From: Nishad Kamdar <nishadkamdar@gmail.com>
To: Jonathan Cameron <jic23@jic23.retrosnub.co.uk>
Cc: Lars-Peter Clausen <lars@metafoo.de>,
Michael Hennerich <Michael.Hennerich@analog.com>,
Hartmut Knaack <knaack.h@gmx.de>,
Peter Meerwald-Stadler <pmeerw@pmeerw.net>,
Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
linux-iio@vger.kernel.org, devel@driverdev.osuosl.org,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH v3 1/4] staging: iio: ad7816: Switch to the gpio descriptor interface
Date: Wed, 14 Nov 2018 22:36:08 +0530 [thread overview]
Message-ID: <20181114170606.GA16897@nishad> (raw)
In-Reply-To: <20181111123154.176ac734@archlinux>
On Sun, Nov 11, 2018 at 12:31:54PM +0000, Jonathan Cameron wrote:
> On Sun, 11 Nov 2018 12:24:05 +0000
> Jonathan Cameron <jic23@kernel.org> wrote:
>
> > On Fri, 9 Nov 2018 13:05:17 +0530
> > Nishad Kamdar <nishadkamdar@gmail.com> wrote:
> >
> > > Use the gpiod interface for rdwr_pin, convert_pin and busy_pin
> > > instead of the deprecated old non-descriptor interface.
> > >
> > > Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
> > Applied to the togreg branch of iio.git and pushed out as testing
> > for the autobuilders to play with it.
> Actually no it isn't, because I applied the previous version back in
> October. Please avoid resending patches that have already been applied.
> It gets very confusing!
>
> Jonathan
>
Sorry about that. I'll keep that in mind.
Thanks for the review.
regards,
Nishad
>
> >
> > Thanks,
> >
> > Jonathan
> >
> > > ---
> > > drivers/staging/iio/adc/ad7816.c | 80 ++++++++++++++------------------
> > > 1 file changed, 34 insertions(+), 46 deletions(-)
> > >
> > > diff --git a/drivers/staging/iio/adc/ad7816.c b/drivers/staging/iio/adc/ad7816.c
> > > index bf76a8620bdb..12c4e0ab4713 100644
> > > --- a/drivers/staging/iio/adc/ad7816.c
> > > +++ b/drivers/staging/iio/adc/ad7816.c
> > > @@ -7,7 +7,7 @@
> > > */
> > >
> > > #include <linux/interrupt.h>
> > > -#include <linux/gpio.h>
> > > +#include <linux/gpio/consumer.h>
> > > #include <linux/device.h>
> > > #include <linux/kernel.h>
> > > #include <linux/slab.h>
> > > @@ -44,9 +44,9 @@
> > >
> > > struct ad7816_chip_info {
> > > struct spi_device *spi_dev;
> > > - u16 rdwr_pin;
> > > - u16 convert_pin;
> > > - u16 busy_pin;
> > > + struct gpio_desc *rdwr_pin;
> > > + struct gpio_desc *convert_pin;
> > > + struct gpio_desc *busy_pin;
> > > u8 oti_data[AD7816_CS_MAX + 1];
> > > u8 channel_id; /* 0 always be temperature */
> > > u8 mode;
> > > @@ -61,28 +61,28 @@ static int ad7816_spi_read(struct ad7816_chip_info *chip, u16 *data)
> > > int ret = 0;
> > > __be16 buf;
> > >
> > > - gpio_set_value(chip->rdwr_pin, 1);
> > > - gpio_set_value(chip->rdwr_pin, 0);
> > > + gpiod_set_value(chip->rdwr_pin, 1);
> > > + gpiod_set_value(chip->rdwr_pin, 0);
> > > ret = spi_write(spi_dev, &chip->channel_id, sizeof(chip->channel_id));
> > > if (ret < 0) {
> > > dev_err(&spi_dev->dev, "SPI channel setting error\n");
