From: Douglas Anderson <dianders@chromium.org>
To: Sean Paul <seanpaul@chromium.org>,
Thierry Reding <thierry.reding@gmail.com>,
Sandeep Panda <spanda@codeaurora.org>
Cc: linux-arm-msm@vger.kernel.org,
Laurent Pinchart <laurent.pinchart@ideasonboard.com>,
jsanka@codeaurora.org, ryandcase@chromium.org,
Douglas Anderson <dianders@chromium.org>,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
dri-devel@lists.freedesktop.org, Rob Herring <robh+dt@kernel.org>,
David Airlie <airlied@linux.ie>,
Mark Rutland <mark.rutland@arm.com>
Subject: [PATCH v2 1/6] dt-bindings: drm/panel: simple: Add no-hpd property
Date: Thu, 25 Oct 2018 15:21:29 -0700 [thread overview]
Message-ID: <20181025222134.174583-1-dianders@chromium.org> (raw)
Some eDP panels that are designed to be always connected to a board
use their HPD signal to signal that they've finished powering on and
they're ready to be talked to.
However, for various reasons it's possible that the HPD signal from
the panel isn't actually hooked up. In the case where the HPD isn't
hooked up you can look at the timing diagram on the panel datasheet
and insert a delay for the maximum amount of time that the HPD might
take to come up.
Let's add a property in the device tree for this concept.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Sean Paul <sean@poorly.run>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Changes in v2: None
.../devicetree/bindings/display/panel/simple-panel.txt | 3 +++
1 file changed, 3 insertions(+)
diff --git a/Documentation/devicetree/bindings/display/panel/simple-panel.txt b/Documentation/devicetree/bindings/display/panel/simple-panel.txt
index 45a457ad38f0..b2b872c710f2 100644
--- a/Documentation/devicetree/bindings/display/panel/simple-panel.txt
+++ b/Documentation/devicetree/bindings/display/panel/simple-panel.txt
@@ -11,6 +11,9 @@ Optional properties:
- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
- enable-gpios: GPIO pin to enable or disable the panel
- backlight: phandle of the backlight device attached to the panel
+- no-hpd: This panel is supposed to communicate that it's ready via HPD
+ (hot plug detect) signal, but the signal isn't hooked up so we should
+ hardcode the max delay from the panel spec when powering up the panel.
Example:
--
2.19.1.568.g152ad8e336-goog
next reply other threads:[~2018-10-25 22:22 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-10-25 22:21 Douglas Anderson [this message]
2018-10-25 22:21 ` [PATCH v2 2/6] drm/panel: simple: Support panels with HPD where HPD isn't connected Douglas Anderson
2018-10-26 14:41 ` Sean Paul
2018-10-25 22:21 ` [PATCH v2 3/6] drm/panel: simple: Add "no-hpd" delay for Innolux TV123WAM Douglas Anderson
2018-10-26 14:41 ` Sean Paul
2018-10-25 22:21 ` [PATCH v2 4/6] drm/bridge: ti-sn65dsi86: Remove the mystery delay Douglas Anderson
2018-10-29 9:03 ` Andrzej Hajda
2018-10-25 22:21 ` [PATCH v2 5/6] dt-bindings: drm/panel: simple: Innolux TV123WAM is actually P120ZDG-BF1 Douglas Anderson
2018-10-26 14:43 ` Sean Paul
2018-10-26 14:46 ` Sean Paul
2018-10-26 15:01 ` Doug Anderson
2018-10-29 9:10 ` Andrzej Hajda
2018-10-25 22:21 ` [PATCH v2 6/6] " Douglas Anderson
2018-10-26 14:44 ` Sean Paul
2018-10-29 16:16 ` [PATCH v2 1/6] dt-bindings: drm/panel: simple: Add no-hpd property Sean Paul
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181025222134.174583-1-dianders@chromium.org \
--to=dianders@chromium.org \
--cc=airlied@linux.ie \
--cc=devicetree@vger.kernel.org \
--cc=dri-devel@lists.freedesktop.org \
--cc=jsanka@codeaurora.org \
--cc=laurent.pinchart@ideasonboard.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=ryandcase@chromium.org \
--cc=seanpaul@chromium.org \
--cc=spanda@codeaurora.org \
--cc=thierry.reding@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).