linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Jerome Brunet <jbrunet@baylibre.com>
To: Kevin Hilman <khilman@baylibre.com>,
	Carlo Caione <carlo@caione.org>,
	Neil Armstrong <narmstrong@baylibre.com>
Cc: linux-amlogic@lists.infradead.org, linux-kernel@vger.kernel.org,
	devicetree@vger.kernel.org, Jerome Brunet <jbrunet@baylibre.com>
Subject: [PATCH 2/2] arm64: dts: meson: add libretech aml-s805x-ac board
Date: Wed, 14 Nov 2018 11:19:25 +0100	[thread overview]
Message-ID: <20181114101925.10526-3-jbrunet@baylibre.com> (raw)
In-Reply-To: <20181114101925.10526-1-jbrunet@baylibre.com>

From: Neil Armstrong <narmstrong@baylibre.com>

Add Libretech aml-s805x-ac board (aka 'La Frite') support

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
 arch/arm64/boot/dts/amlogic/Makefile          |   1 +
 .../amlogic/meson-gxl-s805x-libretech-ac.dts  | 249 ++++++++++++++++++
 2 files changed, 250 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s805x-libretech-ac.dts

diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index c31f29d660de..bc41629c5df4 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -11,6 +11,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-vega-s95-meta.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-vega-s95-telos.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-wetek-hub.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-wetek-play2.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-libretech-ac.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-hwacom-amazetv.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-khadas-vim.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-libretech-cc.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s805x-libretech-ac.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s805x-libretech-ac.dts
new file mode 100644
index 000000000000..fbc100e4445a
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s805x-libretech-ac.dts
@@ -0,0 +1,249 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2018 BayLibre, SAS.
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ * Author: Jerome Brunet <jbrunet@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+
+#include "meson-gxl-s905x.dtsi"
+
+/ {
+	compatible = "libretech,aml-s805x-ac", "amlogic,s805x",
+		     "amlogic,meson-gxl";
+	model = "Libre Computer Board AML-S805X-AC";
+
+	aliases {
+		serial0 = &uart_AO;
+		ethernet0 = &ethmac;
+		spi0 = &spifc;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	cvbs-connector {
+		/*
+		 * The pads are present but no connector is soldered on
+		 * 2J2, so keep this off by default.
+		 */
+		status = "disabled";
+		compatible = "composite-video-connector";
+
+		port {
+			cvbs_connector_in: endpoint {
+				remote-endpoint = <&cvbs_vdac_out>;
+			};
+		};
+	};
+
+	dc_5v: regulator-dc_5v {
+		compatible = "regulator-fixed";
+		regulator-name = "DC_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x20000000>;
+	};
+
+	vcck: regulator-vcck {
+		compatible = "regulator-fixed";
+		regulator-name = "VCCK";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&dc_5v>;
+
+		/*
+		 * This is controlled by GPIOAO_9 we reserve this but
+		 * claiming it as done bellow reset the board anyway
+		 * Need to investigate this
+		 *
+		 * gpio = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
+		 * enable-active-high;
+		 */
+		regulator-always-on;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&dc_5v>;
+		regulator-always-on;
+	};
+
+	vddio_boot: regulator-vddio_boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-always-on;
+	};
+};
+
+&cec_AO {
+	status = "okay";
