[PATCH AUTOSEL 5.0 01/98] arm64: dts: renesas: r8a77990: Fix SCIF5 DMA channels

[PATCH AUTOSEL 5.0 01/98] arm64: dts: renesas: r8a77990: Fix SCIF5 DMA channels

[Sasha Levin]

From: Takeshi Kihara <takeshi.kihara.df@renesas.com>

[ Upstream commit e20119f7eaaaf6aad5b44f35155ce500429e17f6 ]

According to the R-Car Gen3 Hardware Manual Errata for Rev 1.50 of Feb
12, 2019, the DMA channels for SCIF5 are corrected from 16..47 to 0..15
on R-Car E3.

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Fixes: a5ebe5e49a862e21 ("arm64: dts: renesas: r8a77990: Add SCIF-{0,1,3,4,5} device nodes")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 arch/arm64/boot/dts/renesas/r8a77990.dtsi | 7 +++----
 1 file changed, 3 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/renesas/r8a77990.dtsi b/arch/arm64/boot/dts/renesas/r8a77990.dtsi
index b2f606e286ce..327d12097643 100644
--- a/arch/arm64/boot/dts/renesas/r8a77990.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a77990.dtsi
@@ -2,7 +2,7 @@
 /*
  * Device Tree Source for the R-Car E3 (R8A77990) SoC
  *
- * Copyright (C) 2018 Renesas Electronics Corp.
+ * Copyright (C) 2018-2019 Renesas Electronics Corp.
  */
 
 #include <dt-bindings/clock/r8a77990-cpg-mssr.h>
@@ -1040,9 +1040,8 @@
 				 <&cpg CPG_CORE R8A77990_CLK_S3D1C>,
 				 <&scif_clk>;
 			clock-names = "fck", "brg_int", "scif_clk";
-			dmas = <&dmac1 0x5b>, <&dmac1 0x5a>,
-			       <&dmac2 0x5b>, <&dmac2 0x5a>;
-			dma-names = "tx", "rx", "tx", "rx";
+			dmas = <&dmac0 0x5b>, <&dmac0 0x5a>;
+			dma-names = "tx", "rx";
 			power-domains = <&sysc R8A77990_PD_ALWAYS_ON>;
 			resets = <&cpg 202>;
 			status = "disabled";
-- 
2.19.1

[PATCH AUTOSEL 5.0 02/98] ARM: dts: bcm283x: Fix hdmi hpd gpio pull

[Sasha Levin]

From: Helen Koike <helen.koike@collabora.com>

[ Upstream commit 544e784188f1dd7c797c70b213385e67d92005b6 ]

Raspberry pi board model B revison 2 have the hot plug detector gpio
active high (and not low as it was in the dts).

Signed-off-by: Helen Koike <helen.koike@collabora.com>
Fixes: 49ac67e0c39c ("ARM: bcm2835: Add VC4 to the device tree.")
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
index 5641d162dfdb..28e7513ce617 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
@@ -93,7 +93,7 @@
 };
 
 &hdmi {
-	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
 };
 
 &pwm {
-- 
2.19.1

[PATCH AUTOSEL 5.0 03/98] s390: limit brk randomization to 32MB

[Sasha Levin]

From: Martin Schwidefsky <schwidefsky@de.ibm.com>

[ Upstream commit cd479eccd2e057116d504852814402a1e68ead80 ]

For a 64-bit process the randomization of the program break is quite
large with 1GB. That is as big as the randomization of the anonymous
mapping base, for a test case started with '/lib/ld64.so.1 <exec>'
it can happen that the heap is placed after the stack. To avoid
this limit the program break randomization to 32MB for 64-bit and
keep 8MB for 31-bit.

Reported-by: Stefan Liebler <stli@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 arch/s390/include/asm/elf.h | 11 +++++++----
 1 file changed, 7 insertions(+), 4 deletions(-)

diff --git a/arch/s390/include/asm/elf.h b/arch/s390/include/asm/elf.h
index 7d22a474a040..f74639a05f0f 100644
--- a/arch/s390/include/asm/elf.h
+++ b/arch/s390/include/asm/elf.h
@@ -252,11 +252,14 @@ do {								\
 
 /*
  * Cache aliasing on the latest machines calls for a mapping granularity
- * of 512KB. For 64-bit processes use a 512KB alignment and a randomization
- * of up to 1GB. For 31-bit processes the virtual address space is limited,
- * use no alignment and limit the randomization to 8MB.
+ * of 512KB for the anonymous mapping base. For 64-bit processes use a
+ * 512KB alignment and a randomization of up to 1GB. For 31-bit processes
+ * the virtual address space is limited, use no alignment and limit the
+ * randomization to 8MB.
+ * For the additional randomization of the program break use 32MB for
+ * 64-bit and 8MB for 31-bit.
  */
-#define BRK_RND_MASK	(is_compat_task() ? 0x7ffUL : 0x3ffffUL)
+#define BRK_RND_MASK	(is_compat_task() ? 0x7ffUL : 0x1fffUL)
 #define MMAP_RND_MASK	(is_compat_task() ? 0x7ffUL : 0x3ff80UL)
 #define MMAP_ALIGN_MASK	(is_compat_task() ? 0 : 0x7fUL)
 #define STACK_RND_MASK	MMAP_RND_MASK
-- 
2.19.1

[PATCH AUTOSEL 5.0 04/98] mt76x02: fix hdr pointer in write txwi for USB

[Sasha Levin]

From: Stanislaw Gruszka <sgruszka@redhat.com>

[ Upstream commit 7b25d3b8e485c7721cba9c71b44d1c286e61c8e7 ]

Since we add txwi at the begining of skb->data, it no longer point
to ieee80211_hdr. This breaks settings TS bit for probe response and
beacons.

Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/net/wireless/mediatek/mt76/mt76x02_usb_core.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/mediatek/mt76/mt76x02_usb_core.c b/drivers/net/wireless/mediatek/mt76/mt76x02_usb_core.c
index 81970cf777c0..8cafa5a749ca 100644
--- a/drivers/net/wireless/mediatek/mt76/mt76x02_usb_core.c
+++ b/drivers/net/wireless/mediatek/mt76/mt76x02_usb_core.c
@@ -81,8 +81,9 @@ int mt76x02u_tx_prepare_skb(struct mt76_dev *mdev, void *data,
 
 	mt76x02_insert_hdr_pad(skb);
 
-	txwi = skb_push(skb, sizeof(struct mt76x02_txwi));
+	txwi = (struct mt76x02_txwi *)(skb->data - sizeof(struct mt76x02_txwi));
 	mt76x02_mac_write_txwi(dev, txwi, skb, wcid, sta, len);
+	skb_push(skb, sizeof(struct mt76x02_txwi));
 
 	pid = mt76_tx_status_skb_add(mdev, wcid, skb);
 	txwi->pktid = pid;
-- 
2.19.1

[PATCH AUTOSEL 5.0 05/98] mt76: mt76x2: fix external LNA gain settings

[Sasha Levin]

From: Felix Fietkau <nbd@nbd.name>

[ Upstream commit 45a042e3026824a7e910db7a4dd38fef0540b902 ]

Devices with external LNA need different values for AGC registers 8 and 9

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/net/wireless/mediatek/mt76/mt76x2/phy.c | 11 ++++++++---
 1 file changed, 8 insertions(+), 3 deletions(-)

diff --git a/drivers/net/wireless/mediatek/mt76/mt76x2/phy.c b/drivers/net/wireless/mediatek/mt76/mt76x2/phy.c
index c9634a774705..11167b7af668 100644
--- a/drivers/net/wireless/mediatek/mt76/mt76x2/phy.c
+++ b/drivers/net/wireless/mediatek/mt76/mt76x2/phy.c
@@ -260,10 +260,15 @@ mt76x2_phy_set_gain_val(struct mt76x02_dev *dev)
 	gain_val[0] = dev->cal.agc_gain_cur[0] - dev->cal.agc_gain_adjust;
 	gain_val[1] = dev->cal.agc_gain_cur[1] - dev->cal.agc_gain_adjust;
 
-	if (dev->mt76.chandef.width >= NL80211_CHAN_WIDTH_40)
+	val = 0x1836 << 16;
+	if (!mt76x2_has_ext_lna(dev) &&
+	    dev->mt76.chandef.width >= NL80211_CHAN_WIDTH_40)
 		val = 0x1e42 << 16;
-	else
-		val = 0x1836 << 16;
+
+	if (mt76x2_has_ext_lna(dev) &&
+	    dev->mt76.chandef.chan->band == NL80211_BAND_2GHZ &&
+	    dev->mt76.chandef.width < NL80211_CHAN_WIDTH_40)
+		val = 0x0f36 << 16;
 
 	val |= 0xf8;
 
-- 
2.19.1

[PATCH AUTOSEL 5.0 06/98] mt76: mt76x2: fix 2.4 GHz channel gain settings

[Sasha Levin]

From: Felix Fietkau <nbd@nbd.name>

[ Upstream commit b8cfd87ac24273e36fbd3ecda631f3ba6566d493 ]

AGC register 35, 37 override for the low gain setting should only be done
on 5 GHz. Also, 2.4 GHz needs a different value for register 35

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 .../net/wireless/mediatek/mt76/mt76x2/phy.c   | 19 ++++++++++++++-----
 1 file changed, 14 insertions(+), 5 deletions(-)

diff --git a/drivers/net/wireless/mediatek/mt76/mt76x2/phy.c b/drivers/net/wireless/mediatek/mt76/mt76x2/phy.c
index 11167b7af668..2f618536ef2a 100644
--- a/drivers/net/wireless/mediatek/mt76/mt76x2/phy.c
+++ b/drivers/net/wireless/mediatek/mt76/mt76x2/phy.c
@@ -285,6 +285,7 @@ void mt76x2_phy_update_channel_gain(struct mt76x02_dev *dev)
 {
 	u8 *gain = dev->cal.agc_gain_init;
 	u8 low_gain_delta, gain_delta;
+	u32 agc_35, agc_37;
 	bool gain_change;
 	int low_gain;
 	u32 val;
@@ -321,6 +322,16 @@ void mt76x2_phy_update_channel_gain(struct mt76x02_dev *dev)
 	else
 		low_gain_delta = 14;
 
+	agc_37 = 0x2121262c;
+	if (dev->mt76.chandef.chan->band == NL80211_BAND_2GHZ)
+		agc_35 = 0x11111516;
+	else if (low_gain == 2)
+		agc_35 = agc_37 = 0x08080808;
+	else if (dev->mt76.chandef.width == NL80211_CHAN_WIDTH_80)
+		agc_35 = 0x10101014;
+	else
+		agc_35 = 0x11111116;
+
 	if (low_gain == 2) {
 		mt76_wr(dev, MT_BBP(RXO, 18), 0xf000a990);
 		mt76_wr(dev, MT_BBP(AGC, 35), 0x08080808);
@@ -329,15 +340,13 @@ void mt76x2_phy_update_channel_gain(struct mt76x02_dev *dev)
 		dev->cal.agc_gain_adjust = 0;
 	} else {
 		mt76_wr(dev, MT_BBP(RXO, 18), 0xf000a991);
-		if (dev->mt76.chandef.width == NL80211_CHAN_WIDTH_80)
-			mt76_wr(dev, MT_BBP(AGC, 35), 0x10101014);
-		else
-			mt76_wr(dev, MT_BBP(AGC, 35), 0x11111116);
-		mt76_wr(dev, MT_BBP(AGC, 37), 0x2121262C);
 		gain_delta = 0;
 		dev->cal.agc_gain_adjust = low_gain_delta;
 	}
 
+	mt76_wr(dev, MT_BBP(AGC, 35), agc_35);
+	mt76_wr(dev, MT_BBP(AGC, 37), agc_37);
+
 	dev->cal.agc_gain_cur[0] = gain[0] - gain_delta;
 	dev->cal.agc_gain_cur[1] = gain[1] - gain_delta;
 	mt76x2_phy_set_gain_val(dev);
-- 
2.19.1

[PATCH AUTOSEL 5.0 07/98] net: ieee802154: fix a potential NULL pointer dereference

[Sasha Levin]

From: Kangjie Lu <kjlu@umn.edu>

[ Upstream commit 2795e8c251614ac0784c9d41008551109f665716 ]

In case alloc_ordered_workqueue fails, the fix releases
sources and returns -ENOMEM to avoid NULL pointer dereference.

Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/net/ieee802154/adf7242.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/net/ieee802154/adf7242.c b/drivers/net/ieee802154/adf7242.c
index cd1d8faccca5..cd6b95e673a5 100644
--- a/drivers/net/ieee802154/adf7242.c
+++ b/drivers/net/ieee802154/adf7242.c
@@ -1268,6 +1268,10 @@ static int adf7242_probe(struct spi_device *spi)
 	INIT_DELAYED_WORK(&lp->work, adf7242_rx_cal_work);
 	lp->wqueue = alloc_ordered_workqueue(dev_name(&spi->dev),
 					     WQ_MEM_RECLAIM);
+	if (unlikely(!lp->wqueue)) {
+		ret = -ENOMEM;
+		goto err_hw_init;
+	}
 
 	ret = adf7242_hw_init(lp);
 	if (ret)
-- 
2.19.1

[PATCH AUTOSEL 5.0 08/98] ieee802154: hwsim: propagate genlmsg_reply return code

[Sasha Levin]

From: Li RongQing <lirongqing@baidu.com>

[ Upstream commit 19b39a25388e71390e059906c979f87be4ef0c71 ]

genlmsg_reply can fail, so propagate its return code

Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/net/ieee802154/mac802154_hwsim.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/ieee802154/mac802154_hwsim.c b/drivers/net/ieee802154/mac802154_hwsim.c
index b6743f03dce0..3b88846de31b 100644
--- a/drivers/net/ieee802154/mac802154_hwsim.c
+++ b/drivers/net/ieee802154/mac802154_hwsim.c
@@ -324,7 +324,7 @@ static int hwsim_get_radio_nl(struct sk_buff *msg, struct genl_info *info)
 			goto out_err;
 		}
 
-		genlmsg_reply(skb, info);
+		res = genlmsg_reply(skb, info);
 		break;
 	}
 
-- 
2.19.1

[PATCH AUTOSEL 5.0 09/98] Btrfs: fix file corruption after snapshotting due to mix of buffered/DIO writes

[Sasha Levin]

From: Filipe Manana <fdmanana@suse.com>

[ Upstream commit 609e804d771f59dc5d45a93e5ee0053c74bbe2bf ]

When we are mixing buffered writes with direct IO writes against the same
file and snapshotting is happening concurrently, we can end up with a
corrupt file content in the snapshot. Example:

1) Inode/file is empty.

2) Snapshotting starts.

2) Buffered write at offset 0 length 256Kb. This updates the i_size of the
   inode to 256Kb, disk_i_size remains zero. This happens after the task
   doing the snapshot flushes all existing delalloc.

3) DIO write at offset 256Kb length 768Kb. Once the ordered extent
   completes it sets the inode's disk_i_size to 1Mb (256Kb + 768Kb) and
   updates the inode item in the fs tree with a size of 1Mb (which is
   the value of disk_i_size).

4) The dealloc for the range [0, 256Kb[ did not start yet.

5) The transaction used in the DIO ordered extent completion, which updated
   the inode item, is committed by the snapshotting task.

6) Snapshot creation completes.

7) Dealloc for the range [0, 256Kb[ is flushed.

After that when reading the file from the snapshot we always get zeroes for
the range [0, 256Kb[, the file has a size of 1Mb and the data written by
the direct IO write is found. From an application's point of view this is
a corruption, since in the source subvolume it could never read a version
of the file that included the data from the direct IO write without the
data from the buffered write included as well. In the snapshot's tree,
file extent items are missing for the range [0, 256Kb[.

The issue, obviously, does not happen when using the -o flushoncommit
mount option.

Fix this by flushing delalloc for all the roots that are about to be
snapshotted when committing a transaction. This guarantees total ordering
when updating the disk_i_size of an inode since the flush for dealloc is
done when a transaction is in the TRANS_STATE_COMMIT_START state and wait
is done once no more external writers exist. This is similar to what we
do when using the flushoncommit mount option, but we do it only if the
transaction has snapshots to create and only for the roots of the
subvolumes to be snapshotted. The bulk of the dealloc is flushed in the
snapshot creation ioctl, so the flush work we do inside the transaction
is minimized.

This issue, involving buffered and direct IO writes with snapshotting, is
often triggered by fstest btrfs/078, and got reported by fsck when not
using the NO_HOLES features, for example:

  $ cat results/btrfs/078.full
  (...)
  _check_btrfs_filesystem: filesystem on /dev/sdc is inconsistent
  *** fsck.btrfs output ***
  [1/7] checking root items
  [2/7] checking extents
  [3/7] checking free space cache
  [4/7] checking fs roots
  root 258 inode 264 errors 100, file extent discount
  Found file extent holes:
        start: 524288, len: 65536
  ERROR: errors found in fs roots

Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 fs/btrfs/transaction.c | 49 ++++++++++++++++++++++++++++++++++++------
 1 file changed, 43 insertions(+), 6 deletions(-)

diff --git a/fs/btrfs/transaction.c b/fs/btrfs/transaction.c
index 4ec2b660d014..7f3ece91a4d0 100644
--- a/fs/btrfs/transaction.c
+++ b/fs/btrfs/transaction.c
@@ -1886,8 +1886,10 @@ static void btrfs_cleanup_pending_block_groups(struct btrfs_trans_handle *trans)
        }
 }
 
-static inline int btrfs_start_delalloc_flush(struct btrfs_fs_info *fs_info)
+static inline int btrfs_start_delalloc_flush(struct btrfs_trans_handle *trans)
 {
+	struct btrfs_fs_info *fs_info = trans->fs_info;
+
 	/*
 	 * We use writeback_inodes_sb here because if we used
 	 * btrfs_start_delalloc_roots we would deadlock with fs freeze.
@@ -1897,15 +1899,50 @@ static inline int btrfs_start_delalloc_flush(struct btrfs_fs_info *fs_info)
 	 * from already being in a transaction and our join_transaction doesn't
 	 * have to re-take the fs freeze lock.
 	 */
-	if (btrfs_test_opt(fs_info, FLUSHONCOMMIT))
+	if (btrfs_test_opt(fs_info, FLUSHONCOMMIT)) {
 		writeback_inodes_sb(fs_info->sb, WB_REASON_SYNC);
+	} else {
+		struct btrfs_pending_snapshot *pending;
+		struct list_head *head = &trans->transaction->pending_snapshots;
+
+		/*
+		 * Flush dellaloc for any root that is going to be snapshotted.
+		 * This is done to avoid a corrupted version of files, in the
+		 * snapshots, that had both buffered and direct IO writes (even
+		 * if they were done sequentially) due to an unordered update of
+		 * the inode's size on disk.
+		 */
+		list_for_each_entry(pending, head, list) {
+			int ret;
+
+			ret = btrfs_start_delalloc_snapshot(pending->root);
+			if (ret)
+				return ret;
+		}
+	}
 	return 0;
 }
 
-static inline void btrfs_wait_delalloc_flush(struct btrfs_fs_info *fs_info)
+static inline void btrfs_wait_delalloc_flush(struct btrfs_trans_handle *trans)
 {
-	if (btrfs_test_opt(fs_info, FLUSHONCOMMIT))
+	struct btrfs_fs_info *fs_info = trans->fs_info;
+
+	if (btrfs_test_opt(fs_info, FLUSHONCOMMIT)) {
 		btrfs_wait_ordered_roots(fs_info, U64_MAX, 0, (u64)-1);
+	} else {
+		struct btrfs_pending_snapshot *pending;
+		struct list_head *head = &trans->transaction->pending_snapshots;
+
+		/*
+		 * Wait for any dellaloc that we started previously for the roots
+		 * that are going to be snapshotted. This is to avoid a corrupted
+		 * version of files in the snapshots that had both buffered and
+		 * direct IO writes (even if they were done sequentially).
+		 */
+		list_for_each_entry(pending, head, list)
+			btrfs_wait_ordered_extents(pending->root,
+						   U64_MAX, 0, U64_MAX);
+	}
 }
 
 int btrfs_commit_transaction(struct btrfs_trans_handle *trans)
@@ -2024,7 +2061,7 @@ int btrfs_commit_transaction(struct btrfs_trans_handle *trans)
 
 	extwriter_counter_dec(cur_trans, trans->type);
 
-	ret = btrfs_start_delalloc_flush(fs_info);
+	ret = btrfs_start_delalloc_flush(trans);
 	if (ret)
 		goto cleanup_transaction;
 
@@ -2040,7 +2077,7 @@ int btrfs_commit_transaction(struct btrfs_trans_handle *trans)
 	if (ret)
 		goto cleanup_transaction;
 
-	btrfs_wait_delalloc_flush(fs_info);
+	btrfs_wait_delalloc_flush(trans);
 
 	btrfs_scrub_pause(fs_info);
 	/*
-- 
2.19.1

[PATCH AUTOSEL 5.0 10/98] net: stmmac: don't set own bit too early for jumbo frames

[Sasha Levin]

From: Aaro Koskinen <aaro.koskinen@nokia.com>

[ Upstream commit 80acbed9f8fca1db3fbe915540b756f048aa0fd7 ]

Commit 0e80bdc9a72d ("stmmac: first frame prep at the end of xmit
routine") overlooked jumbo frames when re-ordering the code, and as a
result the own bit was not getting set anymore for the first jumbo frame
descriptor. Commit 487e2e22ab79 ("net: stmmac: Set OWN bit for jumbo
frames") tried to fix this, but now the bit is getting set too early and
the DMA may start while we are still setting up the remaining descriptors.
And with the chain mode the own bit remains still unset.

Fix by setting the own bit at the end of xmit also with jumbo frames.

Fixes: 0e80bdc9a72d ("stmmac: first frame prep at the end of xmit routine")
Fixes: 487e2e22ab79 ("net: stmmac: Set OWN bit for jumbo frames")
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/net/ethernet/stmicro/stmmac/ring_mode.c   |  4 ++--
 drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 14 ++++++++------
 2 files changed, 10 insertions(+), 8 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/ring_mode.c b/drivers/net/ethernet/stmicro/stmmac/ring_mode.c
index c0c75c111abb..afed0f0f4027 100644
--- a/drivers/net/ethernet/stmicro/stmmac/ring_mode.c
+++ b/drivers/net/ethernet/stmicro/stmmac/ring_mode.c
@@ -59,7 +59,7 @@ static int jumbo_frm(void *p, struct sk_buff *skb, int csum)
 
 		desc->des3 = cpu_to_le32(des2 + BUF_SIZE_4KiB);
 		stmmac_prepare_tx_desc(priv, desc, 1, bmax, csum,
-				STMMAC_RING_MODE, 1, false, skb->len);
+				STMMAC_RING_MODE, 0, false, skb->len);
 		tx_q->tx_skbuff[entry] = NULL;
 		entry = STMMAC_GET_ENTRY(entry, DMA_TX_SIZE);
 
@@ -91,7 +91,7 @@ static int jumbo_frm(void *p, struct sk_buff *skb, int csum)
 		tx_q->tx_skbuff_dma[entry].is_jumbo = true;
 		desc->des3 = cpu_to_le32(des2 + BUF_SIZE_4KiB);
 		stmmac_prepare_tx_desc(priv, desc, 1, nopaged_len, csum,
-				STMMAC_RING_MODE, 1, true, skb->len);
+				STMMAC_RING_MODE, 0, true, skb->len);
 	}
 
 	tx_q->cur_tx = entry;
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index 019ab99e65bb..ff7751f6e828 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -3192,14 +3192,16 @@ static netdev_tx_t stmmac_xmit(struct sk_buff *skb, struct net_device *dev)
 		stmmac_prepare_tx_desc(priv, first, 1, nopaged_len,
 				csum_insertion, priv->mode, 1, last_segment,
 				skb->len);
-
-		/* The own bit must be the latest setting done when prepare the
-		 * descriptor and then barrier is needed to make sure that
-		 * all is coherent before granting the DMA engine.
-		 */
-		wmb();
+	} else {
+		stmmac_set_tx_owner(priv, first);
 	}
 
+	/* The own bit must be the latest setting done when prepare the
+	 * descriptor and then barrier is needed to make sure that
+	 * all is coherent before granting the DMA engine.
+	 */
+	wmb();
+
 	netdev_tx_sent_queue(netdev_get_tx_queue(dev, queue), skb->len);
 
 	stmmac_enable_dma_transmission(priv, priv->ioaddr);
-- 
2.19.1

[PATCH AUTOSEL 5.0 11/98] net: stmmac: fix jumbo frame sending with non-linear skbs

[Sasha Levin]

From: Aaro Koskinen <aaro.koskinen@nokia.com>

[ Upstream commit 58f2ce6f61615dfd8dd3cc01c9e5bb54ed35637e ]

When sending non-linear skbs with jumbo frames, we set up the non-paged
data and mark that as a last segment, although the paged fragments are
also prepared. This will stall the TX queue and trigger a watchdog warning
(a simple reproducer is to run an iperf client mode TCP test with a large
MTU - networking fails instantly).

Fix by checking if the skb is non-linear.

Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/net/ethernet/stmicro/stmmac/ring_mode.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/ring_mode.c b/drivers/net/ethernet/stmicro/stmmac/ring_mode.c
index afed0f0f4027..4d9bcb4d0378 100644
--- a/drivers/net/ethernet/stmicro/stmmac/ring_mode.c
+++ b/drivers/net/ethernet/stmicro/stmmac/ring_mode.c
@@ -79,7 +79,8 @@ static int jumbo_frm(void *p, struct sk_buff *skb, int csum)
 
 		desc->des3 = cpu_to_le32(des2 + BUF_SIZE_4KiB);
 		stmmac_prepare_tx_desc(priv, desc, 0, len, csum,
-				STMMAC_RING_MODE, 1, true, skb->len);
+				STMMAC_RING_MODE, 1, !skb_is_nonlinear(skb),
+				skb->len);
 	} else {
 		des2 = dma_map_single(priv->device, skb->data,
 				      nopaged_len, DMA_TO_DEVICE);
@@ -91,7 +92,8 @@ static int jumbo_frm(void *p, struct sk_buff *skb, int csum)
 		tx_q->tx_skbuff_dma[entry].is_jumbo = true;
 		desc->des3 = cpu_to_le32(des2 + BUF_SIZE_4KiB);
 		stmmac_prepare_tx_desc(priv, desc, 1, nopaged_len, csum,
-				STMMAC_RING_MODE, 0, true, skb->len);
+				STMMAC_RING_MODE, 0, !skb_is_nonlinear(skb),
+				skb->len);
 	}
 
 	tx_q->cur_tx = entry;
-- 
2.19.1

[PATCH AUTOSEL 5.0 12/98] qlcnic: Avoid potential NULL pointer dereference

[Sasha Levin]

From: Aditya Pakki <pakki001@umn.edu>

[ Upstream commit 5bf7295fe34a5251b1d241b9736af4697b590670 ]

netdev_alloc_skb can fail and return a NULL pointer which is
dereferenced without a check. The patch avoids such a scenario.

Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c
index 3b0adda7cc9c..a4cd6f2cfb86 100644
--- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c
+++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c
@@ -1048,6 +1048,8 @@ int qlcnic_do_lb_test(struct qlcnic_adapter *adapter, u8 mode)
 
 	for (i = 0; i < QLCNIC_NUM_ILB_PKT; i++) {
 		skb = netdev_alloc_skb(adapter->netdev, QLCNIC_ILB_PKT_SIZE);
+		if (!skb)
+			break;
 		qlcnic_create_loopback_buff(skb->data, adapter->mac_addr);
 		skb_put(skb, QLCNIC_ILB_PKT_SIZE);
 		adapter->ahw->diag_cnt = 0;
-- 
2.19.1

[PATCH AUTOSEL 5.0 13/98] xsk: fix umem memory leak on cleanup

[Sasha Levin]

From: Björn Töpel <bjorn.topel@intel.com>

[ Upstream commit 044175a06706d516aa42874bb44dbbfc3c4d20eb ]

When the umem is cleaned up, the task that created it might already be
gone. If the task was gone, the xdp_umem_release function did not free
the pages member of struct xdp_umem.

It turned out that the task lookup was not needed at all; The code was
a left-over when we moved from task accounting to user accounting [1].

This patch fixes the memory leak by removing the task lookup logic
completely.

