[PATCH v6 0/9] EDAC drivers for Armada XP L2 and DDR

[PATCH v6 0/9] EDAC drivers for Armada XP L2 and DDR

[Chris Packham]

The current plan is for these to go in via the ARM tree once appropriate
Reviews/Acks have been given

http://lists.infradead.org/pipermail/linux-arm-kernel/2017-August/525561.html

This series adds drivers for the L2 cache and DDR RAM ECC functionality as
found on the MV78230/MV78x60 SoCs. Jan has tested these changes with the
MV78460 (on a custom board with a DDR3 ECC DIMM), Chris has tested these
changes with 88F6820 and 98dx3236 (both a custom boards with fixed DDR3 + ECC).

Also contained in this series is an additional debugfs wrapper.

Compared to the previous v5 series I've split the dt-binding documentation into
its own patch and updated armada_xp_edac.c to use a SPDX license.

Compared to the previous v4 series I've added my s-o-b to some of Jan's
patches and rebased against v4.19.0.

Compared to the previous v3 series, the following changes have been made:
- Use shorter names for the AURORA ECC and parity registers
- Numerous formatting changes to edac/armada_xp.c (as requested by Boris)
- Added support for Armada-38x and 98dx3236 SoCs

Compared to the previous v2 series, the following changes have been made:
- Allocate EDAC structures later during probing and drop devres support
  patches (requested by Boris)
- Make drvdata->width usage consistent according to the comment (suggested by
  Chris)

Compared to the previous v1 series, the following changes have been made:
- Add the aurora-l2 register defines earlier in the series (suggested by
  Russell King and Gregory CLEMENT )
- Changed the DT vendor prefix from "arm" to "marvell" for the ecc-enable/disable
  properties on the aurora-l2 (suggested by Russell King)
- Fix some warnings reported by checkpatch

Compared to the original RFC series, the following changes have been made:
- Integrated Chris' patches for parity and ECC configuration via DT
- Merged the DDR RAM and L2 cache drivers (as requested by Boris, analogous
  to fsl_ddr_edac.c and mpc85xx_edac.c)
- Added myself to MAINTAINERS (requested by Boris)
- L2 cache: Track the msg size and use snprintf (review comment by Chris)
- L2 cache: Split error injection from the check function (review comment by
  Chris)
- DDR RAM: Allow 16 bit width in addition to 32 and 64 bit (review comment by
  Chris)
- Use of_match_ptr() (review comments by Chris)
- Minor checkpatch cleanups

Chris Packham (4):
  ARM: l2x0: support parity-enable/disable on aurora
  dt-bindings: ARM: document marvell,ecc-enable binding
  ARM: l2x0: add marvell,ecc-enable property for aurora
  EDAC: armada_xp: Add support for more SoCs

Jan Luebbe (5):
  ARM: l2c: move cache-aurora-l2.h to asm/hardware
  ARM: aurora-l2: add prefix to MAX_RANGE_SIZE
  ARM: aurora-l2: add defines for parity and ECC registers
  EDAC: Add missing debugfs_create_x32 wrapper
  EDAC: Add driver for the Marvell Armada XP SDRAM and L2 cache ECC

 .../devicetree/bindings/arm/l2c2x0.txt        |   2 +
 MAINTAINERS                                   |   6 +
 .../asm/hardware}/cache-aurora-l2.h           |  50 +-
 arch/arm/mm/cache-l2x0.c                      |  20 +-
 drivers/edac/Kconfig                          |   7 +
 drivers/edac/Makefile                         |   1 +
 drivers/edac/armada_xp_edac.c                 | 635 ++++++++++++++++++
 drivers/edac/debugfs.c                        |  11 +
 drivers/edac/edac_module.h                    |   5 +
 9 files changed, 733 insertions(+), 4 deletions(-)
 rename arch/arm/{mm => include/asm/hardware}/cache-aurora-l2.h (50%)
 create mode 100644 drivers/edac/armada_xp_edac.c

-- 
2.19.1

[PATCH v6 1/9] ARM: l2c: move cache-aurora-l2.h to asm/hardware

[Chris Packham]

From: Jan Luebbe <jlu@pengutronix.de>

This include file will be used by the AURORA EDAC code.

Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
 arch/arm/{mm => include/asm/hardware}/cache-aurora-l2.h | 0
 arch/arm/mm/cache-l2x0.c                                | 2 +-
 2 files changed, 1 insertion(+), 1 deletion(-)
 rename arch/arm/{mm => include/asm/hardware}/cache-aurora-l2.h (100%)

diff --git a/arch/arm/mm/cache-aurora-l2.h b/arch/arm/include/asm/hardware/cache-aurora-l2.h
similarity index 100%
rename from arch/arm/mm/cache-aurora-l2.h
rename to arch/arm/include/asm/hardware/cache-aurora-l2.h
diff --git a/arch/arm/mm/cache-l2x0.c b/arch/arm/mm/cache-l2x0.c
index 808efbb89b88..a00d6f7fd34c 100644
--- a/arch/arm/mm/cache-l2x0.c
+++ b/arch/arm/mm/cache-l2x0.c
@@ -30,8 +30,8 @@
 #include <asm/cp15.h>
 #include <asm/cputype.h>
 #include <asm/hardware/cache-l2x0.h>
+#include <asm/hardware/cache-aurora-l2.h>
 #include "cache-tauros3.h"
-#include "cache-aurora-l2.h"
 
 struct l2c_init_data {
 	const char *type;
-- 
2.19.1

[PATCH v6 2/9] ARM: aurora-l2: add prefix to MAX_RANGE_SIZE

[Chris Packham]

From: Jan Luebbe <jlu@pengutronix.de>

The macro name is too generic, so add a AURORA_ prefix.

Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
 arch/arm/include/asm/hardware/cache-aurora-l2.h | 2 +-
 arch/arm/mm/cache-l2x0.c                        | 4 ++--
 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/include/asm/hardware/cache-aurora-l2.h b/arch/arm/include/asm/hardware/cache-aurora-l2.h
index c86124769831..dc5c479ec4c3 100644
--- a/arch/arm/include/asm/hardware/cache-aurora-l2.h
+++ b/arch/arm/include/asm/hardware/cache-aurora-l2.h
@@ -41,7 +41,7 @@
 #define AURORA_ACR_FORCE_WRITE_THRO_POLICY	\
 	(2 << AURORA_ACR_FORCE_WRITE_POLICY_OFFSET)
 
-#define MAX_RANGE_SIZE		1024
+#define AURORA_MAX_RANGE_SIZE	1024
 
 #define AURORA_WAY_SIZE_SHIFT	2
 
diff --git a/arch/arm/mm/cache-l2x0.c b/arch/arm/mm/cache-l2x0.c
index a00d6f7fd34c..7d2d2a3c67d0 100644
--- a/arch/arm/mm/cache-l2x0.c
+++ b/arch/arm/mm/cache-l2x0.c
@@ -1364,8 +1364,8 @@ static unsigned long aurora_range_end(unsigned long start, unsigned long end)
 	 * since cache range operations stall the CPU pipeline
 	 * until completion.
 	 */
-	if (end > start + MAX_RANGE_SIZE)
-		end = start + MAX_RANGE_SIZE;
+	if (end > start + AURORA_MAX_RANGE_SIZE)
+		end = start + AURORA_MAX_RANGE_SIZE;
 
 	/*
 	 * Cache range operations can't straddle a page boundary.
-- 
2.19.1

[PATCH v6 3/9] ARM: aurora-l2: add defines for parity and ECC registers

[Chris Packham]

From: Jan Luebbe <jlu@pengutronix.de>

These defines will be used by subsequent patches to add support for the
parity check and error correction functionality in the Aurora L2 cache
controller.

Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
 .../include/asm/hardware/cache-aurora-l2.h    | 48 +++++++++++++++++++
 1 file changed, 48 insertions(+)

diff --git a/arch/arm/include/asm/hardware/cache-aurora-l2.h b/arch/arm/include/asm/hardware/cache-aurora-l2.h
index dc5c479ec4c3..39769ffa0051 100644
--- a/arch/arm/include/asm/hardware/cache-aurora-l2.h
+++ b/arch/arm/include/asm/hardware/cache-aurora-l2.h
@@ -31,6 +31,9 @@
 #define AURORA_ACR_REPLACEMENT_TYPE_SEMIPLRU \
 	(3 << AURORA_ACR_REPLACEMENT_OFFSET)
 
+#define AURORA_ACR_PARITY_EN	(1 << 21)
+#define AURORA_ACR_ECC_EN	(1 << 20)
+
 #define AURORA_ACR_FORCE_WRITE_POLICY_OFFSET	0
 #define AURORA_ACR_FORCE_WRITE_POLICY_MASK	\
 	(0x3 << AURORA_ACR_FORCE_WRITE_POLICY_OFFSET)
@@ -41,6 +44,51 @@
 #define AURORA_ACR_FORCE_WRITE_THRO_POLICY	\
 	(2 << AURORA_ACR_FORCE_WRITE_POLICY_OFFSET)
 
+#define AURORA_ERR_CNT_REG          0x600
+#define AURORA_ERR_ATTR_CAP_REG     0x608
+#define AURORA_ERR_ADDR_CAP_REG     0x60c
+#define AURORA_ERR_WAY_CAP_REG      0x610
+#define AURORA_ERR_INJECT_CTL_REG   0x614
+#define AURORA_ERR_INJECT_MASK_REG  0x618
+
+#define AURORA_ERR_CNT_CLR_OFFSET         31
+#define AURORA_ERR_CNT_CLR		   \
+	(0x1 << AURORA_ERR_CNT_CLR_OFFSET)
+#define AURORA_ERR_CNT_UE_OFFSET          16
+#define AURORA_ERR_CNT_UE_MASK             \
+	(0x7fff << AURORA_ERR_CNT_UE_OFFSET)
+#define AURORA_ERR_CNT_CE_OFFSET           0
+#define AURORA_ERR_CNT_CE_MASK             \
+	(0xffff << AURORA_ERR_CNT_CE_OFFSET)
+
+#define AURORA_ERR_ATTR_SRC_OFF           16
+#define AURORA_ERR_ATTR_SRC_MSK            \
+	(0x7 << AURORA_ERR_ATTR_SRC_OFF)
+#define AURORA_ERR_ATTR_TXN_OFF           12
+#define AURORA_ERR_ATTR_TXN_MSK            \
+	(0xf << AURORA_ERR_ATTR_TXN_OFF)
+#define AURORA_ERR_ATTR_ERR_OFF            8
+#define AURORA_ERR_ATTR_ERR_MSK            \
+	(0x3 << AURORA_ERR_ATTR_ERR_OFF)
+#define AURORA_ERR_ATTR_CAP_VALID_OFF      0
+#define AURORA_ERR_ATTR_CAP_VALID          \
+	(0x1 << AURORA_ERR_ATTR_CAP_VALID_OFF)
+
+#define AURORA_ERR_ADDR_CAP_ADDR_MASK 0xffffffe0
+
+#define AURORA_ERR_WAY_IDX_OFF             8
+#define AURORA_ERR_WAY_IDX_MSK             \
+	(0xfff << AURORA_ERR_WAY_IDX_OFF)
+#define AURORA_ERR_WAY_CAP_WAY_OFFSET      1
+#define AURORA_ERR_WAY_CAP_WAY_MASK        \
+	(0xf << AURORA_ERR_WAY_CAP_WAY_OFFSET)
+
+#define AURORA_ERR_INJECT_CTL_ADDR_MASK 0xfffffff0
+#define AURORA_ERR_ATTR_TXN_OFF   12
+#define AURORA_ERR_INJECT_CTL_EN_MASK          0x3
+#define AURORA_ERR_INJECT_CTL_EN_PARITY        0x2
+#define AURORA_ERR_INJECT_CTL_EN_ECC           0x1
+
 #define AURORA_MAX_RANGE_SIZE	1024
 
 #define AURORA_WAY_SIZE_SHIFT	2
-- 
2.19.1

[PATCH v6 4/9] ARM: l2x0: support parity-enable/disable on aurora

[Chris Packham]

The aurora cache on the Marvell Armada-XP SoC supports the same tag
parity features as the other l2x0 cache implementations.

Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[jlu@pengutronix.de: use aurora specific define AURORA_ACR_PARITY_EN]
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
---
 arch/arm/mm/cache-l2x0.c | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm/mm/cache-l2x0.c b/arch/arm/mm/cache-l2x0.c
index 7d2d2a3c67d0..b70bee74750d 100644
--- a/arch/arm/mm/cache-l2x0.c
+++ b/arch/arm/mm/cache-l2x0.c
@@ -1505,6 +1505,13 @@ static void __init aurora_of_parse(const struct device_node *np,
 		mask |= AURORA_ACR_FORCE_WRITE_POLICY_MASK;
 	}
 
+	if (of_property_read_bool(np, "arm,parity-enable")) {
+		mask |= AURORA_ACR_PARITY_EN;
+		val |= AURORA_ACR_PARITY_EN;
+	} else if (of_property_read_bool(np, "arm,parity-disable")) {
+		mask |= AURORA_ACR_PARITY_EN;
+	}
+
 	*aux_val &= ~mask;
 	*aux_val |= val;
 	*aux_mask &= ~mask;
-- 
2.19.1

[PATCH v6 5/9] dt-bindings: ARM: document marvell,ecc-enable binding

[Chris Packham]

Add documentation for the marvell,ecc-enable and marvell,ecc-disable
properties which can be used to enable/disable ECC on the Marvell aurora
cache.

Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---

Notes:
    Changes in v6:
    - new (split binding doc from implementation).

 Documentation/devicetree/bindings/arm/l2c2x0.txt | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/l2c2x0.txt b/Documentation/devicetree/bindings/arm/l2c2x0.txt
index fbe6cb21f4cf..15a84f0ba9f1 100644
--- a/Documentation/devicetree/bindings/arm/l2c2x0.txt
+++ b/Documentation/devicetree/bindings/arm/l2c2x0.txt
@@ -76,6 +76,8 @@ Optional properties:
   specified to indicate that such transforms are precluded.
 - arm,parity-enable : enable parity checking on the L2 cache (L220 or PL310).
 - arm,parity-disable : disable parity checking on the L2 cache (L220 or PL310).
+- marvell,ecc-enable : enable ECC protection on the L2 cache
+- marvell,ecc-disable : disable ECC protection on the L2 cache
 - arm,outer-sync-disable : disable the outer sync operation on the L2 cache.
   Some core tiles, especially ARM PB11MPCore have a faulty L220 cache that
   will randomly hang unless outer sync operations are disabled.
-- 
2.19.1

[PATCH v6 6/9] ARM: l2x0: add marvell,ecc-enable property for aurora

[Chris Packham]

The aurora cache on the Marvell Armada-XP SoC supports ECC protection
for the L2 data arrays. Add a "marvell,ecc-enable" device tree property
which can be used to enable this.

Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[jlu@pengutronix.de: use aurora specific define AURORA_ACR_ECC_EN]
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
---
 arch/arm/mm/cache-l2x0.c | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm/mm/cache-l2x0.c b/arch/arm/mm/cache-l2x0.c
index b70bee74750d..644f786e4fa9 100644
--- a/arch/arm/mm/cache-l2x0.c
+++ b/arch/arm/mm/cache-l2x0.c
@@ -1505,6 +1505,13 @@ static void __init aurora_of_parse(const struct device_node *np,
 		mask |= AURORA_ACR_FORCE_WRITE_POLICY_MASK;
 	}
 
+	if (of_property_read_bool(np, "marvell,ecc-enable")) {
+		mask |= AURORA_ACR_ECC_EN;
+		val |= AURORA_ACR_ECC_EN;
+	} else if (of_property_read_bool(np, "marvell,ecc-disable")) {
+		mask |= AURORA_ACR_ECC_EN;
+	}
+
 	if (of_property_read_bool(np, "arm,parity-enable")) {
 		mask |= AURORA_ACR_PARITY_EN;
 		val |= AURORA_ACR_PARITY_EN;
-- 
2.19.1

[PATCH v6 7/9] EDAC: Add missing debugfs_create_x32 wrapper

[Chris Packham]

From: Jan Luebbe <jlu@pengutronix.de>

We already have wrappers for x8 and x16, so add the missing x32 one.

Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
 drivers/edac/debugfs.c     | 11 +++++++++++
 drivers/edac/edac_module.h |  5 +++++
 2 files changed, 16 insertions(+)

diff --git a/drivers/edac/debugfs.c b/drivers/edac/debugfs.c
index 92dbb7e2320c..268ede7a60b2 100644
--- a/drivers/edac/debugfs.c
+++ b/drivers/edac/debugfs.c
@@ -161,3 +161,14 @@ struct dentry *edac_debugfs_create_x16(const char *name, umode_t mode,
 	return debugfs_create_x16(name, mode, parent, value);
 }
 EXPORT_SYMBOL_GPL(edac_debugfs_create_x16);
+
+/* Wrapper for debugfs_create_x32() */
+struct dentry *edac_debugfs_create_x32(const char *name, umode_t mode,
+				       struct dentry *parent, u32 *value)
+{
+	if (!parent)
+		parent = edac_debugfs;
+
+	return debugfs_create_x32(name, mode, parent, value);
+}
+EXPORT_SYMBOL_GPL(edac_debugfs_create_x32);
diff --git a/drivers/edac/edac_module.h b/drivers/edac/edac_module.h
index dec88dcea036..546b16e29221 100644
--- a/drivers/edac/edac_module.h
+++ b/drivers/edac/edac_module.h
@@ -82,6 +82,8 @@ struct dentry *
 edac_debugfs_create_x8(const char *name, umode_t mode, struct dentry *parent, u8 *value);
 struct dentry *
 edac_debugfs_create_x16(const char *name, umode_t mode, struct dentry *parent, u16 *value);
+struct dentry *
+edac_debugfs_create_x32(const char *name, umode_t mode, struct dentry *parent, u32 *value);
 #else
 static inline int edac_debugfs_init(void)					{ return -ENODEV; }
 static inline void edac_debugfs_exit(void)					{ }
@@ -98,6 +100,9 @@ edac_debugfs_create_x8(const char *name, umode_t mode,
 static inline struct dentry *
 edac_debugfs_create_x16(const char *name, umode_t mode,
 		       struct dentry *parent, u16 *value)			{ return NULL; }
+static inline struct dentry *
+edac_debugfs_create_x32(const char *name, umode_t mode,
+		       struct dentry *parent, u32 *value)			{ return NULL; }
 #endif
 
 /*
-- 
2.19.1

[PATCH v6 8/9] EDAC: Add driver for the Marvell Armada XP SDRAM and L2 cache ECC

[Chris Packham]

From: Jan Luebbe <jlu@pengutronix.de>

Add support for the ECC functionality as found in the DDR RAM and L2
cache controllers on the MV78230/MV78x60 SoCs. This driver has been
tested on the MV78460 (on a custom board with a DDR3 ECC DIMM).

Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
[cp use SPDX license]
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
 MAINTAINERS                   |   6 +
 drivers/edac/Kconfig          |   7 +
 drivers/edac/Makefile         |   1 +
 drivers/edac/armada_xp_edac.c | 630 ++++++++++++++++++++++++++++++++++
 4 files changed, 644 insertions(+)
 create mode 100644 drivers/edac/armada_xp_edac.c

diff --git a/MAINTAINERS b/MAINTAINERS
index 6c7ed26e84fa..7ae4cfa5c121 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -5242,6 +5242,12 @@ L:	linux-edac@vger.kernel.org
 S:	Maintained
 F:	drivers/edac/amd64_edac*
 
+EDAC-ARMADA
+M:	Jan Luebbe <jlu@pengutronix.de>
+L:	linux-edac@vger.kernel.org
+S:	Maintained
+F:	drivers/edac/armada_xp_*
+
 EDAC-CALXEDA
 M:	Robert Richter <rric@kernel.org>
 L:	linux-edac@vger.kernel.org
diff --git a/drivers/edac/Kconfig b/drivers/edac/Kconfig
index 57304b2e989f..4567757d9f82 100644
--- a/drivers/edac/Kconfig
+++ b/drivers/edac/Kconfig
@@ -439,6 +439,13 @@ config EDAC_ALTERA_SDMMC
 	  Support for error detection and correction on the
 	  Altera SDMMC FIFO Memory for Altera SoCs.
 
+config EDAC_ARMADA_XP
+	bool "Marvell Armada XP DDR and L2 Cache ECC"
+	depends on MACH_MVEBU_V7
+	help
+	  Support for error correction and detection on the Marvell Aramada XP
+	  DDR RAM and L2 cache controllers.
+
 config EDAC_SYNOPSYS
 	tristate "Synopsys DDR Memory Controller"
 	depends on ARCH_ZYNQ
diff --git a/drivers/edac/Makefile b/drivers/edac/Makefile
index 02b43a7d8c3e..f3ea40b0ce9c 100644
--- a/drivers/edac/Makefile
+++ b/drivers/edac/Makefile
@@ -74,6 +74,7 @@ obj-$(CONFIG_EDAC_OCTEON_PCI)		+= octeon_edac-pci.o
 obj-$(CONFIG_EDAC_THUNDERX)		+= thunderx_edac.o
 
