[PATCH v4 0/5] drm/bridge: various small lvds-encoder things

[PATCH v4 0/5] drm/bridge: various small lvds-encoder things

[Peter Rosin]

Hi!

I'm not sure if I should have added the texas chips to the lvds_encoder_match
list in the driver, right next to the thine,thc63lvdm83d entry, but ended
up not doing that. That can always be added later, if needed...

Changes since v3:
- retained a (modified) note in lvds-transmitter.txt about encoders with
  additional device-specific properties
- added tag from Rob on patch 3/5

Changes since v2:
- changed from pwdn-gpios to powerdown-gpios after discussion with Rob with
  new patch 3/5 updating the thine,thc63lvdm83d binding as well as a
  consequence
- added patch 4/5 which helps keep lines shorter in the lvds-encoder driver
- added tag from Rob on patch 2/5

Changes since v1:
- fork out the bindings for the texas chips into their own file in order
  to avoid clutter in the generic lvds-transmitter binding.
- added a patch to remove some surplus stuff in the generic lvds-transmitter
  binding.

Cheers,
Peter

Peter Rosin (5):
  dt-bindings: display: bridge: fork out ti,ds90c185 from
    lvds-transmitter
  dt-bindings: display: bridge: lvds-transmitter: cleanup example
  dt-bindings: display: bridge: thc63lvdm83d: use standard
    powerdown-gpios
  drm/bridge: lvds-encoder: add dev helper variable in .probe()
  drm/bridge: lvds-encoder: add powerdown-gpios support

 .../bindings/display/bridge/lvds-transmitter.txt   | 12 ++---
 .../bindings/display/bridge/thine,thc63lvdm83d.txt |  2 +-
 .../bindings/display/bridge/ti,ds90c185.txt        | 55 ++++++++++++++++++++++
 drivers/gpu/drm/bridge/lvds-encoder.c              | 53 +++++++++++++++++----
 4 files changed, 103 insertions(+), 19 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/display/bridge/ti,ds90c185.txt

-- 
2.11.0

[PATCH v4 1/5] dt-bindings: display: bridge: fork out ti,ds90c185 from lvds-transmitter

[Peter Rosin]

DS90C185 has a shutdown pin which does not fit in the lvds-transmitter
binding, which is meant to be generic.

The sister chip DS90C187 is similar to DS90C185, describe it here as well.

Signed-off-by: Peter Rosin <peda@axentia.se>
---
 .../bindings/display/bridge/lvds-transmitter.txt   | 10 ++--
 .../bindings/display/bridge/ti,ds90c185.txt        | 55 ++++++++++++++++++++++
 2 files changed, 59 insertions(+), 6 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/display/bridge/ti,ds90c185.txt

diff --git a/Documentation/devicetree/bindings/display/bridge/lvds-transmitter.txt b/Documentation/devicetree/bindings/display/bridge/lvds-transmitter.txt
index 50220190c203..bc6960741cb5 100644
--- a/Documentation/devicetree/bindings/display/bridge/lvds-transmitter.txt
+++ b/Documentation/devicetree/bindings/display/bridge/lvds-transmitter.txt
@@ -22,13 +22,11 @@ among others.
 
 Required properties:
 
-- compatible: Must be one or more of the following
-  - "ti,ds90c185" for the TI DS90C185 FPD-Link Serializer
-  - "lvds-encoder" for a generic LVDS encoder device
+- compatible: Must be "lvds-encoder"
 
-  When compatible with the generic version, nodes must list the
-  device-specific version corresponding to the device first
-  followed by the generic version.
+  Any encoder compatible with this generic binding, but with additional
+  properties not listed here, must list a device specific compatible first
+  followed by this generic compatible.
 