[1] https://lore.kernel.org/netdev/20180131135356.19134-3-bjorn.topel@gmail.com/

Link: https://lore.kernel.org/netdev/c1cb2ca8-6a14-3980-8672-f3de0bb38dfd@suse.cz/
Fixes: c0c77d8fb787 ("xsk: add user memory registration support sockopt")
Reported-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 include/net/xdp_sock.h |  1 -
 net/xdp/xdp_umem.c     | 19 +------------------
 2 files changed, 1 insertion(+), 19 deletions(-)

diff --git a/include/net/xdp_sock.h b/include/net/xdp_sock.h
index 13acb9803a6d..05d39e579953 100644
--- a/include/net/xdp_sock.h
+++ b/include/net/xdp_sock.h
@@ -36,7 +36,6 @@ struct xdp_umem {
 	u32 headroom;
 	u32 chunk_size_nohr;
 	struct user_struct *user;
-	struct pid *pid;
 	unsigned long address;
 	refcount_t users;
 	struct work_struct work;
diff --git a/net/xdp/xdp_umem.c b/net/xdp/xdp_umem.c
index 37e1fe180769..9c767c68ed3a 100644
--- a/net/xdp/xdp_umem.c
+++ b/net/xdp/xdp_umem.c
@@ -189,9 +189,6 @@ static void xdp_umem_unaccount_pages(struct xdp_umem *umem)
 
 static void xdp_umem_release(struct xdp_umem *umem)
 {
-	struct task_struct *task;
-	struct mm_struct *mm;
-
 	xdp_umem_clear_dev(umem);
 
 	if (umem->fq) {
@@ -208,21 +205,10 @@ static void xdp_umem_release(struct xdp_umem *umem)
 
 	xdp_umem_unpin_pages(umem);
 
-	task = get_pid_task(umem->pid, PIDTYPE_PID);
-	put_pid(umem->pid);
-	if (!task)
-		goto out;
-	mm = get_task_mm(task);
-	put_task_struct(task);
-	if (!mm)
-		goto out;
-
-	mmput(mm);
 	kfree(umem->pages);
 	umem->pages = NULL;
 
 	xdp_umem_unaccount_pages(umem);
-out:
 	kfree(umem);
 }
 
@@ -351,7 +337,6 @@ static int xdp_umem_reg(struct xdp_umem *umem, struct xdp_umem_reg *mr)
 	if (size_chk < 0)
 		return -EINVAL;
 
-	umem->pid = get_task_pid(current, PIDTYPE_PID);
 	umem->address = (unsigned long)addr;
 	umem->chunk_mask = ~((u64)chunk_size - 1);
 	umem->size = size;
@@ -367,7 +352,7 @@ static int xdp_umem_reg(struct xdp_umem *umem, struct xdp_umem_reg *mr)
 
 	err = xdp_umem_account_pages(umem);
 	if (err)
-		goto out;
+		return err;
 
 	err = xdp_umem_pin_pages(umem);
 	if (err)
@@ -386,8 +371,6 @@ static int xdp_umem_reg(struct xdp_umem *umem, struct xdp_umem_reg *mr)
 
 out_account:
 	xdp_umem_unaccount_pages(umem);
-out:
-	put_pid(umem->pid);
 	return err;
 }
 
-- 
2.19.1

[PATCH AUTOSEL 5.0 14/98] staging: axis-fifo: add CONFIG_OF dependency

[Sasha Levin]

From: Arnd Bergmann <arnd@arndb.de>

[ Upstream commit 1beea6204e2304dd11600791d8dad8e7350af6ad ]

When building without CONFIG_OF, the compiler loses track of the flow
control in axis_fifo_probe(), and thinks that many variables are used
without an initialization even though we actually leave the function
before the first use:

drivers/staging/axis-fifo/axis-fifo.c: In function 'axis_fifo_probe':
drivers/staging/axis-fifo/axis-fifo.c:900:5: error: 'rxd_tdata_width' may be used uninitialized in this function [-Werror=maybe-uninitialized]
  if (rxd_tdata_width != 32) {
     ^
drivers/staging/axis-fifo/axis-fifo.c:907:5: error: 'txd_tdata_width' may be used uninitialized in this function [-Werror=maybe-uninitialized]
  if (txd_tdata_width != 32) {
     ^
drivers/staging/axis-fifo/axis-fifo.c:914:5: error: 'has_tdest' may be used uninitialized in this function [-Werror=maybe-uninitialized]
  if (has_tdest) {
     ^
drivers/staging/axis-fifo/axis-fifo.c:919:5: error: 'has_tid' may be used uninitialized in this function [-Werror=maybe-uninitialized]

When CONFIG_OF is set, this does not happen, and since the driver cannot
work without it, just add that option as a Kconfig dependency.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/staging/axis-fifo/Kconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/staging/axis-fifo/Kconfig b/drivers/staging/axis-fifo/Kconfig
index 687537203d9c..d9725888af6f 100644
--- a/drivers/staging/axis-fifo/Kconfig
+++ b/drivers/staging/axis-fifo/Kconfig
@@ -3,6 +3,7 @@
 #
 config XIL_AXIS_FIFO
 	tristate "Xilinx AXI-Stream FIFO IP core driver"
+	depends on OF
 	default n
 	help
 	  This adds support for the Xilinx AXI-Stream
-- 
2.19.1

[PATCH AUTOSEL 5.0 15/98] staging, mt7621-pci: fix build without pci support

[Sasha Levin]

From: Maxim Zhukov <mussitantesmortem@gmail.com>

[ Upstream commit 90cd9bed5adb3e3bd4d3ac4cbcecbc4a8028bbaf ]

Add depends on PCI for PCI_MT7621

Signed-off-by: Maxim Zhukov <mussitantesmortem@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/staging/mt7621-pci/Kconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/staging/mt7621-pci/Kconfig b/drivers/staging/mt7621-pci/Kconfig
index d33533872a16..c8fa17cfa807 100644
--- a/drivers/staging/mt7621-pci/Kconfig
+++ b/drivers/staging/mt7621-pci/Kconfig
@@ -1,6 +1,7 @@
 config PCI_MT7621
 	tristate "MediaTek MT7621 PCI Controller"
 	depends on RALINK
+	depends on PCI
 	select PCI_DRIVERS_GENERIC
 	help
 	  This selects a driver for the MediaTek MT7621 PCI Controller.
-- 
2.19.1

[PATCH AUTOSEL 5.0 16/98] netfilter: nft_set_rbtree: check for inactive element after flag mismatch

[Sasha Levin]

From: Pablo Neira Ayuso <pablo@netfilter.org>

[ Upstream commit 05b7639da55f5555b9866a1f4b7e8995232a6323 ]

Otherwise, we hit bogus ENOENT when removing elements.

Fixes: e701001e7cbe ("netfilter: nft_rbtree: allow adjacent intervals with dynamic updates")
Reported-by: Václav Zindulka <vaclav.zindulka@tlapnet.cz>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 net/netfilter/nft_set_rbtree.c | 7 +++----
 1 file changed, 3 insertions(+), 4 deletions(-)

diff --git a/net/netfilter/nft_set_rbtree.c b/net/netfilter/nft_set_rbtree.c
index fa61208371f8..321a0036fdf5 100644
--- a/net/netfilter/nft_set_rbtree.c
+++ b/net/netfilter/nft_set_rbtree.c
@@ -308,10 +308,6 @@ static void *nft_rbtree_deactivate(const struct net *net,
 		else if (d > 0)
 			parent = parent->rb_right;
 		else {
-			if (!nft_set_elem_active(&rbe->ext, genmask)) {
-				parent = parent->rb_left;
-				continue;
-			}
 			if (nft_rbtree_interval_end(rbe) &&
 			    !nft_rbtree_interval_end(this)) {
 				parent = parent->rb_left;
@@ -320,6 +316,9 @@ static void *nft_rbtree_deactivate(const struct net *net,
 				   nft_rbtree_interval_end(this)) {
 				parent = parent->rb_right;
 				continue;
+			} else if (!nft_set_elem_active(&rbe->ext, genmask)) {
+				parent = parent->rb_left;
+				continue;
 			}
 			nft_rbtree_flush(net, set, rbe);
 			return rbe;
-- 
2.19.1

[PATCH AUTOSEL 5.0 17/98] netfilter: bridge: set skb transport_header before entering NF_INET_PRE_ROUTING

[Sasha Levin]

From: Xin Long <lucien.xin@gmail.com>

[ Upstream commit e166e4fdaced850bee3d5ee12a5740258fb30587 ]

Since Commit 21d1196a35f5 ("ipv4: set transport header earlier"),
skb->transport_header has been always set before entering INET
netfilter. This patch is to set skb->transport_header for bridge
before entering INET netfilter by bridge-nf-call-iptables.

It also fixes an issue that sctp_error() couldn't compute a right
csum due to unset skb->transport_header.

Fixes: e6d8b64b34aa ("net: sctp: fix and consolidate SCTP checksumming code")
Reported-by: Li Shuang <shuali@redhat.com>
Suggested-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 net/bridge/br_netfilter_hooks.c | 1 +
 net/bridge/br_netfilter_ipv6.c  | 2 ++
 2 files changed, 3 insertions(+)

diff --git a/net/bridge/br_netfilter_hooks.c b/net/bridge/br_netfilter_hooks.c
index 40d058378b52..fc605758323b 100644
--- a/net/bridge/br_netfilter_hooks.c
+++ b/net/bridge/br_netfilter_hooks.c
@@ -502,6 +502,7 @@ static unsigned int br_nf_pre_routing(void *priv,
 	nf_bridge->ipv4_daddr = ip_hdr(skb)->daddr;
 
 	skb->protocol = htons(ETH_P_IP);
+	skb->transport_header = skb->network_header + ip_hdr(skb)->ihl * 4;
 
 	NF_HOOK(NFPROTO_IPV4, NF_INET_PRE_ROUTING, state->net, state->sk, skb,
 		skb->dev, NULL,
diff --git a/net/bridge/br_netfilter_ipv6.c b/net/bridge/br_netfilter_ipv6.c
index 564710f88f93..e88d6641647b 100644
--- a/net/bridge/br_netfilter_ipv6.c
+++ b/net/bridge/br_netfilter_ipv6.c
@@ -235,6 +235,8 @@ unsigned int br_nf_pre_routing_ipv6(void *priv,
 	nf_bridge->ipv6_daddr = ipv6_hdr(skb)->daddr;
 
 	skb->protocol = htons(ETH_P_IPV6);
+	skb->transport_header = skb->network_header + sizeof(struct ipv6hdr);
+
 	NF_HOOK(NFPROTO_IPV6, NF_INET_PRE_ROUTING, state->net, state->sk, skb,
 		skb->dev, NULL,
 		br_nf_pre_routing_finish_ipv6);
-- 
2.19.1

[PATCH AUTOSEL 5.0 18/98] netfilter: fix NETFILTER_XT_TARGET_TEE dependencies

[Sasha Levin]

From: Arnd Bergmann <arnd@arndb.de>

[ Upstream commit d1fa381033eb718df5c602f64b6e88676138dfc6 ]

With NETFILTER_XT_TARGET_TEE=y and IP6_NF_IPTABLES=m, we get a link
error when referencing the NF_DUP_IPV6 module:

net/netfilter/xt_TEE.o: In function `tee_tg6':
xt_TEE.c:(.text+0x14): undefined reference to `nf_dup_ipv6'

The problem here is the 'select NF_DUP_IPV6 if IP6_NF_IPTABLES'
that forces NF_DUP_IPV6 to be =m as well rather than setting it
to =y as was intended here. Adding a soft dependency on
IP6_NF_IPTABLES avoids that broken configuration.

Fixes: 5d400a4933e8 ("netfilter: Kconfig: Change select IPv6 dependencies")
Cc: Máté Eckl <ecklm94@gmail.com>
Cc: Taehee Yoo <ap420073@gmail.com>
Link: https://patchwork.ozlabs.org/patch/999498/
Link: https://lore.kernel.org/patchwork/patch/960062/
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 net/netfilter/Kconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/net/netfilter/Kconfig b/net/netfilter/Kconfig
index beb3a69ce1d4..0f0e5806bf77 100644
--- a/net/netfilter/Kconfig
+++ b/net/netfilter/Kconfig
@@ -995,6 +995,7 @@ config NETFILTER_XT_TARGET_TEE
 	depends on NETFILTER_ADVANCED
 	depends on IPV6 || IPV6=n
 	depends on !NF_CONNTRACK || NF_CONNTRACK
+	depends on IP6_NF_IPTABLES || !IP6_NF_IPTABLES
 	select NF_DUP_IPV4
 	select NF_DUP_IPV6 if IP6_NF_IPTABLES
 	---help---
-- 
2.19.1

[PATCH AUTOSEL 5.0 19/98] netfilter: ip6t_srh: fix NULL pointer dereferences

[Sasha Levin]

From: Kangjie Lu <kjlu@umn.edu>

[ Upstream commit 6d65561f3d5ec933151939c543d006b79044e7a6 ]

skb_header_pointer may return NULL. The current code dereference
its return values without a NULL check.

The fix inserts the checks to avoid NULL pointer dereferences.

Fixes: 202a8ff545cc ("netfilter: add IPv6 segment routing header 'srh' match")
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 net/ipv6/netfilter/ip6t_srh.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/net/ipv6/netfilter/ip6t_srh.c b/net/ipv6/netfilter/ip6t_srh.c
index 1059894a6f4c..4cb83fb69844 100644
--- a/net/ipv6/netfilter/ip6t_srh.c
+++ b/net/ipv6/netfilter/ip6t_srh.c
@@ -210,6 +210,8 @@ static bool srh1_mt6(const struct sk_buff *skb, struct xt_action_param *par)
 		psidoff = srhoff + sizeof(struct ipv6_sr_hdr) +
 			  ((srh->segments_left + 1) * sizeof(struct in6_addr));
 		psid = skb_header_pointer(skb, psidoff, sizeof(_psid), &_psid);
+		if (!psid)
+			return false;
 		if (NF_SRH_INVF(srhinfo, IP6T_SRH_INV_PSID,
 				ipv6_masked_addr_cmp(psid, &srhinfo->psid_msk,
 						     &srhinfo->psid_addr)))
@@ -223,6 +225,8 @@ static bool srh1_mt6(const struct sk_buff *skb, struct xt_action_param *par)
 		nsidoff = srhoff + sizeof(struct ipv6_sr_hdr) +
 			  ((srh->segments_left - 1) * sizeof(struct in6_addr));
 		nsid = skb_header_pointer(skb, nsidoff, sizeof(_nsid), &_nsid);
+		if (!nsid)
+			return false;
 		if (NF_SRH_INVF(srhinfo, IP6T_SRH_INV_NSID,
 				ipv6_masked_addr_cmp(nsid, &srhinfo->nsid_msk,
 						     &srhinfo->nsid_addr)))
@@ -233,6 +237,8 @@ static bool srh1_mt6(const struct sk_buff *skb, struct xt_action_param *par)
 	if (srhinfo->mt_flags & IP6T_SRH_LSID) {
 		lsidoff = srhoff + sizeof(struct ipv6_sr_hdr);
 		lsid = skb_header_pointer(skb, lsidoff, sizeof(_lsid), &_lsid);
+		if (!lsid)
+			return false;
 		if (NF_SRH_INVF(srhinfo, IP6T_SRH_INV_LSID,
 				ipv6_masked_addr_cmp(lsid, &srhinfo->lsid_msk,
 						     &srhinfo->lsid_addr)))
-- 
2.19.1

[PATCH AUTOSEL 5.0 20/98] netfilter: nf_tables: bogus EBUSY in helper removal from transaction

[Sasha Levin]

From: Pablo Neira Ayuso <pablo@netfilter.org>

[ Upstream commit 8ffcd32f64633926163cdd07a7d295c500a947d1 ]

Proper use counter updates when activating and deactivating the object,
otherwise, this hits bogus EBUSY error.

Fixes: cd5125d8f518 ("netfilter: nf_tables: split set destruction in deactivate and destroy phase")
Reported-by: Laura Garcia <nevola@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 net/netfilter/nft_objref.c | 19 ++++++++++++++++---
 1 file changed, 16 insertions(+), 3 deletions(-)

diff --git a/net/netfilter/nft_objref.c b/net/netfilter/nft_objref.c
index ae178e914486..1dfc621cedaa 100644
--- a/net/netfilter/nft_objref.c
+++ b/net/netfilter/nft_objref.c
@@ -64,21 +64,34 @@ nla_put_failure:
 	return -1;
 }
 
-static void nft_objref_destroy(const struct nft_ctx *ctx,
-			       const struct nft_expr *expr)
+static void nft_objref_deactivate(const struct nft_ctx *ctx,
+				  const struct nft_expr *expr,
+				  enum nft_trans_phase phase)
 {
 	struct nft_object *obj = nft_objref_priv(expr);
 
+	if (phase == NFT_TRANS_COMMIT)
+		return;
+
 	obj->use--;
 }
 
+static void nft_objref_activate(const struct nft_ctx *ctx,
+				const struct nft_expr *expr)
+{
+	struct nft_object *obj = nft_objref_priv(expr);
+
+	obj->use++;
+}
+
 static struct nft_expr_type nft_objref_type;
 static const struct nft_expr_ops nft_objref_ops = {
 	.type		= &nft_objref_type,
 	.size		= NFT_EXPR_SIZE(sizeof(struct nft_object *)),
 	.eval		= nft_objref_eval,
 	.init		= nft_objref_init,
-	.destroy	= nft_objref_destroy,
+	.activate	= nft_objref_activate,
+	.deactivate	= nft_objref_deactivate,
 	.dump		= nft_objref_dump,
 };
 
-- 
2.19.1

[PATCH AUTOSEL 5.0 21/98] s390/qeth: fix race when initializing the IP address table

[Sasha Levin]

From: Julian Wiedmann <jwi@linux.ibm.com>

[ Upstream commit 7221b727f0079a32aca91f657141e1de564d4b97 ]

The ucast IP table is utilized by some of the L3-specific sysfs attributes
that qeth_l3_create_device_attributes() provides. So initialize the table
_before_ registering the attributes.

Fixes: ebccc7397e4a ("s390/qeth: add missing hash table initializations")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/s390/net/qeth_l3_main.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/s390/net/qeth_l3_main.c b/drivers/s390/net/qeth_l3_main.c
index df34bff4ac31..f73ce96e9603 100644
--- a/drivers/s390/net/qeth_l3_main.c
+++ b/drivers/s390/net/qeth_l3_main.c
@@ -2316,12 +2316,14 @@ static int qeth_l3_probe_device(struct ccwgroup_device *gdev)
 	struct qeth_card *card = dev_get_drvdata(&gdev->dev);
 	int rc;
 
+	hash_init(card->ip_htable);
+
 	if (gdev->dev.type == &qeth_generic_devtype) {
 		rc = qeth_l3_create_device_attributes(&gdev->dev);
 		if (rc)
 			return rc;
 	}
-	hash_init(card->ip_htable);
+
 	hash_init(card->ip_mc_htable);
 	card->info.hwtrap = 0;
 	return 0;
-- 
2.19.1

[PATCH AUTOSEL 5.0 22/98] ARM: imx51: fix a leaked reference by adding missing of_node_put

[Sasha Levin]

From: Wen Yang <wen.yang99@zte.com.cn>

[ Upstream commit 0c17e83fe423467e3ccf0a02f99bd050a73bbeb4 ]

The call to of_get_next_child returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.

Detected by coccinelle with the following warnings:
./arch/arm/mach-imx/mach-imx51.c:64:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 57, but without a corresponding object release within this function.

Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 arch/arm/mach-imx/mach-imx51.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/mach-imx/mach-imx51.c b/arch/arm/mach-imx/mach-imx51.c
index c7169c2f94c4..08c7892866c2 100644
--- a/arch/arm/mach-imx/mach-imx51.c
+++ b/arch/arm/mach-imx/mach-imx51.c
@@ -59,6 +59,7 @@ static void __init imx51_m4if_setup(void)
 		return;
 
 	m4if_base = of_iomap(np, 0);
+	of_node_put(np);
 	if (!m4if_base) {
 		pr_err("Unable to map M4IF registers\n");
 		return;
-- 
2.19.1

[PATCH AUTOSEL 5.0 23/98] sc16is7xx: missing unregister/delete driver on error in sc16is7xx_init()

[Sasha Levin]

From: Mao Wenan <maowenan@huawei.com>

[ Upstream commit ac0cdb3d990108df795b676cd0d0e65ac34b2273 ]

Add the missing uart_unregister_driver() and i2c_del_driver() before return
from sc16is7xx_init() in the error handling case.

Signed-off-by: Mao Wenan <maowenan@huawei.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/tty/serial/sc16is7xx.c | 12 ++++++++++--
 1 file changed, 10 insertions(+), 2 deletions(-)

diff --git a/drivers/tty/serial/sc16is7xx.c b/drivers/tty/serial/sc16is7xx.c
index 268098681856..114e94f476c6 100644
--- a/drivers/tty/serial/sc16is7xx.c
+++ b/drivers/tty/serial/sc16is7xx.c
@@ -1509,7 +1509,7 @@ static int __init sc16is7xx_init(void)
 	ret = i2c_add_driver(&sc16is7xx_i2c_uart_driver);
 	if (ret < 0) {
 		pr_err("failed to init sc16is7xx i2c --> %d\n", ret);
-		return ret;
+		goto err_i2c;
 	}
 #endif
 
@@ -1517,10 +1517,18 @@ static int __init sc16is7xx_init(void)
 	ret = spi_register_driver(&sc16is7xx_spi_uart_driver);
 	if (ret < 0) {
 		pr_err("failed to init sc16is7xx spi --> %d\n", ret);
-		return ret;
+		goto err_spi;
 	}
 #endif
 	return ret;
+
+err_spi:
+#ifdef CONFIG_SERIAL_SC16IS7XX_I2C
+	i2c_del_driver(&sc16is7xx_i2c_uart_driver);
+#endif
+err_i2c:
+	uart_unregister_driver(&sc16is7xx_uart);
+	return ret;
 }
 module_init(sc16is7xx_init);
 
-- 
2.19.1

[PATCH AUTOSEL 5.0 24/98] serial: ar933x_uart: Fix build failure with disabled console

[Sasha Levin]

From: Petr Štetiar <ynezz@true.cz>

[ Upstream commit 72ff51d8dd262d1fef25baedc2ac35116435be47 ]

Andrey has reported on OpenWrt's bug tracking system[1], that he
currently can't use ar93xx_uart as pure serial UART without console
(CONFIG_SERIAL_8250_CONSOLE and CONFIG_SERIAL_AR933X_CONSOLE undefined),
because compilation ends with following error:

 ar933x_uart.c: In function 'ar933x_uart_console_write':
 ar933x_uart.c:550:14: error: 'struct uart_port' has no
                               member named 'sysrq'

So this patch moves all the code related to console handling behind
series of CONFIG_SERIAL_AR933X_CONSOLE ifdefs.

1. https://bugs.openwrt.org/index.php?do=details&task_id=2152

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Andrey Batyiev <batyiev@gmail.com>
Reported-by: Andrey Batyiev <batyiev@gmail.com>
Tested-by: Andrey Batyiev <batyiev@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/tty/serial/ar933x_uart.c | 24 ++++++++----------------
 1 file changed, 8 insertions(+), 16 deletions(-)

diff --git a/drivers/tty/serial/ar933x_uart.c b/drivers/tty/serial/ar933x_uart.c
index db5df3d54818..3bdd56a1021b 100644
--- a/drivers/tty/serial/ar933x_uart.c
+++ b/drivers/tty/serial/ar933x_uart.c
@@ -49,11 +49,6 @@ struct ar933x_uart_port {
 	struct clk		*clk;
 };
 
-static inline bool ar933x_uart_console_enabled(void)
-{
-	return IS_ENABLED(CONFIG_SERIAL_AR933X_CONSOLE);
-}
-
 static inline unsigned int ar933x_uart_read(struct ar933x_uart_port *up,
 					    int offset)
 {
@@ -508,6 +503,7 @@ static const struct uart_ops ar933x_uart_ops = {
 	.verify_port	= ar933x_uart_verify_port,
 };
 
+#ifdef CONFIG_SERIAL_AR933X_CONSOLE
 static struct ar933x_uart_port *
 ar933x_console_ports[CONFIG_SERIAL_AR933X_NR_UARTS];
 
@@ -604,14 +600,7 @@ static struct console ar933x_uart_console = {
 	.index		= -1,
 	.data		= &ar933x_uart_driver,
 };
-
-static void ar933x_uart_add_console_port(struct ar933x_uart_port *up)
-{
-	if (!ar933x_uart_console_enabled())
-		return;
-
-	ar933x_console_ports[up->port.line] = up;
-}
+#endif /* CONFIG_SERIAL_AR933X_CONSOLE */
 
 static struct uart_driver ar933x_uart_driver = {
 	.owner		= THIS_MODULE,
@@ -700,7 +689,9 @@ static int ar933x_uart_probe(struct platform_device *pdev)
 	baud = ar933x_uart_get_baud(port->uartclk, 0, AR933X_UART_MAX_STEP);
 	up->max_baud = min_t(unsigned int, baud, AR933X_UART_MAX_BAUD);
 
-	ar933x_uart_add_console_port(up);
+#ifdef CONFIG_SERIAL_AR933X_CONSOLE
+	ar933x_console_ports[up->port.line] = up;
+#endif
 
 	ret = uart_add_one_port(&ar933x_uart_driver, &up->port);
 	if (ret)
@@ -749,8 +740,9 @@ static int __init ar933x_uart_init(void)
 {
 	int ret;
 
-	if (ar933x_uart_console_enabled())
-		ar933x_uart_driver.cons = &ar933x_uart_console;
+#ifdef CONFIG_SERIAL_AR933X_CONSOLE
+	ar933x_uart_driver.cons = &ar933x_uart_console;
+#endif
 
 	ret = uart_register_driver(&ar933x_uart_driver);
 	if (ret)
-- 
2.19.1

[PATCH AUTOSEL 5.0 25/98] KVM: arm64: Reset the PMU in preemptible context

[Sasha Levin]

From: Marc Zyngier <marc.zyngier@arm.com>

[ Upstream commit ebff0b0e3d3c862c16c487959db5e0d879632559 ]

We've become very cautious to now always reset the vcpu when nothing
is loaded on the physical CPU. To do so, we now disable preemption
and do a kvm_arch_vcpu_put() to make sure we have all the state
in memory (and that it won't be loaded behind out back).

This now causes issues with resetting the PMU, which calls into perf.
Perf itself uses mutexes, which clashes with the lack of preemption.
It is worth realizing that the PMU is fully emulated, and that
no PMU state is ever loaded on the physical CPU. This means we can
perfectly reset the PMU outside of the non-preemptible section.

Fixes: e761a927bc9a ("KVM: arm/arm64: Reset the VCPU without preemption and vcpu state loaded")
Reported-by: Julien Grall <julien.grall@arm.com>
Tested-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 arch/arm64/kvm/reset.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/kvm/reset.c b/arch/arm64/kvm/reset.c
index f16a5f8ff2b4..e2a0500cd7a2 100644
--- a/arch/arm64/kvm/reset.c
+++ b/arch/arm64/kvm/reset.c
@@ -123,6 +123,9 @@ int kvm_reset_vcpu(struct kvm_vcpu *vcpu)
 	int ret = -EINVAL;
 	bool loaded;
 
+	/* Reset PMU outside of the non-preemptible section */
+	kvm_pmu_vcpu_reset(vcpu);
+
 	preempt_disable();
 	loaded = (vcpu->cpu != -1);
 	if (loaded)
@@ -170,9 +173,6 @@ int kvm_reset_vcpu(struct kvm_vcpu *vcpu)
 		vcpu->arch.reset_state.reset = false;
 	}
 
-	/* Reset PMU */
-	kvm_pmu_vcpu_reset(vcpu);
-
 	/* Default workaround setup is enabled (if supported) */
 	if (kvm_arm_have_ssbd() == KVM_SSBD_KERNEL)
 		vcpu->arch.workaround_flags |= VCPU_WORKAROUND_2_FLAG;
-- 
2.19.1

[PATCH AUTOSEL 5.0 26/98] arm64: KVM: Always set ICH_HCR_EL2.EN if GICv4 is enabled

[Sasha Levin]

From: Marc Zyngier <marc.zyngier@arm.com>

[ Upstream commit ca71228b42a96908eca7658861eafacd227856c9 ]

The normal interrupt flow is not to enable the vgic when no virtual
interrupt is to be injected (i.e. the LRs are empty). But when a guest
is likely to use GICv4 for LPIs, we absolutely need to switch it on
at all times. Otherwise, VLPIs only get delivered when there is something
in the LRs, which doesn't happen very often.

Reported-by: Nianyao Tang <tangnianyao@huawei.com>
Tested-by: Shameerali Kolothum Thodi <shameerali.kolothum.thodi@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 virt/kvm/arm/hyp/vgic-v3-sr.c |  4 ++--
 virt/kvm/arm/vgic/vgic.c      | 14 ++++++++++----
 2 files changed, 12 insertions(+), 6 deletions(-)

diff --git a/virt/kvm/arm/hyp/vgic-v3-sr.c b/virt/kvm/arm/hyp/vgic-v3-sr.c
index 9652c453480f..3c3f7cda95c7 100644
--- a/virt/kvm/arm/hyp/vgic-v3-sr.c
+++ b/virt/kvm/arm/hyp/vgic-v3-sr.c
@@ -222,7 +222,7 @@ void __hyp_text __vgic_v3_save_state(struct kvm_vcpu *vcpu)
 		}
 	}
 
-	if (used_lrs) {
+	if (used_lrs || cpu_if->its_vpe.its_vm) {
 		int i;
 		u32 elrsr;
 
@@ -247,7 +247,7 @@ void __hyp_text __vgic_v3_restore_state(struct kvm_vcpu *vcpu)
 	u64 used_lrs = vcpu->arch.vgic_cpu.used_lrs;
 	int i;
 
-	if (used_lrs) {
+	if (used_lrs || cpu_if->its_vpe.its_vm) {
 		write_gicreg(cpu_if->vgic_hcr, ICH_HCR_EL2);
 
 		for (i = 0; i < used_lrs; i++)
diff --git a/virt/kvm/arm/vgic/vgic.c b/virt/kvm/arm/vgic/vgic.c
index abd9c7352677..3af69f2a3866 100644
--- a/virt/kvm/arm/vgic/vgic.c
+++ b/virt/kvm/arm/vgic/vgic.c
@@ -867,15 +867,21 @@ void kvm_vgic_flush_hwstate(struct kvm_vcpu *vcpu)
 	 * either observe the new interrupt before or after doing this check,
 	 * and introducing additional synchronization mechanism doesn't change
 	 * this.
+	 *
+	 * Note that we still need to go through the whole thing if anything
+	 * can be directly injected (GICv4).
 	 */
-	if (list_empty(&vcpu->arch.vgic_cpu.ap_list_head))
+	if (list_empty(&vcpu->arch.vgic_cpu.ap_list_head) &&
+	    !vgic_supports_direct_msis(vcpu->kvm))
 		return;
 
 	DEBUG_SPINLOCK_BUG_ON(!irqs_disabled());
 
-	raw_spin_lock(&vcpu->arch.vgic_cpu.ap_list_lock);
-	vgic_flush_lr_state(vcpu);
-	raw_spin_unlock(&vcpu->arch.vgic_cpu.ap_list_lock);
+	if (!list_empty(&vcpu->arch.vgic_cpu.ap_list_head)) {
+		raw_spin_lock(&vcpu->arch.vgic_cpu.ap_list_lock);
+		vgic_flush_lr_state(vcpu);
+		raw_spin_unlock(&vcpu->arch.vgic_cpu.ap_list_lock);
+	}
 
 	if (can_access_vgic_from_kernel())
 		vgic_restore_state(vcpu);
-- 
2.19.1

[PATCH AUTOSEL 5.0 27/98] KVM: arm/arm64: vgic-its: Take the srcu lock when writing to guest memory

[Sasha Levin]

From: Marc Zyngier <marc.zyngier@arm.com>

[ Upstream commit a6ecfb11bf37743c1ac49b266595582b107b61d4 ]

When halting a guest, QEMU flushes the virtual ITS caches, which
amounts to writing to the various tables that the guest has allocated.

When doing this, we fail to take the srcu lock, and the kernel
shouts loudly if running a lockdep kernel:

[   69.680416] =============================
[   69.680819] WARNING: suspicious RCU usage
[   69.681526] 5.1.0-rc1-00008-g600025238f51-dirty #18 Not tainted
[   69.682096] -----------------------------
[   69.682501] ./include/linux/kvm_host.h:605 suspicious rcu_dereference_check() usage!
[   69.683225]
[   69.683225] other info that might help us debug this:
[   69.683225]
[   69.683975]
[   69.683975] rcu_scheduler_active = 2, debug_locks = 1
[   69.684598] 6 locks held by qemu-system-aar/4097:
[   69.685059]  #0: 0000000034196013 (&kvm->lock){+.+.}, at: vgic_its_set_attr+0x244/0x3a0
[   69.686087]  #1: 00000000f2ed935e (&its->its_lock){+.+.}, at: vgic_its_set_attr+0x250/0x3a0
[   69.686919]  #2: 000000005e71ea54 (&vcpu->mutex){+.+.}, at: lock_all_vcpus+0x64/0xd0
[   69.687698]  #3: 00000000c17e548d (&vcpu->mutex){+.+.}, at: lock_all_vcpus+0x64/0xd0
[   69.688475]  #4: 00000000ba386017 (&vcpu->mutex){+.+.}, at: lock_all_vcpus+0x64/0xd0
[   69.689978]  #5: 00000000c2c3c335 (&vcpu->mutex){+.+.}, at: lock_all_vcpus+0x64/0xd0
[   69.690729]
[   69.690729] stack backtrace:
[   69.691151] CPU: 2 PID: 4097 Comm: qemu-system-aar Not tainted 5.1.0-rc1-00008-g600025238f51-dirty #18
[   69.691984] Hardware name: rockchip evb_rk3399/evb_rk3399, BIOS 2019.04-rc3-00124-g2feec69fb1 03/15/2019
[   69.692831] Call trace:
[   69.694072]  lockdep_rcu_suspicious+0xcc/0x110
[   69.694490]  gfn_to_memslot+0x174/0x190
[   69.694853]  kvm_write_guest+0x50/0xb0
[   69.695209]  vgic_its_save_tables_v0+0x248/0x330
[   69.695639]  vgic_its_set_attr+0x298/0x3a0
[   69.696024]  kvm_device_ioctl_attr+0x9c/0xd8
[   69.696424]  kvm_device_ioctl+0x8c/0xf8
[   69.696788]  do_vfs_ioctl+0xc8/0x960
[   69.697128]  ksys_ioctl+0x8c/0xa0
[   69.697445]  __arm64_sys_ioctl+0x28/0x38
[   69.697817]  el0_svc_common+0xd8/0x138
[   69.698173]  el0_svc_handler+0x38/0x78
[   69.698528]  el0_svc+0x8/0xc

The fix is to obviously take the srcu lock, just like we do on the
read side of things since bf308242ab98. One wonders why this wasn't
fixed at the same time, but hey...

