From: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
To: xuwei5@hisilicon.com, linus.walleij@linaro.org, robh+dt@kernel.org
Cc: linux-gpio@vger.kernel.org, devicetree@vger.kernel.org,
amit.kucheria@linaro.org, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org,
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Subject: [PATCH 3/5] arm64: dts: hisilicon: hi3670: Add UART nodes
Date: Wed, 24 Oct 2018 00:36:53 +0530 [thread overview]
Message-ID: <20181023190655.12004-4-manivannan.sadhasivam@linaro.org> (raw)
In-Reply-To: <20181023190655.12004-1-manivannan.sadhasivam@linaro.org>
Add UART nodes for HiSilicon HI3670 SoC and also relevant pinmux/pinconf
entries.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
arch/arm64/boot/dts/hisilicon/hi3670.dtsi | 72 ++++++++
.../boot/dts/hisilicon/hikey970-pinctrl.dtsi | 157 ++++++++++++++++++
2 files changed, 229 insertions(+)
diff --git a/arch/arm64/boot/dts/hisilicon/hi3670.dtsi b/arch/arm64/boot/dts/hisilicon/hi3670.dtsi
index b99f5e0fe577..a5bd6d80b226 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3670.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi3670.dtsi
@@ -187,6 +187,76 @@
#clock-cells = <1>;
};
+ uart0: serial@fdf02000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0 0xfdf02000 0x0 0x1000>;
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg_ctrl HI3670_CLK_GATE_UART0>,
+ <&crg_ctrl HI3670_PCLK>;
+ clock-names = "uartclk", "apb_pclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pmx_func &uart0_cfg_func>;
+ status = "disabled";
+ };
+
+ uart1: serial@fdf00000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0 0xfdf00000 0x0 0x1000>;
+ interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg_ctrl HI3670_CLK_GATE_UART1>,
+ <&crg_ctrl HI3670_PCLK>;
+ clock-names = "uartclk", "apb_pclk";
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ uart2: serial@fdf03000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0 0xfdf03000 0x0 0x1000>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg_ctrl HI3670_CLK_GATE_UART2>,
+ <&crg_ctrl HI3670_PCLK>;
+ clock-names = "uartclk", "apb_pclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pmx_func &uart2_cfg_func>;
+ status = "disabled";
+ };
+
+ uart3: serial@ffd74000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0 0xffd74000 0x0 0x1000>;
+ interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg_ctrl HI3670_CLK_GATE_UART3>,
+ <&crg_ctrl HI3670_PCLK>;
+ clock-names = "uartclk", "apb_pclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pmx_func &uart3_cfg_func>;
+ status = "disabled";
+ };
+
+ uart4: serial@fdf01000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0 0xfdf01000 0x0 0x1000>;
+ interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg_ctrl HI3670_CLK_GATE_UART4>,
+ <&crg_ctrl HI3670_PCLK>;
+ clock-names = "uartclk", "apb_pclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pmx_func &uart4_cfg_func>;
+ status = "disabled";
+ };
+
+ uart5: serial@fdf05000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0 0xfdf05000 0x0 0x1000>;
+ interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg_ctrl HI3670_CLK_GATE_UART5>,
+ <&crg_ctrl HI3670_PCLK>;
+ clock-names = "uartclk", "apb_pclk";
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
uart6: serial@fff32000 {
compatible = "arm,pl011", "arm,primecell";
reg = <0x0 0xfff32000 0x0 0x1000>;
@@ -194,6 +264,8 @@
clocks = <&crg_ctrl HI3670_CLK_UART6>,
<&crg_ctrl HI3670_PCLK>;
clock-names = "uartclk", "apb_pclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart6_pmx_func &uart6_cfg_func>;
status = "disabled";
};
diff --git a/arch/arm64/boot/dts/hisilicon/hikey970-pinctrl.dtsi b/arch/arm64/boot/dts/hisilicon/hikey970-pinctrl.dtsi
index 64fb9a3bd707..67bb52d43619 100644
--- a/arch/arm64/boot/dts/hisilicon/hikey970-pinctrl.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hikey970-pinctrl.dtsi
