linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Daniel Lezcano <daniel.lezcano@linaro.org>
To: tglx@linutronix.de
Cc: linux-kernel@vger.kernel.org,
	Samuel Holland <samuel@sholland.org>,
	stable@vger.kernel.org, Maxime Ripard <maxime.ripard@bootlin.com>,
	Andre Przywara <andre.przywara@arm.com>,
	Catalin Marinas <catalin.marinas@arm.com>,
	Will Deacon <will.deacon@arm.com>,
	Jonathan Corbet <corbet@lwn.net>,
	Mark Rutland <mark.rutland@arm.com>,
	Marc Zyngier <marc.zyngier@arm.com>,
	linux-arm-kernel@lists.infradead.org (moderated list:ARM64 PORT
	(AARCH64 ARCHITECTURE)),
	linux-doc@vger.kernel.org (open list:DOCUMENTATION)
Subject: [PATCH 02/18] clocksource/drivers/arch_timer: Workaround for Allwinner A64 timer instability
Date: Sat, 23 Feb 2019 14:06:50 +0100	[thread overview]
Message-ID: <20190223130707.16704-2-daniel.lezcano@linaro.org> (raw)
In-Reply-To: <20190223130707.16704-1-daniel.lezcano@linaro.org>

From: Samuel Holland <samuel@sholland.org>

The Allwinner A64 SoC is known[1] to have an unstable architectural
timer, which manifests itself most obviously in the time jumping forward
a multiple of 95 years[2][3]. This coincides with 2^56 cycles at a
timer frequency of 24 MHz, implying that the time went slightly backward
(and this was interpreted by the kernel as it jumping forward and
wrapping around past the epoch).

Investigation revealed instability in the low bits of CNTVCT at the
point a high bit rolls over. This leads to power-of-two cycle forward
and backward jumps. (Testing shows that forward jumps are about twice as
likely as backward jumps.) Since the counter value returns to normal
after an indeterminate read, each "jump" really consists of both a
forward and backward jump from the software perspective.

Unless the kernel is trapping CNTVCT reads, a userspace program is able
to read the register in a loop faster than it changes. A test program
running on all 4 CPU cores that reported jumps larger than 100 ms was
run for 13.6 hours and reported the following:

 Count | Event
-------+---------------------------
  9940 | jumped backward      699ms
   268 | jumped backward     1398ms
     1 | jumped backward     2097ms
 16020 | jumped forward       175ms
  6443 | jumped forward       699ms
  2976 | jumped forward      1398ms
     9 | jumped forward    356516ms
     9 | jumped forward    357215ms
     4 | jumped forward    714430ms
     1 | jumped forward   3578440ms

This works out to a jump larger than 100 ms about every 5.5 seconds on
each CPU core.

The largest jump (almost an hour!) was the following sequence of reads:
    0x0000007fffffffff → 0x00000093feffffff → 0x0000008000000000

Note that the middle bits don't necessarily all read as all zeroes or
all ones during the anomalous behavior; however the low 10 bits checked
by the function in this patch have never been observed with any other
value.

Also note that smaller jumps are much more common, with backward jumps
of 2048 (2^11) cycles observed over 400 times per second on each core.
(Of course, this is partially explained by lower bits rolling over more
frequently.) Any one of these could have caused the 95 year time skip.

Similar anomalies were observed while reading CNTPCT (after patching the
kernel to allow reads from userspace). However, the CNTPCT jumps are
much less frequent, and only small jumps were observed. The same program
as before (except now reading CNTPCT) observed after 72 hours:

 Count | Event
-------+---------------------------
    17 | jumped backward      699ms
    52 | jumped forward       175ms
  2831 | jumped forward       699ms
     5 | jumped forward      1398ms

Further investigation showed that the instability in CNTPCT/CNTVCT also
affected the respective timer's TVAL register. The following values were
observed immediately after writing CNVT_TVAL to 0x10000000:

 CNTVCT             | CNTV_TVAL  | CNTV_CVAL          | CNTV_TVAL Error
--------------------+------------+--------------------+-----------------
 0x000000d4a2d8bfff | 0x10003fff | 0x000000d4b2d8bfff | +0x00004000
 0x000000d4a2d94000 | 0x0fffffff | 0x000000d4b2d97fff | -0x00004000
 0x000000d4a2d97fff | 0x10003fff | 0x000000d4b2d97fff | +0x00004000
 0x000000d4a2d9c000 | 0x0fffffff | 0x000000d4b2d9ffff | -0x00004000

The pattern of errors in CNTV_TVAL seemed to depend on exactly which
value was written to it. For example, after writing 0x10101010:

 CNTVCT             | CNTV_TVAL  | CNTV_CVAL          | CNTV_TVAL Error
--------------------+------------+--------------------+-----------------
 0x000001ac3effffff | 0x1110100f | 0x000001ac4f10100f | +0x1000000
 0x000001ac40000000 | 0x1010100f | 0x000001ac5110100f | -0x1000000
 0x000001ac58ffffff | 0x1110100f | 0x000001ac6910100f | +0x1000000
 0x000001ac66000000 | 0x1010100f | 0x000001ac7710100f | -0x1000000
 0x000001ac6affffff | 0x1110100f | 0x000001ac7b10100f | +0x1000000
 0x000001ac6e000000 | 0x1010100f | 0x000001ac7f10100f | -0x1000000

I was also twice able to reproduce the issue covered by Allwinner's
workaround[4], that writing to TVAL sometimes fails, and both CVAL and
TVAL are left with entirely bogus values. One was the following values:

 CNTVCT             | CNTV_TVAL  | CNTV_CVAL
--------------------+------------+--------------------------------------
 0x000000d4a2d6014c | 0x8fbd5721 | 0x000000d132935fff (615s in the past)
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>

========================================================================

Because the CPU can read the CNTPCT/CNTVCT registers faster than they
change, performing two reads of the register and comparing the high bits
(like other workarounds) is not a workable solution. And because the
timer can jump both forward and backward, no pair of reads can
distinguish a good value from a bad one. The only way to guarantee a
good value from consecutive reads would be to read _three_ times, and
take the middle value only if the three values are 1) each unique and
2) increasing. This takes at minimum 3 counter cycles (125 ns), or more
if an anomaly is detected.

However, since there is a distinct pattern to the bad values, we can
optimize the common case (1022/1024 of the time) to a single read by
simply ignoring values that match the error pattern. This still takes no
more than 3 cycles in the worst case, and requires much less code. As an
additional safety check, we still limit the loop iteration to the number
of max-frequency (1.2 GHz) CPU cycles in three 24 MHz counter periods.

For the TVAL registers, the simple solution is to not use them. Instead,
read or write the CVAL and calculate the TVAL value in software.

Although the manufacturer is aware of at least part of the erratum[4],
there is no official name for it. For now, use the kernel-internal name
"UNKNOWN1".

[1]: https://github.com/armbian/build/commit/a08cd6fe7ae9
[2]: https://forum.armbian.com/topic/3458-a64-datetime-clock-issue/
[3]: https://irclog.whitequark.org/linux-sunxi/2018-01-26
[4]: https://github.com/Allwinner-Homlet/H6-BSP4.9-linux/blob/master/drivers/clocksource/arm_arch_timer.c#L272

Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
---
 Documentation/arm64/silicon-errata.txt |  2 +
 drivers/clocksource/Kconfig            | 10 +++++
 drivers/clocksource/arm_arch_timer.c   | 55 ++++++++++++++++++++++++++
 3 files changed, 67 insertions(+)

diff --git a/Documentation/arm64/silicon-errata.txt b/Documentation/arm64/silicon-errata.txt
index 1f09d043d086..ddb8ce5333ba 100644
--- a/Documentation/arm64/silicon-errata.txt
+++ b/Documentation/arm64/silicon-errata.txt
@@ -44,6 +44,8 @@ stable kernels.
 
 | Implementor    | Component       | Erratum ID      | Kconfig                     |
 +----------------+-----------------+-----------------+-----------------------------+
+| Allwinner      | A64/R18         | UNKNOWN1        | SUN50I_ERRATUM_UNKNOWN1     |
+|                |                 |                 |                             |
 | ARM            | Cortex-A53      | #826319         | ARM64_ERRATUM_826319        |
 | ARM            | Cortex-A53      | #827319         | ARM64_ERRATUM_827319        |
 | ARM            | Cortex-A53      | #824069         | ARM64_ERRATUM_824069        |
diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
index a9e26f6a81a1..8dfd3bc448d0 100644
--- a/drivers/clocksource/Kconfig
+++ b/drivers/clocksource/Kconfig
@@ -360,6 +360,16 @@ config ARM64_ERRATUM_858921
 	  The workaround will be dynamically enabled when an affected
 	  core is detected.
 