 obj-$(CONFIG_EDAC_ALTERA)		+= altera_edac.o
+obj-$(CONFIG_EDAC_ARMADA_XP)		+= armada_xp_edac.o
 obj-$(CONFIG_EDAC_SYNOPSYS)		+= synopsys_edac.o
 obj-$(CONFIG_EDAC_XGENE)		+= xgene_edac.o
 obj-$(CONFIG_EDAC_TI)			+= ti_edac.o
diff --git a/drivers/edac/armada_xp_edac.c b/drivers/edac/armada_xp_edac.c
new file mode 100644
index 000000000000..3759a4fbbdee
--- /dev/null
+++ b/drivers/edac/armada_xp_edac.c
@@ -0,0 +1,630 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 Pengutronix, Jan Luebbe <kernel@pengutronix.de>
+ */
+
+#include <linux/kernel.h>
+#include <linux/edac.h>
+#include <linux/of_platform.h>
+
+#include <asm/hardware/cache-l2x0.h>
+#include <asm/hardware/cache-aurora-l2.h>
+
+#include "edac_mc.h"
+#include "edac_device.h"
+#include "edac_module.h"
+
+/************************ EDAC MC (DDR RAM) ********************************/
+
+#define SDRAM_NUM_CS 4
+
+#define SDRAM_CONFIG_REG        0x0
+#define SDRAM_CONFIG_ECC_MASK         BIT(18)
+#define SDRAM_CONFIG_REGISTERED_MASK  BIT(17)
+#define SDRAM_CONFIG_BUS_WIDTH_MASK   BIT(15)
+
+#define SDRAM_ADDR_CTRL_REG     0x10
+#define SDRAM_ADDR_CTRL_SIZE_HIGH_OFFSET(cs) (20+cs)
+#define SDRAM_ADDR_CTRL_SIZE_HIGH_MASK(cs)   (0x1 << SDRAM_ADDR_CTRL_SIZE_HIGH_OFFSET(cs))
+#define SDRAM_ADDR_CTRL_ADDR_SEL_MASK(cs)    BIT(16+cs)
+#define SDRAM_ADDR_CTRL_SIZE_LOW_OFFSET(cs)  (cs*4+2)
+#define SDRAM_ADDR_CTRL_SIZE_LOW_MASK(cs)    (0x3 << SDRAM_ADDR_CTRL_SIZE_LOW_OFFSET(cs))
+#define SDRAM_ADDR_CTRL_STRUCT_OFFSET(cs)    (cs*4)
+#define SDRAM_ADDR_CTRL_STRUCT_MASK(cs)      (0x3 << SDRAM_ADDR_CTRL_STRUCT_OFFSET(cs))
+
+#define SDRAM_ERR_DATA_H_REG    0x40
+#define SDRAM_ERR_DATA_L_REG    0x44
+
+#define SDRAM_ERR_RECV_ECC_REG  0x48
+#define SDRAM_ERR_RECV_ECC_VALUE_MASK 0xff
+
+#define SDRAM_ERR_CALC_ECC_REG  0x4c
+#define SDRAM_ERR_CALC_ECC_ROW_OFFSET 8
+#define SDRAM_ERR_CALC_ECC_ROW_MASK   (0xffff << SDRAM_ERR_CALC_ECC_ROW_OFFSET)
+#define SDRAM_ERR_CALC_ECC_VALUE_MASK 0xff
+
+#define SDRAM_ERR_ADDR_REG      0x50
+#define SDRAM_ERR_ADDR_BANK_OFFSET    23
+#define SDRAM_ERR_ADDR_BANK_MASK      (0x7 << SDRAM_ERR_ADDR_BANK_OFFSET)
+#define SDRAM_ERR_ADDR_COL_OFFSET     8
+#define SDRAM_ERR_ADDR_COL_MASK       (0x7fff << SDRAM_ERR_ADDR_COL_OFFSET)
+#define SDRAM_ERR_ADDR_CS_OFFSET      1
+#define SDRAM_ERR_ADDR_CS_MASK        (0x3 << SDRAM_ERR_ADDR_CS_OFFSET)
+#define SDRAM_ERR_ADDR_TYPE_MASK      BIT(0)
+
+#define SDRAM_ERR_CTRL_REG      0x54
+#define SDRAM_ERR_CTRL_THR_OFFSET     16
+#define SDRAM_ERR_CTRL_THR_MASK       (0xff << SDRAM_ERR_CTRL_THR_OFFSET)
+#define SDRAM_ERR_CTRL_PROP_MASK      BIT(9)
+
+#define SDRAM_ERR_SBE_COUNT_REG 0x58
+#define SDRAM_ERR_DBE_COUNT_REG 0x5c
+
+#define SDRAM_ERR_CAUSE_ERR_REG 0xd0
+#define SDRAM_ERR_CAUSE_MSG_REG 0xd8
+#define SDRAM_ERR_CAUSE_DBE_MASK      BIT(1)
+#define SDRAM_ERR_CAUSE_SBE_MASK      BIT(0)
+
+#define SDRAM_RANK_CTRL_REG 0x1e0
+#define SDRAM_RANK_CTRL_EXIST_MASK(cs) BIT(cs)
+
+struct axp_mc_drvdata {
+	void __iomem *base;
+	/* width in bytes */
+	unsigned int width;
+	/* bank interleaving */
+	bool cs_addr_sel[SDRAM_NUM_CS];
+
+	char msg[128];
+};
+
+/* derived from "DRAM Address Multiplexing" in the ARAMDA XP Functional Spec */
+static uint32_t axp_mc_calc_address(struct axp_mc_drvdata *drvdata,
+				    uint8_t cs, uint8_t bank, uint16_t row,
+				    uint16_t col)
+{
+	if (drvdata->width == 8) {
+		/* 64 bit */
+		if (drvdata->cs_addr_sel[cs])
+			/* bank interleaved */
+			return (((row & 0xfff8) << 16) |
+				((bank & 0x7) << 16) |
+				((row & 0x7) << 13) |
+				((col & 0x3ff) << 3));
+		else
+			return (((row & 0xffff << 16) |
+				 ((bank & 0x7) << 13) |
+				 ((col & 0x3ff)) << 3));
+	} else if (drvdata->width == 4) {
+		/* 32 bit */
+		if (drvdata->cs_addr_sel[cs])
+			/* bank interleaved */
+			return (((row & 0xfff0) << 15) |
+				((bank & 0x7) << 16) |
+				((row & 0xf) << 12) |
+				((col & 0x3ff) << 2));
+		else
+			return (((row & 0xffff << 15) |
+				 ((bank & 0x7) << 12) |
+				 ((col & 0x3ff)) << 2));
+	} else {
+		/* 16 bit */
+		if (drvdata->cs_addr_sel[cs])
+			/* bank interleaved */
+			return (((row & 0xffe0) << 14) |
+				((bank & 0x7) << 16) |
+				((row & 0x1f) << 11) |
+				((col & 0x3ff) << 1));
+		else
+			return (((row & 0xffff << 14) |
+				 ((bank & 0x7) << 11) |
+				 ((col & 0x3ff)) << 1));
+	}
+}
+
+static void axp_mc_check(struct mem_ctl_info *mci)
+{
+	struct axp_mc_drvdata *drvdata = mci->pvt_info;
+	uint32_t data_h, data_l, recv_ecc, calc_ecc, addr;
+	uint32_t cnt_sbe, cnt_dbe, cause_err, cause_msg;
+	uint32_t row_val, col_val, bank_val, addr_val;
+	uint8_t syndrome_val, cs_val;
+	char *msg = drvdata->msg;
+
+	data_h    = readl(drvdata->base + SDRAM_ERR_DATA_H_REG);
+	data_l    = readl(drvdata->base + SDRAM_ERR_DATA_L_REG);
+	recv_ecc  = readl(drvdata->base + SDRAM_ERR_RECV_ECC_REG);
+	calc_ecc  = readl(drvdata->base + SDRAM_ERR_CALC_ECC_REG);