Fixes: bf308242ab98 ("KVM: arm/arm64: VGIC/ITS: protect kvm_read_guest() calls with SRCU lock")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 arch/arm/include/asm/kvm_mmu.h   | 11 +++++++++++
 arch/arm64/include/asm/kvm_mmu.h | 11 +++++++++++
 virt/kvm/arm/vgic/vgic-its.c     |  8 ++++----
 virt/kvm/arm/vgic/vgic-v3.c      |  4 ++--
 4 files changed, 28 insertions(+), 6 deletions(-)

diff --git a/arch/arm/include/asm/kvm_mmu.h b/arch/arm/include/asm/kvm_mmu.h
index 3a875fc1b63c..cee06509f00a 100644
--- a/arch/arm/include/asm/kvm_mmu.h
+++ b/arch/arm/include/asm/kvm_mmu.h
@@ -381,6 +381,17 @@ static inline int kvm_read_guest_lock(struct kvm *kvm,
 	return ret;
 }
 
+static inline int kvm_write_guest_lock(struct kvm *kvm, gpa_t gpa,
+				       const void *data, unsigned long len)
+{
+	int srcu_idx = srcu_read_lock(&kvm->srcu);
+	int ret = kvm_write_guest(kvm, gpa, data, len);
+
+	srcu_read_unlock(&kvm->srcu, srcu_idx);
+
+	return ret;
+}
+
 static inline void *kvm_get_hyp_vector(void)
 {
 	switch(read_cpuid_part()) {
diff --git a/arch/arm64/include/asm/kvm_mmu.h b/arch/arm64/include/asm/kvm_mmu.h
index 8af4b1befa42..c246effd1b67 100644
--- a/arch/arm64/include/asm/kvm_mmu.h
+++ b/arch/arm64/include/asm/kvm_mmu.h
@@ -444,6 +444,17 @@ static inline int kvm_read_guest_lock(struct kvm *kvm,
 	return ret;
 }
 
+static inline int kvm_write_guest_lock(struct kvm *kvm, gpa_t gpa,
+				       const void *data, unsigned long len)
+{
+	int srcu_idx = srcu_read_lock(&kvm->srcu);
+	int ret = kvm_write_guest(kvm, gpa, data, len);
+
+	srcu_read_unlock(&kvm->srcu, srcu_idx);
+
+	return ret;
+}
+
 #ifdef CONFIG_KVM_INDIRECT_VECTORS
 /*
  * EL2 vectors can be mapped and rerouted in a number of ways,
diff --git a/virt/kvm/arm/vgic/vgic-its.c b/virt/kvm/arm/vgic/vgic-its.c
index ab3f47745d9c..c41e11fd841c 100644
--- a/virt/kvm/arm/vgic/vgic-its.c
+++ b/virt/kvm/arm/vgic/vgic-its.c
@@ -1919,7 +1919,7 @@ static int vgic_its_save_ite(struct vgic_its *its, struct its_device *dev,
 	       ((u64)ite->irq->intid << KVM_ITS_ITE_PINTID_SHIFT) |
 		ite->collection->collection_id;
 	val = cpu_to_le64(val);
-	return kvm_write_guest(kvm, gpa, &val, ite_esz);
+	return kvm_write_guest_lock(kvm, gpa, &val, ite_esz);
 }
 
 /**
@@ -2066,7 +2066,7 @@ static int vgic_its_save_dte(struct vgic_its *its, struct its_device *dev,
 	       (itt_addr_field << KVM_ITS_DTE_ITTADDR_SHIFT) |
 		(dev->num_eventid_bits - 1));
 	val = cpu_to_le64(val);
-	return kvm_write_guest(kvm, ptr, &val, dte_esz);
+	return kvm_write_guest_lock(kvm, ptr, &val, dte_esz);
 }
 
 /**
@@ -2246,7 +2246,7 @@ static int vgic_its_save_cte(struct vgic_its *its,
 	       ((u64)collection->target_addr << KVM_ITS_CTE_RDBASE_SHIFT) |
 	       collection->collection_id);
 	val = cpu_to_le64(val);
-	return kvm_write_guest(its->dev->kvm, gpa, &val, esz);
+	return kvm_write_guest_lock(its->dev->kvm, gpa, &val, esz);
 }
 
 static int vgic_its_restore_cte(struct vgic_its *its, gpa_t gpa, int esz)
@@ -2317,7 +2317,7 @@ static int vgic_its_save_collection_table(struct vgic_its *its)
 	 */
 	val = 0;
 	BUG_ON(cte_esz > sizeof(val));
-	ret = kvm_write_guest(its->dev->kvm, gpa, &val, cte_esz);
+	ret = kvm_write_guest_lock(its->dev->kvm, gpa, &val, cte_esz);
 	return ret;
 }
 
diff --git a/virt/kvm/arm/vgic/vgic-v3.c b/virt/kvm/arm/vgic/vgic-v3.c
index 4ee0aeb9a905..89260964be73 100644
--- a/virt/kvm/arm/vgic/vgic-v3.c
+++ b/virt/kvm/arm/vgic/vgic-v3.c
@@ -358,7 +358,7 @@ retry:
 	if (status) {
 		/* clear consumed data */
 		val &= ~(1 << bit_nr);
-		ret = kvm_write_guest(kvm, ptr, &val, 1);
+		ret = kvm_write_guest_lock(kvm, ptr, &val, 1);
 		if (ret)
 			return ret;
 	}
@@ -409,7 +409,7 @@ int vgic_v3_save_pending_tables(struct kvm *kvm)
 		else
 			val &= ~(1 << bit_nr);
 
-		ret = kvm_write_guest(kvm, ptr, &val, 1);
+		ret = kvm_write_guest_lock(kvm, ptr, &val, 1);
 		if (ret)
 			return ret;
 	}
-- 
2.19.1

[PATCH AUTOSEL 5.0 28/98] KVM: arm/arm64: vgic-its: Take the srcu lock when parsing the memslots

[Sasha Levin]

From: Marc Zyngier <marc.zyngier@arm.com>

[ Upstream commit 7494cec6cb3ba7385a6a223b81906384f15aae34 ]

Calling kvm_is_visible_gfn() implies that we're parsing the memslots,
and doing this without the srcu lock is frown upon:

[12704.164532] =============================
[12704.164544] WARNING: suspicious RCU usage
[12704.164560] 5.1.0-rc1-00008-g600025238f51-dirty #16 Tainted: G        W
[12704.164573] -----------------------------
[12704.164589] ./include/linux/kvm_host.h:605 suspicious rcu_dereference_check() usage!
[12704.164602] other info that might help us debug this:
[12704.164616] rcu_scheduler_active = 2, debug_locks = 1
[12704.164631] 6 locks held by qemu-system-aar/13968:
[12704.164644]  #0: 000000007ebdae4f (&kvm->lock){+.+.}, at: vgic_its_set_attr+0x244/0x3a0
[12704.164691]  #1: 000000007d751022 (&its->its_lock){+.+.}, at: vgic_its_set_attr+0x250/0x3a0
[12704.164726]  #2: 00000000219d2706 (&vcpu->mutex){+.+.}, at: lock_all_vcpus+0x64/0xd0
[12704.164761]  #3: 00000000a760aecd (&vcpu->mutex){+.+.}, at: lock_all_vcpus+0x64/0xd0
[12704.164794]  #4: 000000000ef8e31d (&vcpu->mutex){+.+.}, at: lock_all_vcpus+0x64/0xd0
[12704.164827]  #5: 000000007a872093 (&vcpu->mutex){+.+.}, at: lock_all_vcpus+0x64/0xd0
[12704.164861] stack backtrace:
[12704.164878] CPU: 2 PID: 13968 Comm: qemu-system-aar Tainted: G        W         5.1.0-rc1-00008-g600025238f51-dirty #16
[12704.164887] Hardware name: rockchip evb_rk3399/evb_rk3399, BIOS 2019.04-rc3-00124-g2feec69fb1 03/15/2019
[12704.164896] Call trace:
[12704.164910]  dump_backtrace+0x0/0x138
[12704.164920]  show_stack+0x24/0x30
[12704.164934]  dump_stack+0xbc/0x104
[12704.164946]  lockdep_rcu_suspicious+0xcc/0x110
[12704.164958]  gfn_to_memslot+0x174/0x190
[12704.164969]  kvm_is_visible_gfn+0x28/0x70
[12704.164980]  vgic_its_check_id.isra.0+0xec/0x1e8
[12704.164991]  vgic_its_save_tables_v0+0x1ac/0x330
[12704.165001]  vgic_its_set_attr+0x298/0x3a0
[12704.165012]  kvm_device_ioctl_attr+0x9c/0xd8
[12704.165022]  kvm_device_ioctl+0x8c/0xf8
[12704.165035]  do_vfs_ioctl+0xc8/0x960
[12704.165045]  ksys_ioctl+0x8c/0xa0
[12704.165055]  __arm64_sys_ioctl+0x28/0x38
[12704.165067]  el0_svc_common+0xd8/0x138
[12704.165078]  el0_svc_handler+0x38/0x78
[12704.165089]  el0_svc+0x8/0xc

Make sure the lock is taken when doing this.

Fixes: bf308242ab98 ("KVM: arm/arm64: VGIC/ITS: protect kvm_read_guest() calls with SRCU lock")
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 virt/kvm/arm/vgic/vgic-its.c | 13 ++++++++++---
 1 file changed, 10 insertions(+), 3 deletions(-)

diff --git a/virt/kvm/arm/vgic/vgic-its.c b/virt/kvm/arm/vgic/vgic-its.c
index c41e11fd841c..fcb2fceaa4a5 100644
--- a/virt/kvm/arm/vgic/vgic-its.c
+++ b/virt/kvm/arm/vgic/vgic-its.c
@@ -754,8 +754,9 @@ static bool vgic_its_check_id(struct vgic_its *its, u64 baser, u32 id,
 	u64 indirect_ptr, type = GITS_BASER_TYPE(baser);
 	phys_addr_t base = GITS_BASER_ADDR_48_to_52(baser);
 	int esz = GITS_BASER_ENTRY_SIZE(baser);
-	int index;
+	int index, idx;
 	gfn_t gfn;
+	bool ret;
 
 	switch (type) {
 	case GITS_BASER_TYPE_DEVICE:
@@ -782,7 +783,8 @@ static bool vgic_its_check_id(struct vgic_its *its, u64 baser, u32 id,
 
 		if (eaddr)
 			*eaddr = addr;
-		return kvm_is_visible_gfn(its->dev->kvm, gfn);
+
+		goto out;
 	}
 
 	/* calculate and check the index into the 1st level */
@@ -812,7 +814,12 @@ static bool vgic_its_check_id(struct vgic_its *its, u64 baser, u32 id,
 
 	if (eaddr)
 		*eaddr = indirect_ptr;
-	return kvm_is_visible_gfn(its->dev->kvm, gfn);
+
+out:
+	idx = srcu_read_lock(&its->dev->kvm->srcu);
+	ret = kvm_is_visible_gfn(its->dev->kvm, gfn);
+	srcu_read_unlock(&its->dev->kvm->srcu, idx);
+	return ret;
 }
 
 static int vgic_its_alloc_collection(struct vgic_its *its,
-- 
2.19.1

[PATCH AUTOSEL 5.0 29/98] KVM: arm/arm64: Enforce PTE mappings at stage2 when needed

[Sasha Levin]

From: Suzuki K Poulose <suzuki.poulose@arm.com>

[ Upstream commit a80868f398554842b14d07060012c06efb57c456 ]

commit 6794ad5443a2118 ("KVM: arm/arm64: Fix unintended stage 2 PMD mappings")
made the checks to skip huge mappings, stricter. However it introduced
a bug where we still use huge mappings, ignoring the flag to
use PTE mappings, by not reseting the vma_pagesize to PAGE_SIZE.

Also, the checks do not cover the PUD huge pages, that was
under review during the same period. This patch fixes both
the issues.

Fixes : 6794ad5443a2118 ("KVM: arm/arm64: Fix unintended stage 2 PMD mappings")
Reported-by: Zenghui Yu <yuzenghui@huawei.com>
Cc: Zenghui Yu <yuzenghui@huawei.com>
Cc: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 virt/kvm/arm/mmu.c | 43 +++++++++++++++++++++----------------------
 1 file changed, 21 insertions(+), 22 deletions(-)

diff --git a/virt/kvm/arm/mmu.c b/virt/kvm/arm/mmu.c
index 5cc22cdaa5ba..6dccb36465e6 100644
--- a/virt/kvm/arm/mmu.c
+++ b/virt/kvm/arm/mmu.c
@@ -1595,8 +1595,9 @@ static void kvm_send_hwpoison_signal(unsigned long address,
 	send_sig_mceerr(BUS_MCEERR_AR, (void __user *)address, lsb, current);
 }
 
-static bool fault_supports_stage2_pmd_mappings(struct kvm_memory_slot *memslot,
-					       unsigned long hva)
+static bool fault_supports_stage2_huge_mapping(struct kvm_memory_slot *memslot,
+					       unsigned long hva,
+					       unsigned long map_size)
 {
 	gpa_t gpa_start, gpa_end;
 	hva_t uaddr_start, uaddr_end;
@@ -1612,34 +1613,34 @@ static bool fault_supports_stage2_pmd_mappings(struct kvm_memory_slot *memslot,
 
 	/*
 	 * Pages belonging to memslots that don't have the same alignment
-	 * within a PMD for userspace and IPA cannot be mapped with stage-2
-	 * PMD entries, because we'll end up mapping the wrong pages.
+	 * within a PMD/PUD for userspace and IPA cannot be mapped with stage-2
+	 * PMD/PUD entries, because we'll end up mapping the wrong pages.
 	 *
 	 * Consider a layout like the following:
 	 *
 	 *    memslot->userspace_addr:
 	 *    +-----+--------------------+--------------------+---+
-	 *    |abcde|fgh  Stage-1 PMD    |    Stage-1 PMD   tv|xyz|
+	 *    |abcde|fgh  Stage-1 block  |    Stage-1 block tv|xyz|
 	 *    +-----+--------------------+--------------------+---+
 	 *
 	 *    memslot->base_gfn << PAGE_SIZE:
 	 *      +---+--------------------+--------------------+-----+
-	 *      |abc|def  Stage-2 PMD    |    Stage-2 PMD     |tvxyz|
+	 *      |abc|def  Stage-2 block  |    Stage-2 block   |tvxyz|
 	 *      +---+--------------------+--------------------+-----+
 	 *
-	 * If we create those stage-2 PMDs, we'll end up with this incorrect
+	 * If we create those stage-2 blocks, we'll end up with this incorrect
 	 * mapping:
 	 *   d -> f
 	 *   e -> g
 	 *   f -> h
 	 */
-	if ((gpa_start & ~S2_PMD_MASK) != (uaddr_start & ~S2_PMD_MASK))
+	if ((gpa_start & (map_size - 1)) != (uaddr_start & (map_size - 1)))
 		return false;
 
 	/*
 	 * Next, let's make sure we're not trying to map anything not covered
-	 * by the memslot. This means we have to prohibit PMD size mappings
-	 * for the beginning and end of a non-PMD aligned and non-PMD sized
+	 * by the memslot. This means we have to prohibit block size mappings
+	 * for the beginning and end of a non-block aligned and non-block sized
 	 * memory slot (illustrated by the head and tail parts of the
 	 * userspace view above containing pages 'abcde' and 'xyz',
 	 * respectively).
@@ -1648,8 +1649,8 @@ static bool fault_supports_stage2_pmd_mappings(struct kvm_memory_slot *memslot,
 	 * userspace_addr or the base_gfn, as both are equally aligned (per
 	 * the check above) and equally sized.
 	 */
-	return (hva & S2_PMD_MASK) >= uaddr_start &&
-	       (hva & S2_PMD_MASK) + S2_PMD_SIZE <= uaddr_end;
+	return (hva & ~(map_size - 1)) >= uaddr_start &&
+	       (hva & ~(map_size - 1)) + map_size <= uaddr_end;
 }
 
 static int user_mem_abort(struct kvm_vcpu *vcpu, phys_addr_t fault_ipa,
@@ -1678,12 +1679,6 @@ static int user_mem_abort(struct kvm_vcpu *vcpu, phys_addr_t fault_ipa,
 		return -EFAULT;
 	}
 
-	if (!fault_supports_stage2_pmd_mappings(memslot, hva))
-		force_pte = true;
-
-	if (logging_active)
-		force_pte = true;
-
 	/* Let's check if we will get back a huge page backed by hugetlbfs */
 	down_read(&current->mm->mmap_sem);
 	vma = find_vma_intersection(current->mm, hva, hva + 1);
@@ -1694,6 +1689,12 @@ static int user_mem_abort(struct kvm_vcpu *vcpu, phys_addr_t fault_ipa,
 	}
 
 	vma_pagesize = vma_kernel_pagesize(vma);
+	if (logging_active ||
+	    !fault_supports_stage2_huge_mapping(memslot, hva, vma_pagesize)) {
+		force_pte = true;
+		vma_pagesize = PAGE_SIZE;
+	}
+
 	/*
 	 * The stage2 has a minimum of 2 level table (For arm64 see
 	 * kvm_arm_setup_stage2()). Hence, we are guaranteed that we can
@@ -1701,11 +1702,9 @@ static int user_mem_abort(struct kvm_vcpu *vcpu, phys_addr_t fault_ipa,
 	 * As for PUD huge maps, we must make sure that we have at least
 	 * 3 levels, i.e, PMD is not folded.
 	 */
-	if ((vma_pagesize == PMD_SIZE ||
-	     (vma_pagesize == PUD_SIZE && kvm_stage2_has_pmd(kvm))) &&
-	    !force_pte) {
+	if (vma_pagesize == PMD_SIZE ||
+	    (vma_pagesize == PUD_SIZE && kvm_stage2_has_pmd(kvm)))
 		gfn = (fault_ipa & huge_page_mask(hstate_vma(vma))) >> PAGE_SHIFT;
-	}
 	up_read(&current->mm->mmap_sem);
 
 	/* We need minimum second+third level pages */
-- 
2.19.1

[PATCH AUTOSEL 5.0 30/98] usb: dwc3: pci: add support for Comet Lake PCH ID

[Sasha Levin]

From: Felipe Balbi <felipe.balbi@linux.intel.com>

[ Upstream commit 7ae622c978db6b2e28b4fced6ecd2a174492059d ]

This patch simply adds a new PCI Device ID

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/usb/dwc3/dwc3-pci.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/usb/dwc3/dwc3-pci.c b/drivers/usb/dwc3/dwc3-pci.c
index fdc6e4e403e8..8cced3609e24 100644
--- a/drivers/usb/dwc3/dwc3-pci.c
+++ b/drivers/usb/dwc3/dwc3-pci.c
@@ -29,6 +29,7 @@
 #define PCI_DEVICE_ID_INTEL_BXT_M		0x1aaa
 #define PCI_DEVICE_ID_INTEL_APL			0x5aaa
 #define PCI_DEVICE_ID_INTEL_KBP			0xa2b0
+#define PCI_DEVICE_ID_INTEL_CMLH		0x02ee
 #define PCI_DEVICE_ID_INTEL_GLK			0x31aa
 #define PCI_DEVICE_ID_INTEL_CNPLP		0x9dee
 #define PCI_DEVICE_ID_INTEL_CNPH		0xa36e
@@ -305,6 +306,9 @@ static const struct pci_device_id dwc3_pci_id_table[] = {
 	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_MRFLD),
 	  (kernel_ulong_t) &dwc3_pci_mrfld_properties, },
 
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_CMLH),
+	  (kernel_ulong_t) &dwc3_pci_intel_properties, },
+
 	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_SPTLP),
 	  (kernel_ulong_t) &dwc3_pci_intel_properties, },
 
-- 
2.19.1

[PATCH AUTOSEL 5.0 31/98] usb: gadget: net2280: Fix overrun of OUT messages

[Sasha Levin]

From: Guido Kiener <guido@kiener-muenchen.de>

[ Upstream commit 9d6a54c1430647355a5e23434881b2ca3d192b48 ]

The OUT endpoint normally blocks (NAK) subsequent packets when a
short packet was received and returns an incomplete queue entry to
the gadget driver. Thereby the gadget driver can detect a short packet
when reading queue entries with a length that is not equal to a
multiple of packet size.

The start_queue() function enables receiving OUT packets regardless of
the content of the OUT FIFO. This results in a race: With the current
code, it's possible that the "!ep->is_in && (readl(&ep->regs->ep_stat)
& BIT(NAK_OUT_PACKETS))" test in start_dma() will fail, then a short
packet will be received, and then start_queue() will call
stop_out_naking(). That's what we don't want (OUT naking gets turned
off while there is data in the FIFO) because then the next driver
request might receive a mixture of old and new packets.

With the patch, this race can't occur because the FIFO's state is
tested after we know that OUT naking is already turned on, and OUT
naking is stopped only when both of the conditions are met.  This
ensures that all received data is delivered to the gadget driver,
which can detect a short packet now before new packets are appended
to the last short packet.

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/usb/gadget/udc/net2280.c | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)

diff --git a/drivers/usb/gadget/udc/net2280.c b/drivers/usb/gadget/udc/net2280.c
index e7dae5379e04..dc6f5a78d124 100644
--- a/drivers/usb/gadget/udc/net2280.c
+++ b/drivers/usb/gadget/udc/net2280.c
@@ -866,9 +866,6 @@ static void start_queue(struct net2280_ep *ep, u32 dmactl, u32 td_dma)
 	(void) readl(&ep->dev->pci->pcimstctl);
 
 	writel(BIT(DMA_START), &dma->dmastat);
-
-	if (!ep->is_in)
-		stop_out_naking(ep);
 }
 
 static void start_dma(struct net2280_ep *ep, struct net2280_request *req)
@@ -907,6 +904,7 @@ static void start_dma(struct net2280_ep *ep, struct net2280_request *req)
 			writel(BIT(DMA_START), &dma->dmastat);
 			return;
 		}
+		stop_out_naking(ep);
 	}
 
 	tmp = dmactl_default;
-- 
2.19.1

[PATCH AUTOSEL 5.0 32/98] usb: gadget: net2280: Fix net2280_dequeue()

[Sasha Levin]

From: Guido Kiener <guido@kiener-muenchen.de>

[ Upstream commit f1d3fba17cd4eeea20397f1324b7b9c69a6a935c ]

When a request must be dequeued with net2280_dequeue() e.g. due
to a device clear action and the same request is finished by the
function scan_dma_completions() then the function net2280_dequeue()
does not find the request in the following search loop and
returns the error -EINVAL without restoring the status ep->stopped.
Thus the endpoint keeps blocked and does not receive any data
anymore.
This fix restores the status and does not issue an error message.

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/usb/gadget/udc/net2280.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/usb/gadget/udc/net2280.c b/drivers/usb/gadget/udc/net2280.c
index dc6f5a78d124..d93cf4171953 100644
--- a/drivers/usb/gadget/udc/net2280.c
+++ b/drivers/usb/gadget/udc/net2280.c
@@ -1273,9 +1273,9 @@ static int net2280_dequeue(struct usb_ep *_ep, struct usb_request *_req)
 			break;
 	}
 	if (&req->req != _req) {
+		ep->stopped = stopped;
 		spin_unlock_irqrestore(&ep->dev->lock, flags);
-		dev_err(&ep->dev->pdev->dev, "%s: Request mismatch\n",
-								__func__);
+		ep_dbg(ep->dev, "%s: Request mismatch\n", __func__);
 		return -EINVAL;
 	}
 
-- 
2.19.1

[PATCH AUTOSEL 5.0 33/98] usb: gadget: net2272: Fix net2272_dequeue()

[Sasha Levin]

From: Guido Kiener <guido@kiener-muenchen.de>

[ Upstream commit 091dacc3cc10979ab0422f0a9f7fcc27eee97e69 ]

Restore the status of ep->stopped in function net2272_dequeue().

When the given request is not found in the endpoint queue
the function returns -EINVAL without restoring the state of
ep->stopped. Thus the endpoint keeps blocked and does not transfer
any data anymore.

This fix is only compile-tested, since we do not have a
corresponding hardware. An analogous fix was tested in the sibling
driver. See "usb: gadget: net2280: Fix net2280_dequeue()"

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/usb/gadget/udc/net2272.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/usb/gadget/udc/net2272.c b/drivers/usb/gadget/udc/net2272.c
index b77f3126580e..c2011cd7df8c 100644
--- a/drivers/usb/gadget/udc/net2272.c
+++ b/drivers/usb/gadget/udc/net2272.c
@@ -945,6 +945,7 @@ net2272_dequeue(struct usb_ep *_ep, struct usb_request *_req)
 			break;
 	}
 	if (&req->req != _req) {
+		ep->stopped = stopped;
 		spin_unlock_irqrestore(&ep->dev->lock, flags);
 		return -EINVAL;
 	}
-- 
2.19.1

[PATCH AUTOSEL 5.0 34/98] ARM: dts: pfla02: increase phy reset duration

[Sasha Levin]

From: Marco Felsch <m.felsch@pengutronix.de>

[ Upstream commit 032f85c9360fb1a08385c584c2c4ed114b33c260 ]

Increase the reset duration to ensure correct phy functionality. The
reset duration is taken from barebox commit 52fdd510de ("ARM: dts:
pfla02: use long enough reset for ethernet phy"):

  Use a longer reset time for ethernet phy Micrel KSZ9031RNX. Otherwise a
  small percentage of modules have 'transmission timeouts' errors like

  barebox@Phytec phyFLEX-i.MX6 Quad Carrier-Board:/ ifup eth0
  warning: No MAC address set. Using random address 7e:94:4d:02:f8:f3
  eth0: 1000Mbps full duplex link detected
  eth0: transmission timeout
  T eth0: transmission timeout
  T eth0: transmission timeout
  T eth0: transmission timeout
  T eth0: transmission timeout

Cc: Stefan Christ <s.christ@phytec.de>
Cc: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Fixes: 3180f956668e ("ARM: dts: Phytec imx6q pfla02 and pbab01 support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi
index 1b50b01e9bac..65d03c5d409b 100644
--- a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi
@@ -90,6 +90,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
+	phy-reset-duration = <10>; /* in msecs */
 	phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
 	phy-supply = <&vdd_eth_io_reg>;
 	status = "disabled";
-- 
2.19.1

[PATCH AUTOSEL 5.0 35/98] i2c: i801: Add support for Intel Comet Lake

[Sasha Levin]

From: Jarkko Nikula <jarkko.nikula@linux.intel.com>

[ Upstream commit 5cd1c56c42beb6d228cc8d4373fdc5f5ec78a5ad ]

Add PCI ID for Intel Comet Lake PCH.

Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 Documentation/i2c/busses/i2c-i801 | 1 +
 drivers/i2c/busses/Kconfig        | 1 +
 drivers/i2c/busses/i2c-i801.c     | 4 ++++
 3 files changed, 6 insertions(+)

diff --git a/Documentation/i2c/busses/i2c-i801 b/Documentation/i2c/busses/i2c-i801
index d1ee484a787d..ee9984f35868 100644
--- a/Documentation/i2c/busses/i2c-i801
+++ b/Documentation/i2c/busses/i2c-i801
@@ -36,6 +36,7 @@ Supported adapters:
   * Intel Cannon Lake (PCH)
   * Intel Cedar Fork (PCH)
   * Intel Ice Lake (PCH)
+  * Intel Comet Lake (PCH)
    Datasheets: Publicly available at the Intel website
 
 On Intel Patsburg and later chipsets, both the normal host SMBus controller
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index f2c681971201..f8979abb9a19 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -131,6 +131,7 @@ config I2C_I801
 	    Cannon Lake (PCH)
 	    Cedar Fork (PCH)
 	    Ice Lake (PCH)
+	    Comet Lake (PCH)
 
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-i801.
diff --git a/drivers/i2c/busses/i2c-i801.c b/drivers/i2c/busses/i2c-i801.c
index c91e145ef5a5..679c6c41f64b 100644
--- a/drivers/i2c/busses/i2c-i801.c
+++ b/drivers/i2c/busses/i2c-i801.c
@@ -71,6 +71,7 @@
  * Cannon Lake-LP (PCH)		0x9da3	32	hard	yes	yes	yes
  * Cedar Fork (PCH)		0x18df	32	hard	yes	yes	yes
  * Ice Lake-LP (PCH)		0x34a3	32	hard	yes	yes	yes
+ * Comet Lake (PCH)		0x02a3	32	hard	yes	yes	yes
  *
  * Features supported by this driver:
  * Software PEC				no
@@ -240,6 +241,7 @@
 #define PCI_DEVICE_ID_INTEL_LEWISBURG_SSKU_SMBUS	0xa223
 #define PCI_DEVICE_ID_INTEL_KABYLAKE_PCH_H_SMBUS	0xa2a3
 #define PCI_DEVICE_ID_INTEL_CANNONLAKE_H_SMBUS		0xa323
+#define PCI_DEVICE_ID_INTEL_COMETLAKE_SMBUS		0x02a3
 
 struct i801_mux_config {
 	char *gpio_chip;
@@ -1038,6 +1040,7 @@ static const struct pci_device_id i801_ids[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_CANNONLAKE_H_SMBUS) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_CANNONLAKE_LP_SMBUS) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICELAKE_LP_SMBUS) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_COMETLAKE_SMBUS) },
 	{ 0, }
 };
 
@@ -1534,6 +1537,7 @@ static int i801_probe(struct pci_dev *dev, const struct pci_device_id *id)
 	case PCI_DEVICE_ID_INTEL_DNV_SMBUS:
 	case PCI_DEVICE_ID_INTEL_KABYLAKE_PCH_H_SMBUS:
 	case PCI_DEVICE_ID_INTEL_ICELAKE_LP_SMBUS:
+	case PCI_DEVICE_ID_INTEL_COMETLAKE_SMBUS:
 		priv->features |= FEATURE_I2C_BLOCK_READ;
 		priv->features |= FEATURE_IRQ;
 		priv->features |= FEATURE_SMBUS_PEC;
-- 
2.19.1

[PATCH AUTOSEL 5.0 36/98] KVM: arm/arm64: Fix handling of stage2 huge mappings

[Sasha Levin]

From: Suzuki K Poulose <suzuki.poulose@arm.com>

[ Upstream commit 3c3736cd32bf5197aed1410ae826d2d254a5b277 ]

We rely on the mmu_notifier call backs to handle the split/merge
of huge pages and thus we are guaranteed that, while creating a
block mapping, either the entire block is unmapped at stage2 or it
is missing permission.

However, we miss a case where the block mapping is split for dirty
logging case and then could later be made block mapping, if we cancel the
dirty logging. This not only creates inconsistent TLB entries for
the pages in the the block, but also leakes the table pages for
PMD level.