+config SUN50I_ERRATUM_UNKNOWN1
+	bool "Workaround for Allwinner A64 erratum UNKNOWN1"
+	default y
+	depends on ARM_ARCH_TIMER && ARM64 && ARCH_SUNXI
+	select ARM_ARCH_TIMER_OOL_WORKAROUND
+	help
+	  This option enables a workaround for instability in the timer on
+	  the Allwinner A64 SoC. The workaround will only be active if the
+	  allwinner,erratum-unknown1 property is found in the timer node.
+
 config ARM_GLOBAL_TIMER
 	bool "Support for the ARM global timer" if COMPILE_TEST
 	select TIMER_OF if OF
diff --git a/drivers/clocksource/arm_arch_timer.c b/drivers/clocksource/arm_arch_timer.c
index 9a7d4dc00b6e..a8b20b65bd4b 100644
--- a/drivers/clocksource/arm_arch_timer.c
+++ b/drivers/clocksource/arm_arch_timer.c
@@ -326,6 +326,48 @@ static u64 notrace arm64_1188873_read_cntvct_el0(void)
 }
 #endif
 
+#ifdef CONFIG_SUN50I_ERRATUM_UNKNOWN1
+/*
+ * The low bits of the counter registers are indeterminate while bit 10 or
+ * greater is rolling over. Since the counter value can jump both backward
+ * (7ff -> 000 -> 800) and forward (7ff -> fff -> 800), ignore register values
+ * with all ones or all zeros in the low bits. Bound the loop by the maximum
+ * number of CPU cycles in 3 consecutive 24 MHz counter periods.
+ */
+#define __sun50i_a64_read_reg(reg) ({					\
+	u64 _val;							\
+	int _retries = 150;						\
+									\
+	do {								\
+		_val = read_sysreg(reg);				\
+		_retries--;						\
+	} while (((_val + 1) & GENMASK(9, 0)) <= 1 && _retries);	\
+									\
+	WARN_ON_ONCE(!_retries);					\
+	_val;								\
+})
+
+static u64 notrace sun50i_a64_read_cntpct_el0(void)
+{
+	return __sun50i_a64_read_reg(cntpct_el0);
+}
+
+static u64 notrace sun50i_a64_read_cntvct_el0(void)
+{
+	return __sun50i_a64_read_reg(cntvct_el0);
+}
+
+static u32 notrace sun50i_a64_read_cntp_tval_el0(void)
+{
+	return read_sysreg(cntp_cval_el0) - sun50i_a64_read_cntpct_el0();
+}
+
+static u32 notrace sun50i_a64_read_cntv_tval_el0(void)
+{
+	return read_sysreg(cntv_cval_el0) - sun50i_a64_read_cntvct_el0();
+}
+#endif
+
 #ifdef CONFIG_ARM_ARCH_TIMER_OOL_WORKAROUND
 DEFINE_PER_CPU(const struct arch_timer_erratum_workaround *, timer_unstable_counter_workaround);
 EXPORT_SYMBOL_GPL(timer_unstable_counter_workaround);
@@ -423,6 +465,19 @@ static const struct arch_timer_erratum_workaround ool_workarounds[] = {
 		.read_cntvct_el0 = arm64_1188873_read_cntvct_el0,
 	},
 #endif
+#ifdef CONFIG_SUN50I_ERRATUM_UNKNOWN1
+	{
+		.match_type = ate_match_dt,
+		.id = "allwinner,erratum-unknown1",
+		.desc = "Allwinner erratum UNKNOWN1",
+		.read_cntp_tval_el0 = sun50i_a64_read_cntp_tval_el0,
+		.read_cntv_tval_el0 = sun50i_a64_read_cntv_tval_el0,
+		.read_cntpct_el0 = sun50i_a64_read_cntpct_el0,
+		.read_cntvct_el0 = sun50i_a64_read_cntvct_el0,
+		.set_next_event_phys = erratum_set_next_event_tval_phys,
+		.set_next_event_virt = erratum_set_next_event_tval_virt,
+	},
+#endif
 };
 
