* [PATCH] clk: qcom: Enumerate remaining msm8998 resets
@ 2018-12-04 15:13 Jeffrey Hugo
2018-12-04 17:04 ` Bjorn Andersson
2018-12-05 23:57 ` Stephen Boyd
0 siblings, 2 replies; 3+ messages in thread
From: Jeffrey Hugo @ 2018-12-04 15:13 UTC (permalink / raw)
To: andy.gross, david.brown, mturquette, sboyd
Cc: bjorn.andersson, linux-arm-msm, linux-clk, linux-kernel, Jeffrey Hugo
The current list of defined resets is incomplete compared to what the
hardware implements. Enumerate the remaining resets according to the
hardware documentation.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
---
Based upon "Merge branch 'clk-qcom-8998-resets' into clk-next" to hopefully
avoid any merge conflicts.
drivers/clk/qcom/gcc-msm8998.c | 87 ++++++++++++++++++++++++++++
include/dt-bindings/clock/qcom,gcc-msm8998.h | 87 ++++++++++++++++++++++++++++
2 files changed, 174 insertions(+)
diff --git a/drivers/clk/qcom/gcc-msm8998.c b/drivers/clk/qcom/gcc-msm8998.c
index c3bb9ff..14c507d 100644
--- a/drivers/clk/qcom/gcc-msm8998.c
+++ b/drivers/clk/qcom/gcc-msm8998.c
@@ -2761,6 +2761,93 @@ enum {
[GCC_TSIF_BCR] = { 0x36000 },
[GCC_UFS_BCR] = { 0x75000 },
[GCC_USB_30_BCR] = { 0xf000 },
+ [GCC_SYSTEM_NOC_BCR] = { 0x4000 },
+ [GCC_CONFIG_NOC_BCR] = { 0x5000 },
+ [GCC_AHB2PHY_EAST_BCR] = { 0x7000 },
+ [GCC_IMEM_BCR] = { 0x8000 },
+ [GCC_PIMEM_BCR] = { 0xa000 },
+ [GCC_MMSS_BCR] = { 0xb000 },
+ [GCC_QDSS_BCR] = { 0xc000 },
+ [GCC_WCSS_BCR] = { 0x11000 },
+ [GCC_BLSP1_BCR] = { 0x17000 },
+ [GCC_BLSP1_UART1_BCR] = { 0x1a000 },
+ [GCC_BLSP1_UART2_BCR] = { 0x1c000 },
+ [GCC_BLSP1_UART3_BCR] = { 0x1e000 },
+ [GCC_CM_PHY_REFGEN1_BCR] = { 0x22000 },
+ [GCC_CM_PHY_REFGEN2_BCR] = { 0x24000 },
+ [GCC_BLSP2_BCR] = { 0x25000 },
+ [GCC_BLSP2_UART1_BCR] = { 0x27000 },
+ [GCC_BLSP2_UART2_BCR] = { 0x29000 },
+ [GCC_BLSP2_UART3_BCR] = { 0x2b000 },
+ [GCC_SRAM_SENSOR_BCR] = { 0x2d000 },
+ [GCC_PRNG_BCR] = { 0x34000 },
+ [GCC_TSIF_0_RESET] = { 0x36024 },
+ [GCC_TSIF_1_RESET] = { 0x36028 },
+ [GCC_TCSR_BCR] = { 0x37000 },
+ [GCC_BOOT_ROM_BCR] = { 0x38000 },
+ [GCC_MSG_RAM_BCR] = { 0x39000 },
+ [GCC_TLMM_BCR] = { 0x3a000 },
+ [GCC_MPM_BCR] = { 0x3b000 },