 Required nodes:
 
diff --git a/Documentation/devicetree/bindings/display/bridge/ti,ds90c185.txt b/Documentation/devicetree/bindings/display/bridge/ti,ds90c185.txt
new file mode 100644
index 000000000000..e575f996959a
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/bridge/ti,ds90c185.txt
@@ -0,0 +1,55 @@
+Texas Instruments FPD-Link (LVDS) Serializer
+--------------------------------------------
+
+The DS90C185 and DS90C187 are low-power serializers for portable
+battery-powered applications that reduces the size of the RGB
+interface between the host GPU and the display.
+
+Required properties:
+
+- compatible: Should be
+  "ti,ds90c185", "lvds-encoder"  for the TI DS90C185 FPD-Link Serializer
+  "ti,ds90c187", "lvds-encoder"  for the TI DS90C187 FPD-Link Serializer
+
+Optional properties:
+
+- powerdown-gpios: Power down control GPIO (the PDB pin, active-low)
+
+Required nodes:
+
+The devices have two video ports. Their connections are modeled using the OF
+graph bindings specified in Documentation/devicetree/bindings/graph.txt.
+
+- Video port 0 for parallel input
+- Video port 1 for LVDS output
+
+
+Example
+-------
+
+lvds-encoder {
+	compatible = "ti,ds90c185", "lvds-encoder";
+
+	powerdown-gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			lvds_enc_in: endpoint {
+				remote-endpoint = <&lcdc_out_rgb>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			lvds_enc_out: endpoint {
+				remote-endpoint = <&lvds_panel_in>;
+			};
+		};
+	};
+};
-- 
2.11.0

[PATCH v4 2/5] dt-bindings: display: bridge: lvds-transmitter: cleanup example

[Peter Rosin]

Drop #address-cells and #size-cells from the root node in the
example, they are unused.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Rosin <peda@axentia.se>
---
 Documentation/devicetree/bindings/display/bridge/lvds-transmitter.txt | 2 --
 1 file changed, 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/display/bridge/lvds-transmitter.txt b/Documentation/devicetree/bindings/display/bridge/lvds-transmitter.txt
index bc6960741cb5..60091db5dfa5 100644
--- a/Documentation/devicetree/bindings/display/bridge/lvds-transmitter.txt
+++ b/Documentation/devicetree/bindings/display/bridge/lvds-transmitter.txt
@@ -42,8 +42,6 @@ Example
 
 lvds-encoder {
 	compatible = "lvds-encoder";
-	#address-cells = <1>;
-	#size-cells = <0>;
 
 	ports {
 		#address-cells = <1>;
-- 
2.11.0

[PATCH v4 3/5] dt-bindings: display: bridge: thc63lvdm83d: use standard powerdown-gpios

[Peter Rosin]

The name powerdown-gpios is the standard property name for the
functionality covered by the previous pwdn-gpios name. This rename
should be safe to do since the linux driver supporting the binding
(lvds-encoder.c) never implemented the property, and no dts file
names it. At least not upstream.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Rosin <peda@axentia.se>
---
 Documentation/devicetree/bindings/display/bridge/thine,thc63lvdm83d.txt | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/display/bridge/thine,thc63lvdm83d.txt b/Documentation/devicetree/bindings/display/bridge/thine,thc63lvdm83d.txt
index 527e236e9a2a..fee3c88e1a17 100644
--- a/Documentation/devicetree/bindings/display/bridge/thine,thc63lvdm83d.txt
+++ b/Documentation/devicetree/bindings/display/bridge/thine,thc63lvdm83d.txt
@@ -10,7 +10,7 @@ Required properties:
 
 Optional properties:
 
-- pwdn-gpios: Power down control GPIO
+- powerdown-gpios: Power down control GPIO (the /PWDN pin, active low).
 
 Required nodes:
 
-- 
2.11.0

[PATCH v4 4/5] drm/bridge: lvds-encoder: add dev helper variable in .probe()

[Peter Rosin]

Make the code easier to read and modify.