Handle this corner case for the huge mappings at stage2 by
unmapping the non-huge mapping for the block. This could potentially
release the upper level table. So we need to restart the table walk
once we unmap the range.

Fixes : ad361f093c1e31d ("KVM: ARM: Support hugetlbfs backed huge pages")
Reported-by: Zheng Xiang <zhengxiang9@huawei.com>
Cc: Zheng Xiang <zhengxiang9@huawei.com>
Cc: Zenghui Yu <yuzenghui@huawei.com>
Cc: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 arch/arm/include/asm/stage2_pgtable.h |  2 +
 virt/kvm/arm/mmu.c                    | 59 +++++++++++++++++++--------
 2 files changed, 45 insertions(+), 16 deletions(-)

diff --git a/arch/arm/include/asm/stage2_pgtable.h b/arch/arm/include/asm/stage2_pgtable.h
index de2089501b8b..9e11dce55e06 100644
--- a/arch/arm/include/asm/stage2_pgtable.h
+++ b/arch/arm/include/asm/stage2_pgtable.h
@@ -75,6 +75,8 @@ static inline bool kvm_stage2_has_pud(struct kvm *kvm)
 
 #define S2_PMD_MASK				PMD_MASK
 #define S2_PMD_SIZE				PMD_SIZE
+#define S2_PUD_MASK				PUD_MASK
+#define S2_PUD_SIZE				PUD_SIZE
 
 static inline bool kvm_stage2_has_pmd(struct kvm *kvm)
 {
diff --git a/virt/kvm/arm/mmu.c b/virt/kvm/arm/mmu.c
index 6dccb36465e6..7a0f9eeea68c 100644
--- a/virt/kvm/arm/mmu.c
+++ b/virt/kvm/arm/mmu.c
@@ -1060,25 +1060,43 @@ static int stage2_set_pmd_huge(struct kvm *kvm, struct kvm_mmu_memory_cache
 {
 	pmd_t *pmd, old_pmd;
 
+retry:
 	pmd = stage2_get_pmd(kvm, cache, addr);
 	VM_BUG_ON(!pmd);
 
 	old_pmd = *pmd;
+	/*
+	 * Multiple vcpus faulting on the same PMD entry, can
+	 * lead to them sequentially updating the PMD with the
+	 * same value. Following the break-before-make
+	 * (pmd_clear() followed by tlb_flush()) process can
+	 * hinder forward progress due to refaults generated
+	 * on missing translations.
+	 *
+	 * Skip updating the page table if the entry is
+	 * unchanged.
+	 */
+	if (pmd_val(old_pmd) == pmd_val(*new_pmd))
+		return 0;
+
 	if (pmd_present(old_pmd)) {
 		/*
-		 * Multiple vcpus faulting on the same PMD entry, can
-		 * lead to them sequentially updating the PMD with the
-		 * same value. Following the break-before-make
-		 * (pmd_clear() followed by tlb_flush()) process can
-		 * hinder forward progress due to refaults generated
-		 * on missing translations.
+		 * If we already have PTE level mapping for this block,
+		 * we must unmap it to avoid inconsistent TLB state and
+		 * leaking the table page. We could end up in this situation
+		 * if the memory slot was marked for dirty logging and was
+		 * reverted, leaving PTE level mappings for the pages accessed
+		 * during the period. So, unmap the PTE level mapping for this
+		 * block and retry, as we could have released the upper level
+		 * table in the process.
 		 *
-		 * Skip updating the page table if the entry is
-		 * unchanged.
+		 * Normal THP split/merge follows mmu_notifier callbacks and do
+		 * get handled accordingly.
 		 */
-		if (pmd_val(old_pmd) == pmd_val(*new_pmd))
-			return 0;
-
+		if (!pmd_thp_or_huge(old_pmd)) {
+			unmap_stage2_range(kvm, addr & S2_PMD_MASK, S2_PMD_SIZE);
+			goto retry;
+		}
 		/*
 		 * Mapping in huge pages should only happen through a
 		 * fault.  If a page is merged into a transparent huge
@@ -1090,8 +1108,7 @@ static int stage2_set_pmd_huge(struct kvm *kvm, struct kvm_mmu_memory_cache
 		 * should become splitting first, unmapped, merged,
 		 * and mapped back in on-demand.
 		 */
-		VM_BUG_ON(pmd_pfn(old_pmd) != pmd_pfn(*new_pmd));
-
+		WARN_ON_ONCE(pmd_pfn(old_pmd) != pmd_pfn(*new_pmd));
 		pmd_clear(pmd);
 		kvm_tlb_flush_vmid_ipa(kvm, addr);
 	} else {
@@ -1107,6 +1124,7 @@ static int stage2_set_pud_huge(struct kvm *kvm, struct kvm_mmu_memory_cache *cac
 {
 	pud_t *pudp, old_pud;
 
+retry:
 	pudp = stage2_get_pud(kvm, cache, addr);
 	VM_BUG_ON(!pudp);
 
@@ -1114,14 +1132,23 @@ static int stage2_set_pud_huge(struct kvm *kvm, struct kvm_mmu_memory_cache *cac
 
 	/*
 	 * A large number of vcpus faulting on the same stage 2 entry,
-	 * can lead to a refault due to the
-	 * stage2_pud_clear()/tlb_flush(). Skip updating the page
-	 * tables if there is no change.
+	 * can lead to a refault due to the stage2_pud_clear()/tlb_flush().
+	 * Skip updating the page tables if there is no change.
 	 */
 	if (pud_val(old_pud) == pud_val(*new_pudp))
 		return 0;
 
 	if (stage2_pud_present(kvm, old_pud)) {
+		/*
+		 * If we already have table level mapping for this block, unmap
+		 * the range for this block and retry.
+		 */
+		if (!stage2_pud_huge(kvm, old_pud)) {
+			unmap_stage2_range(kvm, addr & S2_PUD_MASK, S2_PUD_SIZE);
+			goto retry;
+		}
+
+		WARN_ON_ONCE(kvm_pud_pfn(old_pud) != kvm_pud_pfn(*new_pudp));
 		stage2_pud_clear(kvm, pudp);
 		kvm_tlb_flush_vmid_ipa(kvm, addr);
 	} else {
-- 
2.19.1

[PATCH AUTOSEL 5.0 37/98] net: ks8851: Dequeue RX packets explicitly

[Sasha Levin]

From: Lukas Wunner <lukas@wunner.de>

[ Upstream commit 536d3680fd2dab5c39857d62a3e084198fc74ff9 ]

The ks8851 driver lets the chip auto-dequeue received packets once they
have been read in full. It achieves that by setting the ADRFE flag in
the RXQCR register ("Auto-Dequeue RXQ Frame Enable").

However if allocation of a packet's socket buffer or retrieval of the
packet over the SPI bus fails, the packet will not have been read in
full and is not auto-dequeued. Such partial retrieval of a packet
confuses the chip's RX queue management:  On the next RX interrupt,
the first packet read from the queue will be the one left there
previously and this one can be retrieved without issues. But for any
newly received packets, the frame header status and byte count registers
(RXFHSR and RXFHBCR) contain bogus values, preventing their retrieval.

The chip allows explicitly dequeueing a packet from the RX queue by
setting the RRXEF flag in the RXQCR register ("Release RX Error Frame").
This could be used to dequeue the packet in case of an error, but if
that error is a failed SPI transfer, it is unknown if the packet was
transferred in full and was auto-dequeued or if it was only transferred
in part and requires an explicit dequeue. The safest approach is thus
to always dequeue packets explicitly and forgo auto-dequeueing.

Without this change, I've witnessed packet retrieval break completely
when an SPI DMA transfer fails, requiring a chip reset. Explicit
dequeueing magically fixes this and makes packet retrieval absolutely
robust for me.

The chip's documentation suggests auto-dequeuing and uses the RRXEF
flag only to dequeue error frames which the driver doesn't want to
retrieve. But that seems to be a fair-weather approach.

Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/net/ethernet/micrel/ks8851.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/micrel/ks8851.c b/drivers/net/ethernet/micrel/ks8851.c
index bd6e9014bc74..a93f8e842c07 100644
--- a/drivers/net/ethernet/micrel/ks8851.c
+++ b/drivers/net/ethernet/micrel/ks8851.c
@@ -535,9 +535,8 @@ static void ks8851_rx_pkts(struct ks8851_net *ks)
 		/* set dma read address */
 		ks8851_wrreg16(ks, KS_RXFDPR, RXFDPR_RXFPAI | 0x00);
 
-		/* start the packet dma process, and set auto-dequeue rx */
-		ks8851_wrreg16(ks, KS_RXQCR,
-			       ks->rc_rxqcr | RXQCR_SDA | RXQCR_ADRFE);
+		/* start DMA access */
+		ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr | RXQCR_SDA);
 
 		if (rxlen > 4) {
 			unsigned int rxalign;
@@ -568,7 +567,8 @@ static void ks8851_rx_pkts(struct ks8851_net *ks)
 			}
 		}
 
-		ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr);
+		/* end DMA access and dequeue packet */
+		ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr | RXQCR_RRXEF);
 	}
 }
 
-- 
2.19.1

[PATCH AUTOSEL 5.0 38/98] net: ks8851: Reassert reset pin if chip ID check fails

[Sasha Levin]

From: Lukas Wunner <lukas@wunner.de>

[ Upstream commit 761cfa979a0c177d6c2d93ef5585cd79ae49a7d5 ]

Commit 73fdeb82e963 ("net: ks8851: Add optional vdd_io regulator and
reset gpio") amended the ks8851 driver to briefly assert the chip's
reset pin on probe. It also amended the probe routine's error path to
reassert the reset pin if a subsequent initialization step fails.

However the commit misplaced reassertion of the reset pin in the error
path such that it is not performed if the check of the Chip ID and
Enable Register (CIDER) fails. The error path is therefore slightly
asymmetrical to the probe routine's body. Fix it.

Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/net/ethernet/micrel/ks8851.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/micrel/ks8851.c b/drivers/net/ethernet/micrel/ks8851.c
index a93f8e842c07..1633fa5c709c 100644
--- a/drivers/net/ethernet/micrel/ks8851.c
+++ b/drivers/net/ethernet/micrel/ks8851.c
@@ -1554,9 +1554,9 @@ err_netdev:
 	free_irq(ndev->irq, ks);
 
 err_irq:
+err_id:
 	if (gpio_is_valid(gpio))
 		gpio_set_value(gpio, 0);
-err_id:
 	regulator_disable(ks->vdd_reg);
 err_reg:
 	regulator_disable(ks->vdd_io);
-- 
2.19.1

[PATCH AUTOSEL 5.0 39/98] net: ks8851: Delay requesting IRQ until opened

[Sasha Levin]

From: Lukas Wunner <lukas@wunner.de>

[ Upstream commit d268f31552794abf5b6aa5af31021643411f25f5 ]

The ks8851 driver currently requests the IRQ before registering the
net_device.  Because the net_device name is used as IRQ name and is
still "eth%d" when the IRQ is requested, it's impossibe to tell IRQs
apart if multiple ks8851 chips are present.  Most other drivers delay
requesting the IRQ until the net_device is opened.  Do the same.

The driver doesn't enable interrupts on the chip before opening the
net_device and disables them when closing it, so there doesn't seem to
be a need to request the IRQ already on probe.

Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/net/ethernet/micrel/ks8851.c | 24 +++++++++++-------------
 1 file changed, 11 insertions(+), 13 deletions(-)

diff --git a/drivers/net/ethernet/micrel/ks8851.c b/drivers/net/ethernet/micrel/ks8851.c
index 1633fa5c709c..c9faec4c5b25 100644
--- a/drivers/net/ethernet/micrel/ks8851.c
+++ b/drivers/net/ethernet/micrel/ks8851.c
@@ -785,6 +785,15 @@ static void ks8851_tx_work(struct work_struct *work)
 static int ks8851_net_open(struct net_device *dev)
 {
 	struct ks8851_net *ks = netdev_priv(dev);
+	int ret;
+
+	ret = request_threaded_irq(dev->irq, NULL, ks8851_irq,
+				   IRQF_TRIGGER_LOW | IRQF_ONESHOT,
+				   dev->name, ks);
+	if (ret < 0) {
+		netdev_err(dev, "failed to get irq\n");
+		return ret;
+	}
 
 	/* lock the card, even if we may not actually be doing anything
 	 * else at the moment */
@@ -899,6 +908,8 @@ static int ks8851_net_stop(struct net_device *dev)
 		dev_kfree_skb(txb);
 	}
 
+	free_irq(dev->irq, ks);
+
 	return 0;
 }
 
@@ -1529,14 +1540,6 @@ static int ks8851_probe(struct spi_device *spi)
 	ks8851_read_selftest(ks);
 	ks8851_init_mac(ks);
 
-	ret = request_threaded_irq(spi->irq, NULL, ks8851_irq,
-				   IRQF_TRIGGER_LOW | IRQF_ONESHOT,
-				   ndev->name, ks);
-	if (ret < 0) {
-		dev_err(&spi->dev, "failed to get irq\n");
-		goto err_irq;
-	}
-
 	ret = register_netdev(ndev);
 	if (ret) {
 		dev_err(&spi->dev, "failed to register network device\n");
@@ -1549,11 +1552,7 @@ static int ks8851_probe(struct spi_device *spi)
 
 	return 0;
 
-
 err_netdev:
-	free_irq(ndev->irq, ks);
-
-err_irq:
 err_id:
 	if (gpio_is_valid(gpio))
 		gpio_set_value(gpio, 0);
@@ -1574,7 +1573,6 @@ static int ks8851_remove(struct spi_device *spi)
 		dev_info(&spi->dev, "remove\n");
 
 	unregister_netdev(priv->netdev);
-	free_irq(spi->irq, priv);
 	if (gpio_is_valid(priv->gpio))
 		gpio_set_value(priv->gpio, 0);
 	regulator_disable(priv->vdd_reg);
-- 
2.19.1

[PATCH AUTOSEL 5.0 40/98] net: ks8851: Set initial carrier state to down

[Sasha Levin]

From: Lukas Wunner <lukas@wunner.de>

[ Upstream commit 9624bafa5f6418b9ca5b3f66d1f6a6a2e8bf6d4c ]

The ks8851 chip's initial carrier state is down. A Link Change Interrupt
is signaled once interrupts are enabled if the carrier is up.

The ks8851 driver has it backwards by assuming that the initial carrier
state is up. The state is therefore misrepresented if the interface is
opened with no cable attached. Fix it.

The Link Change interrupt is sometimes not signaled unless the P1MBSR
register (which contains the Link Status bit) is read on ->ndo_open().
This might be a hardware erratum. Read the register by calling
mii_check_link(), which has the desirable side effect of setting the
carrier state to down if the cable was detached while the interface was
closed.

Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/net/ethernet/micrel/ks8851.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/net/ethernet/micrel/ks8851.c b/drivers/net/ethernet/micrel/ks8851.c
index c9faec4c5b25..b83b070a9eec 100644
--- a/drivers/net/ethernet/micrel/ks8851.c
+++ b/drivers/net/ethernet/micrel/ks8851.c
@@ -858,6 +858,7 @@ static int ks8851_net_open(struct net_device *dev)
 	netif_dbg(ks, ifup, ks->netdev, "network device up\n");
 
 	mutex_unlock(&ks->lock);
+	mii_check_link(&ks->mii);
 	return 0;
 }
 
@@ -1519,6 +1520,7 @@ static int ks8851_probe(struct spi_device *spi)
 
 	spi_set_drvdata(spi, ks);
 
+	netif_carrier_off(ks->netdev);
 	ndev->if_port = IF_PORT_100BASET;
 	ndev->netdev_ops = &ks8851_netdev_ops;
 	ndev->irq = spi->irq;
-- 
2.19.1

[PATCH AUTOSEL 5.0 41/98] staging: rtl8188eu: Fix potential NULL pointer dereference of kcalloc

[Sasha Levin]

From: Aditya Pakki <pakki001@umn.edu>

[ Upstream commit 7671ce0d92933762f469266daf43bd34d422d58c ]

hwxmits is allocated via kcalloc and not checked for failure before its
dereference. The patch fixes this problem by returning error upstream
in rtl8723bs, rtl8188eu.

Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Acked-by: Mukesh Ojha <mojha@codeaurora.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/staging/rtl8188eu/core/rtw_xmit.c    |  9 +++++++--
 drivers/staging/rtl8188eu/include/rtw_xmit.h |  2 +-
 drivers/staging/rtl8723bs/core/rtw_xmit.c    | 14 +++++++-------
 drivers/staging/rtl8723bs/include/rtw_xmit.h |  2 +-
 4 files changed, 16 insertions(+), 11 deletions(-)

diff --git a/drivers/staging/rtl8188eu/core/rtw_xmit.c b/drivers/staging/rtl8188eu/core/rtw_xmit.c
index 3b1ccd138c3f..6fb6ea29a8b6 100644
--- a/drivers/staging/rtl8188eu/core/rtw_xmit.c
+++ b/drivers/staging/rtl8188eu/core/rtw_xmit.c
@@ -174,7 +174,9 @@ s32 _rtw_init_xmit_priv(struct xmit_priv *pxmitpriv, struct adapter *padapter)
 
 	pxmitpriv->free_xmit_extbuf_cnt = num_xmit_extbuf;
 
-	rtw_alloc_hwxmits(padapter);
+	res = rtw_alloc_hwxmits(padapter);
+	if (res == _FAIL)
+		goto exit;
 	rtw_init_hwxmits(pxmitpriv->hwxmits, pxmitpriv->hwxmit_entry);
 
 	for (i = 0; i < 4; i++)
@@ -1503,7 +1505,7 @@ exit:
 	return res;
 }
 
-void rtw_alloc_hwxmits(struct adapter *padapter)
+s32 rtw_alloc_hwxmits(struct adapter *padapter)
 {
 	struct hw_xmit *hwxmits;
 	struct xmit_priv *pxmitpriv = &padapter->xmitpriv;
@@ -1512,6 +1514,8 @@ void rtw_alloc_hwxmits(struct adapter *padapter)
 
 	pxmitpriv->hwxmits = kcalloc(pxmitpriv->hwxmit_entry,
 				     sizeof(struct hw_xmit), GFP_KERNEL);
+	if (!pxmitpriv->hwxmits)
+		return _FAIL;
 
 	hwxmits = pxmitpriv->hwxmits;
 
@@ -1519,6 +1523,7 @@ void rtw_alloc_hwxmits(struct adapter *padapter)
 	hwxmits[1] .sta_queue = &pxmitpriv->vi_pending;
 	hwxmits[2] .sta_queue = &pxmitpriv->be_pending;
 	hwxmits[3] .sta_queue = &pxmitpriv->bk_pending;
+	return _SUCCESS;
 }
 
 void rtw_free_hwxmits(struct adapter *padapter)
diff --git a/drivers/staging/rtl8188eu/include/rtw_xmit.h b/drivers/staging/rtl8188eu/include/rtw_xmit.h
index 788f59c74ea1..ba7e15fbde72 100644
--- a/drivers/staging/rtl8188eu/include/rtw_xmit.h
+++ b/drivers/staging/rtl8188eu/include/rtw_xmit.h
@@ -336,7 +336,7 @@ s32 rtw_txframes_sta_ac_pending(struct adapter *padapter,
 void rtw_init_hwxmits(struct hw_xmit *phwxmit, int entry);
 s32 _rtw_init_xmit_priv(struct xmit_priv *pxmitpriv, struct adapter *padapter);
 void _rtw_free_xmit_priv(struct xmit_priv *pxmitpriv);
-void rtw_alloc_hwxmits(struct adapter *padapter);
+s32 rtw_alloc_hwxmits(struct adapter *padapter);
 void rtw_free_hwxmits(struct adapter *padapter);
 s32 rtw_xmit(struct adapter *padapter, struct sk_buff **pkt);
 
diff --git a/drivers/staging/rtl8723bs/core/rtw_xmit.c b/drivers/staging/rtl8723bs/core/rtw_xmit.c
index 625e67f39889..a36b2213d8ee 100644
--- a/drivers/staging/rtl8723bs/core/rtw_xmit.c
+++ b/drivers/staging/rtl8723bs/core/rtw_xmit.c
@@ -260,7 +260,9 @@ s32 _rtw_init_xmit_priv(struct xmit_priv *pxmitpriv, struct adapter *padapter)
 		}
 	}
 
-	rtw_alloc_hwxmits(padapter);
+	res = rtw_alloc_hwxmits(padapter);
+	if (res == _FAIL)
+		goto exit;
 	rtw_init_hwxmits(pxmitpriv->hwxmits, pxmitpriv->hwxmit_entry);
 
 	for (i = 0; i < 4; i++) {
@@ -2144,7 +2146,7 @@ exit:
 	return res;
 }
 
-void rtw_alloc_hwxmits(struct adapter *padapter)
+s32 rtw_alloc_hwxmits(struct adapter *padapter)
 {
 	struct hw_xmit *hwxmits;
 	struct xmit_priv *pxmitpriv = &padapter->xmitpriv;
@@ -2155,10 +2157,8 @@ void rtw_alloc_hwxmits(struct adapter *padapter)
 
 	pxmitpriv->hwxmits = rtw_zmalloc(sizeof(struct hw_xmit) * pxmitpriv->hwxmit_entry);
 
-	if (pxmitpriv->hwxmits == NULL) {
-		DBG_871X("alloc hwxmits fail!...\n");
-		return;
-	}
+	if (!pxmitpriv->hwxmits)
+		return _FAIL;
 
 	hwxmits = pxmitpriv->hwxmits;
 
@@ -2204,7 +2204,7 @@ void rtw_alloc_hwxmits(struct adapter *padapter)
 
 	}
 
-
+	return _SUCCESS;
 }
 
 void rtw_free_hwxmits(struct adapter *padapter)
diff --git a/drivers/staging/rtl8723bs/include/rtw_xmit.h b/drivers/staging/rtl8723bs/include/rtw_xmit.h
index 1b38b9182b31..37f42b2f22f1 100644
--- a/drivers/staging/rtl8723bs/include/rtw_xmit.h
+++ b/drivers/staging/rtl8723bs/include/rtw_xmit.h
@@ -487,7 +487,7 @@ s32 _rtw_init_xmit_priv(struct xmit_priv *pxmitpriv, struct adapter *padapter);
 void _rtw_free_xmit_priv (struct xmit_priv *pxmitpriv);
 
 
-void rtw_alloc_hwxmits(struct adapter *padapter);
+s32 rtw_alloc_hwxmits(struct adapter *padapter);
 void rtw_free_hwxmits(struct adapter *padapter);
 
 
-- 
2.19.1

[PATCH AUTOSEL 5.0 42/98] staging: rtlwifi: rtl8822b: fix to avoid potential NULL pointer dereference

[Sasha Levin]

From: Aditya Pakki <pakki001@umn.edu>

[ Upstream commit d70d70aec9632679dd00dcc1b1e8b2517e2c7da0 ]

skb allocated via dev_alloc_skb can fail and return a NULL pointer.
This patch avoids such a scenario and returns, consistent with other
invocations.

Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/staging/rtlwifi/rtl8822be/fw.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/staging/rtlwifi/rtl8822be/fw.c b/drivers/staging/rtlwifi/rtl8822be/fw.c
index a40396614814..c1ed52df05f0 100644
--- a/drivers/staging/rtlwifi/rtl8822be/fw.c
+++ b/drivers/staging/rtlwifi/rtl8822be/fw.c
@@ -741,6 +741,8 @@ void rtl8822be_set_fw_rsvdpagepkt(struct ieee80211_hw *hw, bool b_dl_finished)
 		      u1_rsvd_page_loc, 3);
 
 	skb = dev_alloc_skb(totalpacketlen);
+	if (!skb)
+		return;
 	memcpy((u8 *)skb_put(skb, totalpacketlen), &reserved_page_packet,
 	       totalpacketlen);
 
-- 
2.19.1

[PATCH AUTOSEL 5.0 43/98] staging: rtl8712: uninitialized memory in read_bbreg_hdl()

[Sasha Levin]

From: Dan Carpenter <dan.carpenter@oracle.com>

[ Upstream commit 22c971db7dd4b0ad8dd88e99c407f7a1f4231a2e ]

Colin King reported a bug in read_bbreg_hdl():

	memcpy(pcmd->rsp, (u8 *)&val, pcmd->rspsz);

The problem is that "val" is uninitialized.

This code is obviously not useful, but so far as I can tell
"pcmd->cmdcode" is never GEN_CMD_CODE(_Read_BBREG) so it's not harmful
either.  For now the easiest fix is to just call r8712_free_cmd_obj()
and return.

Fixes: 2865d42c78a9 ("staging: r8712u: Add the new driver to the mainline kernel")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/staging/rtl8712/rtl8712_cmd.c | 10 +---------
 drivers/staging/rtl8712/rtl8712_cmd.h |  2 +-
 2 files changed, 2 insertions(+), 10 deletions(-)

diff --git a/drivers/staging/rtl8712/rtl8712_cmd.c b/drivers/staging/rtl8712/rtl8712_cmd.c
index 1920d02f7c9f..8c36acedf507 100644
--- a/drivers/staging/rtl8712/rtl8712_cmd.c
+++ b/drivers/staging/rtl8712/rtl8712_cmd.c
@@ -147,17 +147,9 @@ static u8 write_macreg_hdl(struct _adapter *padapter, u8 *pbuf)
 
 static u8 read_bbreg_hdl(struct _adapter *padapter, u8 *pbuf)
 {
-	u32 val;
-	void (*pcmd_callback)(struct _adapter *dev, struct cmd_obj	*pcmd);
 	struct cmd_obj *pcmd  = (struct cmd_obj *)pbuf;
 
-	if (pcmd->rsp && pcmd->rspsz > 0)
-		memcpy(pcmd->rsp, (u8 *)&val, pcmd->rspsz);
-	pcmd_callback = cmd_callback[pcmd->cmdcode].callback;
-	if (!pcmd_callback)
-		r8712_free_cmd_obj(pcmd);
-	else
-		pcmd_callback(padapter, pcmd);
+	r8712_free_cmd_obj(pcmd);
 	return H2C_SUCCESS;
 }
 
diff --git a/drivers/staging/rtl8712/rtl8712_cmd.h b/drivers/staging/rtl8712/rtl8712_cmd.h
index 92fb77666d44..1ef86b8c592f 100644
--- a/drivers/staging/rtl8712/rtl8712_cmd.h
+++ b/drivers/staging/rtl8712/rtl8712_cmd.h
@@ -140,7 +140,7 @@ enum rtl8712_h2c_cmd {
 static struct _cmd_callback	cmd_callback[] = {
 	{GEN_CMD_CODE(_Read_MACREG), NULL}, /*0*/
 	{GEN_CMD_CODE(_Write_MACREG), NULL},
-	{GEN_CMD_CODE(_Read_BBREG), &r8712_getbbrfreg_cmdrsp_callback},
+	{GEN_CMD_CODE(_Read_BBREG), NULL},
 	{GEN_CMD_CODE(_Write_BBREG), NULL},
 	{GEN_CMD_CODE(_Read_RFREG), &r8712_getbbrfreg_cmdrsp_callback},
 	{GEN_CMD_CODE(_Write_RFREG), NULL}, /*5*/
-- 
2.19.1

[PATCH AUTOSEL 5.0 44/98] staging: rtlwifi: Fix potential NULL pointer dereference of kzalloc

[Sasha Levin]

From: Aditya Pakki <pakki001@umn.edu>

[ Upstream commit 6a8ca24590a2136921439b376c926c11a6effc0e ]

phydm.internal is allocated using kzalloc which is used multiple
times without a check for NULL pointer. This patch avoids such a
scenario by returning 0, consistent with the failure case.

Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/staging/rtlwifi/phydm/rtl_phydm.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/staging/rtlwifi/phydm/rtl_phydm.c b/drivers/staging/rtlwifi/phydm/rtl_phydm.c
index 9930ed954abb..4cc77b2016e1 100644
--- a/drivers/staging/rtlwifi/phydm/rtl_phydm.c
+++ b/drivers/staging/rtlwifi/phydm/rtl_phydm.c
@@ -180,6 +180,8 @@ static int rtl_phydm_init_priv(struct rtl_priv *rtlpriv,
 
 	rtlpriv->phydm.internal =
 		kzalloc(sizeof(struct phy_dm_struct), GFP_KERNEL);
+	if (!rtlpriv->phydm.internal)
+		return 0;
 
 	_rtl_phydm_init_com_info(rtlpriv, ic, params);
 
-- 
2.19.1

[PATCH AUTOSEL 5.0 45/98] net: phy: Add DP83825I to the DP83822 driver

[Sasha Levin]

From: Dan Murphy <dmurphy@ti.com>

[ Upstream commit 06acc17a96215a11134114aee26532b12dc8fde1 ]

Add the DP83825I ethernet PHY to the DP83822 driver.
These devices share the same WoL register bits and addresses.

The phy_driver init was made into a macro as there may be future
devices appended to this driver that will share the register space.

http://www.ti.com/lit/gpn/dp83825i

Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/net/phy/dp83822.c | 34 ++++++++++++++++++++--------------
 1 file changed, 20 insertions(+), 14 deletions(-)

diff --git a/drivers/net/phy/dp83822.c b/drivers/net/phy/dp83822.c
index 24c7f149f3e6..e11057892f07 100644
--- a/drivers/net/phy/dp83822.c
+++ b/drivers/net/phy/dp83822.c
@@ -23,6 +23,8 @@
 #include <linux/netdevice.h>
 
 #define DP83822_PHY_ID	        0x2000a240
+#define DP83825I_PHY_ID		0x2000a150
+
 #define DP83822_DEVADDR		0x1f
 
 #define MII_DP83822_PHYSCR	0x11
@@ -312,26 +314,30 @@ static int dp83822_resume(struct phy_device *phydev)
 	return 0;
 }
 
+#define DP83822_PHY_DRIVER(_id, _name)				\
+	{							\
+		PHY_ID_MATCH_MODEL(_id),			\
+		.name		= (_name),			\
+		.features	= PHY_BASIC_FEATURES,		\
+		.soft_reset	= dp83822_phy_reset,		\
+		.config_init	= dp83822_config_init,		\
+		.get_wol = dp83822_get_wol,			\
+		.set_wol = dp83822_set_wol,			\
+		.ack_interrupt = dp83822_ack_interrupt,		\
+		.config_intr = dp83822_config_intr,		\
+		.suspend = dp83822_suspend,			\
+		.resume = dp83822_resume,			\
+	}
+
 static struct phy_driver dp83822_driver[] = {
-	{
-		.phy_id = DP83822_PHY_ID,
-		.phy_id_mask = 0xfffffff0,
-		.name = "TI DP83822",
-		.features = PHY_BASIC_FEATURES,
-		.config_init = dp83822_config_init,
-		.soft_reset = dp83822_phy_reset,
-		.get_wol = dp83822_get_wol,
-		.set_wol = dp83822_set_wol,
-		.ack_interrupt = dp83822_ack_interrupt,
-		.config_intr = dp83822_config_intr,
-		.suspend = dp83822_suspend,
-		.resume = dp83822_resume,
-	 },
+	DP83822_PHY_DRIVER(DP83822_PHY_ID, "TI DP83822"),
+	DP83822_PHY_DRIVER(DP83825I_PHY_ID, "TI DP83825I"),
 };
 module_phy_driver(dp83822_driver);
 
 static struct mdio_device_id __maybe_unused dp83822_tbl[] = {
 	{ DP83822_PHY_ID, 0xfffffff0 },
+	{ DP83825I_PHY_ID, 0xfffffff0 },
 	{ },
 };
 MODULE_DEVICE_TABLE(mdio, dp83822_tbl);
-- 
2.19.1

[PATCH AUTOSEL 5.0 46/98] net: macb: Add null check for PCLK and HCLK

[Sasha Levin]

From: Harini Katakam <harini.katakam@xilinx.com>

[ Upstream commit cd5afa91f078c0787be0a62b5ef90301c00b0271 ]

Both PCLK and HCLK are "required" clocks according to macb devicetree
documentation. There is a chance that devm_clk_get doesn't return a
negative error but just a NULL clock structure instead. In such a case
the driver proceeds as usual and uses pclk value 0 to calculate MDC
divisor which is incorrect. Hence fix the same in clock initialization.

Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/net/ethernet/cadence/macb_main.c | 10 ++++++++--
 1 file changed, 8 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/cadence/macb_main.c b/drivers/net/ethernet/cadence/macb_main.c
index 2b2882615e8b..6cbe515bfdeb 100644
--- a/drivers/net/ethernet/cadence/macb_main.c
+++ b/drivers/net/ethernet/cadence/macb_main.c
@@ -3318,14 +3318,20 @@ static int macb_clk_init(struct platform_device *pdev, struct clk **pclk,
 		*hclk = devm_clk_get(&pdev->dev, "hclk");
 	}
 
-	if (IS_ERR(*pclk)) {
+	if (IS_ERR_OR_NULL(*pclk)) {
 		err = PTR_ERR(*pclk);
+		if (!err)
+			err = -ENODEV;
+
 		dev_err(&pdev->dev, "failed to get macb_clk (%u)\n", err);
 		return err;
 	}
 
-	if (IS_ERR(*hclk)) {
+	if (IS_ERR_OR_NULL(*hclk)) {
 		err = PTR_ERR(*hclk);
+		if (!err)
+			err = -ENODEV;
+
 		dev_err(&pdev->dev, "failed to get hclk (%u)\n", err);
 		return err;
 	}
-- 
2.19.1

[PATCH AUTOSEL 5.0 47/98] net/sched: don't dereference a->goto_chain to read the chain index

[Sasha Levin]

From: Davide Caratti <dcaratti@redhat.com>

[ Upstream commit fe384e2fa36ca084a456fd30558cccc75b4b3fbd ]

callers of tcf_gact_goto_chain_index() can potentially read an old value
of the chain index, or even dereference a NULL 'goto_chain' pointer,
because 'goto_chain' and 'tcfa_action' are read in the traffic path
without caring of concurrent write in the control path. The most recent
value of chain index can be read also from a->tcfa_action (it's encoded
there together with TC_ACT_GOTO_CHAIN bits), so we don't really need to
dereference 'goto_chain': just read the chain id from the control action.

Fixes: e457d86ada27 ("net: sched: add couple of goto_chain helpers")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 include/net/tc_act/tc_gact.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/include/net/tc_act/tc_gact.h b/include/net/tc_act/tc_gact.h
index ef8dd0db70ce..56935bf027a7 100644
--- a/include/net/tc_act/tc_gact.h
+++ b/include/net/tc_act/tc_gact.h
@@ -56,7 +56,7 @@ static inline bool is_tcf_gact_goto_chain(const struct tc_action *a)
 
 static inline u32 tcf_gact_goto_chain_index(const struct tc_action *a)
 {
-	return a->goto_chain->index;
+	return READ_ONCE(a->tcfa_action) & TC_ACT_EXT_VAL_MASK;
 }
 
 #endif /* __NET_TC_GACT_H */
-- 
2.19.1

[PATCH AUTOSEL 5.0 48/98] ARM: dts: imx6qdl: Fix typo in imx6qdl-icore-rqs.dtsi

[Sasha Levin]

From: Masanari Iida <standby24x7@gmail.com>

[ Upstream commit 41b37f4c0fa67185691bcbd30201cad566f2f0d1 ]

This patch fixes a spelling typo.

Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Fixes: cc42603de320 ("ARM: dts: imx6q-icore-rqs: Add Engicam IMX6 Q7 initial support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
index 1d1b4bd0670f..a4217f564a53 100644
--- a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
@@ -264,7 +264,7 @@
 	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
 	vmcc-supply = <&reg_sd3_vmmc>;
 	cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
-	bus-witdh = <4>;
+	bus-width = <4>;
 	no-1-8-v;
 	status = "okay";
 };
@@ -275,7 +275,7 @@
 	pinctrl-1 = <&pinctrl_usdhc4_100mhz>;
 	pinctrl-2 = <&pinctrl_usdhc4_200mhz>;
 	vmcc-supply = <&reg_sd4_vmmc>;
-	bus-witdh = <8>;
+	bus-width = <8>;
 	no-1-8-v;
 	non-removable;
 	status = "okay";
-- 
2.19.1

[PATCH AUTOSEL 5.0 49/98] drm/tegra: hub: Fix dereference before check

[Sasha Levin]

From: Thierry Reding <treding@nvidia.com>

[ Upstream commit 7cf77b273a8fc51e7de622fa6691abd4436a9a6b ]

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/gpu/drm/tegra/hub.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/tegra/hub.c b/drivers/gpu/drm/tegra/hub.c
index 922a48d5a483..c7c612579270 100644
--- a/drivers/gpu/drm/tegra/hub.c
+++ b/drivers/gpu/drm/tegra/hub.c
@@ -378,14 +378,16 @@ static int tegra_shared_plane_atomic_check(struct drm_plane *plane,
 static void tegra_shared_plane_atomic_disable(struct drm_plane *plane,
 					      struct drm_plane_state *old_state)
 {
-	struct tegra_dc *dc = to_tegra_dc(old_state->crtc);
 	struct tegra_plane *p = to_tegra_plane(plane);
+	struct tegra_dc *dc;
 	u32 value;
 
 	/* rien ne va plus */
 	if (!old_state || !old_state->crtc)
 		return;
 
+	dc = to_tegra_dc(old_state->crtc);
+
 	/*
 	 * XXX Legacy helpers seem to sometimes call ->atomic_disable() even
 	 * on planes that are already disabled. Make sure we fallback to the
-- 
2.19.1

[PATCH AUTOSEL 5.0 50/98] NFS: Fix a typo in nfs_init_timeout_values()

[Sasha Levin]

From: Trond Myklebust <trond.myklebust@hammerspace.com>

[ Upstream commit 5a698243930c441afccec04e4d5dc8febfd2b775 ]

Specifying a retrans=0 mount parameter to a NFS/TCP mount, is
inadvertently causing the NFS client to rewrite any specified
timeout parameter to the default of 60 seconds.

Fixes: a956beda19a6 ("NFS: Allow the mount option retrans=0")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 fs/nfs/client.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/fs/nfs/client.c b/fs/nfs/client.c
index fb1cf1a4bda2..90d71fda65ce 100644
--- a/fs/nfs/client.c
+++ b/fs/nfs/client.c
@@ -453,7 +453,7 @@ void nfs_init_timeout_values(struct rpc_timeout *to, int proto,
 	case XPRT_TRANSPORT_RDMA:
 		if (retrans == NFS_UNSPEC_RETRANS)
 			to->to_retries = NFS_DEF_TCP_RETRANS;
-		if (timeo == NFS_UNSPEC_TIMEO || to->to_retries == 0)
+		if (timeo == NFS_UNSPEC_TIMEO || to->to_initval == 0)
 			to->to_initval = NFS_DEF_TCP_TIMEO * HZ / 10;
 		if (to->to_initval > NFS_MAX_TCP_TIMEOUT)
 			to->to_initval = NFS_MAX_TCP_TIMEOUT;
-- 
2.19.1

[PATCH AUTOSEL 5.0 51/98] net: xilinx: fix possible object reference leak

[Sasha Levin]

From: Wen Yang <wen.yang99@zte.com.cn>

[ Upstream commit fa3a419d2f674b431d38748cb58fb7da17ee8949 ]

The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.

Detected by coccinelle with the following warnings:
./drivers/net/ethernet/xilinx/xilinx_axienet_main.c:1624:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1569, but without a corresponding object release within this function.

Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Anirudha Sarangi <anirudh@xilinx.com>
Cc: John Linn <John.Linn@xilinx.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/net/ethernet/xilinx/xilinx_axienet_main.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
index 0789d8af7d72..1ef56edb3918 100644
--- a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
+++ b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
@@ -1575,12 +1575,14 @@ static int axienet_probe(struct platform_device *pdev)
 	ret = of_address_to_resource(np, 0, &dmares);
 	if (ret) {
 		dev_err(&pdev->dev, "unable to get DMA resource\n");
+		of_node_put(np);
 		goto free_netdev;
 	}
 	lp->dma_regs = devm_ioremap_resource(&pdev->dev, &dmares);
 	if (IS_ERR(lp->dma_regs)) {
 		dev_err(&pdev->dev, "could not map DMA regs\n");
 		ret = PTR_ERR(lp->dma_regs);
+		of_node_put(np);
 		goto free_netdev;
 	}
 	lp->rx_irq = irq_of_parse_and_map(np, 1);
-- 
2.19.1

[PATCH AUTOSEL 5.0 52/98] net: ibm: fix possible object reference leak

[Sasha Levin]

From: Wen Yang <wen.yang99@zte.com.cn>

[ Upstream commit be693df3cf9dd113ff1d2c0d8150199efdba37f6 ]

The call to ehea_get_eth_dn returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.

Detected by coccinelle with the following warnings:
./drivers/net/ethernet/ibm/ehea/ehea_main.c:3163:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3154, but without a corresponding object release within this function.

Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Douglas Miller <dougmill@linux.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/net/ethernet/ibm/ehea/ehea_main.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/ethernet/ibm/ehea/ehea_main.c b/drivers/net/ethernet/ibm/ehea/ehea_main.c
index 3baabdc89726..90b62c1412c8 100644
--- a/drivers/net/ethernet/ibm/ehea/ehea_main.c
+++ b/drivers/net/ethernet/ibm/ehea/ehea_main.c
@@ -3160,6 +3160,7 @@ static ssize_t ehea_probe_port(struct device *dev,
 
 	if (ehea_add_adapter_mr(adapter)) {
 		pr_err("creating MR failed\n");
+		of_node_put(eth_dn);
 		return -EIO;
 	}
 
-- 
2.19.1

[PATCH AUTOSEL 5.0 53/98] net: ethernet: ti: fix possible object reference leak

[Sasha Levin]

From: Wen Yang <wen.yang99@zte.com.cn>

[ Upstream commit 75eac7b5f68b0a0671e795ac636457ee27cc11d8 ]

The call to of_get_child_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.

Detected by coccinelle with the following warnings:
./drivers/net/ethernet/ti/netcp_ethss.c:3661:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3654, but without a corresponding object release within this function.
./drivers/net/ethernet/ti/netcp_ethss.c:3665:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3654, but without a corresponding object release within this function.

Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/net/ethernet/ti/netcp_ethss.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/ti/netcp_ethss.c b/drivers/net/ethernet/ti/netcp_ethss.c
index 5174d318901e..0a920c5936b2 100644
--- a/drivers/net/ethernet/ti/netcp_ethss.c
+++ b/drivers/net/ethernet/ti/netcp_ethss.c
@@ -3657,12 +3657,16 @@ static int gbe_probe(struct netcp_device *netcp_device, struct device *dev,
 
 	ret = netcp_txpipe_init(&gbe_dev->tx_pipe, netcp_device,
 				gbe_dev->dma_chan_name, gbe_dev->tx_queue_id);
-	if (ret)
+	if (ret) {
+		of_node_put(interfaces);
 		return ret;
+	}
 
 	ret = netcp_txpipe_open(&gbe_dev->tx_pipe);
-	if (ret)
+	if (ret) {
+		of_node_put(interfaces);
 		return ret;
+	}
 
 	/* Create network interfaces */
 	INIT_LIST_HEAD(&gbe_dev->gbe_intf_head);
-- 
2.19.1

[PATCH AUTOSEL 5.0 54/98] drm: Fix drm_release() and device unplug

[Sasha Levin]

From: Noralf Trønnes <noralf@tronnes.org>

[ Upstream commit 3f04e0a6cfebf48152ac64502346cdc258811f79 ]

If userspace has open fd(s) when drm_dev_unplug() is run, it will result
in drm_dev_unregister() being called twice. First in drm_dev_unplug() and
then later in drm_release() through the call to drm_put_dev().

Since userspace already holds a ref on drm_device through the drm_minor,
it's not necessary to add extra ref counting based on no open file
handles. Instead just drm_dev_put() unconditionally in drm_dev_unplug().

We now have this:
- Userpace holds a ref on drm_device as long as there's open fd(s)
- The driver holds a ref on drm_device as long as it's bound to the
  struct device

When both sides are done with drm_device, it is released.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190208140103.28919-2-noralf@tronnes.org
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/gpu/drm/drm_drv.c  | 6 +-----
 drivers/gpu/drm/drm_file.c | 6 ++----
 2 files changed, 3 insertions(+), 9 deletions(-)

diff --git a/drivers/gpu/drm/drm_drv.c b/drivers/gpu/drm/drm_drv.c
index 12e5e2be7890..7a59b8b3ed5a 100644
--- a/drivers/gpu/drm/drm_drv.c
+++ b/drivers/gpu/drm/drm_drv.c
@@ -381,11 +381,7 @@ void drm_dev_unplug(struct drm_device *dev)
 	synchronize_srcu(&drm_unplug_srcu);
 
 	drm_dev_unregister(dev);
-
-	mutex_lock(&drm_global_mutex);
-	if (dev->open_count == 0)
-		drm_dev_put(dev);
-	mutex_unlock(&drm_global_mutex);
+	drm_dev_put(dev);
 }
 EXPORT_SYMBOL(drm_dev_unplug);
 
diff --git a/drivers/gpu/drm/drm_file.c b/drivers/gpu/drm/drm_file.c
index 46f48f245eb5..3f20f598cd7c 100644
--- a/drivers/gpu/drm/drm_file.c
+++ b/drivers/gpu/drm/drm_file.c
@@ -479,11 +479,9 @@ int drm_release(struct inode *inode, struct file *filp)
 
 	drm_file_free(file_priv);
 
-	if (!--dev->open_count) {
+	if (!--dev->open_count)
 		drm_lastclose(dev);
-		if (drm_dev_is_unplugged(dev))
-			drm_put_dev(dev);
-	}
+
 	mutex_unlock(&drm_global_mutex);
 
 	drm_minor_release(minor);
-- 
2.19.1

[PATCH AUTOSEL 5.0 55/98] gpio: aspeed: fix a potential NULL pointer dereference

[Sasha Levin]

From: Kangjie Lu <kjlu@umn.edu>

[ Upstream commit 6cf4511e9729c00a7306cf94085f9cc3c52ee723 ]

In case devm_kzalloc, the patch returns ENOMEM to avoid potential
NULL pointer dereference.

Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/gpio/gpio-aspeed.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/gpio/gpio-aspeed.c b/drivers/gpio/gpio-aspeed.c
index 854bce4fb9e7..217507002dbc 100644
--- a/drivers/gpio/gpio-aspeed.c
+++ b/drivers/gpio/gpio-aspeed.c
@@ -1224,6 +1224,8 @@ static int __init aspeed_gpio_probe(struct platform_device *pdev)
 
 	gpio->offset_timer =
 		devm_kzalloc(&pdev->dev, gpio->chip.ngpio, GFP_KERNEL);
+	if (!gpio->offset_timer)
+		return -ENOMEM;
 
 	return aspeed_gpio_setup_irqs(gpio, pdev);
 }
-- 
2.19.1

[PATCH AUTOSEL 5.0 56/98] drm/meson: Fix invalid pointer in meson_drv_unbind()

[Sasha Levin]

From: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>

[ Upstream commit 776e78677f514ecddd12dba48b9040958999bd5a ]

meson_drv_bind() registers a meson_drm struct as the device's privdata,
but meson_drv_unbind() tries to retrieve a drm_device. This may cause a
segfault on shutdown:

[ 5194.593429] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000197
 ...
[ 5194.788850] Call trace:
[ 5194.791349]  drm_dev_unregister+0x1c/0x118 [drm]
[ 5194.795848]  meson_drv_unbind+0x50/0x78 [meson_drm]

Retrieve the right pointer in meson_drv_unbind().

Fixes: bbbe775ec5b5 ("drm: Add support for Amlogic Meson Graphic Controller")
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322152657.13752-1-jean-philippe.brucker@arm.com
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/gpu/drm/meson/meson_drv.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/meson/meson_drv.c b/drivers/gpu/drm/meson/meson_drv.c
index 12ff47b13668..c1115a96453f 100644
--- a/drivers/gpu/drm/meson/meson_drv.c
+++ b/drivers/gpu/drm/meson/meson_drv.c
@@ -336,8 +336,8 @@ static int meson_drv_bind(struct device *dev)
 
 static void meson_drv_unbind(struct device *dev)
 {
-	struct drm_device *drm = dev_get_drvdata(dev);
-	struct meson_drm *priv = drm->dev_private;
+	struct meson_drm *priv = dev_get_drvdata(dev);
+	struct drm_device *drm = priv->drm;
 
 	if (priv->canvas) {
 		meson_canvas_free(priv->canvas, priv->canvas_id_osd1);
-- 
2.19.1

[PATCH AUTOSEL 5.0 57/98] drm/meson: Uninstall IRQ handler

[Sasha Levin]

From: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>

[ Upstream commit 2d8f92897ad816f5dda54b2ed2fd9f2d7cb1abde ]

meson_drv_unbind() doesn't unregister the IRQ handler, which can lead to
use-after-free if the IRQ fires after unbind:

[   64.656876] Unable to handle kernel paging request at virtual address ffff000011706dbc
...
[   64.662001] pc : meson_irq+0x18/0x30 [meson_drm]

I'm assuming that a similar problem could happen on the error path of
bind(), so uninstall the IRQ handler there as well.

Fixes: bbbe775ec5b5 ("drm: Add support for Amlogic Meson Graphic Controller")
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322152657.13752-2-jean-philippe.brucker@arm.com
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/gpu/drm/meson/meson_drv.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/meson/meson_drv.c b/drivers/gpu/drm/meson/meson_drv.c
index c1115a96453f..a13704ab5d11 100644
--- a/drivers/gpu/drm/meson/meson_drv.c
+++ b/drivers/gpu/drm/meson/meson_drv.c
@@ -317,12 +317,14 @@ static int meson_drv_bind_master(struct device *dev, bool has_components)
 
 	ret = drm_dev_register(drm, 0);
 	if (ret)
-		goto free_drm;
+		goto uninstall_irq;
 
 	drm_fbdev_generic_setup(drm, 32);
 
 	return 0;
 
+uninstall_irq:
+	drm_irq_uninstall(drm);
 free_drm:
 	drm_dev_put(drm);
 
@@ -347,6 +349,7 @@ static void meson_drv_unbind(struct device *dev)
 	}
 
 	drm_dev_unregister(drm);
+	drm_irq_uninstall(drm);
 	drm_kms_helper_poll_fini(drm);
 	drm_mode_config_cleanup(drm);
 	drm_dev_put(drm);
-- 
2.19.1

[PATCH AUTOSEL 5.0 58/98] ARM: davinci: fix build failure with allnoconfig

[Sasha Levin]

From: Sekhar Nori <nsekhar@ti.com>

[ Upstream commit 2dbed152e2d4c3fe2442284918d14797898b1e8a ]

allnoconfig build with just ARCH_DAVINCI enabled
fails because drivers/clk/davinci/* depends on
REGMAP being enabled.

Fix it by selecting REGMAP_MMIO when building in
DaVinci support.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 arch/arm/Kconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 26524b75970a..e5d56d9b712c 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -593,6 +593,7 @@ config ARCH_DAVINCI
 	select HAVE_IDE
 	select PM_GENERIC_DOMAINS if PM
 	select PM_GENERIC_DOMAINS_OF if PM && OF
+	select REGMAP_MMIO
 	select RESET_CONTROLLER
 	select USE_OF
 	select ZONE_DMA
-- 
2.19.1

[PATCH AUTOSEL 5.0 59/98] sbitmap: order READ/WRITE freed instance and setting clear bit

[Sasha Levin]

From: Ming Lei <ming.lei@redhat.com>

[ Upstream commit e6d1fa584e0dd9bfebaf345e9feea588cf75ead2 ]

Inside sbitmap_queue_clear(), once the clear bit is set, it will be
visiable to allocation path immediately. Meantime READ/WRITE on old
associated instance(such as request in case of blk-mq) may be
out-of-order with the setting clear bit, so race with re-allocation
may be triggered.

Adds one memory barrier for ordering READ/WRITE of the freed associated
instance with setting clear bit for avoiding race with re-allocation.

The following kernel oops triggerd by block/006 on aarch64 may be fixed:

[  142.330954] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000330
[  142.338794] Mem abort info:
[  142.341554]   ESR = 0x96000005
[  142.344632]   Exception class = DABT (current EL), IL = 32 bits
[  142.350500]   SET = 0, FnV = 0
[  142.353544]   EA = 0, S1PTW = 0
[  142.356678] Data abort info:
[  142.359528]   ISV = 0, ISS = 0x00000005
[  142.363343]   CM = 0, WnR = 0
[  142.366305] user pgtable: 64k pages, 48-bit VAs, pgdp = 000000002a3c51c0
[  142.372983] [0000000000000330] pgd=0000000000000000, pud=0000000000000000
[  142.379777] Internal error: Oops: 96000005 [#1] SMP
[  142.384613] Modules linked in: null_blk ib_isert iscsi_target_mod ib_srpt target_core_mod ib_srp scsi_transport_srp vfat fat rpcrdma sunrpc rdma_ucm ib_iser rdma_cm iw_cm libiscsi ib_umad scsi_transport_iscsi ib_ipoib ib_cm mlx5_ib ib_uverbs ib_core sbsa_gwdt crct10dif_ce ghash_ce ipmi_ssif sha2_ce ipmi_devintf sha256_arm64 sg sha1_ce ipmi_msghandler ip_tables xfs libcrc32c mlx5_core sdhci_acpi mlxfw ahci_platform at803x sdhci libahci_platform qcom_emac mmc_core hdma hdma_mgmt i2c_dev [last unloaded: null_blk]
[  142.429753] CPU: 7 PID: 1983 Comm: fio Not tainted 5.0.0.cki #2
[  142.449458] pstate: 00400005 (nzcv daif +PAN -UAO)
[  142.454239] pc : __blk_mq_free_request+0x4c/0xa8
[  142.458830] lr : blk_mq_free_request+0xec/0x118
[  142.463344] sp : ffff00003360f6a0
[  142.466646] x29: ffff00003360f6a0 x28: ffff000010e70000
[  142.471941] x27: ffff801729a50048 x26: 0000000000010000
[  142.477232] x25: ffff00003360f954 x24: ffff7bdfff021440
[  142.482529] x23: 0000000000000000 x22: 00000000ffffffff
[  142.487830] x21: ffff801729810000 x20: 0000000000000000
[  142.493123] x19: ffff801729a50000 x18: 0000000000000000
[  142.498413] x17: 0000000000000000 x16: 0000000000000001
[  142.503709] x15: 00000000000000ff x14: ffff7fe000000000
[  142.509003] x13: ffff8017dcde09a0 x12: 0000000000000000
[  142.514308] x11: 0000000000000001 x10: 0000000000000008
[  142.519597] x9 : ffff8017dcde09a0 x8 : 0000000000002000
[  142.524889] x7 : ffff8017dcde0a00 x6 : 000000015388f9be
[  142.530187] x5 : 0000000000000001 x4 : 0000000000000000
[  142.535478] x3 : 0000000000000000 x2 : 0000000000000000
[  142.540777] x1 : 0000000000000001 x0 : ffff00001041b194
[  142.546071] Process fio (pid: 1983, stack limit = 0x000000006460a0ea)
[  142.552500] Call trace:
[  142.554926]  __blk_mq_free_request+0x4c/0xa8
[  142.559181]  blk_mq_free_request+0xec/0x118
[  142.563352]  blk_mq_end_request+0xfc/0x120
[  142.567444]  end_cmd+0x3c/0xa8 [null_blk]
[  142.571434]  null_complete_rq+0x20/0x30 [null_blk]
[  142.576194]  blk_mq_complete_request+0x108/0x148
[  142.580797]  null_handle_cmd+0x1d4/0x718 [null_blk]
[  142.585662]  null_queue_rq+0x60/0xa8 [null_blk]
[  142.590171]  blk_mq_try_issue_directly+0x148/0x280
[  142.594949]  blk_mq_try_issue_list_directly+0x9c/0x108
[  142.600064]  blk_mq_sched_insert_requests+0xb0/0xd0
[  142.604926]  blk_mq_flush_plug_list+0x16c/0x2a0
[  142.609441]  blk_flush_plug_list+0xec/0x118
[  142.613608]  blk_finish_plug+0x3c/0x4c
[  142.617348]  blkdev_direct_IO+0x3b4/0x428
[  142.621336]  generic_file_read_iter+0x84/0x180
[  142.625761]  blkdev_read_iter+0x50/0x78
[  142.629579]  aio_read.isra.6+0xf8/0x190
[  142.633409]  __io_submit_one.isra.8+0x148/0x738
[  142.637912]  io_submit_one.isra.9+0x88/0xb8
[  142.642078]  __arm64_sys_io_submit+0xe0/0x238
[  142.646428]  el0_svc_handler+0xa0/0x128
[  142.650238]  el0_svc+0x8/0xc
[  142.653104] Code: b9402a63 f9000a7f 3100047f 540000a0 (f9419a81)
[  142.659202] ---[ end trace 467586bc175eb09d ]---

Fixes: ea86ea2cdced20057da ("sbitmap: ammortize cost of clearing bits")
Reported-and-bisected_and_tested-by: Yi Zhang <yi.zhang@redhat.com>
Cc: Yi Zhang <yi.zhang@redhat.com>
Cc: "jianchao.wang" <jianchao.w.wang@oracle.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 lib/sbitmap.c | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/lib/sbitmap.c b/lib/sbitmap.c
index 5b382c1244ed..155fe38756ec 100644
--- a/lib/sbitmap.c
+++ b/lib/sbitmap.c
@@ -591,6 +591,17 @@ EXPORT_SYMBOL_GPL(sbitmap_queue_wake_up);
 void sbitmap_queue_clear(struct sbitmap_queue *sbq, unsigned int nr,
 			 unsigned int cpu)
 {
+	/*
+	 * Once the clear bit is set, the bit may be allocated out.
+	 *
+	 * Orders READ/WRITE on the asssociated instance(such as request
+	 * of blk_mq) by this bit for avoiding race with re-allocation,
+	 * and its pair is the memory barrier implied in __sbitmap_get_word.
+	 *
+	 * One invariant is that the clear bit has to be zero when the bit
+	 * is in use.
+	 */
+	smp_mb__before_atomic();
 	sbitmap_deferred_clear_bit(&sbq->sb, nr);
 
 	/*
-- 
2.19.1

[PATCH AUTOSEL 5.0 60/98] staging: vc04_services: Fix an error code in vchiq_probe()

[Sasha Levin]

From: Dan Carpenter <dan.carpenter@oracle.com>

[ Upstream commit 9b9c87cf51783cbe7140c51472762094033cfeab ]

We need to set "err" on this error path.

Fixes: 187ac53e590c ("staging: vchiq_arm: rework probe and init functions")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 .../staging/vc04_services/interface/vchiq_arm/vchiq_arm.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c b/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c
index 804daf83be35..064d0db4c51e 100644
--- a/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c
+++ b/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c
@@ -3513,6 +3513,7 @@ static int vchiq_probe(struct platform_device *pdev)
 	struct device_node *fw_node;
 	const struct of_device_id *of_id;
 	struct vchiq_drvdata *drvdata;
+	struct device *vchiq_dev;
 	int err;
 
 	of_id = of_match_node(vchiq_of_match, pdev->dev.of_node);
@@ -3547,9 +3548,12 @@ static int vchiq_probe(struct platform_device *pdev)
 		goto failed_platform_init;
 	}
 
-	if (IS_ERR(device_create(vchiq_class, &pdev->dev, vchiq_devid,
-				 NULL, "vchiq")))
+	vchiq_dev = device_create(vchiq_class, &pdev->dev, vchiq_devid, NULL,
+				  "vchiq");
+	if (IS_ERR(vchiq_dev)) {
+		err = PTR_ERR(vchiq_dev);
 		goto failed_device_create;
+	}
 
 	vchiq_debugfs_init();
 
-- 
2.19.1

[PATCH AUTOSEL 5.0 61/98] libceph: fix breakage caused by multipage bvecs

[Sasha Levin]

From: Ilya Dryomov <idryomov@gmail.com>

[ Upstream commit 187df76325af5d9e12ae9daec1510307797e54f0 ]

A bvec can now consist of multiple physically contiguous pages.
This means that bvec_iter_advance() can move to a different page while
staying in the same bvec (i.e. ->bi_bvec_done != 0).

The messenger works in terms of segments which can now be defined as
the smaller of a bvec and a page.  The "more bytes to process in this
segment" condition holds only if bvec_iter_advance() leaves us in the
same bvec _and_ in the same page.  On next bvec (possibly in the same
page) and on next page (possibly in the same bvec) we may need to set
->last_piece.

Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 net/ceph/messenger.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/net/ceph/messenger.c b/net/ceph/messenger.c
index 7e71b0df1fbc..3083988ce729 100644
--- a/net/ceph/messenger.c
+++ b/net/ceph/messenger.c
@@ -840,6 +840,7 @@ static bool ceph_msg_data_bio_advance(struct ceph_msg_data_cursor *cursor,
 					size_t bytes)
 {
 	struct ceph_bio_iter *it = &cursor->bio_iter;
+	struct page *page = bio_iter_page(it->bio, it->iter);
 
 	BUG_ON(bytes > cursor->resid);
 	BUG_ON(bytes > bio_iter_len(it->bio, it->iter));
@@ -851,7 +852,8 @@ static bool ceph_msg_data_bio_advance(struct ceph_msg_data_cursor *cursor,
 		return false;   /* no more data */
 	}
 
-	if (!bytes || (it->iter.bi_size && it->iter.bi_bvec_done))
+	if (!bytes || (it->iter.bi_size && it->iter.bi_bvec_done &&
+		       page == bio_iter_page(it->bio, it->iter)))
 		return false;	/* more bytes to process in this segment */
 
 	if (!it->iter.bi_size) {
@@ -899,6 +901,7 @@ static bool ceph_msg_data_bvecs_advance(struct ceph_msg_data_cursor *cursor,
 					size_t bytes)
 {
 	struct bio_vec *bvecs = cursor->data->bvec_pos.bvecs;
+	struct page *page = bvec_iter_page(bvecs, cursor->bvec_iter);
 
 	BUG_ON(bytes > cursor->resid);
 	BUG_ON(bytes > bvec_iter_len(bvecs, cursor->bvec_iter));
@@ -910,7 +913,8 @@ static bool ceph_msg_data_bvecs_advance(struct ceph_msg_data_cursor *cursor,
 		return false;   /* no more data */
 	}
 
-	if (!bytes || cursor->bvec_iter.bi_bvec_done)
+	if (!bytes || (cursor->bvec_iter.bi_bvec_done &&
+		       page == bvec_iter_page(bvecs, cursor->bvec_iter)))
 		return false;	/* more bytes to process in this segment */
 
 	BUG_ON(cursor->last_piece);
-- 
2.19.1

[PATCH AUTOSEL 5.0 62/98] scsi: mpt3sas: Fix kernel panic during expander reset

[Sasha Levin]

From: Sreekanth Reddy <sreekanth.reddy@broadcom.com>

[ Upstream commit c2fe742ff6e77c5b4fe4ad273191ddf28fdea25e ]

During expander reset handling, the driver invokes kernel function
scsi_host_find_tag() to obtain outstanding requests associated with the
scsi host managed by the driver. Driver loops from tag value zero to hba
queue depth to obtain the outstanding scmds. But when blk-mq is enabled,
the block layer may return stale entry for one or more requests. This may
lead to kernel panic if the returned value is inaccessible or the memory
pointed by the returned value is reused.