> > > return ret;
> > > }
> > > - gpio_set_value(chip->rdwr_pin, 1);
> > > + gpiod_set_value(chip->rdwr_pin, 1);
> > >
> > > if (chip->mode == AD7816_PD) { /* operating mode 2 */
> > > - gpio_set_value(chip->convert_pin, 1);
> > > - gpio_set_value(chip->convert_pin, 0);
> > > + gpiod_set_value(chip->convert_pin, 1);
> > > + gpiod_set_value(chip->convert_pin, 0);
> > > } else { /* operating mode 1 */
> > > - gpio_set_value(chip->convert_pin, 0);
> > > - gpio_set_value(chip->convert_pin, 1);
> > > + gpiod_set_value(chip->convert_pin, 0);
> > > + gpiod_set_value(chip->convert_pin, 1);
> > > }
> > >
> > > - while (gpio_get_value(chip->busy_pin))
> > > + while (gpiod_get_value(chip->busy_pin))
> > > cpu_relax();
> > >
> > > - gpio_set_value(chip->rdwr_pin, 0);
> > > - gpio_set_value(chip->rdwr_pin, 1);
> > > + gpiod_set_value(chip->rdwr_pin, 0);
> > > + gpiod_set_value(chip->rdwr_pin, 1);
> > > ret = spi_read(spi_dev, &buf, sizeof(*data));
> > > if (ret < 0) {
> > > dev_err(&spi_dev->dev, "SPI data read error\n");
> > > @@ -99,8 +99,8 @@ static int ad7816_spi_write(struct ad7816_chip_info *chip, u8 data)
> > > struct spi_device *spi_dev = chip->spi_dev;
> > > int ret = 0;
> > >
> > > - gpio_set_value(chip->rdwr_pin, 1);
> > > - gpio_set_value(chip->rdwr_pin, 0);
> > > + gpiod_set_value(chip->rdwr_pin, 1);
> > > + gpiod_set_value(chip->rdwr_pin, 0);
> > > ret = spi_write(spi_dev, &data, sizeof(data));
> > > if (ret < 0)
> > > dev_err(&spi_dev->dev, "SPI oti data write error\n");
> > > @@ -129,10 +129,10 @@ static ssize_t ad7816_store_mode(struct device *dev,
> > > struct ad7816_chip_info *chip = iio_priv(indio_dev);
> > >
> > > if (strcmp(buf, "full")) {
> > > - gpio_set_value(chip->rdwr_pin, 1);
> > > + gpiod_set_value(chip->rdwr_pin, 1);
> > > chip->mode = AD7816_FULL;
> > > } else {
> > > - gpio_set_value(chip->rdwr_pin, 0);
> > > + gpiod_set_value(chip->rdwr_pin, 0);
> > > chip->mode = AD7816_PD;
> > > }
> > >
> > > @@ -345,15 +345,9 @@ static int ad7816_probe(struct spi_device *spi_dev)
> > > {
> > > struct ad7816_chip_info *chip;
> > > struct iio_dev *indio_dev;
> > > - unsigned short *pins = dev_get_platdata(&spi_dev->dev);
> > > int ret = 0;
> > > int i;
> > >
> > > - if (!pins) {
> > > - dev_err(&spi_dev->dev, "No necessary GPIO platform data.\n");
> > > - return -EINVAL;
> > > - }
> > > -
> > > indio_dev = devm_iio_device_alloc(&spi_dev->dev, sizeof(*chip));
> > > if (!indio_dev)
> > > return -ENOMEM;
> > > @@ -364,34 +358,28 @@ static int ad7816_probe(struct spi_device *spi_dev)
> > > chip->spi_dev = spi_dev;
> > > for (i = 0; i <= AD7816_CS_MAX; i++)
> > > chip->oti_data[i] = 203;
> > > - chip->rdwr_pin = pins[0];
> > > - chip->convert_pin = pins[1];
> > > - chip->busy_pin = pins[2];
> > > -
> > > - ret = devm_gpio_request(&spi_dev->dev, chip->rdwr_pin,
> > > - spi_get_device_id(spi_dev)->name);
> > > - if (ret) {
> > > - dev_err(&spi_dev->dev, "Fail to request rdwr gpio PIN %d.\n",