Signed-off-by: Peter Rosin <peda@axentia.se>
---
 drivers/gpu/drm/bridge/lvds-encoder.c | 19 +++++++++----------
 1 file changed, 9 insertions(+), 10 deletions(-)

diff --git a/drivers/gpu/drm/bridge/lvds-encoder.c b/drivers/gpu/drm/bridge/lvds-encoder.c
index 75b0d3f6e4de..f6770e83d49d 100644
--- a/drivers/gpu/drm/bridge/lvds-encoder.c
+++ b/drivers/gpu/drm/bridge/lvds-encoder.c
@@ -34,48 +34,47 @@ static struct drm_bridge_funcs funcs = {
 
 static int lvds_encoder_probe(struct platform_device *pdev)
 {
+	struct device *dev = &pdev->dev;
 	struct device_node *port;
 	struct device_node *endpoint;
 	struct device_node *panel_node;
 	struct drm_panel *panel;
 	struct lvds_encoder *lvds_encoder;
 
-	lvds_encoder = devm_kzalloc(&pdev->dev, sizeof(*lvds_encoder),
-				    GFP_KERNEL);
+	lvds_encoder = devm_kzalloc(dev, sizeof(*lvds_encoder), GFP_KERNEL);
 	if (!lvds_encoder)
 		return -ENOMEM;
 
 	/* Locate the panel DT node. */
-	port = of_graph_get_port_by_id(pdev->dev.of_node, 1);
+	port = of_graph_get_port_by_id(dev->of_node, 1);
 	if (!port) {
-		dev_dbg(&pdev->dev, "port 1 not found\n");
+		dev_dbg(dev, "port 1 not found\n");
 		return -ENXIO;
 	}
 
 	endpoint = of_get_child_by_name(port, "endpoint");
 	of_node_put(port);
 	if (!endpoint) {
-		dev_dbg(&pdev->dev, "no endpoint for port 1\n");
+		dev_dbg(dev, "no endpoint for port 1\n");
 		return -ENXIO;
 	}
 
 	panel_node = of_graph_get_remote_port_parent(endpoint);
 	of_node_put(endpoint);
 	if (!panel_node) {
-		dev_dbg(&pdev->dev, "no remote endpoint for port 1\n");
+		dev_dbg(dev, "no remote endpoint for port 1\n");
 		return -ENXIO;
 	}
 
 	panel = of_drm_find_panel(panel_node);
 	of_node_put(panel_node);
 	if (!panel) {
-		dev_dbg(&pdev->dev, "panel not found, deferring probe\n");
+		dev_dbg(dev, "panel not found, deferring probe\n");
 		return -EPROBE_DEFER;
 	}
 
 	lvds_encoder->panel_bridge =
-		devm_drm_panel_bridge_add(&pdev->dev,
-					  panel, DRM_MODE_CONNECTOR_LVDS);
+		devm_drm_panel_bridge_add(dev, panel, DRM_MODE_CONNECTOR_LVDS);
 	if (IS_ERR(lvds_encoder->panel_bridge))
 		return PTR_ERR(lvds_encoder->panel_bridge);
 
@@ -83,7 +82,7 @@ static int lvds_encoder_probe(struct platform_device *pdev)
 	 * but we need a bridge attached to our of_node for our user
 	 * to look up.
 	 */
-	lvds_encoder->bridge.of_node = pdev->dev.of_node;
+	lvds_encoder->bridge.of_node = dev->of_node;
 	lvds_encoder->bridge.funcs = &funcs;
 	drm_bridge_add(&lvds_encoder->bridge);
 
-- 
2.11.0

[PATCH v4 5/5] drm/bridge: lvds-encoder: add powerdown-gpios support

[Peter Rosin]

Optionally power down the LVDS-encoder when it is not in use.

Signed-off-by: Peter Rosin <peda@axentia.se>
---
 drivers/gpu/drm/bridge/lvds-encoder.c | 34 ++++++++++++++++++++++++++++++++++
 1 file changed, 34 insertions(+)

diff --git a/drivers/gpu/drm/bridge/lvds-encoder.c b/drivers/gpu/drm/bridge/lvds-encoder.c
index f6770e83d49d..36d8557bc097 100644
--- a/drivers/gpu/drm/bridge/lvds-encoder.c
+++ b/drivers/gpu/drm/bridge/lvds-encoder.c
@@ -11,11 +11,13 @@
 #include <drm/drm_bridge.h>
 #include <drm/drm_panel.h>
 