Reference of upstream discussion:

	https://patchwork.kernel.org/patch/10734933/

Instead of calling scsi_host_find_tag() API for each and every smid (smid
is tag +1) from one to shost->can_queue, now driver will call this API (to
obtain the outstanding scmd) only for those smid's which are outstanding at
the driver level.

Driver will determine whether this smid is outstanding at driver level by
looking into it's corresponding MPI request frame, if its MPI request frame
is empty, then it means that this smid is free and does not need to call
scsi_host_find_tag() for it.  By doing this, driver will invoke
scsi_host_find_tag() for only those tags which are outstanding at the
driver level.

Driver will check whether particular MPI request frame is empty or not by
looking into the "DevHandle" field. If this field is zero then it means
that this MPI request is empty. For active MPI request DevHandle must be
non-zero.

Also driver will memset the MPI request frame once the corresponding scmd
is processed (i.e. just before calling
scmd->done function).

Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/scsi/mpt3sas/mpt3sas_base.c  |  6 ++++++
 drivers/scsi/mpt3sas/mpt3sas_scsih.c | 12 ++++++++++++
 2 files changed, 18 insertions(+)

diff --git a/drivers/scsi/mpt3sas/mpt3sas_base.c b/drivers/scsi/mpt3sas/mpt3sas_base.c
index 0a6cb8f0680c..c39f88100f31 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_base.c
+++ b/drivers/scsi/mpt3sas/mpt3sas_base.c
@@ -3281,12 +3281,18 @@ mpt3sas_base_free_smid(struct MPT3SAS_ADAPTER *ioc, u16 smid)
 
 	if (smid < ioc->hi_priority_smid) {
 		struct scsiio_tracker *st;
+		void *request;
 
 		st = _get_st_from_smid(ioc, smid);
 		if (!st) {
 			_base_recovery_check(ioc);
 			return;
 		}
+
+		/* Clear MPI request frame */
+		request = mpt3sas_base_get_msg_frame(ioc, smid);
+		memset(request, 0, ioc->request_sz);
+
 		mpt3sas_base_clear_st(ioc, st);
 		_base_recovery_check(ioc);
 		return;
diff --git a/drivers/scsi/mpt3sas/mpt3sas_scsih.c b/drivers/scsi/mpt3sas/mpt3sas_scsih.c
index 6be39dc27103..6173c211a5e5 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_scsih.c
+++ b/drivers/scsi/mpt3sas/mpt3sas_scsih.c
@@ -1462,11 +1462,23 @@ mpt3sas_scsih_scsi_lookup_get(struct MPT3SAS_ADAPTER *ioc, u16 smid)
 {
 	struct scsi_cmnd *scmd = NULL;
 	struct scsiio_tracker *st;
+	Mpi25SCSIIORequest_t *mpi_request;
 
 	if (smid > 0  &&
 	    smid <= ioc->scsiio_depth - INTERNAL_SCSIIO_CMDS_COUNT) {
 		u32 unique_tag = smid - 1;
 
+		mpi_request = mpt3sas_base_get_msg_frame(ioc, smid);
+
+		/*
+		 * If SCSI IO request is outstanding at driver level then
+		 * DevHandle filed must be non-zero. If DevHandle is zero
+		 * then it means that this smid is free at driver level,
+		 * so return NULL.
+		 */
+		if (!mpi_request->DevHandle)
+			return scmd;
+
 		scmd = scsi_host_find_tag(ioc->shost, unique_tag);
 		if (scmd) {
 			st = scsi_cmd_priv(scmd);
-- 
2.19.1

[PATCH AUTOSEL 5.0 63/98] scsi: aacraid: Insure we don't access PCIe space during AER/EEH

[Sasha Levin]

From: Dave Carroll <david.carroll@microsemi.com>

[ Upstream commit b6554cfe09e1f610aed7d57164ab7760be57acd9 ]

There are a few windows during AER/EEH when we can access PCIe I/O mapped
registers. This will harden the access to insure we do not allow PCIe
access during errors

Signed-off-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Sagar Biradar <sagar.biradar@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/scsi/aacraid/aacraid.h | 7 ++++++-
 drivers/scsi/aacraid/commsup.c | 4 ++--
 2 files changed, 8 insertions(+), 3 deletions(-)

diff --git a/drivers/scsi/aacraid/aacraid.h b/drivers/scsi/aacraid/aacraid.h
index 3291d1c16864..8bd09b96ea18 100644
--- a/drivers/scsi/aacraid/aacraid.h
+++ b/drivers/scsi/aacraid/aacraid.h
@@ -2640,9 +2640,14 @@ static inline unsigned int cap_to_cyls(sector_t capacity, unsigned divisor)
 	return capacity;
 }
 
+static inline int aac_pci_offline(struct aac_dev *dev)
+{
+	return pci_channel_offline(dev->pdev) || dev->handle_pci_error;
+}
+
 static inline int aac_adapter_check_health(struct aac_dev *dev)
 {
-	if (unlikely(pci_channel_offline(dev->pdev)))
+	if (unlikely(aac_pci_offline(dev)))
 		return -1;
 
 	return (dev)->a_ops.adapter_check_health(dev);
diff --git a/drivers/scsi/aacraid/commsup.c b/drivers/scsi/aacraid/commsup.c
index a3adc954f40f..09367b8a3885 100644
--- a/drivers/scsi/aacraid/commsup.c
+++ b/drivers/scsi/aacraid/commsup.c
@@ -672,7 +672,7 @@ int aac_fib_send(u16 command, struct fib *fibptr, unsigned long size,
 					return -ETIMEDOUT;
 				}
 
-				if (unlikely(pci_channel_offline(dev->pdev)))
+				if (unlikely(aac_pci_offline(dev)))
 					return -EFAULT;
 
 				if ((blink = aac_adapter_check_health(dev)) > 0) {
@@ -772,7 +772,7 @@ int aac_hba_send(u8 command, struct fib *fibptr, fib_callback callback,
 
 		spin_unlock_irqrestore(&fibptr->event_lock, flags);
 
-		if (unlikely(pci_channel_offline(dev->pdev)))
+		if (unlikely(aac_pci_offline(dev)))
 			return -EFAULT;
 
 		fibptr->flags |= FIB_CONTEXT_FLAG_WAIT;
-- 
2.19.1

[PATCH AUTOSEL 5.0 64/98] scsi: qla4xxx: fix a potential NULL pointer dereference

[Sasha Levin]

From: Kangjie Lu <kjlu@umn.edu>

[ Upstream commit fba1bdd2a9a93f3e2181ec1936a3c2f6b37e7ed6 ]

In case iscsi_lookup_endpoint fails, the fix returns -EINVAL to avoid NULL
pointer dereference.

Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/scsi/qla4xxx/ql4_os.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/scsi/qla4xxx/ql4_os.c b/drivers/scsi/qla4xxx/ql4_os.c
index a77bfb224248..80289c885c07 100644
--- a/drivers/scsi/qla4xxx/ql4_os.c
+++ b/drivers/scsi/qla4xxx/ql4_os.c
@@ -3203,6 +3203,8 @@ static int qla4xxx_conn_bind(struct iscsi_cls_session *cls_session,
 	if (iscsi_conn_bind(cls_session, cls_conn, is_leading))
 		return -EINVAL;
 	ep = iscsi_lookup_endpoint(transport_fd);
+	if (!ep)
+		return -EINVAL;
 	conn = cls_conn->dd_data;
 	qla_conn = conn->dd_data;
 	qla_conn->qla_ep = ep->dd_data;
-- 
2.19.1

[PATCH AUTOSEL 5.0 65/98] usb: usb251xb: fix to avoid potential NULL pointer dereference

[Sasha Levin]

From: Aditya Pakki <pakki001@umn.edu>

[ Upstream commit 41f00e6e9e55546390031996b773e7f3c1d95928 ]

of_match_device in usb251xb_probe can fail and returns a NULL pointer.
The patch avoids a potential NULL pointer dereference in this scenario.

Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Reviewed-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/usb/misc/usb251xb.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/usb/misc/usb251xb.c b/drivers/usb/misc/usb251xb.c
index a6efb9a72939..5f7734c729b1 100644
--- a/drivers/usb/misc/usb251xb.c
+++ b/drivers/usb/misc/usb251xb.c
@@ -601,7 +601,7 @@ static int usb251xb_probe(struct usb251xb *hub)
 							   dev);
 	int err;
 
-	if (np) {
+	if (np && of_id) {
 		err = usb251xb_get_ofdata(hub,
 					  (struct usb251xb_data *)of_id->data);
 		if (err) {
-- 
2.19.1

[PATCH AUTOSEL 5.0 66/98] leds: trigger: netdev: fix refcnt leak on interface rename

[Sasha Levin]

From: Rafał Miłecki <rafal@milecki.pl>

[ Upstream commit 4cb6560514fa19d556954b88128f3846fee66a03 ]

Renaming a netdev-trigger-tracked interface was resulting in an
unbalanced dev_hold().

Example:
> iw phy phy0 interface add foo type __ap
> echo netdev > trigger
> echo foo > device_name
> ip link set foo name bar
> iw dev bar del
[  237.355366] unregister_netdevice: waiting for bar to become free. Usage count = 1
[  247.435362] unregister_netdevice: waiting for bar to become free. Usage count = 1
[  257.545366] unregister_netdevice: waiting for bar to become free. Usage count = 1

Above problem was caused by trigger checking a dev->name which obviously
changes after renaming an interface. It meant missing all further events
including the NETDEV_UNREGISTER which is required for calling dev_put().

This change fixes that by:
1) Comparing device struct *address* for notification-filtering purposes
2) Dropping unneeded NETDEV_CHANGENAME code (no behavior change)

Fixes: 06f502f57d0d ("leds: trigger: Introduce a NETDEV trigger")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/leds/trigger/ledtrig-netdev.c | 13 +++++--------
 1 file changed, 5 insertions(+), 8 deletions(-)

diff --git a/drivers/leds/trigger/ledtrig-netdev.c b/drivers/leds/trigger/ledtrig-netdev.c
index 3dd3ed46d473..167a94c02d05 100644
--- a/drivers/leds/trigger/ledtrig-netdev.c
+++ b/drivers/leds/trigger/ledtrig-netdev.c
@@ -301,11 +301,11 @@ static int netdev_trig_notify(struct notifier_block *nb,
 		container_of(nb, struct led_netdev_data, notifier);
 
 	if (evt != NETDEV_UP && evt != NETDEV_DOWN && evt != NETDEV_CHANGE
-	    && evt != NETDEV_REGISTER && evt != NETDEV_UNREGISTER
-	    && evt != NETDEV_CHANGENAME)
+	    && evt != NETDEV_REGISTER && evt != NETDEV_UNREGISTER)
 		return NOTIFY_DONE;
 
-	if (strcmp(dev->name, trigger_data->device_name))
+	if (!(dev == trigger_data->net_dev ||
+	      (evt == NETDEV_REGISTER && !strcmp(dev->name, trigger_data->device_name))))
 		return NOTIFY_DONE;
 
 	cancel_delayed_work_sync(&trigger_data->work);
@@ -320,12 +320,9 @@ static int netdev_trig_notify(struct notifier_block *nb,
 		dev_hold(dev);
 		trigger_data->net_dev = dev;
 		break;
-	case NETDEV_CHANGENAME:
 	case NETDEV_UNREGISTER:
-		if (trigger_data->net_dev) {
-			dev_put(trigger_data->net_dev);
-			trigger_data->net_dev = NULL;
-		}
+		dev_put(trigger_data->net_dev);
+		trigger_data->net_dev = NULL;
 		break;
 	case NETDEV_UP:
 	case NETDEV_CHANGE:
-- 
2.19.1

[PATCH AUTOSEL 5.0 67/98] SUNRPC: fix uninitialized variable warning

[Sasha Levin]

From: Alakesh Haloi <alakesh.haloi@gmail.com>

[ Upstream commit 01f2f5b82a2b523ae76af53f2ff43c48dde10a00 ]

Avoid following compiler warning on uninitialized variable

net/sunrpc/xprtsock.c: In function ‘xs_read_stream_request.constprop’:
net/sunrpc/xprtsock.c:525:10: warning: ‘read’ may be used uninitialized in this function [-Wmaybe-uninitialized]
   return read;
          ^~~~
net/sunrpc/xprtsock.c:529:23: warning: ‘ret’ may be used uninitialized in this function [-Wmaybe-uninitialized]
  return ret < 0 ? ret : read;
         ~~~~~~~~~~~~~~^~~~~~

Signed-off-by: Alakesh Haloi <alakesh.haloi@gmail.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 net/sunrpc/xprtsock.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/net/sunrpc/xprtsock.c b/net/sunrpc/xprtsock.c
index 7754aa3e434f..f88c2bd1335a 100644
--- a/net/sunrpc/xprtsock.c
+++ b/net/sunrpc/xprtsock.c
@@ -486,8 +486,8 @@ xs_read_stream_request(struct sock_xprt *transport, struct msghdr *msg,
 		int flags, struct rpc_rqst *req)
 {
 	struct xdr_buf *buf = &req->rq_private_buf;
-	size_t want, read;
-	ssize_t ret;
+	size_t want, uninitialized_var(read);
+	ssize_t uninitialized_var(ret);
 
 	xs_read_header(transport, buf);
 
-- 
2.19.1

[PATCH AUTOSEL 5.0 68/98] x86/realmode: Don't leak the trampoline kernel address

[Sasha Levin]

From: Matteo Croce <mcroce@redhat.com>

[ Upstream commit b929a500d68479163c48739d809cbf4c1335db6f ]

Since commit

  ad67b74d2469 ("printk: hash addresses printed with %p")

at boot "____ptrval____" is printed instead of the trampoline addresses:

  Base memory trampoline at [(____ptrval____)] 99000 size 24576

Remove the print as we don't want to leak kernel addresses and this
statement is not needed anymore.

Fixes: ad67b74d2469d9b8 ("printk: hash addresses printed with %p")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190326203046.20787-1-mcroce@redhat.com
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 arch/x86/realmode/init.c | 2 --
 1 file changed, 2 deletions(-)

diff --git a/arch/x86/realmode/init.c b/arch/x86/realmode/init.c
index d10105825d57..47d097946872 100644
--- a/arch/x86/realmode/init.c
+++ b/arch/x86/realmode/init.c
@@ -20,8 +20,6 @@ void __init set_real_mode_mem(phys_addr_t mem, size_t size)
 	void *base = __va(mem);
 
 	real_mode_header = (struct real_mode_header *) base;
-	printk(KERN_DEBUG "Base memory trampoline at [%p] %llx size %zu\n",
-	       base, (unsigned long long)mem, size);
 }
 
 void __init reserve_real_mode(void)
-- 
2.19.1

[PATCH AUTOSEL 5.0 69/98] usb: u132-hcd: fix resource leak

[Sasha Levin]

From: Mukesh Ojha <mojha@codeaurora.org>

[ Upstream commit f276e002793cdb820862e8ea8f76769d56bba575 ]

if platform_driver_register fails, cleanup the allocated resource
gracefully.

Signed-off-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/usb/host/u132-hcd.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/usb/host/u132-hcd.c b/drivers/usb/host/u132-hcd.c
index 5b8a3d9530c4..5cac83aaeac3 100644
--- a/drivers/usb/host/u132-hcd.c
+++ b/drivers/usb/host/u132-hcd.c
@@ -3202,6 +3202,9 @@ static int __init u132_hcd_init(void)
 	printk(KERN_INFO "driver %s\n", hcd_name);
 	workqueue = create_singlethread_workqueue("u132");
 	retval = platform_driver_register(&u132_platform_driver);
+	if (retval)
+		destroy_workqueue(workqueue);
+
 	return retval;
 }
 
-- 
2.19.1

[PATCH AUTOSEL 5.0 70/98] tty: fix NULL pointer issue when tty_port ops is not set

[Sasha Levin]

From: Fabien Dessenne <fabien.dessenne@st.com>

[ Upstream commit f4e68d58cf2b20a581759bbc7228052534652673 ]

Unlike 'client_ops' which is initialized to 'default_client_ops', the
port operations 'ops' may be left to NULL.
Check the 'ops' value before checking the 'ops->x' value.

Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/tty/tty_port.c | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/drivers/tty/tty_port.c b/drivers/tty/tty_port.c
index 044c3cbdcfa4..a9e12b3bc31d 100644
--- a/drivers/tty/tty_port.c
+++ b/drivers/tty/tty_port.c
@@ -325,7 +325,7 @@ static void tty_port_shutdown(struct tty_port *port, struct tty_struct *tty)
 		if (tty && C_HUPCL(tty))
 			tty_port_lower_dtr_rts(port);
 
-		if (port->ops->shutdown)
+		if (port->ops && port->ops->shutdown)
 			port->ops->shutdown(port);
 	}
 out:
@@ -398,7 +398,7 @@ EXPORT_SYMBOL_GPL(tty_port_tty_wakeup);
  */
 int tty_port_carrier_raised(struct tty_port *port)
 {
-	if (port->ops->carrier_raised == NULL)
+	if (!port->ops || !port->ops->carrier_raised)
 		return 1;
 	return port->ops->carrier_raised(port);
 }
@@ -414,7 +414,7 @@ EXPORT_SYMBOL(tty_port_carrier_raised);
  */
 void tty_port_raise_dtr_rts(struct tty_port *port)
 {
-	if (port->ops->dtr_rts)
+	if (port->ops && port->ops->dtr_rts)
 		port->ops->dtr_rts(port, 1);
 }
 EXPORT_SYMBOL(tty_port_raise_dtr_rts);
@@ -429,7 +429,7 @@ EXPORT_SYMBOL(tty_port_raise_dtr_rts);
  */
 void tty_port_lower_dtr_rts(struct tty_port *port)
 {
-	if (port->ops->dtr_rts)
+	if (port->ops && port->ops->dtr_rts)
 		port->ops->dtr_rts(port, 0);
 }
 EXPORT_SYMBOL(tty_port_lower_dtr_rts);
@@ -684,7 +684,7 @@ int tty_port_open(struct tty_port *port, struct tty_struct *tty,
 
 	if (!tty_port_initialized(port)) {
 		clear_bit(TTY_IO_ERROR, &tty->flags);
-		if (port->ops->activate) {
+		if (port->ops && port->ops->activate) {
 			int retval = port->ops->activate(port, tty);
 			if (retval) {
 				mutex_unlock(&port->mutex);
-- 
2.19.1

[PATCH AUTOSEL 5.0 71/98] ceph: fix use-after-free on symlink traversal

[Sasha Levin]

From: Al Viro <viro@zeniv.linux.org.uk>

[ Upstream commit daf5cc27eed99afdea8d96e71b89ba41f5406ef6 ]

free the symlink body after the same RCU delay we have for freeing the
struct inode itself, so that traversal during RCU pathwalk wouldn't step
into freed memory.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 fs/ceph/inode.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/fs/ceph/inode.c b/fs/ceph/inode.c
index 9d1f34d46627..f7f9e305aaf8 100644
--- a/fs/ceph/inode.c
+++ b/fs/ceph/inode.c
@@ -524,6 +524,7 @@ static void ceph_i_callback(struct rcu_head *head)
 	struct inode *inode = container_of(head, struct inode, i_rcu);
 	struct ceph_inode_info *ci = ceph_inode(inode);
 
+	kfree(ci->i_symlink);
 	kmem_cache_free(ceph_inode_cachep, ci);
 }
 
@@ -561,7 +562,6 @@ void ceph_destroy_inode(struct inode *inode)
 		ceph_put_snap_realm(mdsc, realm);
 	}
 
-	kfree(ci->i_symlink);
 	while ((n = rb_first(&ci->i_fragtree)) != NULL) {
 		frag = rb_entry(n, struct ceph_inode_frag, node);
 		rb_erase(n, &ci->i_fragtree);
-- 
2.19.1

[PATCH AUTOSEL 5.0 72/98] scsi: zfcp: reduce flood of fcrscn1 trace records on multi-element RSCN

[Sasha Levin]

From: Steffen Maier <maier@linux.ibm.com>

[ Upstream commit c8206579175c34a2546de8a74262456278a7795a ]

If an incoming ELS of type RSCN contains more than one element, zfcp
suboptimally causes repeated erp trigger NOP trace records for each
previously failed port. These could be ports that went away.  It loops over
each RSCN element, and for each of those in an inner loop over all
zfcp_ports.

The trigger to recover failed ports should be just the reception of some
RSCN, no matter how many elements it has. So we can loop over failed ports
separately, and only then loop over each RSCN element to handle the
non-failed ports.

The call chain was:

  zfcp_fc_incoming_rscn
    for (i = 1; i < no_entries; i++)
      _zfcp_fc_incoming_rscn
        list_for_each_entry(port, &adapter->port_list, list)
          if (masked port->d_id match) zfcp_fc_test_link
          if (!port->d_id) zfcp_erp_port_reopen "fcrscn1"   <===

In order the reduce the "flooding" of the REC trace area in such cases, we
factor out handling the failed ports to be outside of the entries loop:

  zfcp_fc_incoming_rscn
    if (no_entries > 1)                                     <===
      list_for_each_entry(port, &adapter->port_list, list)  <===
        if (!port->d_id) zfcp_erp_port_reopen "fcrscn1"     <===
    for (i = 1; i < no_entries; i++)
      _zfcp_fc_incoming_rscn
        list_for_each_entry(port, &adapter->port_list, list)
          if (masked port->d_id match) zfcp_fc_test_link

Abbreviated example trace records before this code change:

Tag            : fcrscn1
WWPN           : 0x500507630310d327
ERP want       : 0x02
ERP need       : 0x02

Tag            : fcrscn1
WWPN           : 0x500507630310d327
ERP want       : 0x02
ERP need       : 0x00                 NOP => superfluous trace record

The last trace entry repeats if there are more than 2 RSCN elements.

Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/s390/scsi/zfcp_fc.c | 21 +++++++++++++++++----
 1 file changed, 17 insertions(+), 4 deletions(-)

diff --git a/drivers/s390/scsi/zfcp_fc.c b/drivers/s390/scsi/zfcp_fc.c
index db00b5e3abbe..33eddb02ee30 100644
--- a/drivers/s390/scsi/zfcp_fc.c
+++ b/drivers/s390/scsi/zfcp_fc.c
@@ -239,10 +239,6 @@ static void _zfcp_fc_incoming_rscn(struct zfcp_fsf_req *fsf_req, u32 range,
 	list_for_each_entry(port, &adapter->port_list, list) {
 		if ((port->d_id & range) == (ntoh24(page->rscn_fid) & range))
 			zfcp_fc_test_link(port);
-		if (!port->d_id)
-			zfcp_erp_port_reopen(port,
-					     ZFCP_STATUS_COMMON_ERP_FAILED,
-					     "fcrscn1");
 	}
 	read_unlock_irqrestore(&adapter->port_list_lock, flags);
 }
@@ -250,6 +246,7 @@ static void _zfcp_fc_incoming_rscn(struct zfcp_fsf_req *fsf_req, u32 range,
 static void zfcp_fc_incoming_rscn(struct zfcp_fsf_req *fsf_req)
 {
 	struct fsf_status_read_buffer *status_buffer = (void *)fsf_req->data;
+	struct zfcp_adapter *adapter = fsf_req->adapter;
 	struct fc_els_rscn *head;
 	struct fc_els_rscn_page *page;
 	u16 i;
@@ -263,6 +260,22 @@ static void zfcp_fc_incoming_rscn(struct zfcp_fsf_req *fsf_req)
 	no_entries = be16_to_cpu(head->rscn_plen) /
 		sizeof(struct fc_els_rscn_page);
 
+	if (no_entries > 1) {
+		/* handle failed ports */
+		unsigned long flags;
+		struct zfcp_port *port;
+
+		read_lock_irqsave(&adapter->port_list_lock, flags);
+		list_for_each_entry(port, &adapter->port_list, list) {
+			if (port->d_id)
+				continue;
+			zfcp_erp_port_reopen(port,
+					     ZFCP_STATUS_COMMON_ERP_FAILED,
+					     "fcrscn1");
+		}
+		read_unlock_irqrestore(&adapter->port_list_lock, flags);
+	}
+
 	for (i = 1; i < no_entries; i++) {
 		/* skip head and start with 1st element */
 		page++;
-- 
2.19.1

[PATCH AUTOSEL 5.0 73/98] x86/mm: Don't exceed the valid physical address space

[Sasha Levin]

From: Ralph Campbell <rcampbell@nvidia.com>

[ Upstream commit 92c77f7c4d5dfaaf45b2ce19360e69977c264766 ]

valid_phys_addr_range() is used to sanity check the physical address range
of an operation, e.g., access to /dev/mem. It uses __pa(high_memory)
internally.

If memory is populated at the end of the physical address space, then
__pa(high_memory) is outside of the physical address space because:

   high_memory = (void *)__va(max_pfn * PAGE_SIZE - 1) + 1;

For the comparison in valid_phys_addr_range() this is not an issue, but if
CONFIG_DEBUG_VIRTUAL is enabled, __pa() maps to __phys_addr(), which
verifies that the resulting physical address is within the valid physical
address space of the CPU. So in the case that memory is populated at the
end of the physical address space, this is not true and triggers a
VIRTUAL_BUG_ON().

Use __pa(high_memory - 1) to prevent the conversion from going beyond
the end of valid physical addresses.

Fixes: be62a3204406 ("x86/mm: Limit mmap() of /dev/mem to valid physical addresses")
Signed-off-by: Ralph Campbell <rcampbell@nvidia.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Craig Bergstrom <craigb@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Cc: Sean Young <sean@mess.org>

Link: https://lkml.kernel.org/r/20190326001817.15413-2-rcampbell@nvidia.com
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 arch/x86/mm/mmap.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/x86/mm/mmap.c b/arch/x86/mm/mmap.c
index db3165714521..dc726e07d8ba 100644
--- a/arch/x86/mm/mmap.c
+++ b/arch/x86/mm/mmap.c
@@ -230,7 +230,7 @@ bool mmap_address_hint_valid(unsigned long addr, unsigned long len)
 /* Can we access it for direct reading/writing? Must be RAM: */
 int valid_phys_addr_range(phys_addr_t addr, size_t count)
 {
-	return addr + count <= __pa(high_memory);
+	return addr + count - 1 <= __pa(high_memory - 1);
 }
 
 /* Can we access it through mmap? Must be a valid physical address: */
-- 
2.19.1

[PATCH AUTOSEL 5.0 74/98] libata: fix using DMA buffers on stack

[Sasha Levin]

From: raymond pang <raymondpangxd@gmail.com>

[ Upstream commit dd08a8d9a66de4b54575c294a92630299f7e0fe7 ]

When CONFIG_VMAP_STACK=y, __pa() returns incorrect physical address for
a stack virtual address. Stack DMA buffers must be avoided.

Signed-off-by: raymond pang <raymondpangxd@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/ata/libata-zpodd.c | 34 ++++++++++++++++++++++++----------
 1 file changed, 24 insertions(+), 10 deletions(-)

diff --git a/drivers/ata/libata-zpodd.c b/drivers/ata/libata-zpodd.c
index b3ed8f9953a8..173e6f2dd9af 100644
--- a/drivers/ata/libata-zpodd.c
+++ b/drivers/ata/libata-zpodd.c
@@ -52,38 +52,52 @@ static int eject_tray(struct ata_device *dev)
 /* Per the spec, only slot type and drawer type ODD can be supported */
 static enum odd_mech_type zpodd_get_mech_type(struct ata_device *dev)
 {
-	char buf[16];
+	char *buf;
 	unsigned int ret;
-	struct rm_feature_desc *desc = (void *)(buf + 8);
+	struct rm_feature_desc *desc;
 	struct ata_taskfile tf;
 	static const char cdb[] = {  GPCMD_GET_CONFIGURATION,
 			2,      /* only 1 feature descriptor requested */
 			0, 3,   /* 3, removable medium feature */
 			0, 0, 0,/* reserved */
-			0, sizeof(buf),
+			0, 16,
 			0, 0, 0,
 	};
 
+	buf = kzalloc(16, GFP_KERNEL);
+	if (!buf)
+		return ODD_MECH_TYPE_UNSUPPORTED;
+	desc = (void *)(buf + 8);
+
 	ata_tf_init(dev, &tf);
 	tf.flags = ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE;
 	tf.command = ATA_CMD_PACKET;
 	tf.protocol = ATAPI_PROT_PIO;
-	tf.lbam = sizeof(buf);
+	tf.lbam = 16;
 
 	ret = ata_exec_internal(dev, &tf, cdb, DMA_FROM_DEVICE,
-				buf, sizeof(buf), 0);
-	if (ret)
+				buf, 16, 0);
+	if (ret) {
+		kfree(buf);
 		return ODD_MECH_TYPE_UNSUPPORTED;
+	}
 
-	if (be16_to_cpu(desc->feature_code) != 3)
+	if (be16_to_cpu(desc->feature_code) != 3) {
+		kfree(buf);
 		return ODD_MECH_TYPE_UNSUPPORTED;
+	}
 
-	if (desc->mech_type == 0 && desc->load == 0 && desc->eject == 1)
+	if (desc->mech_type == 0 && desc->load == 0 && desc->eject == 1) {
+		kfree(buf);
 		return ODD_MECH_TYPE_SLOT;
-	else if (desc->mech_type == 1 && desc->load == 0 && desc->eject == 1)
+	} else if (desc->mech_type == 1 && desc->load == 0 &&
+		   desc->eject == 1) {
+		kfree(buf);
 		return ODD_MECH_TYPE_DRAWER;
-	else
+	} else {
+		kfree(buf);
 		return ODD_MECH_TYPE_UNSUPPORTED;
+	}
 }
 
 /* Test if ODD is zero power ready by sense code */
-- 
2.19.1

[PATCH AUTOSEL 5.0 75/98] kbuild: skip parsing pre sub-make code for recursion

[Sasha Levin]

From: Masahiro Yamada <yamada.masahiro@socionext.com>

[ Upstream commit 221cc2d27ddc49b3e06d4637db02bf78e70c573c ]

When Make recurses to the top Makefile with sub-make-done unset,
the code block surrounded by 'ifneq ($(sub-make-done),1) ... endif'
is parsed multiple times. This happens for in-tree building of
include/config/auto.conf, *-pkg, etc. with GNU Make 4.x.

This is a slight regression by commit 688931a5ad4e ("kbuild: skip
sub-make for in-tree build with GNU Make 4.x") in terms of performance
since that code block contains one $(shell ...) invocation.