+	addr      = readl(drvdata->base + SDRAM_ERR_ADDR_REG);
+	cnt_sbe   = readl(drvdata->base + SDRAM_ERR_SBE_COUNT_REG);
+	cnt_dbe   = readl(drvdata->base + SDRAM_ERR_DBE_COUNT_REG);
+	cause_err = readl(drvdata->base + SDRAM_ERR_CAUSE_ERR_REG);
+	cause_msg = readl(drvdata->base + SDRAM_ERR_CAUSE_MSG_REG);
+
+	/* clear cause registers */
+	writel(~(SDRAM_ERR_CAUSE_DBE_MASK | SDRAM_ERR_CAUSE_SBE_MASK),
+	       drvdata->base + SDRAM_ERR_CAUSE_ERR_REG);
+	writel(~(SDRAM_ERR_CAUSE_DBE_MASK | SDRAM_ERR_CAUSE_SBE_MASK),
+	       drvdata->base + SDRAM_ERR_CAUSE_MSG_REG);
+
+	/* clear error counter registers */
+	if (cnt_sbe)
+		writel(0, drvdata->base + SDRAM_ERR_SBE_COUNT_REG);
+	if (cnt_dbe)
+		writel(0, drvdata->base + SDRAM_ERR_DBE_COUNT_REG);
+
+	if (!cnt_sbe && !cnt_dbe)
+		return;
+
+	if (!(addr & SDRAM_ERR_ADDR_TYPE_MASK)) {
+		if (cnt_sbe)
+			cnt_sbe--;
+		else
+			dev_warn(mci->pdev, "inconsistent SBE count detected");
+	} else {
+		if (cnt_dbe)
+			cnt_dbe--;
+		else
+			dev_warn(mci->pdev, "inconsistent DBE count detected");
+	}
+
+	/* report earlier errors */
+	if (cnt_sbe)
+		edac_mc_handle_error(HW_EVENT_ERR_CORRECTED, mci,
+				     cnt_sbe, /* error count */
+				     0, 0, 0, /* pfn, offset, syndrome */
+				     -1, -1, -1, /* top, mid, low layer */
+				     mci->ctl_name,
+				     "details unavailable (multiple errors)");
+	if (cnt_dbe)
+		edac_mc_handle_error(HW_EVENT_ERR_UNCORRECTED, mci,
+				     cnt_sbe, /* error count */
+				     0, 0, 0, /* pfn, offset, syndrome */
+				     -1, -1, -1, /* top, mid, low layer */
+				     mci->ctl_name,
+				     "details unavailable (multiple errors)");
+
+	/* report details for most recent error */
+	cs_val   = (addr & SDRAM_ERR_ADDR_CS_MASK) >> SDRAM_ERR_ADDR_CS_OFFSET;
+	bank_val = (addr & SDRAM_ERR_ADDR_BANK_MASK) >> SDRAM_ERR_ADDR_BANK_OFFSET;
+	row_val  = (calc_ecc & SDRAM_ERR_CALC_ECC_ROW_MASK) >> SDRAM_ERR_CALC_ECC_ROW_OFFSET;
+	col_val  = (addr & SDRAM_ERR_ADDR_COL_MASK) >> SDRAM_ERR_ADDR_COL_OFFSET;
+	syndrome_val = (recv_ecc ^ calc_ecc) & 0xff;
+	addr_val = axp_mc_calc_address(drvdata, cs_val, bank_val, row_val,
+				       col_val);
+	msg += sprintf(msg, "row=0x%04x ", row_val); /* 11 chars */
+	msg += sprintf(msg, "bank=0x%x ", bank_val); /*  9 chars */
+	msg += sprintf(msg, "col=0x%04x ", col_val); /* 11 chars */
+	msg += sprintf(msg, "cs=%d", cs_val);	     /*  4 chars */
+
+	if (!(addr & SDRAM_ERR_ADDR_TYPE_MASK)) {
+		edac_mc_handle_error(HW_EVENT_ERR_CORRECTED, mci,
+				     1,	/* error count */
+				     addr_val >> PAGE_SHIFT,
+				     addr_val & ~PAGE_MASK,
+				     syndrome_val,
+				     cs_val, -1, -1, /* top, mid, low layer */
+				     mci->ctl_name, drvdata->msg);
+	} else {
+		edac_mc_handle_error(HW_EVENT_ERR_UNCORRECTED, mci,
+				     1,	/* error count */
+				     addr_val >> PAGE_SHIFT,
+				     addr_val & ~PAGE_MASK,
+				     syndrome_val,
+				     cs_val, -1, -1, /* top, mid, low layer */
+				     mci->ctl_name, drvdata->msg);
+	}
+}
+
+static void axp_mc_read_config(struct mem_ctl_info *mci)
+{
+	struct axp_mc_drvdata *drvdata = mci->pvt_info;
+	uint32_t config, addr_ctrl, rank_ctrl;
+	unsigned int i, cs_struct, cs_size;
+	struct dimm_info *dimm;
+
+	config = readl(drvdata->base + SDRAM_CONFIG_REG);
+	if (config & SDRAM_CONFIG_BUS_WIDTH_MASK)
+		/* 64 bit */
+		drvdata->width = 8;
+	else
+		/* 32 bit */
+		drvdata->width = 4;
+
+	addr_ctrl = readl(drvdata->base + SDRAM_ADDR_CTRL_REG);
+	rank_ctrl = readl(drvdata->base + SDRAM_RANK_CTRL_REG);
+	for (i = 0; i < SDRAM_NUM_CS; i++) {
+		dimm = mci->dimms[i];
+
+		if (!(rank_ctrl & SDRAM_RANK_CTRL_EXIST_MASK(i)))
+			continue;
+
+		drvdata->cs_addr_sel[i] =
+			!!(addr_ctrl & SDRAM_ADDR_CTRL_ADDR_SEL_MASK(i));
+
+		cs_struct = (addr_ctrl & SDRAM_ADDR_CTRL_STRUCT_MASK(i)) >> SDRAM_ADDR_CTRL_STRUCT_OFFSET(i);
+		cs_size   = ((addr_ctrl & SDRAM_ADDR_CTRL_SIZE_HIGH_MASK(i)) >> (SDRAM_ADDR_CTRL_SIZE_HIGH_OFFSET(i) - 2) |
+			    ((addr_ctrl & SDRAM_ADDR_CTRL_SIZE_LOW_MASK(i)) >> SDRAM_ADDR_CTRL_SIZE_LOW_OFFSET(i)));
+
+		switch (cs_size) {
+		case 0: /* 2GBit */
+			dimm->nr_pages = 524288;
+			break;
+		case 1: /* 256MBit */
+			dimm->nr_pages = 65536;
+			break;
+		case 2: /* 512MBit */
+			dimm->nr_pages = 131072;
+			break;
+		case 3: /* 1GBit */
+			dimm->nr_pages = 262144;
+			break;
+		case 4: /* 4GBit */
+			dimm->nr_pages = 1048576;
+			break;
+		case 5: /* 8GBit */
+			dimm->nr_pages = 2097152;
+			break;
+		}
+		dimm->grain = 8;
+		dimm->dtype = cs_struct ? DEV_X16 : DEV_X8;
+		dimm->mtype = (config & SDRAM_CONFIG_REGISTERED_MASK) ?
+			MEM_RDDR3 : MEM_DDR3;
+		dimm->edac_mode = EDAC_SECDED;
+	}
+}
+
+static const struct of_device_id axp_mc_of_match[] = {
+	{.compatible = "marvell,armada-xp-sdram-controller",},
+	{},
+};
+MODULE_DEVICE_TABLE(of, axp_mc_of_match);
+
+static int axp_mc_probe(struct platform_device *pdev)
+{
+	struct axp_mc_drvdata *drvdata;