@@ -20,6 +20,47 @@
pinctrl-single,function-mask = <0x7>;
/* pin base, nr pins & gpio function */
pinctrl-single,gpio-range = <&range 0 82 0>;
+
+ uart0_pmx_func: uart0_pmx_func {
+ pinctrl-single,pins = <
+ 0x054 MUX_M2 /* UART0_RXD */
+ 0x058 MUX_M2 /* UART0_TXD */
+ >;
+ };
+
+ uart2_pmx_func: uart2_pmx_func {
+ pinctrl-single,pins = <
+ 0x700 MUX_M2 /* UART2_CTS_N */
+ 0x704 MUX_M2 /* UART2_RTS_N */
+ 0x708 MUX_M2 /* UART2_RXD */
+ 0x70c MUX_M2 /* UART2_TXD */
+ >;
+ };
+
+ uart3_pmx_func: uart3_pmx_func {
+ pinctrl-single,pins = <
+ 0x064 MUX_M1 /* UART3_CTS_N */
+ 0x068 MUX_M1 /* UART3_RTS_N */
+ 0x06c MUX_M1 /* UART3_RXD */
+ 0x070 MUX_M1 /* UART3_TXD */
+ >;
+ };
+
+ uart4_pmx_func: uart4_pmx_func {
+ pinctrl-single,pins = <
+ 0x074 MUX_M1 /* UART4_CTS_N */
+ 0x078 MUX_M1 /* UART4_RTS_N */
+ 0x07c MUX_M1 /* UART4_RXD */
+ 0x080 MUX_M1 /* UART4_TXD */
+ >;
+ };
+
+ uart6_pmx_func: uart6_pmx_func {
+ pinctrl-single,pins = <
+ 0x05c MUX_M1 /* UART6_RXD */
+ 0x060 MUX_M1 /* UART6_TXD */
+ >;
+ };
};
pmx2: pinmux@e896c800 {
@@ -27,6 +68,122 @@
reg = <0x0 0xe896c800 0x0 0x72c>;
#pinctrl-cells = <1>;
pinctrl-single,register-width = <0x20>;
+
+ uart0_cfg_func: uart0_cfg_func {
+ pinctrl-single,pins = <
+ 0x058 0x0 /* UART0_RXD */
+ 0x05c 0x0 /* UART0_TXD */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_DIS
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE7_04MA DRIVE6_MASK
+ >;
+ };
+
+ uart2_cfg_func: uart2_cfg_func {
+ pinctrl-single,pins = <
+ 0x700 0x0 /* UART2_CTS_N */
+ 0x704 0x0 /* UART2_RTS_N */
+ 0x708 0x0 /* UART2_RXD */
+ 0x70c 0x0 /* UART2_TXD */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_DIS
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE7_04MA DRIVE6_MASK
+ >;
+ };
+
+ uart3_cfg_func: uart3_cfg_func {
+ pinctrl-single,pins = <
+ 0x068 0x0 /* UART3_CTS_N */
+ 0x06c 0x0 /* UART3_RTS_N */
+ 0x070 0x0 /* UART3_RXD */
+ 0x074 0x0 /* UART3_TXD */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_DIS
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE7_04MA DRIVE6_MASK
+ >;
+ };
+
+ uart4_cfg_func: uart4_cfg_func {
+ pinctrl-single,pins = <
+ 0x078 0x0 /* UART4_CTS_N */
+ 0x07c 0x0 /* UART4_RTS_N */
+ 0x080 0x0 /* UART4_RXD */
+ 0x084 0x0 /* UART4_TXD */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_DIS
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE7_04MA DRIVE6_MASK
+ >;
+ };
+
+ uart6_cfg_func: uart6_cfg_func {
+ pinctrl-single,pins = <
+ 0x060 0x0 /* UART6_RXD */
+ 0x064 0x0 /* UART6_TXD */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_DIS
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE7_02MA DRIVE6_MASK
+ >;
+ };
};
pmx5: pinmux@fc182000 {
--
2.17.1
next prev parent reply other threads:[~2018-10-23 19:07 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-10-23 19:06 [PATCH 0/5] Add Pinctrl and GPIO support for HI3670 SoC Manivannan Sadhasivam
2018-10-23 19:06 ` [PATCH 1/5] arm64: dts: hisilicon: Add Pinctrl support for HiKey970 board Manivannan Sadhasivam
2018-10-23 19:06 ` [PATCH 2/5] arm64: dts: hisilicon: hi3760: Add GPIO controller support Manivannan Sadhasivam
2018-10-23 19:06 ` Manivannan Sadhasivam [this message]
2018-10-23 19:06 ` [PATCH 4/5] arm64: boot: dts: hisilicon: hikey970: Enable on-board UARTs Manivannan Sadhasivam
2018-10-23 19:06 ` [PATCH 5/5] arm64: dts: hisilicon: hikey970: Add GPIO line names Manivannan Sadhasivam
2018-10-31 9:43 ` [PATCH 0/5] Add Pinctrl and GPIO support for HI3670 SoC Linus Walleij
2018-11-12 7:17 ` Manivannan Sadhasivam
2018-11-29 15:29 ` Wei Xu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181023190655.12004-4-manivannan.sadhasivam@linaro.org \
--to=manivannan.sadhasivam@linaro.org \
--cc=amit.kucheria@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=xuwei5@hisilicon.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).