Fix it by exporting the variable irrespective of sub-make being run.
I renamed it because GNU Make cannot properly export variables
containing hyphens. This is probably a bug of GNU Make, and the issue
in Kbuild had already been reported by commit 2bfbe7881ee0 ("kbuild:
Do not use hyphen in exported variable name").

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 Makefile | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)

diff --git a/Makefile b/Makefile
index ef192ca04330..ed3ad29d2db7 100644
--- a/Makefile
+++ b/Makefile
@@ -31,7 +31,7 @@ _all:
 # descending is started. They are now explicitly listed as the
 # prepare rule.
 
-ifneq ($(sub-make-done),1)
+ifneq ($(sub_make_done),1)
 
 # Do not use make's built-in rules and variables
 # (this increases performance and avoids hard-to-debug behaviour)
@@ -159,6 +159,8 @@ need-sub-make := 1
 $(lastword $(MAKEFILE_LIST)): ;
 endif
 
+export sub_make_done := 1
+
 ifeq ($(need-sub-make),1)
 
 PHONY += $(MAKECMDGOALS) sub-make
@@ -168,12 +170,12 @@ $(filter-out _all sub-make $(CURDIR)/Makefile, $(MAKECMDGOALS)) _all: sub-make
 
 # Invoke a second make in the output directory, passing relevant variables
 sub-make:
-	$(Q)$(MAKE) sub-make-done=1 \
+	$(Q)$(MAKE) \
 	$(if $(KBUILD_OUTPUT),-C $(KBUILD_OUTPUT) KBUILD_SRC=$(CURDIR)) \
 	-f $(CURDIR)/Makefile $(filter-out _all sub-make,$(MAKECMDGOALS))
 
 endif # need-sub-make
-endif # sub-make-done
+endif # sub_make_done
 
 # We process the rest of the Makefile if this is the final invocation of make
 ifeq ($(need-sub-make),)
-- 
2.19.1

[PATCH AUTOSEL 5.0 76/98] afs: Fix StoreData op marshalling

[Sasha Levin]

From: David Howells <dhowells@redhat.com>

[ Upstream commit 8c7ae38d1ce12a0eaeba655df8562552b3596c7f ]

The marshalling of AFS.StoreData, AFS.StoreData64 and YFS.StoreData64 calls
generated by ->setattr() ops for the purpose of expanding a file is
incorrect due to older documentation incorrectly describing the way the RPC
'FileLength' parameter is meant to work.

The older documentation says that this is the length the file is meant to
end up at the end of the operation; however, it was never implemented this
way in any of the servers, but rather the file is truncated down to this
before the write operation is effected, and never expanded to it (and,
indeed, it was renamed to 'TruncPos' in 2014).

Fix this by setting the position parameter to the new file length and doing
a zero-lengh write there.

The bug causes Xwayland to SIGBUS due to unexpected non-expansion of a file
it then mmaps.  This can be tested by giving the following test program a
filename in an AFS directory:

	#include <stdio.h>
	#include <stdlib.h>
	#include <unistd.h>
	#include <fcntl.h>
	#include <sys/mman.h>
	int main(int argc, char *argv[])
	{
		char *p;
		int fd;
		if (argc != 2) {
			fprintf(stderr,
				"Format: test-trunc-mmap <file>\n");
			exit(2);
		}
		fd = open(argv[1], O_RDWR | O_CREAT | O_TRUNC);
		if (fd < 0) {
			perror(argv[1]);
			exit(1);
		}
		if (ftruncate(fd, 0x140008) == -1) {
			perror("ftruncate");
			exit(1);
		}
		p = mmap(NULL, 4096, PROT_READ | PROT_WRITE,
			 MAP_SHARED, fd, 0);
		if (p == MAP_FAILED) {
			perror("mmap");
			exit(1);
		}
		p[0] = 'a';
		if (munmap(p, 4096) < 0) {
			perror("munmap");
			exit(1);
		}
		if (close(fd) < 0) {
			perror("close");
			exit(1);
		}
		exit(0);
	}

Fixes: 31143d5d515e ("AFS: implement basic file write support")
Reported-by: Jonathan Billings <jsbillin@umich.edu>
Tested-by: Jonathan Billings <jsbillin@umich.edu>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 fs/afs/fsclient.c  | 6 +++---
 fs/afs/yfsclient.c | 2 +-
 2 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/fs/afs/fsclient.c b/fs/afs/fsclient.c
index ca08c83168f5..0b37867b5c20 100644
--- a/fs/afs/fsclient.c
+++ b/fs/afs/fsclient.c
@@ -1515,8 +1515,8 @@ static int afs_fs_setattr_size64(struct afs_fs_cursor *fc, struct iattr *attr)
 
 	xdr_encode_AFS_StoreStatus(&bp, attr);
 
-	*bp++ = 0;				/* position of start of write */
-	*bp++ = 0;
+	*bp++ = htonl(attr->ia_size >> 32);	/* position of start of write */
+	*bp++ = htonl((u32) attr->ia_size);
 	*bp++ = 0;				/* size of write */
 	*bp++ = 0;
 	*bp++ = htonl(attr->ia_size >> 32);	/* new file length */
@@ -1564,7 +1564,7 @@ static int afs_fs_setattr_size(struct afs_fs_cursor *fc, struct iattr *attr)
 
 	xdr_encode_AFS_StoreStatus(&bp, attr);
 
-	*bp++ = 0;				/* position of start of write */
+	*bp++ = htonl(attr->ia_size);		/* position of start of write */
 	*bp++ = 0;				/* size of write */
 	*bp++ = htonl(attr->ia_size);		/* new file length */
 
diff --git a/fs/afs/yfsclient.c b/fs/afs/yfsclient.c
index 5aa57929e8c2..6e97a42d24d1 100644
--- a/fs/afs/yfsclient.c
+++ b/fs/afs/yfsclient.c
@@ -1514,7 +1514,7 @@ static int yfs_fs_setattr_size(struct afs_fs_cursor *fc, struct iattr *attr)
 	bp = xdr_encode_u32(bp, 0); /* RPC flags */
 	bp = xdr_encode_YFSFid(bp, &vnode->fid);
 	bp = xdr_encode_YFS_StoreStatus(bp, attr);
-	bp = xdr_encode_u64(bp, 0);		/* position of start of write */
+	bp = xdr_encode_u64(bp, attr->ia_size);	/* position of start of write */
 	bp = xdr_encode_u64(bp, 0);		/* size of write */
 	bp = xdr_encode_u64(bp, attr->ia_size);	/* new file length */
 	yfs_check_req(call, bp);
-- 
2.19.1

[PATCH AUTOSEL 5.0 77/98] gpio: of: Check propname before applying "cs-gpios" quirks

[Sasha Levin]

From: Andrey Smirnov <andrew.smirnov@gmail.com>

[ Upstream commit e5545c94e43b8f6599ffc01df8d1aedf18ee912a ]

SPI GPIO device has more than just "cs-gpio" property in its node and
would request those GPIOs as a part of its initialization. To avoid
applying CS-specific quirk to all of them add a check to make sure
that propname is "cs-gpios".

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/gpio/gpiolib-of.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/gpio/gpiolib-of.c b/drivers/gpio/gpiolib-of.c
index a1dd2f1c0d02..9470563f2506 100644
--- a/drivers/gpio/gpiolib-of.c
+++ b/drivers/gpio/gpiolib-of.c
@@ -119,7 +119,8 @@ static void of_gpio_flags_quirks(struct device_node *np,
 	 * to determine if the flags should have inverted semantics.
 	 */
 	if (IS_ENABLED(CONFIG_SPI_MASTER) &&
-	    of_property_read_bool(np, "cs-gpios")) {
+	    of_property_read_bool(np, "cs-gpios") &&
+	    !strcmp(propname, "cs-gpios")) {
 		struct device_node *child;
 		u32 cs;
 		int ret;
-- 
2.19.1

[PATCH AUTOSEL 5.0 78/98] gpio: of: Check for "spi-cs-high" in child instead of parent node

[Sasha Levin]

From: Andrey Smirnov <andrew.smirnov@gmail.com>

[ Upstream commit 7ce40277bf848391705011ba37eac2e377cbd9e6 ]

"spi-cs-high" is going to be specified in child node of an SPI
controller's representing attached SPI device, so change the code to
look for it there, instead of checking parent node.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/gpio/gpiolib-of.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/gpio/gpiolib-of.c b/drivers/gpio/gpiolib-of.c
index 9470563f2506..f1ae28289a67 100644
--- a/drivers/gpio/gpiolib-of.c
+++ b/drivers/gpio/gpiolib-of.c
@@ -142,16 +142,16 @@ static void of_gpio_flags_quirks(struct device_node *np,
 				 * conflict and the "spi-cs-high" flag will
 				 * take precedence.
 				 */
-				if (of_property_read_bool(np, "spi-cs-high")) {
+				if (of_property_read_bool(child, "spi-cs-high")) {
 					if (*flags & OF_GPIO_ACTIVE_LOW) {
 						pr_warn("%s GPIO handle specifies active low - ignored\n",
-							of_node_full_name(np));
+							of_node_full_name(child));
 						*flags &= ~OF_GPIO_ACTIVE_LOW;
 					}
 				} else {
 					if (!(*flags & OF_GPIO_ACTIVE_LOW))
 						pr_info("%s enforce active low on chipselect handle\n",
-							of_node_full_name(np));
+							of_node_full_name(child));
 					*flags |= OF_GPIO_ACTIVE_LOW;
 				}
 				break;
-- 
2.19.1

[PATCH AUTOSEL 5.0 79/98] KVM: nVMX: Do not inherit quadrant and invalid for the root shadow EPT

[Sasha Levin]

From: Sean Christopherson <sean.j.christopherson@intel.com>

[ Upstream commit 552c69b1dc714854a5f4e27d37a43c6d797adf7d ]

Explicitly zero out quadrant and invalid instead of inheriting them from
the root_mmu.  Functionally, this patch is a nop as we (should) never
set quadrant for a direct mapped (EPT) root_mmu and nested EPT is only
allowed if EPT is used for L1, and the root_mmu will never be invalid at
this point.

Explicitly setting flags sets the stage for repurposing the legacy
paging bits in role, e.g. nxe, cr0_wp, and sm{a,e}p_andnot_wp, at which
point 'smm' would be the only flag to be inherited from root_mmu.

Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 arch/x86/kvm/mmu.c | 13 +++++++++----
 1 file changed, 9 insertions(+), 4 deletions(-)

diff --git a/arch/x86/kvm/mmu.c b/arch/x86/kvm/mmu.c
index 9ab33cab9486..acab95dcffb6 100644
--- a/arch/x86/kvm/mmu.c
+++ b/arch/x86/kvm/mmu.c
@@ -4915,11 +4915,15 @@ static union kvm_mmu_role
 kvm_calc_shadow_ept_root_page_role(struct kvm_vcpu *vcpu, bool accessed_dirty,
 				   bool execonly)
 {
-	union kvm_mmu_role role;
+	union kvm_mmu_role role = {0};
+	union kvm_mmu_page_role root_base = vcpu->arch.root_mmu.mmu_role.base;
 
-	/* Base role is inherited from root_mmu */
-	role.base.word = vcpu->arch.root_mmu.mmu_role.base.word;
-	role.ext = kvm_calc_mmu_role_ext(vcpu);
+	/* Legacy paging and SMM flags are inherited from root_mmu */
+	role.base.smm = root_base.smm;
+	role.base.nxe = root_base.nxe;
+	role.base.cr0_wp = root_base.cr0_wp;
+	role.base.smep_andnot_wp = root_base.smep_andnot_wp;
+	role.base.smap_andnot_wp = root_base.smap_andnot_wp;
 
 	role.base.level = PT64_ROOT_4LEVEL;
 	role.base.direct = false;
@@ -4927,6 +4931,7 @@ kvm_calc_shadow_ept_root_page_role(struct kvm_vcpu *vcpu, bool accessed_dirty,
 	role.base.guest_mode = true;
 	role.base.access = ACC_ALL;
 
+	role.ext = kvm_calc_mmu_role_ext(vcpu);
 	role.ext.execonly = execonly;
 
 	return role;
-- 
2.19.1

[PATCH AUTOSEL 5.0 80/98] KVM: SVM: Workaround errata#1096 (insn_len maybe zero on SMAP violation)

[Sasha Levin]

From: "Singh, Brijesh" <brijesh.singh@amd.com>

[ Upstream commit 05d5a48635259e621ea26d01e8316c6feeb34190 ]

Errata#1096:

On a nested data page fault when CR.SMAP=1 and the guest data read
generates a SMAP violation, GuestInstrBytes field of the VMCB on a
VMEXIT will incorrectly return 0h instead the correct guest
instruction bytes .

Recommend Workaround:

To determine what instruction the guest was executing the hypervisor
will have to decode the instruction at the instruction pointer.

The recommended workaround can not be implemented for the SEV
guest because guest memory is encrypted with the guest specific key,
and instruction decoder will not be able to decode the instruction
bytes. If we hit this errata in the SEV guest then log the message
and request a guest shutdown.

Reported-by: Venkatesh Srinivas <venkateshs@google.com>
Cc: Jim Mattson <jmattson@google.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 arch/x86/include/asm/kvm_host.h |  2 ++
 arch/x86/kvm/mmu.c              |  8 +++++---
 arch/x86/kvm/svm.c              | 32 ++++++++++++++++++++++++++++++++
 arch/x86/kvm/vmx/vmx.c          |  6 ++++++
 4 files changed, 45 insertions(+), 3 deletions(-)

diff --git a/arch/x86/include/asm/kvm_host.h b/arch/x86/include/asm/kvm_host.h
index 71d763ad2637..9f2d890733a9 100644
--- a/arch/x86/include/asm/kvm_host.h
+++ b/arch/x86/include/asm/kvm_host.h
@@ -1198,6 +1198,8 @@ struct kvm_x86_ops {
 	int (*nested_enable_evmcs)(struct kvm_vcpu *vcpu,
 				   uint16_t *vmcs_version);
 	uint16_t (*nested_get_evmcs_version)(struct kvm_vcpu *vcpu);
+
+	bool (*need_emulation_on_page_fault)(struct kvm_vcpu *vcpu);
 };
 
 struct kvm_arch_async_pf {
diff --git a/arch/x86/kvm/mmu.c b/arch/x86/kvm/mmu.c
index acab95dcffb6..77dbb57412cc 100644
--- a/arch/x86/kvm/mmu.c
+++ b/arch/x86/kvm/mmu.c
@@ -5395,10 +5395,12 @@ emulate:
 	 * This can happen if a guest gets a page-fault on data access but the HW
 	 * table walker is not able to read the instruction page (e.g instruction
 	 * page is not present in memory). In those cases we simply restart the
-	 * guest.
+	 * guest, with the exception of AMD Erratum 1096 which is unrecoverable.
 	 */
-	if (unlikely(insn && !insn_len))
-		return 1;
+	if (unlikely(insn && !insn_len)) {
+		if (!kvm_x86_ops->need_emulation_on_page_fault(vcpu))
+			return 1;
+	}
 
 	er = x86_emulate_instruction(vcpu, cr2, emulation_type, insn, insn_len);
 
diff --git a/arch/x86/kvm/svm.c b/arch/x86/kvm/svm.c
index a9b8e38d78ad..3605c5cd5f1d 100644
--- a/arch/x86/kvm/svm.c
+++ b/arch/x86/kvm/svm.c
@@ -7098,6 +7098,36 @@ static int nested_enable_evmcs(struct kvm_vcpu *vcpu,
 	return -ENODEV;
 }
 
+static bool svm_need_emulation_on_page_fault(struct kvm_vcpu *vcpu)
+{
+	bool is_user, smap;
+
+	is_user = svm_get_cpl(vcpu) == 3;
+	smap = !kvm_read_cr4_bits(vcpu, X86_CR4_SMAP);
+
+	/*
+	 * Detect and workaround Errata 1096 Fam_17h_00_0Fh
+	 *
+	 * In non SEV guest, hypervisor will be able to read the guest
+	 * memory to decode the instruction pointer when insn_len is zero
+	 * so we return true to indicate that decoding is possible.
+	 *
+	 * But in the SEV guest, the guest memory is encrypted with the
+	 * guest specific key and hypervisor will not be able to decode the
+	 * instruction pointer so we will not able to workaround it. Lets
+	 * print the error and request to kill the guest.
+	 */
+	if (is_user && smap) {
+		if (!sev_guest(vcpu->kvm))
+			return true;
+
+		pr_err_ratelimited("KVM: Guest triggered AMD Erratum 1096\n");
+		kvm_make_request(KVM_REQ_TRIPLE_FAULT, vcpu);
+	}
+
+	return false;
+}
+
 static struct kvm_x86_ops svm_x86_ops __ro_after_init = {
 	.cpu_has_kvm_support = has_svm,
 	.disabled_by_bios = is_disabled,
@@ -7231,6 +7261,8 @@ static struct kvm_x86_ops svm_x86_ops __ro_after_init = {
 
 	.nested_enable_evmcs = nested_enable_evmcs,
 	.nested_get_evmcs_version = nested_get_evmcs_version,
+
+	.need_emulation_on_page_fault = svm_need_emulation_on_page_fault,
 };
 
 static int __init svm_init(void)
diff --git a/arch/x86/kvm/vmx/vmx.c b/arch/x86/kvm/vmx/vmx.c
index a0a770816429..7794c41a73bf 100644
--- a/arch/x86/kvm/vmx/vmx.c
+++ b/arch/x86/kvm/vmx/vmx.c
@@ -7522,6 +7522,11 @@ static int enable_smi_window(struct kvm_vcpu *vcpu)
 	return 0;
 }
 
+static bool vmx_need_emulation_on_page_fault(struct kvm_vcpu *vcpu)
+{
+	return 0;
+}
+
 static __init int hardware_setup(void)
 {
 	unsigned long host_bndcfgs;
@@ -7824,6 +7829,7 @@ static struct kvm_x86_ops vmx_x86_ops __ro_after_init = {
 	.set_nested_state = NULL,
 	.get_vmcs12_pages = NULL,
 	.nested_enable_evmcs = NULL,
+	.need_emulation_on_page_fault = vmx_need_emulation_on_page_fault,
 };
 
 static void vmx_cleanup_l1d_flush(void)
-- 
2.19.1

[PATCH AUTOSEL 5.0 81/98] kvm/x86: Move MSR_IA32_ARCH_CAPABILITIES to array emulated_msrs

[Sasha Levin]

From: Xiaoyao Li <xiaoyao.li@linux.intel.com>

[ Upstream commit 2bdb76c015df7125783d8394d6339d181cb5bc30 ]

Since MSR_IA32_ARCH_CAPABILITIES is emualted unconditionally even if
host doesn't suppot it. We should move it to array emulated_msrs from
arry msrs_to_save, to report to userspace that guest support this msr.

Signed-off-by: Xiaoyao Li <xiaoyao.li@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 arch/x86/kvm/x86.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/x86/kvm/x86.c b/arch/x86/kvm/x86.c
index 7ee802a92bc8..8748789b9540 100644
--- a/arch/x86/kvm/x86.c
+++ b/arch/x86/kvm/x86.c
@@ -1125,7 +1125,7 @@ static u32 msrs_to_save[] = {
 #endif
 	MSR_IA32_TSC, MSR_IA32_CR_PAT, MSR_VM_HSAVE_PA,
 	MSR_IA32_FEATURE_CONTROL, MSR_IA32_BNDCFGS, MSR_TSC_AUX,
-	MSR_IA32_SPEC_CTRL, MSR_IA32_ARCH_CAPABILITIES,
+	MSR_IA32_SPEC_CTRL,
 	MSR_IA32_RTIT_CTL, MSR_IA32_RTIT_STATUS, MSR_IA32_RTIT_CR3_MATCH,
 	MSR_IA32_RTIT_OUTPUT_BASE, MSR_IA32_RTIT_OUTPUT_MASK,
 	MSR_IA32_RTIT_ADDR0_A, MSR_IA32_RTIT_ADDR0_B,
@@ -1158,6 +1158,7 @@ static u32 emulated_msrs[] = {
 
 	MSR_IA32_TSC_ADJUST,
 	MSR_IA32_TSCDEADLINE,
+	MSR_IA32_ARCH_CAPABILITIES,
 	MSR_IA32_MISC_ENABLE,
 	MSR_IA32_MCG_STATUS,
 	MSR_IA32_MCG_CTL,
-- 
2.19.1

[PATCH AUTOSEL 5.0 82/98] x86/kvm/hyper-v: avoid spurious pending stimer on vCPU init

[Sasha Levin]

From: Vitaly Kuznetsov <vkuznets@redhat.com>

[ Upstream commit 013cc6ebbf41496ce4badedd71ea6d4a6d198c14 ]

When userspace initializes guest vCPUs it may want to zero all supported
MSRs including Hyper-V related ones including HV_X64_MSR_STIMERn_CONFIG/
HV_X64_MSR_STIMERn_COUNT. With commit f3b138c5d89a ("kvm/x86: Update SynIC
timers on guest entry only") we began doing stimer_mark_pending()
unconditionally on every config change.

The issue I'm observing manifests itself as following:
- Qemu writes 0 to STIMERn_{CONFIG,COUNT} MSRs and marks all stimers as
  pending in stimer_pending_bitmap, arms KVM_REQ_HV_STIMER;
- kvm_hv_has_stimer_pending() starts returning true;
- kvm_vcpu_has_events() starts returning true;
- kvm_arch_vcpu_runnable() starts returning true;
- when kvm_arch_vcpu_ioctl_run() gets into
  (vcpu->arch.mp_state == KVM_MP_STATE_UNINITIALIZED) case:
  - kvm_vcpu_block() gets in 'kvm_vcpu_check_block(vcpu) < 0' and returns
    immediately, avoiding normal wait path;
  - -EAGAIN is returned from kvm_arch_vcpu_ioctl_run() immediately forcing
    userspace to retry.

So instead of normal wait path we get a busy loop on all secondary vCPUs
before they get INIT signal. This seems to be undesirable, especially given
that this happens even when Hyper-V extensions are not used.

Generally, it seems to be pointless to mark an stimer as pending in
stimer_pending_bitmap and arm KVM_REQ_HV_STIMER as the only thing
kvm_hv_process_stimers() will do is clear the corresponding bit. We may
just not mark disabled timers as pending instead.

Fixes: f3b138c5d89a ("kvm/x86: Update SynIC timers on guest entry only")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 arch/x86/kvm/hyperv.c | 9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)

diff --git a/arch/x86/kvm/hyperv.c b/arch/x86/kvm/hyperv.c
index 89d20ed1d2e8..371c669696d7 100644
--- a/arch/x86/kvm/hyperv.c
+++ b/arch/x86/kvm/hyperv.c
@@ -526,7 +526,9 @@ static int stimer_set_config(struct kvm_vcpu_hv_stimer *stimer, u64 config,
 		new_config.enable = 0;
 	stimer->config.as_uint64 = new_config.as_uint64;
 
-	stimer_mark_pending(stimer, false);
+	if (stimer->config.enable)
+		stimer_mark_pending(stimer, false);
+
 	return 0;
 }
 
@@ -542,7 +544,10 @@ static int stimer_set_count(struct kvm_vcpu_hv_stimer *stimer, u64 count,
 		stimer->config.enable = 0;
 	else if (stimer->config.auto_enable)
 		stimer->config.enable = 1;
-	stimer_mark_pending(stimer, false);
+
+	if (stimer->config.enable)
+		stimer_mark_pending(stimer, false);
+
 	return 0;
 }
 
-- 
2.19.1

[PATCH AUTOSEL 5.0 83/98] KVM: selftests: assert on exit reason in CR4/cpuid sync test

[Sasha Levin]

From: Sean Christopherson <sean.j.christopherson@intel.com>

[ Upstream commit 8df98ae0ab2ead9a02228756eec26f8d7b17f499 ]

...so that the test doesn't end up in an infinite loop if it fails for
whatever reason, e.g. SHUTDOWN due to gcc inserting stack canary code
into ucall() and attempting to derefence a null segment.

Fixes: ca359066889f7 ("kvm: selftests: add cr4_cpuid_sync_test")
Cc: Wei Huang <wei@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 .../kvm/x86_64/cr4_cpuid_sync_test.c          | 35 ++++++++++---------
 1 file changed, 19 insertions(+), 16 deletions(-)

diff --git a/tools/testing/selftests/kvm/x86_64/cr4_cpuid_sync_test.c b/tools/testing/selftests/kvm/x86_64/cr4_cpuid_sync_test.c
index d503a51fad30..7c2c4d4055a8 100644
--- a/tools/testing/selftests/kvm/x86_64/cr4_cpuid_sync_test.c
+++ b/tools/testing/selftests/kvm/x86_64/cr4_cpuid_sync_test.c
@@ -87,22 +87,25 @@ int main(int argc, char *argv[])
 	while (1) {
 		rc = _vcpu_run(vm, VCPU_ID);
 
-		if (run->exit_reason == KVM_EXIT_IO) {
-			switch (get_ucall(vm, VCPU_ID, &uc)) {
-			case UCALL_SYNC:
-				/* emulate hypervisor clearing CR4.OSXSAVE */
-				vcpu_sregs_get(vm, VCPU_ID, &sregs);
-				sregs.cr4 &= ~X86_CR4_OSXSAVE;
-				vcpu_sregs_set(vm, VCPU_ID, &sregs);
-				break;
-			case UCALL_ABORT:
-				TEST_ASSERT(false, "Guest CR4 bit (OSXSAVE) unsynchronized with CPUID bit.");
-				break;
-			case UCALL_DONE:
-				goto done;
-			default:
-				TEST_ASSERT(false, "Unknown ucall 0x%x.", uc.cmd);
-			}
+		TEST_ASSERT(run->exit_reason == KVM_EXIT_IO,
+			    "Unexpected exit reason: %u (%s),\n",
+			    run->exit_reason,
+			    exit_reason_str(run->exit_reason));
+
+		switch (get_ucall(vm, VCPU_ID, &uc)) {
+		case UCALL_SYNC:
+			/* emulate hypervisor clearing CR4.OSXSAVE */
+			vcpu_sregs_get(vm, VCPU_ID, &sregs);
+			sregs.cr4 &= ~X86_CR4_OSXSAVE;
+			vcpu_sregs_set(vm, VCPU_ID, &sregs);
+			break;
+		case UCALL_ABORT:
+			TEST_ASSERT(false, "Guest CR4 bit (OSXSAVE) unsynchronized with CPUID bit.");
+			break;
+		case UCALL_DONE:
+			goto done;
+		default:
+			TEST_ASSERT(false, "Unknown ucall 0x%x.", uc.cmd);
 		}
 	}
 
-- 
2.19.1

[PATCH AUTOSEL 5.0 84/98] KVM: selftests: explicitly disable PIE for tests

[Sasha Levin]

From: Sean Christopherson <sean.j.christopherson@intel.com>

[ Upstream commit 0a3f29b5a77d6c27796d7a7adabafd199dc066d5 ]

KVM selftests embed the guest "image" as a function in the test itself
and extract the guest code at runtime by manually parsing the elf
headers.  The parsing is very simple and doesn't supporting fancy things
like position independent executables.  Recent versions of gcc enable
pie by default, which results in triple fault shutdowns in the guest due
to the virtual address in the headers not matching up with the virtual
address retrieved from the function pointer.

Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 tools/testing/selftests/kvm/Makefile | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/tools/testing/selftests/kvm/Makefile b/tools/testing/selftests/kvm/Makefile
index f9a0e9938480..212b8f0032ae 100644
--- a/tools/testing/selftests/kvm/Makefile
+++ b/tools/testing/selftests/kvm/Makefile
@@ -28,7 +28,7 @@ LIBKVM += $(LIBKVM_$(UNAME_M))
 INSTALL_HDR_PATH = $(top_srcdir)/usr
 LINUX_HDR_PATH = $(INSTALL_HDR_PATH)/include/
 LINUX_TOOL_INCLUDE = $(top_srcdir)/tools/include
-CFLAGS += -O2 -g -std=gnu99 -I$(LINUX_TOOL_INCLUDE) -I$(LINUX_HDR_PATH) -Iinclude -I$(<D) -Iinclude/$(UNAME_M) -I..
+CFLAGS += -O2 -g -std=gnu99 -no-pie -I$(LINUX_TOOL_INCLUDE) -I$(LINUX_HDR_PATH) -Iinclude -I$(<D) -Iinclude/$(UNAME_M) -I..
 LDFLAGS += -pthread
 
 # After inclusion, $(OUTPUT) is defined and
-- 
2.19.1

[PATCH AUTOSEL 5.0 85/98] KVM: selftests: disable stack protector for all KVM tests

[Sasha Levin]

From: Sean Christopherson <sean.j.christopherson@intel.com>

[ Upstream commit ffac839d040619847217647434b2b02469926871 ]

Since 4.8.3, gcc has enabled -fstack-protector by default.  This is
problematic for the KVM selftests as they do not configure fs or gs
segments (the stack canary is pulled from fs:0x28).  With the default
behavior, gcc will insert a stack canary on any function that creates
buffers of 8 bytes or more.  As a result, ucall() will hit a triple
fault shutdown due to reading a bad fs segment when inserting its
stack canary, i.e. every test fails with an unexpected SHUTDOWN.

Fixes: 14c47b7530e2d ("kvm: selftests: introduce ucall")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 tools/testing/selftests/kvm/Makefile | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/tools/testing/selftests/kvm/Makefile b/tools/testing/selftests/kvm/Makefile
index 212b8f0032ae..cb4a992d6dd3 100644
--- a/tools/testing/selftests/kvm/Makefile
+++ b/tools/testing/selftests/kvm/Makefile
@@ -28,8 +28,8 @@ LIBKVM += $(LIBKVM_$(UNAME_M))
 INSTALL_HDR_PATH = $(top_srcdir)/usr
 LINUX_HDR_PATH = $(INSTALL_HDR_PATH)/include/
 LINUX_TOOL_INCLUDE = $(top_srcdir)/tools/include
-CFLAGS += -O2 -g -std=gnu99 -no-pie -I$(LINUX_TOOL_INCLUDE) -I$(LINUX_HDR_PATH) -Iinclude -I$(<D) -Iinclude/$(UNAME_M) -I..
-LDFLAGS += -pthread
+CFLAGS += -O2 -g -std=gnu99 -fno-stack-protector -fno-PIE -I$(LINUX_TOOL_INCLUDE) -I$(LINUX_HDR_PATH) -Iinclude -I$(<D) -Iinclude/$(UNAME_M) -I..
+LDFLAGS += -pthread -no-pie
 
 # After inclusion, $(OUTPUT) is defined and
 # $(TEST_GEN_PROGS) starts with $(OUTPUT)/
-- 
2.19.1

[PATCH AUTOSEL 5.0 86/98] KVM: selftests: complete IO before migrating guest state

[Sasha Levin]

From: Sean Christopherson <sean.j.christopherson@intel.com>

[ Upstream commit 0f73bbc851ed32d22bbd86be09e0365c460bcd2e ]

Documentation/virtual/kvm/api.txt states:

  NOTE: For KVM_EXIT_IO, KVM_EXIT_MMIO, KVM_EXIT_OSI, KVM_EXIT_PAPR and
        KVM_EXIT_EPR the corresponding operations are complete (and guest
        state is consistent) only after userspace has re-entered the
        kernel with KVM_RUN.  The kernel side will first finish incomplete
        operations and then check for pending signals.  Userspace can
        re-enter the guest with an unmasked signal pending to complete
        pending operations.