 typedef bool (*ate_match_fn_t)(const struct arch_timer_erratum_workaround *,
-- 
2.17.1


  reply	other threads:[~2019-02-23 13:08 UTC|newest]

Thread overview: 20+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-02-23 13:05 [GIT PULL] clockevents for 5.1 Daniel Lezcano
2019-02-23 13:06 ` [PATCH 01/18] clocksource/drivers/sun5i: Fail gracefully when clock rate is unavailable Daniel Lezcano
2019-02-23 13:06   ` Daniel Lezcano [this message]
     [not found]     ` <20190226212356.C6B68218A2@mail.kernel.org>
2019-02-27  2:55       ` [PATCH 02/18] clocksource/drivers/arch_timer: Workaround for Allwinner A64 timer instability Samuel Holland
2019-02-23 13:06   ` [PATCH 03/18] clocksource/drivers/exynos_mct: Move one-shot check from tick clear to ISR Daniel Lezcano
2019-02-23 13:06   ` [PATCH 04/18] clocksource/drivers/exynos_mct: Clear timer interrupt when shutdown Daniel Lezcano
2019-02-23 13:06   ` [PATCH 05/18] dt-bindings: timer: renesas, cmt: Document r8a774c0 CMT support Daniel Lezcano
2019-02-23 13:06   ` [PATCH 06/18] dt-bindings: timer: renesas: tmu: Document r8a774c0 bindings Daniel Lezcano
2019-02-23 13:06   ` [PATCH 07/18] clocksource/drivers/riscv: Add required checks during clock source init Daniel Lezcano
2019-02-23 13:06   ` [PATCH 08/18] clocksource/drivers/exynos_mct: Remove dead code Daniel Lezcano
2019-02-23 13:06   ` [PATCH 09/18] clocksource/drivers/exynos_mct: Fix error path in timer resources initialization Daniel Lezcano
2019-02-23 13:06   ` [PATCH 10/18] dt-bindings: timer: mediatek: update bindings for MT7629 SoC Daniel Lezcano
2019-02-23 13:06   ` [PATCH 11/18] clocksource/drivers/exynos_mct: Remove unused header includes Daniel Lezcano
2019-02-23 13:07   ` [PATCH 12/18] dt-bindings: timer: gpt: update binding doc Daniel Lezcano
2019-02-23 13:07   ` [PATCH 13/18] clocksource/drivers/tango-xtal: Rename the file for consistency Daniel Lezcano
2019-02-23 13:07   ` [PATCH 14/18] clocksource/drivers/timer-pxa: " Daniel Lezcano
2019-02-23 13:07   ` [PATCH 15/18] clocksource/drivers/timer-cs5535: " Daniel Lezcano
2019-02-23 13:07   ` [PATCH 16/18] dt-bindings: timer: add Tegra210 timer Daniel Lezcano
2019-02-23 13:07   ` [PATCH 17/18] clocksource/drivers/tegra: Add Tegra210 timer support Daniel Lezcano
2019-02-23 13:07   ` [PATCH 18/18] soc/tegra: default select TEGRA_TIMER for Tegra210 Daniel Lezcano

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190223130707.16704-2-daniel.lezcano@linaro.org \
    --to=daniel.lezcano@linaro.org \
    --cc=andre.przywara@arm.com \
    --cc=catalin.marinas@arm.com \
    --cc=corbet@lwn.net \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-doc@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=marc.zyngier@arm.com \
    --cc=mark.rutland@arm.com \
    --cc=maxime.ripard@bootlin.com \
    --cc=samuel@sholland.org \
    --cc=stable@vger.kernel.org \
    --cc=tglx@linutronix.de \
    --cc=will.deacon@arm.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).