linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
* [PATCH] dt-bindings: media: i2c: Fix external clock frequency for OV5645
@ 2018-11-14 10:39 Manivannan Sadhasivam
  2018-11-14 10:57 ` Sakari Ailus
  0 siblings, 1 reply; 3+ messages in thread
From: Manivannan Sadhasivam @ 2018-11-14 10:39 UTC (permalink / raw)
  To: mchehab, robh+dt, todor.tomov, hansverk
  Cc: linux-media, devicetree, linux-kernel, Manivannan Sadhasivam

Commit "4adb0a0432f4 media: ov5645: Supported external clock is 24MHz"
modified the external clock frequency to be 24MHz instead of the
23.88MHz in driver. Hence, make the same change in corresponding bindings
doc and mention the acceptable tolerance.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 Documentation/devicetree/bindings/media/i2c/ov5645.txt | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/media/i2c/ov5645.txt b/Documentation/devicetree/bindings/media/i2c/ov5645.txt
index fd7aec9f8e24..b155583469a4 100644
--- a/Documentation/devicetree/bindings/media/i2c/ov5645.txt
+++ b/Documentation/devicetree/bindings/media/i2c/ov5645.txt
@@ -8,7 +8,8 @@ Required Properties:
 - compatible: Value should be "ovti,ov5645".
 - clocks: Reference to the xclk clock.
 - clock-names: Should be "xclk".
-- clock-frequency: Frequency of the xclk clock.
+- clock-frequency: Frequency of the xclk clock. Should be 24MHz with 1%
+                   acceptable tolerance.
 - enable-gpios: Chip enable GPIO. Polarity is GPIO_ACTIVE_HIGH. This corresponds
   to the hardware pin PWDNB which is physically active low.
 - reset-gpios: Chip reset GPIO. Polarity is GPIO_ACTIVE_LOW. This corresponds to
@@ -37,7 +38,7 @@ Example:
 
 			clocks = <&clks 200>;
 			clock-names = "xclk";
-			clock-frequency = <23880000>;
+			clock-frequency = <24000000>;
 
 			vdddo-supply = <&camera_dovdd_1v8>;
 			vdda-supply = <&camera_avdd_2v8>;
-- 
2.17.1


^ permalink raw reply related	[flat|nested] 3+ messages in thread

* Re: [PATCH] dt-bindings: media: i2c: Fix external clock frequency for OV5645
  2018-11-14 10:39 [PATCH] dt-bindings: media: i2c: Fix external clock frequency for OV5645 Manivannan Sadhasivam
@ 2018-11-14 10:57 ` Sakari Ailus
  2018-11-14 12:06   ` Manivannan Sadhasivam
  0 siblings, 1 reply; 3+ messages in thread
From: Sakari Ailus @ 2018-11-14 10:57 UTC (permalink / raw)
  To: Manivannan Sadhasivam
  Cc: mchehab, robh+dt, todor.tomov, hansverk, linux-media, devicetree,
	linux-kernel

Hi Manivannan,

On Wed, Nov 14, 2018 at 04:09:35PM +0530, Manivannan Sadhasivam wrote:
> Commit "4adb0a0432f4 media: ov5645: Supported external clock is 24MHz"
> modified the external clock frequency to be 24MHz instead of the
> 23.88MHz in driver. Hence, make the same change in corresponding bindings
> doc and mention the acceptable tolerance.
> 
> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> ---
>  Documentation/devicetree/bindings/media/i2c/ov5645.txt | 5 +++--
>  1 file changed, 3 insertions(+), 2 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/media/i2c/ov5645.txt b/Documentation/devicetree/bindings/media/i2c/ov5645.txt
> index fd7aec9f8e24..b155583469a4 100644
> --- a/Documentation/devicetree/bindings/media/i2c/ov5645.txt
> +++ b/Documentation/devicetree/bindings/media/i2c/ov5645.txt
> @@ -8,7 +8,8 @@ Required Properties:
>  - compatible: Value should be "ovti,ov5645".
>  - clocks: Reference to the xclk clock.
>  - clock-names: Should be "xclk".
> -- clock-frequency: Frequency of the xclk clock.
> +- clock-frequency: Frequency of the xclk clock. Should be 24MHz with 1%
> +                   acceptable tolerance.

DT bindings are for documenting the hardware, not the driver implementation.
The sensor supports a range AFAIU, not a specific frequency.

The bit below seems good.