> > > - chip->rdwr_pin);
> > > +
> > > + chip->rdwr_pin = devm_gpiod_get(&spi_dev->dev, "rdwr", GPIOD_IN);
> > > + if (IS_ERR(chip->rdwr_pin)) {
> > > + ret = PTR_ERR(chip->rdwr_pin);
> > > + dev_err(&spi_dev->dev, "Failed to request rdwr GPIO: %d\n",
> > > + ret);
> > > return ret;
> > > }
> > > - gpio_direction_input(chip->rdwr_pin);
> > > - ret = devm_gpio_request(&spi_dev->dev, chip->convert_pin,
> > > - spi_get_device_id(spi_dev)->name);
> > > - if (ret) {
> > > - dev_err(&spi_dev->dev, "Fail to request convert gpio PIN %d.\n",
> > > - chip->convert_pin);
> > > + chip->convert_pin = devm_gpiod_get(&spi_dev->dev, "convert", GPIOD_IN);
> > > + if (IS_ERR(chip->convert_pin)) {
> > > + ret = PTR_ERR(chip->convert_pin);
> > > + dev_err(&spi_dev->dev, "Failed to request convert GPIO: %d\n",
> > > + ret);
> > > return ret;
> > > }
> > > - gpio_direction_input(chip->convert_pin);
> > > - ret = devm_gpio_request(&spi_dev->dev, chip->busy_pin,
> > > - spi_get_device_id(spi_dev)->name);
> > > - if (ret) {
> > > - dev_err(&spi_dev->dev, "Fail to request busy gpio PIN %d.\n",
> > > - chip->busy_pin);
> > > + chip->busy_pin = devm_gpiod_get(&spi_dev->dev, "busy", GPIOD_IN);
> > > + if (IS_ERR(chip->busy_pin)) {
> > > + ret = PTR_ERR(chip->busy_pin);
> > > + dev_err(&spi_dev->dev, "Failed to request busy GPIO: %d\n",
> > > + ret);
> > > return ret;
> > > }
> > > - gpio_direction_input(chip->busy_pin);
> > >
> > > indio_dev->name = spi_get_device_id(spi_dev)->name;
> > > indio_dev->dev.parent = &spi_dev->dev;
> >
>
next prev parent reply other threads:[~2018-11-14 17:06 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-11-09 7:34 [PATCH v3 0/4] staging: iio: ad7816: Switch to the gpio descriptor interface Nishad Kamdar
2018-11-09 7:35 ` [PATCH v3 1/4] " Nishad Kamdar
2018-11-09 8:05 ` Ardelean, Alexandru
2018-11-09 8:08 ` Ardelean, Alexandru
2018-11-11 12:24 ` Jonathan Cameron
2018-11-11 12:31 ` Jonathan Cameron
2018-11-14 17:06 ` Nishad Kamdar [this message]
2018-11-09 7:36 ` [PATCH v3 2/4] staging: iio: ad7816: Do not use busy_pin in case of AD7818 Nishad Kamdar
2018-11-11 12:35 ` Jonathan Cameron
2018-11-09 7:37 ` [PATCH v3 3/4] staging: iio: ad7816: Set RD/WR pin and CONVST pin as outputs Nishad Kamdar
2018-11-11 12:36 ` Jonathan Cameron
2018-11-09 7:38 ` [PATCH v3 4/4] staging: iio: ad7816: Add device tree table Nishad Kamdar
2018-11-09 8:11 ` Ardelean, Alexandru
2018-11-11 12:38 ` Jonathan Cameron
2018-11-14 16:54 ` Nishad Kamdar
2018-11-14 16:29 ` Nishad Kamdar
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181114170606.GA16897@nishad \
--to=nishadkamdar@gmail.com \
--cc=Michael.Hennerich@analog.com \
--cc=devel@driverdev.osuosl.org \
--cc=gregkh@linuxfoundation.org \
--cc=jic23@jic23.retrosnub.co.uk \
--cc=knaack.h@gmx.de \
--cc=lars@metafoo.de \
--cc=linux-iio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=pmeerw@pmeerw.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).