+	pinctrl-0 = <&ao_cec_pins>;
+	pinctrl-names = "default";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cvbs_vdac_port {
+	cvbs_vdac_out: endpoint {
+		remote-endpoint = <&cvbs_connector_in>;
+	};
+};
+
+&ethmac {
+	status = "okay";
+};
+
+&internal_phy {
+	pinctrl-0 = <&eth_link_led_pins>, <&eth_act_led_pins>;
+	pinctrl-names = "default";
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
+	pinctrl-names = "default";
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&pinctrl_aobus {
+	gpio-line-names = "UART TX",
+			  "UART RX",
+			  "7J1 Header Pin31",
+			  "", "", "", "",
+			  "IR In",
+			  "HDMI CEC",
+			  "5V VCCK Regulator",
+			  /* GPIO_TEST_N */
+			  "";
+};
+
+&pinctrl_periphs {
+	gpio-line-names = /* Bank GPIOZ */
+			  "", "", "", "", "", "", "",
+			  "", "", "", "", "", "", "",
+			  "Eth Link LED", "Eth Activity LED",
+			  /* Bank GPIOH */
+			  "HDMI HPD", "HDMI SDA", "HDMI SCL",
+			  "", "7J1 Header Pin13",
+			  "7J1 Header Pin15",
+			  "7J1 Header Pin7",
+			  "7J1 Header Pin12",
+			  "7J1 Header Pin16",
+			  "7J1 Header Pin18",
+			  /* Bank BOOT */
+			  "eMMC D0", "eMMC D1", "eMMC D2", "eMMC D3",
+			  "eMMC D4", "eMMC D5", "eMMC D6", "eMMC D7",
+			  "eMMC Clk", "eMMC Reset", "eMMC CMD",
+			  "SPI NOR MOSI", "SPI NOR MISO", "SPI NOR Clk",
+			  "", "SPI NOR Chip Select",
+			  /* Bank CARD */
+			  "", "", "", "", "", "", "",
+			  /* Bank GPIODV */
+			  "", "", "", "", "", "", "", "", "", "", "", "",
+			  "", "", "", "", "", "", "", "", "", "", "", "",
+			  "7J1 Header Pin27", "7J1 Header Pin28", "",
+			  "7J1 Header Pin29",
+			  "VCCK Regulator", "VDDEE Regulator",
+			  /* Bank GPIOX */
+			  "7J1 Header Pin22", "7J1 Header Pin26",
+			  "7J1 Header Pin36", "7J1 Header Pin38",
+			  "7J1 Header Pin40", "7J1 Header Pin37",
+			  "7J1 Header Pin33", "7J1 Header Pin35",
+			  "7J1 Header Pin19", "7J1 Header Pin21",
+			  "7J1 Header Pin24", "7J1 Header Pin23",
+			  "7J1 Header Pin8", "7J1 Header Pin10",
+			  "", "", "7J1 Header Pin32", "", "",
+			  /* Bank GPIOCLK */
+			  "", "";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddio_boot>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	max-frequency = <200000000>;
+	disable-wp;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+&spifc {
+	status = "okay";
+	pinctrl-0 = <&nor_pins>;
+	pinctrl-names = "default";
+
+	w25q32: spi-flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <3000000>;
+	};
+};
+
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb0 {
+	status = "okay";
+};
-- 
2.19.1


  parent reply	other threads:[~2018-11-14 10:19 UTC|newest]

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-11-14 10:19 [PATCH 0/2] arm64: dts: meson: add Libretech aml-s805x-ac support Jerome Brunet
2018-11-14 10:19 ` [PATCH 1/2] dt-bindings: arm: amlogic: add libretech aml-s805x-ac bindings Jerome Brunet
2018-11-14 10:19 ` Jerome Brunet [this message]
2018-11-14 10:38   ` [PATCH RESEND 2/2] arm64: dts: meson: add libretech aml-s805x-ac board Jerome Brunet
2018-11-14 14:37     ` Peter Korsgaard
2018-11-15  9:13       ` Neil Armstrong

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20181114101925.10526-3-jbrunet@baylibre.com \
    --to=jbrunet@baylibre.com \
    --cc=carlo@caione.org \
    --cc=devicetree@vger.kernel.org \
    --cc=khilman@baylibre.com \
    --cc=linux-amlogic@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=narmstrong@baylibre.com \
    --subject='Re: [PATCH 2/2] arm64: dts: meson: add libretech aml-s805x-ac board' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
on how to clone and mirror all data and code used for this inbox