>  - enable-gpios: Chip enable GPIO. Polarity is GPIO_ACTIVE_HIGH. This corresponds
>    to the hardware pin PWDNB which is physically active low.
>  - reset-gpios: Chip reset GPIO. Polarity is GPIO_ACTIVE_LOW. This corresponds to
> @@ -37,7 +38,7 @@ Example:
>  
>  			clocks = <&clks 200>;
>  			clock-names = "xclk";
> -			clock-frequency = <23880000>;
> +			clock-frequency = <24000000>;
>  
>  			vdddo-supply = <&camera_dovdd_1v8>;
>  			vdda-supply = <&camera_avdd_2v8>;
> -- 
> 2.17.1
> 

-- 
Sakari Ailus
e-mail: sakari.ailus@iki.fi

^ permalink raw reply	[flat|nested] 3+ messages in thread

* Re: [PATCH] dt-bindings: media: i2c: Fix external clock frequency for OV5645
  2018-11-14 10:57 ` Sakari Ailus
@ 2018-11-14 12:06   ` Manivannan Sadhasivam
  0 siblings, 0 replies; 3+ messages in thread
From: Manivannan Sadhasivam @ 2018-11-14 12:06 UTC (permalink / raw)
  To: Sakari Ailus
  Cc: mchehab, robh+dt, todor.tomov, hansverk, linux-media, devicetree,
	linux-kernel

On Wed, Nov 14, 2018 at 12:57:12PM +0200, Sakari Ailus wrote:
> Hi Manivannan,
> 
> On Wed, Nov 14, 2018 at 04:09:35PM +0530, Manivannan Sadhasivam wrote:
> > Commit "4adb0a0432f4 media: ov5645: Supported external clock is 24MHz"
> > modified the external clock frequency to be 24MHz instead of the
> > 23.88MHz in driver. Hence, make the same change in corresponding bindings
> > doc and mention the acceptable tolerance.
> > 
> > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> > ---
> >  Documentation/devicetree/bindings/media/i2c/ov5645.txt | 5 +++--
> >  1 file changed, 3 insertions(+), 2 deletions(-)
> > 
> > diff --git a/Documentation/devicetree/bindings/media/i2c/ov5645.txt b/Documentation/devicetree/bindings/media/i2c/ov5645.txt
> > index fd7aec9f8e24..b155583469a4 100644
> > --- a/Documentation/devicetree/bindings/media/i2c/ov5645.txt
> > +++ b/Documentation/devicetree/bindings/media/i2c/ov5645.txt
> > @@ -8,7 +8,8 @@ Required Properties:
> >  - compatible: Value should be "ovti,ov5645".
> >  - clocks: Reference to the xclk clock.
> >  - clock-names: Should be "xclk".
> > -- clock-frequency: Frequency of the xclk clock.
> > +- clock-frequency: Frequency of the xclk clock. Should be 24MHz with 1%
> > +                   acceptable tolerance.
> 
> DT bindings are for documenting the hardware, not the driver implementation.
> The sensor supports a range AFAIU, not a specific frequency.
>

Agree! That's my bad.

> The bit below seems good.
> 

Okay. Will remove the above change and send v2.

Thanks,
Mani

> >  - enable-gpios: Chip enable GPIO. Polarity is GPIO_ACTIVE_HIGH. This corresponds
> >    to the hardware pin PWDNB which is physically active low.
> >  - reset-gpios: Chip reset GPIO. Polarity is GPIO_ACTIVE_LOW. This corresponds to
> > @@ -37,7 +38,7 @@ Example:
> >  
> >  			clocks = <&clks 200>;
> >  			clock-names = "xclk";
> > -			clock-frequency = <23880000>;
> > +			clock-frequency = <24000000>;
> >  
> >  			vdddo-supply = <&camera_dovdd_1v8>;
> >  			vdda-supply = <&camera_avdd_2v8>;
> > -- 
> > 2.17.1
> > 
> 
> -- 
> Sakari Ailus
> e-mail: sakari.ailus@iki.fi

^ permalink raw reply	[flat|nested] 3+ messages in thread

end of thread, other threads:[~2018-11-14 12:07 UTC | newest]

Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-11-14 10:39 [PATCH] dt-bindings: media: i2c: Fix external clock frequency for OV5645 Manivannan Sadhasivam
2018-11-14 10:57 ` Sakari Ailus
2018-11-14 12:06   ` Manivannan Sadhasivam

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).