[PATCH v11 2/3] Bluetooth: hci_qca: Deassert RTS while baudrate change command

[Balakrishna Godavarthi <bgodavar@codeaurora.org>]

This patch will help to stop frame reassembly errors while changing
the baudrate. This is because host send a change baudrate request
command to the chip with 115200 bps, Whereas chip will change their
UART clocks to the enable for new baudrate and sends the response
for the change request command with newer baudrate, On host side
we are still operating in 115200 bps which results of reading garbage
data. Here we are pulling RTS line, so that chip we will wait to send data
to host until host change its baudrate.

Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
---
Changes in v10:
Enabled flow control back when the baudarte change request fails.
---
 drivers/bluetooth/hci_qca.c | 29 +++++++++++++++--------------
 1 file changed, 15 insertions(+), 14 deletions(-)

diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
index 9a1c0a71b460..e3cf0dbfc89d 100644
--- a/drivers/bluetooth/hci_qca.c
+++ b/drivers/bluetooth/hci_qca.c
@@ -964,7 +964,6 @@ static int qca_set_baudrate(struct hci_dev *hdev, uint8_t baudrate)
 	struct hci_uart *hu = hci_get_drvdata(hdev);
 	struct qca_data *qca = hu->priv;
 	struct sk_buff *skb;
-	struct qca_serdev *qcadev;
 	u8 cmd[] = { 0x01, 0x48, 0xFC, 0x01, 0x00 };
 
 	if (baudrate > QCA_BAUDRATE_3200000)
@@ -978,13 +977,6 @@ static int qca_set_baudrate(struct hci_dev *hdev, uint8_t baudrate)
 		return -ENOMEM;
 	}
 
-	/* Disabling hardware flow control is mandatory while
-	 * sending change baudrate request to wcn3990 SoC.
-	 */
-	qcadev = serdev_device_get_drvdata(hu->serdev);
-	if (qcadev->btsoc_type == QCA_WCN3990)
-		hci_uart_set_flow_control(hu, true);
-
 	/* Assign commands to change baudrate and packet type. */
 	skb_put_data(skb, cmd, sizeof(cmd));
 	hci_skb_pkt_type(skb) = HCI_COMMAND_PKT;
@@ -1000,9 +992,6 @@ static int qca_set_baudrate(struct hci_dev *hdev, uint8_t baudrate)
 	schedule_timeout(msecs_to_jiffies(BAUDRATE_SETTLE_TIMEOUT_MS));
 	set_current_state(TASK_RUNNING);
 
-	if (qcadev->btsoc_type == QCA_WCN3990)
-		hci_uart_set_flow_control(hu, false);
-
 	return 0;
 }
 
@@ -1089,7 +1078,8 @@ static int qca_check_speeds(struct hci_uart *hu)
 static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)
 {
 	unsigned int speed, qca_baudrate;
-	int ret;
+	struct qca_serdev *qcadev;
+	int ret = 0;
 
 	if (speed_type == QCA_INIT_SPEED) {
 		speed = qca_get_speed(hu, QCA_INIT_SPEED);
@@ -1100,16 +1090,27 @@ static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)
 		if (!speed)
 			return 0;
 
+		/* Disable flow control for wcn3990 to deassert RTS while
+		 * changing the baudrate of chip and host.
+		 */
+		qcadev = serdev_device_get_drvdata(hu->serdev);
+		if (qcadev->btsoc_type == QCA_WCN3990)
+			hci_uart_set_flow_control(hu, true);
+
 		qca_baudrate = qca_get_baudrate_value(speed);
 		bt_dev_dbg(hu->hdev, "Set UART speed to %d", speed);
 		ret = qca_set_baudrate(hu->hdev, qca_baudrate);
 		if (ret)
-			return ret;
+			goto error;
 
 		host_set_baudrate(hu, speed);
+
+error:
+		if (qcadev->btsoc_type == QCA_WCN3990)
+			hci_uart_set_flow_control(hu, false);
 	}
 
-	return 0;
+	return ret;
 }
 
 static int qca_wcn3990_init(struct hci_uart *hu)
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project