+ [GCC_SEC_CTRL_BCR] = { 0x3d000 },
+ [GCC_SPMI_BCR] = { 0x3f000 },
+ [GCC_SPDM_BCR] = { 0x40000 },
+ [GCC_CE1_BCR] = { 0x41000 },
+ [GCC_BIMC_BCR] = { 0x44000 },
+ [GCC_SNOC_BUS_TIMEOUT0_BCR] = { 0x49000 },
+ [GCC_SNOC_BUS_TIMEOUT1_BCR] = { 0x49008 },
+ [GCC_SNOC_BUS_TIMEOUT3_BCR] = { 0x49010 },
+ [GCC_SNOC_BUS_TIMEOUT_EXTREF_BCR] = { 0x49018 },
+ [GCC_PNOC_BUS_TIMEOUT0_BCR] = { 0x4a000 },
+ [GCC_CNOC_PERIPH_BUS_TIMEOUT1_BCR] = { 0x4a004 },
+ [GCC_CNOC_PERIPH_BUS_TIMEOUT2_BCR] = { 0x4a00c },
+ [GCC_CNOC_BUS_TIMEOUT0_BCR] = { 0x4b000 },
+ [GCC_CNOC_BUS_TIMEOUT1_BCR] = { 0x4b008 },
+ [GCC_CNOC_BUS_TIMEOUT2_BCR] = { 0x4b010 },
+ [GCC_CNOC_BUS_TIMEOUT3_BCR] = { 0x4b018 },
+ [GCC_CNOC_BUS_TIMEOUT4_BCR] = { 0x4b020 },
+ [GCC_CNOC_BUS_TIMEOUT5_BCR] = { 0x4b028 },
+ [GCC_CNOC_BUS_TIMEOUT6_BCR] = { 0x4b030 },
+ [GCC_CNOC_BUS_TIMEOUT7_BCR] = { 0x4b038 },
+ [GCC_APB2JTAG_BCR] = { 0x4c000 },
+ [GCC_RBCPR_CX_BCR] = { 0x4e000 },
+ [GCC_RBCPR_MX_BCR] = { 0x4f000 },
+ [GCC_USB3_PHY_BCR] = { 0x50020 },
+ [GCC_USB3PHY_PHY_BCR] = { 0x50024 },
+ [GCC_USB3_DP_PHY_BCR] = { 0x50028 },
+ [GCC_SSC_BCR] = { 0x63000 },
+ [GCC_SSC_RESET] = { 0x63020 },
+ [GCC_USB_PHY_CFG_AHB2PHY_BCR] = { 0x6a000 },
+ [GCC_PCIE_0_LINK_DOWN_BCR] = { 0x6c014 },
+ [GCC_PCIE_0_PHY_BCR] = { 0x6c01c },
+ [GCC_PCIE_0_NOCSR_COM_PHY_BCR] = { 0x6c020 },
+ [GCC_PCIE_PHY_BCR] = { 0x6f000 },
+ [GCC_PCIE_PHY_NOCSR_COM_PHY_BCR] = { 0x6f00c },
+ [GCC_PCIE_PHY_CFG_AHB_BCR] = { 0x6f010 },
+ [GCC_PCIE_PHY_COM_BCR] = { 0x6f014 },
+ [GCC_GPU_BCR] = { 0x71000 },
+ [GCC_SPSS_BCR] = { 0x72000 },
+ [GCC_OBT_ODT_BCR] = { 0x73000 },
+ [GCC_VS_BCR] = { 0x7a000 },
+ [GCC_MSS_VS_RESET] = { 0x7a100 },
+ [GCC_GPU_VS_RESET] = { 0x7a104 },
+ [GCC_APC0_VS_RESET] = { 0x7a108 },
+ [GCC_APC1_VS_RESET] = { 0x7a10c },
+ [GCC_CNOC_BUS_TIMEOUT8_BCR] = { 0x80000 },
+ [GCC_CNOC_BUS_TIMEOUT9_BCR] = { 0x80008 },
+ [GCC_CNOC_BUS_TIMEOUT10_BCR] = { 0x80010 },
+ [GCC_CNOC_BUS_TIMEOUT11_BCR] = { 0x80018 },
+ [GCC_CNOC_BUS_TIMEOUT12_BCR] = { 0x80020 },
+ [GCC_CNOC_BUS_TIMEOUT13_BCR] = { 0x80028 },
+ [GCC_CNOC_BUS_TIMEOUT14_BCR] = { 0x80030 },
+ [GCC_CNOC_BUS_TIMEOUT_EXTREF_BCR] = { 0x80038 },
+ [GCC_AGGRE1_NOC_BCR] = { 0x82000 },
+ [GCC_AGGRE2_NOC_BCR] = { 0x83000 },
+ [GCC_DCC_BCR] = { 0x84000 },
+ [GCC_QREFS_VBG_CAL_BCR] = { 0x88028 },
+ [GCC_IPA_BCR] = { 0x89000 },
+ [GCC_GLM_BCR] = { 0x8b000 },
+ [GCC_SKL_BCR] = { 0x8c000 },
+ [GCC_MSMPU_BCR] = { 0x8d000 },
};
static const struct regmap_config gcc_msm8998_regmap_config = {
diff --git a/include/dt-bindings/clock/qcom,gcc-msm8998.h b/include/dt-bindings/clock/qcom,gcc-msm8998.h
index 58a242e..c751a40 100644
--- a/include/dt-bindings/clock/qcom,gcc-msm8998.h
+++ b/include/dt-bindings/clock/qcom,gcc-msm8998.h
@@ -204,5 +204,92 @@
#define GCC_TSIF_BCR 16
#define GCC_UFS_BCR 17
#define GCC_USB_30_BCR 18
+#define GCC_SYSTEM_NOC_BCR 19
+#define GCC_CONFIG_NOC_BCR 20
+#define GCC_AHB2PHY_EAST_BCR 21
+#define GCC_IMEM_BCR 22
+#define GCC_PIMEM_BCR 23
+#define GCC_MMSS_BCR 24
+#define GCC_QDSS_BCR 25
+#define GCC_WCSS_BCR 26
+#define GCC_BLSP1_BCR 27
+#define GCC_BLSP1_UART1_BCR 28
+#define GCC_BLSP1_UART2_BCR 29
+#define GCC_BLSP1_UART3_BCR 30
+#define GCC_CM_PHY_REFGEN1_BCR 31
+#define GCC_CM_PHY_REFGEN2_BCR 32
+#define GCC_BLSP2_BCR 33
+#define GCC_BLSP2_UART1_BCR 34
+#define GCC_BLSP2_UART2_BCR 35
+#define GCC_BLSP2_UART3_BCR 36
+#define GCC_SRAM_SENSOR_BCR 37
+#define GCC_PRNG_BCR 38
+#define GCC_TSIF_0_RESET 39
+#define GCC_TSIF_1_RESET 40
+#define GCC_TCSR_BCR 41
+#define GCC_BOOT_ROM_BCR 42
+#define GCC_MSG_RAM_BCR 43
+#define GCC_TLMM_BCR 44
+#define GCC_MPM_BCR 45
+#define GCC_SEC_CTRL_BCR 46
+#define GCC_SPMI_BCR 47
+#define GCC_SPDM_BCR 48
+#define GCC_CE1_BCR 49
+#define GCC_BIMC_BCR 50
+#define GCC_SNOC_BUS_TIMEOUT0_BCR 51
+#define GCC_SNOC_BUS_TIMEOUT1_BCR 52
+#define GCC_SNOC_BUS_TIMEOUT3_BCR 53
+#define GCC_SNOC_BUS_TIMEOUT_EXTREF_BCR 54
+#define GCC_PNOC_BUS_TIMEOUT0_BCR 55
+#define GCC_CNOC_PERIPH_BUS_TIMEOUT1_BCR 56
+#define GCC_CNOC_PERIPH_BUS_TIMEOUT2_BCR 57
+#define GCC_CNOC_BUS_TIMEOUT0_BCR 58
+#define GCC_CNOC_BUS_TIMEOUT1_BCR 59
+#define GCC_CNOC_BUS_TIMEOUT2_BCR 60
+#define GCC_CNOC_BUS_TIMEOUT3_BCR 61
+#define GCC_CNOC_BUS_TIMEOUT4_BCR 62
+#define GCC_CNOC_BUS_TIMEOUT5_BCR 63
+#define GCC_CNOC_BUS_TIMEOUT6_BCR 64
+#define GCC_CNOC_BUS_TIMEOUT7_BCR 65
+#define GCC_APB2JTAG_BCR 66
+#define GCC_RBCPR_CX_BCR 67
+#define GCC_RBCPR_MX_BCR 68
+#define GCC_USB3_PHY_BCR 69
+#define GCC_USB3PHY_PHY_BCR 70
+#define GCC_USB3_DP_PHY_BCR 71
+#define GCC_SSC_BCR 72
+#define GCC_SSC_RESET 73
+#define GCC_USB_PHY_CFG_AHB2PHY_BCR 74
+#define GCC_PCIE_0_LINK_DOWN_BCR 75
+#define GCC_PCIE_0_PHY_BCR 76
+#define GCC_PCIE_0_NOCSR_COM_PHY_BCR 77
+#define GCC_PCIE_PHY_BCR 78
+#define GCC_PCIE_PHY_NOCSR_COM_PHY_BCR 79
+#define GCC_PCIE_PHY_CFG_AHB_BCR 80
+#define GCC_PCIE_PHY_COM_BCR 81
+#define GCC_GPU_BCR 82
+#define GCC_SPSS_BCR 83
+#define GCC_OBT_ODT_BCR 84
+#define GCC_VS_BCR 85
+#define GCC_MSS_VS_RESET 86
+#define GCC_GPU_VS_RESET 87
+#define GCC_APC0_VS_RESET 88
+#define GCC_APC1_VS_RESET 89
+#define GCC_CNOC_BUS_TIMEOUT8_BCR 90
+#define GCC_CNOC_BUS_TIMEOUT9_BCR 91
+#define GCC_CNOC_BUS_TIMEOUT10_BCR 92
+#define GCC_CNOC_BUS_TIMEOUT11_BCR 93
+#define GCC_CNOC_BUS_TIMEOUT12_BCR 94
+#define GCC_CNOC_BUS_TIMEOUT13_BCR 95
+#define GCC_CNOC_BUS_TIMEOUT14_BCR 96
+#define GCC_CNOC_BUS_TIMEOUT_EXTREF_BCR 97
+#define GCC_AGGRE1_NOC_BCR 98
+#define GCC_AGGRE2_NOC_BCR 99
+#define GCC_DCC_BCR 100
+#define GCC_QREFS_VBG_CAL_BCR 101
+#define GCC_IPA_BCR 102
+#define GCC_GLM_BCR 103
+#define GCC_SKL_BCR 104
+#define GCC_MSMPU_BCR 105
#endif
--
Qualcomm Datacenter Technologies as an affiliate of Qualcomm Technologies, Inc.
Qualcomm Technologies, Inc. is a member of the
Code Aurora Forum, a Linux Foundation Collaborative Project.
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH] clk: qcom: Enumerate remaining msm8998 resets
2018-12-04 15:13 [PATCH] clk: qcom: Enumerate remaining msm8998 resets Jeffrey Hugo
@ 2018-12-04 17:04 ` Bjorn Andersson
2018-12-05 23:57 ` Stephen Boyd
1 sibling, 0 replies; 3+ messages in thread
From: Bjorn Andersson @ 2018-12-04 17:04 UTC (permalink / raw)
To: Jeffrey Hugo
Cc: andy.gross, david.brown, mturquette, sboyd, linux-arm-msm,
linux-clk, linux-kernel
On Tue 04 Dec 07:13 PST 2018, Jeffrey Hugo wrote:
> The current list of defined resets is incomplete compared to what the
> hardware implements. Enumerate the remaining resets according to the
> hardware documentation.
>
> Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Regards,
Bjorn
> ---
>
> Based upon "Merge branch 'clk-qcom-8998-resets' into clk-next" to hopefully
> avoid any merge conflicts.
>
> drivers/clk/qcom/gcc-msm8998.c | 87 ++++++++++++++++++++++++++++
> include/dt-bindings/clock/qcom,gcc-msm8998.h | 87 ++++++++++++++++++++++++++++
> 2 files changed, 174 insertions(+)
>
> diff --git a/drivers/clk/qcom/gcc-msm8998.c b/drivers/clk/qcom/gcc-msm8998.c
> index c3bb9ff..14c507d 100644
> --- a/drivers/clk/qcom/gcc-msm8998.c
> +++ b/drivers/clk/qcom/gcc-msm8998.c
> @@ -2761,6 +2761,93 @@ enum {
> [GCC_TSIF_BCR] = { 0x36000 },
> [GCC_UFS_BCR] = { 0x75000 },
> [GCC_USB_30_BCR] = { 0xf000 },
> + [GCC_SYSTEM_NOC_BCR] = { 0x4000 },
> + [GCC_CONFIG_NOC_BCR] = { 0x5000 },
> + [GCC_AHB2PHY_EAST_BCR] = { 0x7000 },
> + [GCC_IMEM_BCR] = { 0x8000 },
> + [GCC_PIMEM_BCR] = { 0xa000 },
> + [GCC_MMSS_BCR] = { 0xb000 },
> + [GCC_QDSS_BCR] = { 0xc000 },
> + [GCC_WCSS_BCR] = { 0x11000 },
> + [GCC_BLSP1_BCR] = { 0x17000 },
> + [GCC_BLSP1_UART1_BCR] = { 0x1a000 },
> + [GCC_BLSP1_UART2_BCR] = { 0x1c000 },
> + [GCC_BLSP1_UART3_BCR] = { 0x1e000 },
> + [GCC_CM_PHY_REFGEN1_BCR] = { 0x22000 },
> + [GCC_CM_PHY_REFGEN2_BCR] = { 0x24000 },
> + [GCC_BLSP2_BCR] = { 0x25000 },
> + [GCC_BLSP2_UART1_BCR] = { 0x27000 },
> + [GCC_BLSP2_UART2_BCR] = { 0x29000 },
> + [GCC_BLSP2_UART3_BCR] = { 0x2b000 },
> + [GCC_SRAM_SENSOR_BCR] = { 0x2d000 },
> + [GCC_PRNG_BCR] = { 0x34000 },
> + [GCC_TSIF_0_RESET] = { 0x36024 },
> + [GCC_TSIF_1_RESET] = { 0x36028 },
> + [GCC_TCSR_BCR] = { 0x37000 },
> + [GCC_BOOT_ROM_BCR] = { 0x38000 },
> + [GCC_MSG_RAM_BCR] = { 0x39000 },
> + [GCC_TLMM_BCR] = { 0x3a000 },
> + [GCC_MPM_BCR] = { 0x3b000 },
> + [GCC_SEC_CTRL_BCR] = { 0x3d000 },
> + [GCC_SPMI_BCR] = { 0x3f000 },
> + [GCC_SPDM_BCR] = { 0x40000 },
> + [GCC_CE1_BCR] = { 0x41000 },
> + [GCC_BIMC_BCR] = { 0x44000 },
> + [GCC_SNOC_BUS_TIMEOUT0_BCR] = { 0x49000 },
> + [GCC_SNOC_BUS_TIMEOUT1_BCR] = { 0x49008 },
> + [GCC_SNOC_BUS_TIMEOUT3_BCR] = { 0x49010 },
> + [GCC_SNOC_BUS_TIMEOUT_EXTREF_BCR] = { 0x49018 },
> + [GCC_PNOC_BUS_TIMEOUT0_BCR] = { 0x4a000 },
> + [GCC_CNOC_PERIPH_BUS_TIMEOUT1_BCR] = { 0x4a004 },
> + [GCC_CNOC_PERIPH_BUS_TIMEOUT2_BCR] = { 0x4a00c },
> + [GCC_CNOC_BUS_TIMEOUT0_BCR] = { 0x4b000 },
> + [GCC_CNOC_BUS_TIMEOUT1_BCR] = { 0x4b008 },
> + [GCC_CNOC_BUS_TIMEOUT2_BCR] = { 0x4b010 },
> + [GCC_CNOC_BUS_TIMEOUT3_BCR] = { 0x4b018 },
> + [GCC_CNOC_BUS_TIMEOUT4_BCR] = { 0x4b020 },
> + [GCC_CNOC_BUS_TIMEOUT5_BCR] = { 0x4b028 },
> + [GCC_CNOC_BUS_TIMEOUT6_BCR] = { 0x4b030 },
> + [GCC_CNOC_BUS_TIMEOUT7_BCR] = { 0x4b038 },
> + [GCC_APB2JTAG_BCR] = { 0x4c000 },
> + [GCC_RBCPR_CX_BCR] = { 0x4e000 },
> + [GCC_RBCPR_MX_BCR] = { 0x4f000 },
> + [GCC_USB3_PHY_BCR] = { 0x50020 },
> + [GCC_USB3PHY_PHY_BCR] = { 0x50024 },
> + [GCC_USB3_DP_PHY_BCR] = { 0x50028 },
> + [GCC_SSC_BCR] = { 0x63000 },
> + [GCC_SSC_RESET] = { 0x63020 },
> + [GCC_USB_PHY_CFG_AHB2PHY_BCR] = { 0x6a000 },
> + [GCC_PCIE_0_LINK_DOWN_BCR] = { 0x6c014 },
> + [GCC_PCIE_0_PHY_BCR] = { 0x6c01c },
> + [GCC_PCIE_0_NOCSR_COM_PHY_BCR] = { 0x6c020 },
> + [GCC_PCIE_PHY_BCR] = { 0x6f000 },
> + [GCC_PCIE_PHY_NOCSR_COM_PHY_BCR] = { 0x6f00c },
> + [GCC_PCIE_PHY_CFG_AHB_BCR] = { 0x6f010 },
> + [GCC_PCIE_PHY_COM_BCR] = { 0x6f014 },
> + [GCC_GPU_BCR] = { 0x71000 },
> + [GCC_SPSS_BCR] = { 0x72000 },
> + [GCC_OBT_ODT_BCR] = { 0x73000 },
> + [GCC_VS_BCR] = { 0x7a000 },
> + [GCC_MSS_VS_RESET] = { 0x7a100 },
> + [GCC_GPU_VS_RESET] = { 0x7a104 },
> + [GCC_APC0_VS_RESET] = { 0x7a108 },
> + [GCC_APC1_VS_RESET] = { 0x7a10c },
> + [GCC_CNOC_BUS_TIMEOUT8_BCR] = { 0x80000 },
> + [GCC_CNOC_BUS_TIMEOUT9_BCR] = { 0x80008 },
> + [GCC_CNOC_BUS_TIMEOUT10_BCR] = { 0x80010 },
> + [GCC_CNOC_BUS_TIMEOUT11_BCR] = { 0x80018 },
> + [GCC_CNOC_BUS_TIMEOUT12_BCR] = { 0x80020 },
> + [GCC_CNOC_BUS_TIMEOUT13_BCR] = { 0x80028 },
> + [GCC_CNOC_BUS_TIMEOUT14_BCR] = { 0x80030 },
> + [GCC_CNOC_BUS_TIMEOUT_EXTREF_BCR] = { 0x80038 },
> + [GCC_AGGRE1_NOC_BCR] = { 0x82000 },
> + [GCC_AGGRE2_NOC_BCR] = { 0x83000 },
> + [GCC_DCC_BCR] = { 0x84000 },
> + [GCC_QREFS_VBG_CAL_BCR] = { 0x88028 },
> + [GCC_IPA_BCR] = { 0x89000 },
> + [GCC_GLM_BCR] = { 0x8b000 },
> + [GCC_SKL_BCR] = { 0x8c000 },
> + [GCC_MSMPU_BCR] = { 0x8d000 },
> };
>
> static const struct regmap_config gcc_msm8998_regmap_config = {
> diff --git a/include/dt-bindings/clock/qcom,gcc-msm8998.h b/include/dt-bindings/clock/qcom,gcc-msm8998.h
> index 58a242e..c751a40 100644
> --- a/include/dt-bindings/clock/qcom,gcc-msm8998.h
> +++ b/include/dt-bindings/clock/qcom,gcc-msm8998.h
> @@ -204,5 +204,92 @@
> #define GCC_TSIF_BCR 16
> #define GCC_UFS_BCR 17
> #define GCC_USB_30_BCR 18
> +#define GCC_SYSTEM_NOC_BCR 19
> +#define GCC_CONFIG_NOC_BCR 20
> +#define GCC_AHB2PHY_EAST_BCR 21
> +#define GCC_IMEM_BCR 22
> +#define GCC_PIMEM_BCR 23
> +#define GCC_MMSS_BCR 24
> +#define GCC_QDSS_BCR 25
> +#define GCC_WCSS_BCR 26
> +#define GCC_BLSP1_BCR 27
> +#define GCC_BLSP1_UART1_BCR 28
> +#define GCC_BLSP1_UART2_BCR 29
> +#define GCC_BLSP1_UART3_BCR 30
> +#define GCC_CM_PHY_REFGEN1_BCR 31
> +#define GCC_CM_PHY_REFGEN2_BCR 32
> +#define GCC_BLSP2_BCR 33
> +#define GCC_BLSP2_UART1_BCR 34
> +#define GCC_BLSP2_UART2_BCR 35
> +#define GCC_BLSP2_UART3_BCR 36
> +#define GCC_SRAM_SENSOR_BCR 37
> +#define GCC_PRNG_BCR 38
> +#define GCC_TSIF_0_RESET 39
> +#define GCC_TSIF_1_RESET 40
> +#define GCC_TCSR_BCR 41
> +#define GCC_BOOT_ROM_BCR 42
> +#define GCC_MSG_RAM_BCR 43
> +#define GCC_TLMM_BCR 44
> +#define GCC_MPM_BCR 45
> +#define GCC_SEC_CTRL_BCR 46
> +#define GCC_SPMI_BCR 47
> +#define GCC_SPDM_BCR 48
> +#define GCC_CE1_BCR 49
> +#define GCC_BIMC_BCR 50
> +#define GCC_SNOC_BUS_TIMEOUT0_BCR 51
> +#define GCC_SNOC_BUS_TIMEOUT1_BCR 52
> +#define GCC_SNOC_BUS_TIMEOUT3_BCR 53
> +#define GCC_SNOC_BUS_TIMEOUT_EXTREF_BCR 54
> +#define GCC_PNOC_BUS_TIMEOUT0_BCR 55
> +#define GCC_CNOC_PERIPH_BUS_TIMEOUT1_BCR 56
> +#define GCC_CNOC_PERIPH_BUS_TIMEOUT2_BCR 57
> +#define GCC_CNOC_BUS_TIMEOUT0_BCR 58
> +#define GCC_CNOC_BUS_TIMEOUT1_BCR 59
> +#define GCC_CNOC_BUS_TIMEOUT2_BCR 60
> +#define GCC_CNOC_BUS_TIMEOUT3_BCR 61
> +#define GCC_CNOC_BUS_TIMEOUT4_BCR 62
> +#define GCC_CNOC_BUS_TIMEOUT5_BCR 63
> +#define GCC_CNOC_BUS_TIMEOUT6_BCR 64
> +#define GCC_CNOC_BUS_TIMEOUT7_BCR 65
> +#define GCC_APB2JTAG_BCR 66
> +#define GCC_RBCPR_CX_BCR 67
> +#define GCC_RBCPR_MX_BCR 68
> +#define GCC_USB3_PHY_BCR 69
> +#define GCC_USB3PHY_PHY_BCR 70
> +#define GCC_USB3_DP_PHY_BCR 71
> +#define GCC_SSC_BCR 72
> +#define GCC_SSC_RESET 73
> +#define GCC_USB_PHY_CFG_AHB2PHY_BCR 74
> +#define GCC_PCIE_0_LINK_DOWN_BCR 75
> +#define GCC_PCIE_0_PHY_BCR 76
> +#define GCC_PCIE_0_NOCSR_COM_PHY_BCR 77
> +#define GCC_PCIE_PHY_BCR 78
> +#define GCC_PCIE_PHY_NOCSR_COM_PHY_BCR 79
> +#define GCC_PCIE_PHY_CFG_AHB_BCR 80
> +#define GCC_PCIE_PHY_COM_BCR 81
> +#define GCC_GPU_BCR 82
> +#define GCC_SPSS_BCR 83
> +#define GCC_OBT_ODT_BCR 84
> +#define GCC_VS_BCR 85
> +#define GCC_MSS_VS_RESET 86
> +#define GCC_GPU_VS_RESET 87
> +#define GCC_APC0_VS_RESET 88
> +#define GCC_APC1_VS_RESET 89
> +#define GCC_CNOC_BUS_TIMEOUT8_BCR 90
> +#define GCC_CNOC_BUS_TIMEOUT9_BCR 91
> +#define GCC_CNOC_BUS_TIMEOUT10_BCR 92
> +#define GCC_CNOC_BUS_TIMEOUT11_BCR 93
> +#define GCC_CNOC_BUS_TIMEOUT12_BCR 94
> +#define GCC_CNOC_BUS_TIMEOUT13_BCR 95
> +#define GCC_CNOC_BUS_TIMEOUT14_BCR 96
> +#define GCC_CNOC_BUS_TIMEOUT_EXTREF_BCR 97
> +#define GCC_AGGRE1_NOC_BCR 98
> +#define GCC_AGGRE2_NOC_BCR 99
> +#define GCC_DCC_BCR 100
> +#define GCC_QREFS_VBG_CAL_BCR 101
> +#define GCC_IPA_BCR 102
> +#define GCC_GLM_BCR 103
> +#define GCC_SKL_BCR 104
> +#define GCC_MSMPU_BCR 105
>
> #endif
> --
> Qualcomm Datacenter Technologies as an affiliate of Qualcomm Technologies, Inc.
> Qualcomm Technologies, Inc. is a member of the
> Code Aurora Forum, a Linux Foundation Collaborative Project.
>
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH] clk: qcom: Enumerate remaining msm8998 resets
2018-12-04 15:13 [PATCH] clk: qcom: Enumerate remaining msm8998 resets Jeffrey Hugo
2018-12-04 17:04 ` Bjorn Andersson
@ 2018-12-05 23:57 ` Stephen Boyd
1 sibling, 0 replies; 3+ messages in thread
From: Stephen Boyd @ 2018-12-05 23:57 UTC (permalink / raw)
To: Jeffrey Hugo, andy.gross, david.brown, mturquette
Cc: bjorn.andersson, linux-arm-msm, linux-clk, linux-kernel, Jeffrey Hugo
Quoting Jeffrey Hugo (2018-12-04 07:13:22)
> The current list of defined resets is incomplete compared to what the
> hardware implements. Enumerate the remaining resets according to the
> hardware documentation.
>
> Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
> ---
Applied to clk-next
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2018-12-05 23:57 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-12-04 15:13 [PATCH] clk: qcom: Enumerate remaining msm8998 resets Jeffrey Hugo
2018-12-04 17:04 ` Bjorn Andersson
2018-12-05 23:57 ` Stephen Boyd
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).