+	struct edac_mc_layer layers[1];
+	const struct of_device_id *id;
+	struct mem_ctl_info *mci;
+	struct resource *r;
+	void __iomem *base;
+	uint32_t config;
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!r) {
+		dev_err(&pdev->dev, "Unable to get mem resource\n");
+		return -ENODEV;
+	}
+
+	base = devm_ioremap_resource(&pdev->dev, r);
+	if (IS_ERR(base)) {
+		dev_err(&pdev->dev, "Unable to map regs\n");
+		return PTR_ERR(base);
+	}
+
+	config = readl(base + SDRAM_CONFIG_REG);
+	if (!(config & SDRAM_CONFIG_ECC_MASK)) {
+		dev_warn(&pdev->dev, "SDRAM ECC is not enabled");
+		return -EINVAL;
+	}
+
+	layers[0].type = EDAC_MC_LAYER_CHIP_SELECT;
+	layers[0].size = SDRAM_NUM_CS;
+	layers[0].is_virt_csrow = true;
+
+	mci = edac_mc_alloc(0, ARRAY_SIZE(layers), layers, sizeof(*drvdata));
+	if (!mci)
+		return -ENOMEM;
+
+	drvdata = mci->pvt_info;
+	drvdata->base = base;
+	mci->pdev = &pdev->dev;
+	platform_set_drvdata(pdev, mci);
+
+	id = of_match_device(axp_mc_of_match, &pdev->dev);
+	mci->edac_check = axp_mc_check;
+	mci->mtype_cap = MEM_FLAG_DDR3;
+	mci->edac_cap = EDAC_FLAG_SECDED;
+	mci->mod_name = pdev->dev.driver->name;
+	mci->ctl_name = id ? id->compatible : "unknown";
+	mci->dev_name = dev_name(&pdev->dev);
+	mci->scrub_mode = SCRUB_NONE;
+
+	axp_mc_read_config(mci);
+
+	/* configure SBE threshold */
+	/* it seems that SBEs are not captured otherwise */
+	writel(1 << SDRAM_ERR_CTRL_THR_OFFSET, drvdata->base + SDRAM_ERR_CTRL_REG);
+
+	/* clear cause registers */
+	writel(~(SDRAM_ERR_CAUSE_DBE_MASK | SDRAM_ERR_CAUSE_SBE_MASK), drvdata->base + SDRAM_ERR_CAUSE_ERR_REG);
+	writel(~(SDRAM_ERR_CAUSE_DBE_MASK | SDRAM_ERR_CAUSE_SBE_MASK), drvdata->base + SDRAM_ERR_CAUSE_MSG_REG);
+
+	/* clear counter registers */
+	writel(0, drvdata->base + SDRAM_ERR_SBE_COUNT_REG);
+	writel(0, drvdata->base + SDRAM_ERR_DBE_COUNT_REG);
+
+	if (edac_mc_add_mc(mci)) {
+		edac_mc_free(mci);
+		return -EINVAL;
+	}
+	edac_op_state = EDAC_OPSTATE_POLL;
+
+	return 0;
+}
+
+static int axp_mc_remove(struct platform_device *pdev)
+{
+	struct mem_ctl_info *mci = platform_get_drvdata(pdev);
+
+	edac_mc_del_mc(&pdev->dev);
+	edac_mc_free(mci);
+	platform_set_drvdata(pdev, NULL);
+
+	return 0;
+}
+
+static struct platform_driver axp_mc_driver = {
+	.probe = axp_mc_probe,
+	.remove = axp_mc_remove,
+	.driver = {
+		.name = "armada_xp_mc_edac",
+		.of_match_table = of_match_ptr(axp_mc_of_match),
+	},
+};
+
+/************************ EDAC Device (L2 Cache) ***************************/
+
+struct aurora_l2_drvdata {
+	void __iomem *base;
+
+	char msg[128];
+
+	/* error injection via debugfs */
+	uint32_t inject_addr;
+	uint32_t inject_mask;
+	uint8_t inject_ctl;
+
+	struct dentry *debugfs;
+};
+
+#ifdef CONFIG_EDAC_DEBUG
+static void aurora_l2_inject(struct aurora_l2_drvdata *drvdata)
+{
+	drvdata->inject_addr &= AURORA_ERR_INJECT_CTL_ADDR_MASK;
+	drvdata->inject_ctl &= AURORA_ERR_INJECT_CTL_EN_MASK;
+	writel(0, drvdata->base + AURORA_ERR_INJECT_CTL_REG);
+	writel(drvdata->inject_mask, drvdata->base + AURORA_ERR_INJECT_MASK_REG);
+	writel(drvdata->inject_addr | drvdata->inject_ctl, drvdata->base + AURORA_ERR_INJECT_CTL_REG);
+}
+#endif
+
+static void aurora_l2_check(struct edac_device_ctl_info *dci)
+{
+	struct aurora_l2_drvdata *drvdata = dci->pvt_info;
+	uint32_t cnt, src, txn, err, attr_cap, addr_cap, way_cap;
+	unsigned int cnt_ce, cnt_ue;
+	char *msg = drvdata->msg;
+	size_t size = sizeof(drvdata->msg);
+	size_t len = 0;
+
+	cnt = readl(drvdata->base + AURORA_ERR_CNT_REG);
+	attr_cap = readl(drvdata->base + AURORA_ERR_ATTR_CAP_REG);
+	addr_cap = readl(drvdata->base + AURORA_ERR_ADDR_CAP_REG);
+	way_cap = readl(drvdata->base + AURORA_ERR_WAY_CAP_REG);
+
+	cnt_ce = (cnt & AURORA_ERR_CNT_CE_MASK) >> AURORA_ERR_CNT_CE_OFFSET;
+	cnt_ue = (cnt & AURORA_ERR_CNT_UE_MASK) >> AURORA_ERR_CNT_UE_OFFSET;
+	/* clear error counter registers */
+	if (cnt_ce || cnt_ue)
+		writel(AURORA_ERR_CNT_CLR, drvdata->base + AURORA_ERR_CNT_REG);
+
+	if (!(attr_cap & AURORA_ERR_ATTR_CAP_VALID))
+		goto clear_remaining;
+
+	src = (attr_cap & AURORA_ERR_ATTR_SRC_MSK) >> AURORA_ERR_ATTR_SRC_OFF;
+	if (src <= 3)
+		len += snprintf(msg+len, size-len, "src=CPU%d ", src);
+	else
+		len += snprintf(msg+len, size-len, "src=IO ");
+
+	txn =  (attr_cap & AURORA_ERR_ATTR_TXN_MSK) >> AURORA_ERR_ATTR_TXN_OFF;
+	switch (txn) {
+	case 0:
+		len += snprintf(msg+len, size-len, "txn=Data-Read ");
+		break;
+	case 1:
+		len += snprintf(msg+len, size-len, "txn=Isn-Read ");
+		break;
+	case 2:
+		len += snprintf(msg+len, size-len, "txn=Clean-Flush ");
+		break;
+	case 3:
+		len += snprintf(msg+len, size-len, "txn=Eviction ");
+		break;
+	case 4:
+		len += snprintf(msg+len, size-len,
+				"txn=Read-Modify-Write ");
+		break;
+	}
+
+	err = (attr_cap & AURORA_ERR_ATTR_ERR_MSK) >> AURORA_ERR_ATTR_ERR_OFF;
+	switch (err) {
+	case 0:
+		len += snprintf(msg+len, size-len, "err=CorrECC ");
