm845 Qcom Soc.
+
+                  An example string would be -
+                  "qcom,msm8996-smmu-v2", "qcom,smmu-v2".
+
 - reg           : Base address and size of the SMMU.
 
 - #global-interrupts : The number of global interrupts exposed by the
@@ -71,6 +85,22 @@ conditions.
                   or using stream matching with #iommu-cells = <2>, and
                   may be ignored if present in such cases.
 
+- clock-names:    List of the names of clocks input to the device. The
+                  required list depends on particular implementation and
+                  is as follows:
+                  - for "qcom,smmu-v2":
+                    - "bus": clock required for downstream bus access and
+                             for the smmu ptw,
+                    - "iface": clock required to access smmu's registers
+                               through the TCU's programming interface.
+                  - unspecified for other implementations.
+
+- clocks:         Specifiers for all clocks listed in the clock-names property,
+                  as per generic clock bindings.
+
+- power-domains:  Specifiers for power domains required to be powered on for
+                  the SMMU to operate, as per generic power domain bindings.
+
 ** Deprecated properties:
 
 - mmu-masters (deprecated in favour of the generic "iommus" binding) :
@@ -137,3 +167,20 @@ conditions.
                 iommu-map = <0 &smmu3 0 0x400>;
                 ...
         };
+
+	/* Qcom's arm,smmu-v2 implementation */
+	smmu4: iommu {
+		compatible = "qcom,msm8996-smmu-v2", "qcom,smmu-v2";
+		reg = <0xd00000 0x10000>;
+
+		#global-interrupts = <1>;
+		interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>;
+		#iommu-cells = <1>;
+		power-domains = <&mmcc MDSS_GDSC>;
+
+		clocks = <&mmcc SMMU_MDP_AXI_CLK>,
+			 <&mmcc SMMU_MDP_AHB_CLK>;
+		clock-names = "bus", "iface";
+	};
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation