From: Jonathan Cameron <jic23@kernel.org>
To: Philippe Schenker <dev@pschenker.ch>
Cc: marcel.ziswiler@toradex.com, stefan@agner.ch,
Max Krummenacher <max.krummenacher@toradex.com>,
devicetree@vger.kernel.org, linux-iio@vger.kernel.org,
Hartmut Knaack <knaack.h@gmx.de>,
Alexandre Torgue <alexandre.torgue@st.com>,
linux-input@vger.kernel.org, linux-kernel@vger.kernel.org,
Rob Herring <robh+dt@kernel.org>,
Dmitry Torokhov <dmitry.torokhov@gmail.com>,
Lee Jones <lee.jones@linaro.org>,
Maxime Coquelin <mcoquelin.stm32@gmail.com>,
Mark Rutland <mark.rutland@arm.com>,
Peter Meerwald-Stadler <pmeerw@pmeerw.net>,
linux-stm32@st-md-mailman.stormreply.com,
linux-arm-kernel@lists.infradead.org,
Lars-Peter Clausen <lars@metafoo.de>
Subject: Re: [PATCH v3 3/4] iio: adc: add STMPE ADC devicetree bindings
Date: Sat, 8 Dec 2018 10:55:53 +0000 [thread overview]
Message-ID: <20181208105553.61d51b7a@archlinux> (raw)
In-Reply-To: <08da9873dd9b20512a7fce01399c9d778e0ea652.camel@pschenker.ch>
On Thu, 06 Dec 2018 16:49:33 +0100
Philippe Schenker <dev@pschenker.ch> wrote:
> On Sun, 2018-11-25 at 10:04 +0000, Jonathan Cameron wrote:
> > On Fri, 23 Nov 2018 15:24:10 +0100
> > Philippe Schenker <dev@pschenker.ch> wrote:
> >
> > > From: Stefan Agner <stefan@agner.ch>
> > >
> > > This adds the devicetree bindings for the STMPE ADC.
> > >
> > > Signed-off-by: Stefan Agner <stefan@agner.ch>
> > > Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
> > > Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
> > Clearly this will need review from input and mfd.
> >
> > I've suggested inline that you split the realignment out to a
> > separate patch for reviewability reasons.
>
> Thank you again Jonathan for your feedback, and of course also all the others!
>
> I will split it much more so everything will be much more readable in v4. You
> suggested again, to use the naming 'adc {'. I know that this is standard naming,
> but unfortunately, this naming is given by drivers/mfd/stmpe.c (line 1311).
> What do you suggest to do? break the naming scheme in mfd, or just use
> 'stmpe_adc {' ?
Leave it as it is, but add a note ideally to say that is the reason.
Jonathan
>
> >
> > > ---
> > >
> > > Changes in v3:
> > > - Reformatted documentation for touchscreen to use tabs and have a better
> > > overview of the settings.
> > > - Added note which adc-settings will take precedence.
> > > - changed typo in sample-time setting from 144 clocks to 124 clocks, as
> > > stated
> > > in the datasheet.
> > >
> > > Changes in v2:
> > > - Moved the bindings for ADC to the overlying mfd.
> > > - Reformatted for better readability
> > >
> > > .../devicetree/bindings/iio/adc/stmpe-adc.txt | 21 +++++++
> > > .../bindings/input/touchscreen/stmpe.txt | 60 ++++++++++++-------
> > > .../devicetree/bindings/mfd/stmpe.txt | 28 ++++++---
> > > 3 files changed, 80 insertions(+), 29 deletions(-)
> > > create mode 100644 Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt
> > >
> > > diff --git a/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt
> > > b/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt
> > > new file mode 100644
> > > index 000000000000..480e66422625
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt
> > > @@ -0,0 +1,21 @@
> > > +STMPE ADC driver
> > > +----------------
> > > +
> > > +Required properties:
> > > + - compatible: "st,stmpe-adc"
> > > +
> > > +Optional properties:
> > > +Note that the ADC is shared with the STMPE touchscreen. ADC related
> > > settings
> > > +have to be done in the mfd.
> > > +- st,norequest-mask: bitmask specifying which ADC channels should _not_ be
> > > + requestable due to different usage (e.g. touch)
> > > +
> > > +Node name must be stmpe_adc and should be child node of stmpe node to
> > > +which it belongs.
> > > +
> > > +Example:
> > > +
> > > + stmpe_adc {
> >
> > Can we use adc { here to match standard naming?
> >
> > > + compatible = "st,stmpe-adc";
> > > + st,norequest-mask = <0x0F>; /* dont use ADC CH3-0 */
> > > + };
> > > diff --git a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
> > > b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
> > > index 127baa31a77a..414586513a02 100644
> > > --- a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
> > > +++ b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
> > > @@ -5,36 +5,52 @@ Required properties:
> > > - compatible: "st,stmpe-ts"
> > >
> > > Optional properties:
> > > -- st,sample-time: ADC converstion time in number of clock. (0 -> 36
> > > clocks, 1 ->
> > > - 44 clocks, 2 -> 56 clocks, 3 -> 64 clocks, 4 -> 80 clocks, 5 -> 96
> > > clocks, 6
> > > - -> 144 clocks), recommended is 4.
> > > -- st,mod-12b: ADC Bit mode (0 -> 10bit ADC, 1 -> 12bit ADC)
> > > -- st,ref-sel: ADC reference source (0 -> internal reference, 1 -> external
> > > - reference)
> > > -- st,adc-freq: ADC Clock speed (0 -> 1.625 MHz, 1 -> 3.25 MHz, 2 || 3 ->
> > > 6.5 MHz)
> > > -- st,ave-ctrl: Sample average control (0 -> 1 sample, 1 -> 2 samples, 2 ->
> > > 4
> > > - samples, 3 -> 8 samples)
> > > -- st,touch-det-delay: Touch detect interrupt delay (0 -> 10 us, 1 -> 50 us,
> > > 2 ->
> > > - 100 us, 3 -> 500 us, 4-> 1 ms, 5 -> 5 ms, 6 -> 10 ms, 7 -> 50 ms)
> > > recommended
> > > - is 3
> > > -- st,settling: Panel driver settling time (0 -> 10 us, 1 -> 100 us, 2 ->
> > > 500 us, 3
> > > - -> 1 ms, 4 -> 5 ms, 5 -> 10 ms, 6 for 50 ms, 7 -> 100 ms) recommended is
> > > 2
> > > -- st,fraction-z: Length of the fractional part in z (fraction-z ([0..7]) =
> > > Count of
> > > - the fractional part) recommended is 7
> > > -- st,i-drive: current limit value of the touchscreen drivers (0 -> 20 mA
> > > typical 35
> > > - mA max, 1 -> 50 mA typical 80 mA max)
> > > +- st,ave-ctrl : Sample average control
> > > + 0 -> 1 sample
> > > + 1 -> 2 samples
> > > + 2 -> 4 samples
> > > + 3 -> 8 samples
> > > +- st,touch-det-delay : Touch detect interrupt delay (recommended is
> > > 3)
> > > + 0 -> 10 us 5 -> 5 ms
> > > + 1 -> 50 us 6 -> 10 ms
> > > + 2 -> 100 us 7 -> 50 ms
> > > + 3 -> 500 us
> > > + 4-> 1 ms
> > > +- st,settling : Panel driver settling time (recommended is 2)
> > > + 0 -> 10 us 5 -> 10 ms
> > > + 1 -> 100 us 6 for 50 ms
> > > + 2 -> 500 us 7 -> 100 ms
> > > + 3 -> 1 ms
> > > + 4 -> 5 ms
> > > +- st,fraction-z : Length of the fractional part in z
> > > (recommended is 7)
> > > + (fraction-z ([0..7]) = Count of the fractional part)
> > > +- st,i-drive : current limit value of the touchscreen drivers
> > > + 0 -> 20 mA (typical 35mA max)
> > > + 1 -> 50 mA (typical 80 mA max)
> > > +
> > > +Optional properties common with MFD (deprecated):
> > > + - st,sample-time : ADC conversion time in number of clock.
> > > + 0 -> 36 clocks 4 -> 80 clocks
> > > (recommended)
> > > + 1 -> 44 clocks 5 -> 96 clocks
> > > + 2 -> 56 clocks 6 -> 124 clocks
> > > + 3 -> 64 clocks
> > > + - st,mod-12b : ADC Bit mode
> > > + 0 -> 10bit ADC 1 -> 12bit ADC
> > > + - st,ref-sel : ADC reference source
> > > + 0 -> internal 1 -> external
> > > + - st,adc-freq : ADC Clock speed
> > > + 0 -> 1.625 MHz 2 || 3 -> 6.5 MHz
> > > + 1 -> 3.25 MHz
> > >
> > > Node name must be stmpe_touchscreen and should be child node of stmpe node
> > > to
> > > which it belongs.
> > >
> > > +Note that common ADC settings of stmpe_touchscreen will take precedence.
> > > +
> > > Example:
> > >
> > > stmpe_touchscreen {
> > > compatible = "st,stmpe-ts";
> > > - st,sample-time = <4>;
> > > - st,mod-12b = <1>;
> > > - st,ref-sel = <0>;
> > > - st,adc-freq = <1>;
> > > st,ave-ctrl = <1>;
> > > st,touch-det-delay = <2>;
> > > st,settling = <2>;
> > > diff --git a/Documentation/devicetree/bindings/mfd/stmpe.txt
> > > b/Documentation/devicetree/bindings/mfd/stmpe.txt
> > > index c797c05cd3c2..d4408a417193 100644
> > > --- a/Documentation/devicetree/bindings/mfd/stmpe.txt
> > > +++ b/Documentation/devicetree/bindings/mfd/stmpe.txt
> > > @@ -4,15 +4,29 @@ STMPE is an MFD device which may expose the following
> > > inbuilt devices: gpio,
> > > keypad, touchscreen, adc, pwm, rotator.