+#include <linux/gpio/consumer.h>
 #include <linux/of_graph.h>
 
 struct lvds_encoder {
 	struct drm_bridge bridge;
 	struct drm_bridge *panel_bridge;
+	struct gpio_desc *powerdown_gpio;
 };
 
 static int lvds_encoder_attach(struct drm_bridge *bridge)
@@ -28,8 +30,30 @@ static int lvds_encoder_attach(struct drm_bridge *bridge)
 				 bridge);
 }
 
+static void lvds_encoder_enable(struct drm_bridge *bridge)
+{
+	struct lvds_encoder *lvds_encoder = container_of(bridge,
+							 struct lvds_encoder,
+							 bridge);
+
+	if (lvds_encoder->powerdown_gpio)
+		gpiod_set_value_cansleep(lvds_encoder->powerdown_gpio, 0);
+}
+
+static void lvds_encoder_disable(struct drm_bridge *bridge)
+{
+	struct lvds_encoder *lvds_encoder = container_of(bridge,
+							 struct lvds_encoder,
+							 bridge);
+
+	if (lvds_encoder->powerdown_gpio)
+		gpiod_set_value_cansleep(lvds_encoder->powerdown_gpio, 1);
+}
+
 static struct drm_bridge_funcs funcs = {
 	.attach = lvds_encoder_attach,
+	.enable = lvds_encoder_enable,
+	.disable = lvds_encoder_disable,
 };
 
 static int lvds_encoder_probe(struct platform_device *pdev)
@@ -45,6 +69,16 @@ static int lvds_encoder_probe(struct platform_device *pdev)
 	if (!lvds_encoder)
 		return -ENOMEM;
 
+	lvds_encoder->powerdown_gpio = devm_gpiod_get_optional(dev, "powerdown",
+							       GPIOD_OUT_HIGH);
+	if (IS_ERR(lvds_encoder->powerdown_gpio)) {
+		int err = PTR_ERR(lvds_encoder->powerdown_gpio);
+
+		if (err != -EPROBE_DEFER)
+			dev_err(dev, "powerdown GPIO failure: %d\n", err);
+		return err;
+	}
+
 	/* Locate the panel DT node. */
 	port = of_graph_get_port_by_id(dev->of_node, 1);
 	if (!port) {
-- 
2.11.0

Re: [PATCH v4 1/5] dt-bindings: display: bridge: fork out ti,ds90c185 from lvds-transmitter

[Rob Herring]

On Fri, 11 Jan 2019 15:18:55 +0000, Peter Rosin wrote:
> DS90C185 has a shutdown pin which does not fit in the lvds-transmitter
> binding, which is meant to be generic.
> 
> The sister chip DS90C187 is similar to DS90C185, describe it here as well.
> 
> Signed-off-by: Peter Rosin <peda@axentia.se>
> ---
>  .../bindings/display/bridge/lvds-transmitter.txt   | 10 ++--
>  .../bindings/display/bridge/ti,ds90c185.txt        | 55 ++++++++++++++++++++++
>  2 files changed, 59 insertions(+), 6 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/display/bridge/ti,ds90c185.txt
> 

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH v4 4/5] drm/bridge: lvds-encoder: add dev helper variable in .probe()

[Andrzej Hajda]

On 11.01.2019 16:19, Peter Rosin wrote:
> Make the code easier to read and modify.
>
> Signed-off-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>

 --
Regards
Andrzej

Re: [PATCH v4 5/5] drm/bridge: lvds-encoder: add powerdown-gpios support

[Andrzej Hajda]

On 11.01.2019 16:19, Peter Rosin wrote:
> Optionally power down the LVDS-encoder when it is not in use.
>
> Signed-off-by: Peter Rosin <peda@axentia.se>


Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>


 --
Regards
Andrzej

Re: [PATCH v4 0/5] drm/bridge: various small lvds-encoder things

[Andrzej Hajda]

On 11.01.2019 16:18, Peter Rosin wrote:
> Hi!
>
> I'm not sure if I should have added the texas chips to the lvds_encoder_match
> list in the driver, right next to the thine,thc63lvdm83d entry, but ended
> up not doing that. That can always be added later, if needed...
>
> Changes since v3:
> - retained a (modified) note in lvds-transmitter.txt about encoders with
>   additional device-specific properties
> - added tag from Rob on patch 3/5
>
> Changes since v2:
> - changed from pwdn-gpios to powerdown-gpios after discussion with Rob with
>   new patch 3/5 updating the thine,thc63lvdm83d binding as well as a
>   consequence
> - added patch 4/5 which helps keep lines shorter in the lvds-encoder driver
> - added tag from Rob on patch 2/5
>
> Changes since v1:
> - fork out the bindings for the texas chips into their own file in order
>   to avoid clutter in the generic lvds-transmitter binding.
> - added a patch to remove some surplus stuff in the generic lvds-transmitter
>   binding.
>
> Cheers,
> Peter


Queued to drm-misc-next.


One thing I have spotted after merging is that there no need to
null-check before gpiod_set_value_cansleep, no big deal, I guess.


Regards

Andrzej


>
> Peter Rosin (5):
>   dt-bindings: display: bridge: fork out ti,ds90c185 from
>     lvds-transmitter
>   dt-bindings: display: bridge: lvds-transmitter: cleanup example
>   dt-bindings: display: bridge: thc63lvdm83d: use standard
>     powerdown-gpios
>   drm/bridge: lvds-encoder: add dev helper variable in .probe()
>   drm/bridge: lvds-encoder: add powerdown-gpios support
>
>  .../bindings/display/bridge/lvds-transmitter.txt   | 12 ++---
>  .../bindings/display/bridge/thine,thc63lvdm83d.txt |  2 +-
>  .../bindings/display/bridge/ti,ds90c185.txt        | 55 ++++++++++++++++++++++
>  drivers/gpu/drm/bridge/lvds-encoder.c              | 53 +++++++++++++++++----
>  4 files changed, 103 insertions(+), 19 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/display/bridge/ti,ds90c185.txt
>

[PATCH] drm/bridge: lvds-encoder: remove surplus NULL checks

[Peter Rosin]

The gpio API explicitly allows skipping the NULL check, precisely to
allow for neat support for optional gpios. Which is exactly what is at
play here.

Reported-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
---
 drivers/gpu/drm/bridge/lvds-encoder.c | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)

diff --git a/drivers/gpu/drm/bridge/lvds-encoder.c b/drivers/gpu/drm/bridge/lvds-encoder.c
index 36d8557bc097..584007eaf6e1 100644
--- a/drivers/gpu/drm/bridge/lvds-encoder.c
+++ b/drivers/gpu/drm/bridge/lvds-encoder.c
@@ -36,8 +36,7 @@ static void lvds_encoder_enable(struct drm_bridge *bridge)
 							 struct lvds_encoder,
 							 bridge);
 
-	if (lvds_encoder->powerdown_gpio)
-		gpiod_set_value_cansleep(lvds_encoder->powerdown_gpio, 0);
+	gpiod_set_value_cansleep(lvds_encoder->powerdown_gpio, 0);
 }
 
 static void lvds_encoder_disable(struct drm_bridge *bridge)
@@ -46,8 +45,7 @@ static void lvds_encoder_disable(struct drm_bridge *bridge)
 							 struct lvds_encoder,
 							 bridge);
 
-	if (lvds_encoder->powerdown_gpio)
-		gpiod_set_value_cansleep(lvds_encoder->powerdown_gpio, 1);
+	gpiod_set_value_cansleep(lvds_encoder->powerdown_gpio, 1);
 }
 
 static struct drm_bridge_funcs funcs = {
-- 
2.11.0

Re: [PATCH] drm/bridge: lvds-encoder: remove surplus NULL checks

[Daniel Vetter]

On Fri, Jan 18, 2019 at 11:11:38PM +0000, Peter Rosin wrote:
> The gpio API explicitly allows skipping the NULL check, precisely to
> allow for neat support for optional gpios. Which is exactly what is at
> play here.
> 
> Reported-by: Andrzej Hajda <a.hajda@samsung.com>
> Signed-off-by: Peter Rosin <peda@axentia.se>

lgtm, Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>

btw plan to stick around a bit in drm land, i.e. want commit rights for
drm-misc?
-Daniel