+		break;
+	case 1:
+		len += snprintf(msg+len, size-len, "err=UnCorrECC ");
+		break;
+	case 2:
+		len += snprintf(msg+len, size-len, "err=TagParity ");
+		break;
+	}
+
+	len += snprintf(msg+len, size-len, "addr=0x%x ", addr_cap & AURORA_ERR_ADDR_CAP_ADDR_MASK);
+	len += snprintf(msg+len, size-len, "index=0x%x ", (way_cap & AURORA_ERR_WAY_IDX_MSK) >> AURORA_ERR_WAY_IDX_OFF);
+	len += snprintf(msg+len, size-len, "way=0x%x", (way_cap & AURORA_ERR_WAY_CAP_WAY_MASK) >> AURORA_ERR_WAY_CAP_WAY_OFFSET);
+
+	/* clear error capture registers */
+	writel(AURORA_ERR_ATTR_CAP_VALID, drvdata->base + AURORA_ERR_ATTR_CAP_REG);
+	if (err) {
+		/* UnCorrECC or TagParity */
+		if (cnt_ue)
+			cnt_ue--;
+		edac_device_handle_ue(dci, 0, 0, drvdata->msg);
+	} else {
+		if (cnt_ce)
+			cnt_ce--;
+		edac_device_handle_ce(dci, 0, 0, drvdata->msg);
+	}
+
+clear_remaining:
+	/* report remaining errors */
+	while (cnt_ue--)
+		edac_device_handle_ue(dci, 0, 0, "details unavailable (multiple errors)");
+	while (cnt_ce--)
+		edac_device_handle_ue(dci, 0, 0, "details unavailable (multiple errors)");
+}
+
+static void aurora_l2_poll(struct edac_device_ctl_info *dci)
+{
+#ifdef CONFIG_EDAC_DEBUG
+	struct aurora_l2_drvdata *drvdata = dci->pvt_info;
+#endif
+
+	aurora_l2_check(dci);
+#ifdef CONFIG_EDAC_DEBUG
+	aurora_l2_inject(drvdata);
+#endif
+}
+
+static const struct of_device_id aurora_l2_of_match[] = {
+	{.compatible = "marvell,aurora-system-cache",},
+	{},
+};
+MODULE_DEVICE_TABLE(of, aurora_l2_of_match);
+
+static int aurora_l2_probe(struct platform_device *pdev)
+{
+	struct aurora_l2_drvdata *drvdata;
+	struct edac_device_ctl_info *dci;
+	const struct of_device_id *id;
+	uint32_t l2x0_aux_ctrl;
+	void __iomem *base;
+	struct resource *r;
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!r) {
+		dev_err(&pdev->dev, "Unable to get mem resource\n");
+		return -ENODEV;
+	}
+
+	base = devm_ioremap_resource(&pdev->dev, r);
+	if (IS_ERR(base)) {
+		dev_err(&pdev->dev, "Unable to map regs\n");
+		return PTR_ERR(base);
+	}
+
+	l2x0_aux_ctrl = readl(base + L2X0_AUX_CTRL);
+	if (!(l2x0_aux_ctrl & AURORA_ACR_PARITY_EN))
+		dev_warn(&pdev->dev, "tag parity is not enabled");
+	if (!(l2x0_aux_ctrl & AURORA_ACR_ECC_EN))
+		dev_warn(&pdev->dev, "data ECC is not enabled");
+
+	dci = edac_device_alloc_ctl_info(sizeof(*drvdata),
+					 "cpu", 1, "L", 1, 2, NULL, 0, 0);
+	if (!dci)
+		return -ENOMEM;
+
+	drvdata = dci->pvt_info;
+	drvdata->base = base;
+	dci->dev = &pdev->dev;
+	platform_set_drvdata(pdev, dci);
+
+	id = of_match_device(aurora_l2_of_match, &pdev->dev);
+	dci->edac_check = aurora_l2_poll;
+	dci->mod_name = pdev->dev.driver->name;
+	dci->ctl_name = id ? id->compatible : "unknown";
+	dci->dev_name = dev_name(&pdev->dev);
+
+	/* clear registers */
+	writel(AURORA_ERR_CNT_CLR, drvdata->base + AURORA_ERR_CNT_REG);
+	writel(AURORA_ERR_ATTR_CAP_VALID, drvdata->base + AURORA_ERR_ATTR_CAP_REG);
+
+	if (edac_device_add_device(dci)) {
+		edac_device_free_ctl_info(dci);
+		return -EINVAL;
+	}
+
+#ifdef CONFIG_EDAC_DEBUG
+	drvdata->debugfs = edac_debugfs_create_dir(dev_name(&pdev->dev));
+	if (drvdata->debugfs) {
+		edac_debugfs_create_x32("inject_addr", 0644,
+					drvdata->debugfs,
+					&drvdata->inject_addr);
+		edac_debugfs_create_x32("inject_mask", 0644,
+					drvdata->debugfs,
+					&drvdata->inject_mask);
+		edac_debugfs_create_x8("inject_ctl", 0644,
+				       drvdata->debugfs, &drvdata->inject_ctl);
+	}
+#endif
+
+	return 0;
+}
+
+static int aurora_l2_remove(struct platform_device *pdev)
+{
+	struct edac_device_ctl_info *dci = platform_get_drvdata(pdev);
+#ifdef CONFIG_EDAC_DEBUG
+	struct aurora_l2_drvdata *drvdata = dci->pvt_info;
+
+	edac_debugfs_remove_recursive(drvdata->debugfs);
+#endif
+	edac_device_del_device(&pdev->dev);
+	edac_device_free_ctl_info(dci);
+	platform_set_drvdata(pdev, NULL);
+
+	return 0;
+}
+
+static struct platform_driver aurora_l2_driver = {
+	.probe = aurora_l2_probe,
+	.remove = aurora_l2_remove,
+	.driver = {
+		.name = "aurora_l2_edac",
+		.of_match_table = of_match_ptr(aurora_l2_of_match),
+	},
+};
+
+/************************ Driver registration ******************************/
+
+static struct platform_driver * const drivers[] = {
+	&axp_mc_driver,
+	&aurora_l2_driver,
+};
+
+static int __init armada_xp_edac_init(void)
+{
+	int res;
+
+	/* only polling is supported */
+	edac_op_state = EDAC_OPSTATE_POLL;
+
+	res = platform_register_drivers(drivers, ARRAY_SIZE(drivers));
+	if (res)
+		pr_warn("Aramda XP EDAC drivers fail to register\n");
+
+	return 0;
+}
+module_init(armada_xp_edac_init);
+
+static void __exit armada_xp_edac_exit(void)
+{
+	platform_unregister_drivers(drivers, ARRAY_SIZE(drivers));
+}
+module_exit(armada_xp_edac_exit);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Pengutronix");
+MODULE_DESCRIPTION("EDAC Drivers for Marvell Armada XP SDRAM and L2 Cache Controller");
-- 
2.19.1