> > >
> > > Required properties:
> > > - - compatible :
> > > "st,stmpe[610|801|811|1600|1601|2401|2403]"
> > > - - reg : I2C/SPI address of the device
> > > + - compatible :
> > > "st,stmpe[610|801|811|1600|1601|2401|2403]"
> > > + - reg : I2C/SPI address of the device
> >
> > Nothing wrong with correcting alignment, but it shouldn't be in the same patch
> > as a fundamental change lie this. Just adds noise.
> >
> > If that means you first have to introduce the new block missaligned, then
> > fix up the alignment in a follow up patch, then do that as we can then
> > effectively ignore the realignment as obviously correct and focus on
> > the real changes.
> >
> > >
> > > Optional properties:
> > > - - interrupts : The interrupt outputs from the controller
> > > - - interrupt-controller : Marks the device node as an interrupt
> > > controller
> > > - - wakeup-source : Marks the input device as wakable
> > > - - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128,
> > > 256, 512 and 1024
> > > - - irq-gpio : If present, which GPIO to use for event
> > > IRQ
> > > + - interrupts : The interrupt outputs from the
> > > controller
> > > + - interrupt-controller : Marks the device node as an interrupt
> > > controller
> > > + - wakeup-source : Marks the input device as wakable
> > > + - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64,
> > > 128, 256, 512 and 1024
> > > + - irq-gpio : If present, which GPIO to use for
> > > event IRQ
> > > +
> > > +Optional properties for devices with touch and ADC (STMPE811|STMPE610):
> > > + - st,sample-time : ADC conversion time in number of clock.
> > > + 0 -> 36 clocks 4 -> 80
> > > clocks (recommended)
> > > + 1 -> 44 clocks 5 -> 96
> > > clocks
> > > + 2 -> 56 clocks 6 -> 124
> > > clocks
> > > + 3 -> 64 clocks
> > > + - st,mod-12b : ADC Bit mode
> > > + 0 -> 10bit ADC 1 -> 12bit
> > > ADC
> > > + - st,ref-sel : ADC reference source
> > > + 0 -> internal 1 ->
> > > external
> > > + - st,adc-freq : ADC Clock speed
> > > + 0 -> 1.625 MHz 2 || 3 ->
> > > 6.5 MHz
> > > + 1 -> 3.25 MHz
> > >
> > > Example:
> > >
>
next prev parent reply other threads:[~2018-12-08 10:56 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-11-23 14:24 [PATCH v3 1/4] mfd: stmpe: Move ADC related defines to header of mfd Philippe Schenker
2018-11-23 14:24 ` [PATCH v3 2/4] iio: adc: add STMPE ADC driver using IIO framework Philippe Schenker
2018-11-25 10:27 ` Jonathan Cameron
2018-11-28 9:04 ` Lee Jones
2018-11-23 14:24 ` [PATCH v3 3/4] iio: adc: add STMPE ADC devicetree bindings Philippe Schenker
2018-11-25 10:04 ` Jonathan Cameron
2018-12-06 15:49 ` Philippe Schenker
2018-12-08 10:55 ` Jonathan Cameron [this message]
2018-11-28 9:02 ` Lee Jones
2018-11-23 14:24 ` [PATCH v3 4/4] ARM: dts: Add stmpe-adc driver to relevant devicetrees Philippe Schenker
2018-11-24 11:20 ` Dmitry Osipenko
2018-11-27 14:21 ` Thierry Reding
2018-11-28 9:15 ` [PATCH v3 1/4] mfd: stmpe: Move ADC related defines to header of mfd Lee Jones
2018-12-09 4:52 ` Dmitry Torokhov
2018-12-10 6:16 ` Lee Jones
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181208105553.61d51b7a@archlinux \
--to=jic23@kernel.org \
--cc=alexandre.torgue@st.com \
--cc=dev@pschenker.ch \
--cc=devicetree@vger.kernel.org \
--cc=dmitry.torokhov@gmail.com \
--cc=knaack.h@gmx.de \
--cc=lars@metafoo.de \
--cc=lee.jones@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-iio@vger.kernel.org \
--cc=linux-input@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-stm32@st-md-mailman.stormreply.com \
--cc=marcel.ziswiler@toradex.com \
--cc=mark.rutland@arm.com \
--cc=max.krummenacher@toradex.com \
--cc=mcoquelin.stm32@gmail.com \
--cc=pmeerw@pmeerw.net \
--cc=robh+dt@kernel.org \
--cc=stefan@agner.ch \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).