> ---
>  drivers/gpu/drm/bridge/lvds-encoder.c | 6 ++----
>  1 file changed, 2 insertions(+), 4 deletions(-)
> 
> diff --git a/drivers/gpu/drm/bridge/lvds-encoder.c b/drivers/gpu/drm/bridge/lvds-encoder.c
> index 36d8557bc097..584007eaf6e1 100644
> --- a/drivers/gpu/drm/bridge/lvds-encoder.c
> +++ b/drivers/gpu/drm/bridge/lvds-encoder.c
> @@ -36,8 +36,7 @@ static void lvds_encoder_enable(struct drm_bridge *bridge)
>  							 struct lvds_encoder,
>  							 bridge);
>  
> -	if (lvds_encoder->powerdown_gpio)
> -		gpiod_set_value_cansleep(lvds_encoder->powerdown_gpio, 0);
> +	gpiod_set_value_cansleep(lvds_encoder->powerdown_gpio, 0);
>  }
>  
>  static void lvds_encoder_disable(struct drm_bridge *bridge)
> @@ -46,8 +45,7 @@ static void lvds_encoder_disable(struct drm_bridge *bridge)
>  							 struct lvds_encoder,
>  							 bridge);
>  
> -	if (lvds_encoder->powerdown_gpio)
> -		gpiod_set_value_cansleep(lvds_encoder->powerdown_gpio, 1);
> +	gpiod_set_value_cansleep(lvds_encoder->powerdown_gpio, 1);
>  }
>  
>  static struct drm_bridge_funcs funcs = {
> -- 
> 2.11.0
> 
> _______________________________________________
> dri-devel mailing list
> dri-devel@lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/dri-devel

-- 
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch

Re: [PATCH] drm/bridge: lvds-encoder: remove surplus NULL checks

[Laurent Pinchart]

Hi Peter,

Thank you for the patch.

On Fri, Jan 18, 2019 at 11:11:38PM +0000, Peter Rosin wrote:
> The gpio API explicitly allows skipping the NULL check, precisely to
> allow for neat support for optional gpios. Which is exactly what is at
> play here.
> 
> Reported-by: Andrzej Hajda <a.hajda@samsung.com>
> Signed-off-by: Peter Rosin <peda@axentia.se>

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

> ---
>  drivers/gpu/drm/bridge/lvds-encoder.c | 6 ++----
>  1 file changed, 2 insertions(+), 4 deletions(-)
> 
> diff --git a/drivers/gpu/drm/bridge/lvds-encoder.c b/drivers/gpu/drm/bridge/lvds-encoder.c
> index 36d8557bc097..584007eaf6e1 100644
> --- a/drivers/gpu/drm/bridge/lvds-encoder.c
> +++ b/drivers/gpu/drm/bridge/lvds-encoder.c
> @@ -36,8 +36,7 @@ static void lvds_encoder_enable(struct drm_bridge *bridge)
>  							 struct lvds_encoder,
>  							 bridge);
>  
> -	if (lvds_encoder->powerdown_gpio)
> -		gpiod_set_value_cansleep(lvds_encoder->powerdown_gpio, 0);
> +	gpiod_set_value_cansleep(lvds_encoder->powerdown_gpio, 0);
>  }
>  
>  static void lvds_encoder_disable(struct drm_bridge *bridge)
> @@ -46,8 +45,7 @@ static void lvds_encoder_disable(struct drm_bridge *bridge)
>  							 struct lvds_encoder,
>  							 bridge);
>  
> -	if (lvds_encoder->powerdown_gpio)
> -		gpiod_set_value_cansleep(lvds_encoder->powerdown_gpio, 1);
> +	gpiod_set_value_cansleep(lvds_encoder->powerdown_gpio, 1);
>  }
>  
>  static struct drm_bridge_funcs funcs = {

-- 
Regards,

Laurent Pinchart