[PATCH v6 9/9] EDAC: armada_xp: Add support for more SoCs

[Chris Packham]

The Armada 38x and other integrated SoCs use a reduced pin count so the
width of the SDRAM interface is smaller than the Armada XP SoCs. This
means that the definition of "full" and "half" width is reduced from
64/32 to 32/16.

Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
 drivers/edac/armada_xp_edac.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/edac/armada_xp_edac.c b/drivers/edac/armada_xp_edac.c
index 3759a4fbbdee..7f227bdcbc84 100644
--- a/drivers/edac/armada_xp_edac.c
+++ b/drivers/edac/armada_xp_edac.c
@@ -332,6 +332,11 @@ static int axp_mc_probe(struct platform_device *pdev)
 
 	axp_mc_read_config(mci);
 
+	/* These SoCs have a reduced width bus */
+	if (of_machine_is_compatible("marvell,armada380") ||
+	    of_machine_is_compatible("marvell,armadaxp-98dx3236"))
+		drvdata->width /= 2;
+
 	/* configure SBE threshold */
 	/* it seems that SBEs are not captured otherwise */
 	writel(1 << SDRAM_ERR_CTRL_THR_OFFSET, drvdata->base + SDRAM_ERR_CTRL_REG);
-- 
2.19.1

Re: [PATCH v6 5/9] dt-bindings: ARM: document marvell,ecc-enable binding

[Arnd Bergmann]

On Fri, Nov 9, 2018 at 8:04 AM Chris Packham
<chris.packham@alliedtelesis.co.nz> wrote:
>
> Add documentation for the marvell,ecc-enable and marvell,ecc-disable
> properties which can be used to enable/disable ECC on the Marvell aurora
> cache.
>
> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
> ---

Why do you need both enable and disable? Wouldn't one of them be enough here?

      Arnd

Re: [PATCH v6 5/9] dt-bindings: ARM: document marvell,ecc-enable binding

[Russell King - ARM Linux]

On Fri, Nov 09, 2018 at 12:40:06PM +0100, Arnd Bergmann wrote:
> On Fri, Nov 9, 2018 at 8:04 AM Chris Packham
> <chris.packham@alliedtelesis.co.nz> wrote:
> >
> > Add documentation for the marvell,ecc-enable and marvell,ecc-disable
> > properties which can be used to enable/disable ECC on the Marvell aurora
> > cache.
> >
> > Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
> > ---
> 
> Why do you need both enable and disable? Wouldn't one of them be enough here?

It isn't an "on when ecc-enable is present, off when not" because the
current behaviour is to preserve these bits in the control register.

If we were to implement it as "if no ecc-enable property, turn off
ECC" then that would drastically change the behaviour - systems which
were configured for ECC suddenly lose ECC support.

Since we don't know which have it and which don't, we can't implement
the option like that.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up

Re: [PATCH v6 5/9] dt-bindings: ARM: document marvell,ecc-enable binding

[Arnd Bergmann]

On Fri, Nov 9, 2018 at 12:48 PM Russell King - ARM Linux
<linux@armlinux.org.uk> wrote:
>
> On Fri, Nov 09, 2018 at 12:40:06PM +0100, Arnd Bergmann wrote:
> > On Fri, Nov 9, 2018 at 8:04 AM Chris Packham
> > <chris.packham@alliedtelesis.co.nz> wrote:
> > >
> > > Add documentation for the marvell,ecc-enable and marvell,ecc-disable
> > > properties which can be used to enable/disable ECC on the Marvell aurora
> > > cache.
> > >
> > > Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
> > > ---
> >
> > Why do you need both enable and disable? Wouldn't one of them be enough here?
>
> It isn't an "on when ecc-enable is present, off when not" because the
> current behaviour is to preserve these bits in the control register.
>
> If we were to implement it as "if no ecc-enable property, turn off
> ECC" then that would drastically change the behaviour - systems which
> were configured for ECC suddenly lose ECC support.
>
> Since we don't know which have it and which don't, we can't implement
> the option like that.

What I meant was why we need support force-disabling it. I understand
that we need to allow leaving it at the boot-time default as well as
force-enabling it.

       Arnd

Re: [PATCH v6 8/9] EDAC: Add driver for the Marvell Armada XP SDRAM and L2 cache ECC

[Borislav Petkov]

On Fri, Nov 09, 2018 at 08:03:48PM +1300, Chris Packham wrote:
> From: Jan Luebbe <jlu@pengutronix.de>
> 
> Add support for the ECC functionality as found in the DDR RAM and L2
> cache controllers on the MV78230/MV78x60 SoCs. This driver has been
> tested on the MV78460 (on a custom board with a DDR3 ECC DIMM).
> 
> Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
> [cp use SPDX license]
> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
> ---
>  MAINTAINERS                   |   6 +
>  drivers/edac/Kconfig          |   7 +
>  drivers/edac/Makefile         |   1 +
>  drivers/edac/armada_xp_edac.c | 630 ++++++++++++++++++++++++++++++++++
>  4 files changed, 644 insertions(+)
>  create mode 100644 drivers/edac/armada_xp_edac.c

Looks ok at a glance. Those overly long lines could use some macros or
breaking but it is not a big deal:

Reviewed-by: Borislav Petkov <bp@suse.de>

-- 
Regards/Gruss,
    Boris.

Good mailing practices for 400: avoid top-posting and trim the reply.

Re: [PATCH v6 5/9] dt-bindings: ARM: document marvell,ecc-enable binding

[Chris Packham]

On 10/11/18 4:58 AM, Arnd Bergmann wrote:
> On Fri, Nov 9, 2018 at 12:48 PM Russell King - ARM Linux
> <linux@armlinux.org.uk> wrote:
>>
>> On Fri, Nov 09, 2018 at 12:40:06PM +0100, Arnd Bergmann wrote:
>>> On Fri, Nov 9, 2018 at 8:04 AM Chris Packham
>>> <chris.packham@alliedtelesis.co.nz> wrote:
>>>>
>>>> Add documentation for the marvell,ecc-enable and marvell,ecc-disable
>>>> properties which can be used to enable/disable ECC on the Marvell aurora
>>>> cache.
>>>>
>>>> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
>>>> ---
>>>
>>> Why do you need both enable and disable? Wouldn't one of them be enough here?
>>
>> It isn't an "on when ecc-enable is present, off when not" because the
>> current behaviour is to preserve these bits in the control register.
>>
>> If we were to implement it as "if no ecc-enable property, turn off
>> ECC" then that would drastically change the behaviour - systems which
>> were configured for ECC suddenly lose ECC support.
>>
>> Since we don't know which have it and which don't, we can't implement
>> the option like that.
> 
> What I meant was why we need support force-disabling it. I understand
> that we need to allow leaving it at the boot-time default as well as
> force-enabling it.

I added ecc-disable because I was modeling it after 
arm,parity-enable/arm,parity-disable. The only reason I can imagine 
wanting to force disable this would be some mis-behaving SoC which has 
it enabled by default in hardware, to my knowledge no such system exists 
(that would use this driver).

I'd be happy to drop the binding an implementation and send a v7 if you 
feel strongly that it marvell,ecc-disable should be removed.

Re: [PATCH v6 5/9] dt-bindings: ARM: document marvell,ecc-enable binding

[Rob Herring]

On Fri,  9 Nov 2018 20:03:45 +1300, Chris Packham wrote:
> Add documentation for the marvell,ecc-enable and marvell,ecc-disable
> properties which can be used to enable/disable ECC on the Marvell aurora
> cache.
> 
> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
> ---
> 
> Notes:
>     Changes in v6:
>     - new (split binding doc from implementation).
> 
>  Documentation/devicetree/bindings/arm/l2c2x0.txt | 2 ++
>  1 file changed, 2 insertions(+)
> 

Reviewed-by: Rob Herring <robh@kernel.org>