Because guest state may be inconsistent, starting state migration after
an IO exit without first completing IO may result in test failures, e.g.
a proposed change to KVM's handling of %rip in its fast PIO handling[1]
will cause the new VM, i.e. the post-migration VM, to have its %rip set
to the IN instruction that triggered KVM_EXIT_IO, leading to a test
assertion due to a stage mismatch.

For simplicitly, require KVM_CAP_IMMEDIATE_EXIT to complete IO and skip
the test if it's not available.  The addition of KVM_CAP_IMMEDIATE_EXIT
predates the state selftest by more than a year.

[1] https://patchwork.kernel.org/patch/10848545/

Fixes: fa3899add1056 ("kvm: selftests: add basic test for state save and restore")
Reported-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 tools/testing/selftests/kvm/include/kvm_util.h |  1 +
 tools/testing/selftests/kvm/lib/kvm_util.c     | 16 ++++++++++++++++
 .../testing/selftests/kvm/x86_64/state_test.c  | 18 ++++++++++++++++--
 3 files changed, 33 insertions(+), 2 deletions(-)

diff --git a/tools/testing/selftests/kvm/include/kvm_util.h b/tools/testing/selftests/kvm/include/kvm_util.h
index a84785b02557..07b71ad9734a 100644
--- a/tools/testing/selftests/kvm/include/kvm_util.h
+++ b/tools/testing/selftests/kvm/include/kvm_util.h
@@ -102,6 +102,7 @@ vm_paddr_t addr_gva2gpa(struct kvm_vm *vm, vm_vaddr_t gva);
 struct kvm_run *vcpu_state(struct kvm_vm *vm, uint32_t vcpuid);
 void vcpu_run(struct kvm_vm *vm, uint32_t vcpuid);
 int _vcpu_run(struct kvm_vm *vm, uint32_t vcpuid);
+void vcpu_run_complete_io(struct kvm_vm *vm, uint32_t vcpuid);
 void vcpu_set_mp_state(struct kvm_vm *vm, uint32_t vcpuid,
 		       struct kvm_mp_state *mp_state);
 void vcpu_regs_get(struct kvm_vm *vm, uint32_t vcpuid, struct kvm_regs *regs);
diff --git a/tools/testing/selftests/kvm/lib/kvm_util.c b/tools/testing/selftests/kvm/lib/kvm_util.c
index b52cfdefecbf..efa0aad8b3c6 100644
--- a/tools/testing/selftests/kvm/lib/kvm_util.c
+++ b/tools/testing/selftests/kvm/lib/kvm_util.c
@@ -1121,6 +1121,22 @@ int _vcpu_run(struct kvm_vm *vm, uint32_t vcpuid)
 	return rc;
 }
 
+void vcpu_run_complete_io(struct kvm_vm *vm, uint32_t vcpuid)
+{
+	struct vcpu *vcpu = vcpu_find(vm, vcpuid);
+	int ret;
+
+	TEST_ASSERT(vcpu != NULL, "vcpu not found, vcpuid: %u", vcpuid);
+
+	vcpu->state->immediate_exit = 1;
+	ret = ioctl(vcpu->fd, KVM_RUN, NULL);
+	vcpu->state->immediate_exit = 0;
+
+	TEST_ASSERT(ret == -1 && errno == EINTR,
+		    "KVM_RUN IOCTL didn't exit immediately, rc: %i, errno: %i",
+		    ret, errno);
+}
+
 /*
  * VM VCPU Set MP State
  *
diff --git a/tools/testing/selftests/kvm/x86_64/state_test.c b/tools/testing/selftests/kvm/x86_64/state_test.c
index 4b3f556265f1..30f75856cf39 100644
--- a/tools/testing/selftests/kvm/x86_64/state_test.c
+++ b/tools/testing/selftests/kvm/x86_64/state_test.c
@@ -134,6 +134,11 @@ int main(int argc, char *argv[])
 
 	struct kvm_cpuid_entry2 *entry = kvm_get_supported_cpuid_entry(1);
 
+	if (!kvm_check_cap(KVM_CAP_IMMEDIATE_EXIT)) {
+		fprintf(stderr, "immediate_exit not available, skipping test\n");
+		exit(KSFT_SKIP);
+	}
+
 	/* Create VM */
 	vm = vm_create_default(VCPU_ID, 0, guest_code);
 	vcpu_set_cpuid(vm, VCPU_ID, kvm_get_supported_cpuid());
@@ -156,8 +161,6 @@ int main(int argc, char *argv[])
 			    stage, run->exit_reason,
 			    exit_reason_str(run->exit_reason));
 
-		memset(&regs1, 0, sizeof(regs1));
-		vcpu_regs_get(vm, VCPU_ID, &regs1);
 		switch (get_ucall(vm, VCPU_ID, &uc)) {
 		case UCALL_ABORT:
 			TEST_ASSERT(false, "%s at %s:%d", (const char *)uc.args[0],
@@ -176,6 +179,17 @@ int main(int argc, char *argv[])
 			    uc.args[1] == stage, "Unexpected register values vmexit #%lx, got %lx",
 			    stage, (ulong)uc.args[1]);
 
+		/*
+		 * When KVM exits to userspace with KVM_EXIT_IO, KVM guarantees
+		 * guest state is consistent only after userspace re-enters the
+		 * kernel with KVM_RUN.  Complete IO prior to migrating state
+		 * to a new VM.
+		 */
+		vcpu_run_complete_io(vm, VCPU_ID);
+
+		memset(&regs1, 0, sizeof(regs1));
+		vcpu_regs_get(vm, VCPU_ID, &regs1);
+
 		state = vcpu_save_state(vm, VCPU_ID);
 		kvm_vm_release(vm);
 
-- 
2.19.1

[PATCH AUTOSEL 5.0 87/98] gpio: of: Fix of_gpiochip_add() error path

[Sasha Levin]

From: Geert Uytterhoeven <geert+renesas@glider.be>

[ Upstream commit f7299d441a4da8a5088e651ea55023525a793a13 ]

If the call to of_gpiochip_scan_gpios() in of_gpiochip_add() fails, no
error handling is performed.  This lead to the need of callers to call
of_gpiochip_remove() on failure, which causes "BAD of_node_put() on ..."
if the failure happened before the call to of_node_get().

Fix this by adding proper error handling.

Note that calling gpiochip_remove_pin_ranges() multiple times causes no
harm: subsequent calls are a no-op.

Fixes: dfbd379ba9b7431e ("gpio: of: Return error if gpio hog configuration failed")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/gpio/gpiolib-of.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)

diff --git a/drivers/gpio/gpiolib-of.c b/drivers/gpio/gpiolib-of.c
index f1ae28289a67..13a402ede07a 100644
--- a/drivers/gpio/gpiolib-of.c
+++ b/drivers/gpio/gpiolib-of.c
@@ -712,7 +712,13 @@ int of_gpiochip_add(struct gpio_chip *chip)
 
 	of_node_get(chip->of_node);
 
-	return of_gpiochip_scan_gpios(chip);
+	status = of_gpiochip_scan_gpios(chip);
+	if (status) {
+		of_node_put(chip->of_node);
+		gpiochip_remove_pin_ranges(chip);
+	}
+
+	return status;
 }
 
 void of_gpiochip_remove(struct gpio_chip *chip)
-- 
2.19.1

[PATCH AUTOSEL 5.0 88/98] nvme-multipath: relax ANA state check

[Sasha Levin]

From: Martin George <marting@netapp.com>

[ Upstream commit cc2278c413c3a06a93c23ee8722e4dd3d621de12 ]

When undergoing state transitions I/O might be requeued, hence
we should always call nvme_mpath_set_live() to schedule requeue_work
whenever the nvme device is live, independent on whether the
old state was live or not.

Signed-off-by: Martin George <marting@netapp.com>
Signed-off-by: Gargi Srinivas <sring@netapp.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/nvme/host/multipath.c | 5 +----
 1 file changed, 1 insertion(+), 4 deletions(-)

diff --git a/drivers/nvme/host/multipath.c b/drivers/nvme/host/multipath.c
index b9fff3b8ed1b..23da7beadd62 100644
--- a/drivers/nvme/host/multipath.c
+++ b/drivers/nvme/host/multipath.c
@@ -366,15 +366,12 @@ static inline bool nvme_state_is_live(enum nvme_ana_state state)
 static void nvme_update_ns_ana_state(struct nvme_ana_group_desc *desc,
 		struct nvme_ns *ns)
 {
-	enum nvme_ana_state old;
-
 	mutex_lock(&ns->head->lock);
-	old = ns->ana_state;
 	ns->ana_grpid = le32_to_cpu(desc->grpid);
 	ns->ana_state = desc->state;
 	clear_bit(NVME_NS_ANA_PENDING, &ns->flags);
 
-	if (nvme_state_is_live(ns->ana_state) && !nvme_state_is_live(old))
+	if (nvme_state_is_live(ns->ana_state))
 		nvme_mpath_set_live(ns);
 	mutex_unlock(&ns->head->lock);
 }
-- 
2.19.1

[PATCH AUTOSEL 5.0 89/98] nvmet: fix building bvec from sg list

[Sasha Levin]

From: Ming Lei <ming.lei@redhat.com>

[ Upstream commit 02db99548d3608a625cf481cff2bb7b626829b3f ]

There are two mistakes for building bvec from sg list for file
backed ns:

- use request data length to compute number of io vector, this way
doesn't consider sg->offset, and the result may be smaller than required
io vectors

- bvec->bv_len isn't capped by sg->length

This patch fixes this issue by building bvec from sg directly, given
the whole IO stack is ready for multi-page bvec.

Reported-by: Yi Zhang <yi.zhang@redhat.com>
Fixes: 3a85a5de29ea ("nvme-loop: add a NVMe loopback host driver")

Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/nvme/target/io-cmd-file.c | 20 ++++++++++----------
 1 file changed, 10 insertions(+), 10 deletions(-)

diff --git a/drivers/nvme/target/io-cmd-file.c b/drivers/nvme/target/io-cmd-file.c
index 517522305e5c..9a0fa3943ca7 100644
--- a/drivers/nvme/target/io-cmd-file.c
+++ b/drivers/nvme/target/io-cmd-file.c
@@ -75,11 +75,11 @@ err:
 	return ret;
 }
 
-static void nvmet_file_init_bvec(struct bio_vec *bv, struct sg_page_iter *iter)
+static void nvmet_file_init_bvec(struct bio_vec *bv, struct scatterlist *sg)
 {
-	bv->bv_page = sg_page_iter_page(iter);
-	bv->bv_offset = iter->sg->offset;
-	bv->bv_len = PAGE_SIZE - iter->sg->offset;
+	bv->bv_page = sg_page(sg);
+	bv->bv_offset = sg->offset;
+	bv->bv_len = sg->length;
 }
 
 static ssize_t nvmet_file_submit_bvec(struct nvmet_req *req, loff_t pos,
@@ -128,14 +128,14 @@ static void nvmet_file_io_done(struct kiocb *iocb, long ret, long ret2)
 
 static bool nvmet_file_execute_io(struct nvmet_req *req, int ki_flags)
 {
-	ssize_t nr_bvec = DIV_ROUND_UP(req->data_len, PAGE_SIZE);
-	struct sg_page_iter sg_pg_iter;
+	ssize_t nr_bvec = req->sg_cnt;
 	unsigned long bv_cnt = 0;
 	bool is_sync = false;
 	size_t len = 0, total_len = 0;
 	ssize_t ret = 0;
 	loff_t pos;
-
+	int i;
+	struct scatterlist *sg;
 
 	if (req->f.mpool_alloc && nr_bvec > NVMET_MAX_MPOOL_BVEC)
 		is_sync = true;
@@ -147,8 +147,8 @@ static bool nvmet_file_execute_io(struct nvmet_req *req, int ki_flags)
 	}
 
 	memset(&req->f.iocb, 0, sizeof(struct kiocb));
-	for_each_sg_page(req->sg, &sg_pg_iter, req->sg_cnt, 0) {
-		nvmet_file_init_bvec(&req->f.bvec[bv_cnt], &sg_pg_iter);
+	for_each_sg(req->sg, sg, req->sg_cnt, i) {
+		nvmet_file_init_bvec(&req->f.bvec[bv_cnt], sg);
 		len += req->f.bvec[bv_cnt].bv_len;
 		total_len += req->f.bvec[bv_cnt].bv_len;
 		bv_cnt++;
@@ -225,7 +225,7 @@ static void nvmet_file_submit_buffered_io(struct nvmet_req *req)
 
 static void nvmet_file_execute_rw(struct nvmet_req *req)
 {
-	ssize_t nr_bvec = DIV_ROUND_UP(req->data_len, PAGE_SIZE);
+	ssize_t nr_bvec = req->sg_cnt;
 
 	if (!req->sg_cnt || !nr_bvec) {
 		nvmet_req_complete(req, 0);
-- 
2.19.1

[PATCH AUTOSEL 5.0 90/98] nvmet: fix error flow during ns enable

[Sasha Levin]

From: Max Gurtovoy <maxg@mellanox.com>

[ Upstream commit a536b49785759bf99465fdf6e248d34322123fcd ]

In case we fail to enable p2pmem on the current namespace, disable the
backing store device before exiting.

Cc: Stephen Bates <sbates@raithlin.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/nvme/target/core.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/nvme/target/core.c b/drivers/nvme/target/core.c
index 02c63c463222..7bad21a2283f 100644
--- a/drivers/nvme/target/core.c
+++ b/drivers/nvme/target/core.c
@@ -517,7 +517,7 @@ int nvmet_ns_enable(struct nvmet_ns *ns)
 
 	ret = nvmet_p2pmem_ns_enable(ns);
 	if (ret)
-		goto out_unlock;
+		goto out_dev_disable;
 
 	list_for_each_entry(ctrl, &subsys->ctrls, subsys_entry)
 		nvmet_p2pmem_ns_add_p2p(ctrl, ns);
@@ -558,7 +558,7 @@ out_unlock:
 out_dev_put:
 	list_for_each_entry(ctrl, &subsys->ctrls, subsys_entry)
 		pci_dev_put(radix_tree_delete(&ctrl->p2p_ns_map, ns->nsid));
-
+out_dev_disable:
 	nvmet_ns_dev_disable(ns);
 	goto out_unlock;
 }
-- 
2.19.1

[PATCH AUTOSEL 5.0 91/98] perf cs-etm: Add missing case value

[Sasha Levin]

From: Solomon Tan <solomonbobstoner@gmail.com>

[ Upstream commit c8fa7a807f3c5f946bd92076fbaf7826edb650dc ]

The following error was thrown when compiling `tools/perf` using OpenCSD
v0.11.1. This patch fixes said error.

    CC       util/intel-pt-decoder/intel-pt-log.o
    CC       util/cs-etm-decoder/cs-etm-decoder.o
  util/cs-etm-decoder/cs-etm-decoder.c: In function
  ‘cs_etm_decoder__buffer_range’:
  util/cs-etm-decoder/cs-etm-decoder.c:370:2: error: enumeration value
  ‘OCSD_INSTR_WFI_WFE’ not handled in switch [-Werror=switch-enum]
    switch (elem->last_i_type) {
    ^~~~~~
    CC       util/intel-pt-decoder/intel-pt-decoder.o
  cc1: all warnings being treated as errors

Because `OCSD_INSTR_WFI_WFE` case was added only in v0.11.0, the minimum
required OpenCSD library version for this patch is no longer v0.10.0.

Signed-off-by: Solomon Tan <solomonbobstoner@gmail.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Robert Walker <robert.walker@arm.com>
Cc: Suzuki K Poulouse <suzuki.poulose@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/20190322052255.GA4809@w-OptiPlex-7050
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 tools/build/feature/test-libopencsd.c           | 4 ++--
 tools/perf/util/cs-etm-decoder/cs-etm-decoder.c | 1 +
 2 files changed, 3 insertions(+), 2 deletions(-)

diff --git a/tools/build/feature/test-libopencsd.c b/tools/build/feature/test-libopencsd.c
index d68eb4fb40cc..2b0e02c38870 100644
--- a/tools/build/feature/test-libopencsd.c
+++ b/tools/build/feature/test-libopencsd.c
@@ -4,9 +4,9 @@
 /*
  * Check OpenCSD library version is sufficient to provide required features
  */
-#define OCSD_MIN_VER ((0 << 16) | (10 << 8) | (0))
+#define OCSD_MIN_VER ((0 << 16) | (11 << 8) | (0))
 #if !defined(OCSD_VER_NUM) || (OCSD_VER_NUM < OCSD_MIN_VER)
-#error "OpenCSD >= 0.10.0 is required"
+#error "OpenCSD >= 0.11.0 is required"
 #endif
 
 int main(void)
diff --git a/tools/perf/util/cs-etm-decoder/cs-etm-decoder.c b/tools/perf/util/cs-etm-decoder/cs-etm-decoder.c
index 8c155575c6c5..2a8bf6b45a30 100644
--- a/tools/perf/util/cs-etm-decoder/cs-etm-decoder.c
+++ b/tools/perf/util/cs-etm-decoder/cs-etm-decoder.c
@@ -374,6 +374,7 @@ cs_etm_decoder__buffer_range(struct cs_etm_decoder *decoder,
 		break;
 	case OCSD_INSTR_ISB:
 	case OCSD_INSTR_DSB_DMB:
+	case OCSD_INSTR_WFI_WFE:
 	case OCSD_INSTR_OTHER:
 	default:
 		packet->last_instr_taken_branch = false;
-- 
2.19.1

[PATCH AUTOSEL 5.0 92/98] perf machine: Update kernel map address and re-order properly

[Sasha Levin]

From: Wei Li <liwei391@huawei.com>

[ Upstream commit 977c7a6d1e263ff1d755f28595b99e4bc0c48a9f ]

Since commit 1fb87b8e9599 ("perf machine: Don't search for active kernel
start in __machine__create_kernel_maps"), the __machine__create_kernel_maps()
just create a map what start and end are both zero. Though the address will be
updated later, the order of map in the rbtree may be incorrect.

The commit ee05d21791db ("perf machine: Set main kernel end address properly")
fixed the logic in machine__create_kernel_maps(), but it's still wrong in
function machine__process_kernel_mmap_event().

To reproduce this issue, we need an environment which the module address
is before the kernel text segment. I tested it on an aarch64 machine with
kernel 4.19.25:

  [root@localhost hulk]# grep _stext /proc/kallsyms
  ffff000008081000 T _stext
  [root@localhost hulk]# grep _etext /proc/kallsyms
  ffff000009780000 R _etext
  [root@localhost hulk]# tail /proc/modules
  hisi_sas_v2_hw 77824 0 - Live 0xffff00000191d000
  nvme_core 126976 7 nvme, Live 0xffff0000018b6000
  mdio 20480 1 ixgbe, Live 0xffff0000018ab000
  hisi_sas_main 106496 1 hisi_sas_v2_hw, Live 0xffff000001861000
  hns_mdio 20480 2 - Live 0xffff000001822000
  hnae 28672 3 hns_dsaf,hns_enet_drv, Live 0xffff000001815000
  dm_mirror 40960 0 - Live 0xffff000001804000
  dm_region_hash 32768 1 dm_mirror, Live 0xffff0000017f5000
  dm_log 32768 2 dm_mirror,dm_region_hash, Live 0xffff0000017e7000
  dm_mod 315392 17 dm_mirror,dm_log, Live 0xffff000001780000
  [root@localhost hulk]#

Before fix:

  [root@localhost bin]# perf record sleep 3
  [ perf record: Woken up 1 times to write data ]
  [ perf record: Captured and wrote 0.011 MB perf.data (9 samples) ]
  [root@localhost bin]# perf buildid-list -i perf.data
  4c4e46c971ca935f781e603a09b52a92e8bdfee8 [vdso]
  [root@localhost bin]# perf buildid-list -i perf.data -H
  0000000000000000000000000000000000000000 /proc/kcore
  [root@localhost bin]#

After fix:

  [root@localhost tools]# ./perf/perf record sleep 3
  [ perf record: Woken up 1 times to write data ]
  [ perf record: Captured and wrote 0.011 MB perf.data (9 samples) ]
  [root@localhost tools]# ./perf/perf buildid-list -i perf.data
  28a6c690262896dbd1b5e1011ed81623e6db0610 [kernel.kallsyms]
  106c14ce6e4acea3453e484dc604d66666f08a2f [vdso]
  [root@localhost tools]# ./perf/perf buildid-list -i perf.data -H
  28a6c690262896dbd1b5e1011ed81623e6db0610 /proc/kcore

Signed-off-by: Wei Li <liwei391@huawei.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Kim Phillips <kim.phillips@arm.com>
Cc: Li Bin <huawei.libin@huawei.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20190228092003.34071-1-liwei391@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 tools/perf/util/machine.c | 32 ++++++++++++++++++++------------
 1 file changed, 20 insertions(+), 12 deletions(-)

diff --git a/tools/perf/util/machine.c b/tools/perf/util/machine.c
index 143f7057d581..596db1daee35 100644
--- a/tools/perf/util/machine.c
+++ b/tools/perf/util/machine.c
@@ -1358,6 +1358,20 @@ static void machine__set_kernel_mmap(struct machine *machine,
 		machine->vmlinux_map->end = ~0ULL;
 }
 
+static void machine__update_kernel_mmap(struct machine *machine,
+				     u64 start, u64 end)
+{
+	struct map *map = machine__kernel_map(machine);
+
+	map__get(map);
+	map_groups__remove(&machine->kmaps, map);
+
+	machine__set_kernel_mmap(machine, start, end);
+
+	map_groups__insert(&machine->kmaps, map);
+	map__put(map);
+}
+
 int machine__create_kernel_maps(struct machine *machine)
 {
 	struct dso *kernel = machine__get_kernel(machine);
@@ -1390,17 +1404,11 @@ int machine__create_kernel_maps(struct machine *machine)
 			goto out_put;
 		}
 
-		/* we have a real start address now, so re-order the kmaps */
-		map = machine__kernel_map(machine);
-
-		map__get(map);
-		map_groups__remove(&machine->kmaps, map);
-
-		/* assume it's the last in the kmaps */
-		machine__set_kernel_mmap(machine, addr, ~0ULL);
-
-		map_groups__insert(&machine->kmaps, map);
-		map__put(map);
+		/*
+		 * we have a real start address now, so re-order the kmaps
+		 * assume it's the last in the kmaps
+		 */
+		machine__update_kernel_mmap(machine, addr, ~0ULL);
 	}
 
 	if (machine__create_extra_kernel_maps(machine, kernel))
@@ -1536,7 +1544,7 @@ static int machine__process_kernel_mmap_event(struct machine *machine,
 		if (strstr(kernel->long_name, "vmlinux"))
 			dso__set_short_name(kernel, "[kernel.vmlinux]", false);
 
-		machine__set_kernel_mmap(machine, event->mmap.start,
+		machine__update_kernel_mmap(machine, event->mmap.start,
 					 event->mmap.start + event->mmap.len);
 
 		/*
-- 
2.19.1

[PATCH AUTOSEL 5.0 93/98] kconfig/[mn]conf: handle backspace (^H) key

[Sasha Levin]

From: Changbin Du <changbin.du@gmail.com>

[ Upstream commit 9c38f1f044080392603c497ecca4d7d09876ff99 ]

Backspace is not working on some terminal emulators which do not send the
key code defined by terminfo. Terminals either send '^H' (8) or '^?' (127).
But currently only '^?' is handled. Let's also handle '^H' for those
terminals.

Signed-off-by: Changbin Du <changbin.du@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 scripts/kconfig/lxdialog/inputbox.c | 3 ++-
 scripts/kconfig/nconf.c             | 2 +-
 scripts/kconfig/nconf.gui.c         | 3 ++-
 3 files changed, 5 insertions(+), 3 deletions(-)

diff --git a/scripts/kconfig/lxdialog/inputbox.c b/scripts/kconfig/lxdialog/inputbox.c
index 611945611bf8..1dcfb288ee63 100644
--- a/scripts/kconfig/lxdialog/inputbox.c
+++ b/scripts/kconfig/lxdialog/inputbox.c
@@ -113,7 +113,8 @@ do_resize:
 			case KEY_DOWN:
 				break;
 			case KEY_BACKSPACE:
-			case 127:
+			case 8:   /* ^H */
+			case 127: /* ^? */
 				if (pos) {
 					wattrset(dialog, dlg.inputbox.atr);
 					if (input_x == 0) {
diff --git a/scripts/kconfig/nconf.c b/scripts/kconfig/nconf.c
index a4670f4e825a..ac92c0ded6c5 100644
--- a/scripts/kconfig/nconf.c
+++ b/scripts/kconfig/nconf.c
@@ -1048,7 +1048,7 @@ static int do_match(int key, struct match_state *state, int *ans)
 		state->match_direction = FIND_NEXT_MATCH_UP;
 		*ans = get_mext_match(state->pattern,
 				state->match_direction);
-	} else if (key == KEY_BACKSPACE || key == 127) {
+	} else if (key == KEY_BACKSPACE || key == 8 || key == 127) {
 		state->pattern[strlen(state->pattern)-1] = '\0';
 		adj_match_dir(&state->match_direction);
 	} else
diff --git a/scripts/kconfig/nconf.gui.c b/scripts/kconfig/nconf.gui.c
index 7be620a1fcdb..77f525a8617c 100644
--- a/scripts/kconfig/nconf.gui.c
+++ b/scripts/kconfig/nconf.gui.c
@@ -439,7 +439,8 @@ int dialog_inputbox(WINDOW *main_window,
 		case KEY_F(F_EXIT):
 		case KEY_F(F_BACK):
 			break;
-		case 127:
+		case 8:   /* ^H */
+		case 127: /* ^? */
 		case KEY_BACKSPACE:
 			if (cursor_position > 0) {
 				memmove(&result[cursor_position-1],
-- 
2.19.1

[PATCH AUTOSEL 5.0 94/98] iommu/amd: Reserve exclusion range in iova-domain

[Sasha Levin]

From: Joerg Roedel <jroedel@suse.de>

[ Upstream commit 8aafaaf2212192012f5bae305bb31cdf7681d777 ]

If a device has an exclusion range specified in the IVRS
table, this region needs to be reserved in the iova-domain
of that device. This hasn't happened until now and can cause
data corruption on data transfered with these devices.

Treat exclusion ranges as reserved regions in the iommu-core
to fix the problem.

Fixes: be2a022c0dd0 ('x86, AMD IOMMU: add functions to parse IOMMU memory mapping requirements for devices')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/iommu/amd_iommu.c       | 9 ++++++---
 drivers/iommu/amd_iommu_init.c  | 7 ++++---
 drivers/iommu/amd_iommu_types.h | 2 ++
 3 files changed, 12 insertions(+), 6 deletions(-)

diff --git a/drivers/iommu/amd_iommu.c b/drivers/iommu/amd_iommu.c
index e628ef23418f..55b3e4b9d5dc 100644
--- a/drivers/iommu/amd_iommu.c
+++ b/drivers/iommu/amd_iommu.c
@@ -3166,21 +3166,24 @@ static void amd_iommu_get_resv_regions(struct device *dev,
 		return;
 
 	list_for_each_entry(entry, &amd_iommu_unity_map, list) {
+		int type, prot = 0;
 		size_t length;
-		int prot = 0;
 
 		if (devid < entry->devid_start || devid > entry->devid_end)
 			continue;
 
+		type   = IOMMU_RESV_DIRECT;
 		length = entry->address_end - entry->address_start;
 		if (entry->prot & IOMMU_PROT_IR)
 			prot |= IOMMU_READ;
 		if (entry->prot & IOMMU_PROT_IW)
 			prot |= IOMMU_WRITE;
+		if (entry->prot & IOMMU_UNITY_MAP_FLAG_EXCL_RANGE)
+			/* Exclusion range */
+			type = IOMMU_RESV_RESERVED;
 
 		region = iommu_alloc_resv_region(entry->address_start,
-						 length, prot,
-						 IOMMU_RESV_DIRECT);
+						 length, prot, type);
 		if (!region) {
 			pr_err("Out of memory allocating dm-regions for %s\n",
 				dev_name(dev));
diff --git a/drivers/iommu/amd_iommu_init.c b/drivers/iommu/amd_iommu_init.c
index 66123b911ec8..84fa5b22371e 100644
--- a/drivers/iommu/amd_iommu_init.c
+++ b/drivers/iommu/amd_iommu_init.c
@@ -2013,6 +2013,9 @@ static int __init init_unity_map_range(struct ivmd_header *m)
 	if (e == NULL)
 		return -ENOMEM;
 
+	if (m->flags & IVMD_FLAG_EXCL_RANGE)
+		init_exclusion_range(m);
+
 	switch (m->type) {
 	default:
 		kfree(e);
@@ -2059,9 +2062,7 @@ static int __init init_memory_definitions(struct acpi_table_header *table)
 
 	while (p < end) {
 		m = (struct ivmd_header *)p;
-		if (m->flags & IVMD_FLAG_EXCL_RANGE)
-			init_exclusion_range(m);
-		else if (m->flags & IVMD_FLAG_UNITY_MAP)
+		if (m->flags & (IVMD_FLAG_UNITY_MAP | IVMD_FLAG_EXCL_RANGE))
 			init_unity_map_range(m);
 
 		p += m->length;
diff --git a/drivers/iommu/amd_iommu_types.h b/drivers/iommu/amd_iommu_types.h
index eae0741f72dc..87965e4d9647 100644
--- a/drivers/iommu/amd_iommu_types.h
+++ b/drivers/iommu/amd_iommu_types.h
@@ -374,6 +374,8 @@
 #define IOMMU_PROT_IR 0x01
 #define IOMMU_PROT_IW 0x02
 
+#define IOMMU_UNITY_MAP_FLAG_EXCL_RANGE	(1 << 2)
+
 /* IOMMU capabilities */
 #define IOMMU_CAP_IOTLB   24
 #define IOMMU_CAP_NPCACHE 26
-- 
2.19.1

[PATCH AUTOSEL 5.0 95/98] kasan: fix variable 'tag' set but not used warning

[Sasha Levin]

From: Qian Cai <cai@lca.pw>

[ Upstream commit c412a769d2452161e97f163c4c4f31efc6626f06 ]

set_tag() compiles away when CONFIG_KASAN_SW_TAGS=n, so make
arch_kasan_set_tag() a static inline function to fix warnings below.

  mm/kasan/common.c: In function '__kasan_kmalloc':
  mm/kasan/common.c:475:5: warning: variable 'tag' set but not used [-Wunused-but-set-variable]
    u8 tag;
       ^~~

Link: http://lkml.kernel.org/r/20190307185244.54648-1-cai@lca.pw
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 mm/kasan/kasan.h | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/mm/kasan/kasan.h b/mm/kasan/kasan.h
index ea51b2d898ec..c980ce43e3ba 100644
--- a/mm/kasan/kasan.h
+++ b/mm/kasan/kasan.h
@@ -164,7 +164,10 @@ static inline u8 random_tag(void)
 #endif
 
 #ifndef arch_kasan_set_tag
-#define arch_kasan_set_tag(addr, tag)	((void *)(addr))
+static inline const void *arch_kasan_set_tag(const void *addr, u8 tag)
+{
+	return addr;
+}
 #endif
 #ifndef arch_kasan_reset_tag
 #define arch_kasan_reset_tag(addr)	((void *)(addr))
-- 
2.19.1

[PATCH AUTOSEL 5.0 96/98] ptrace: take into account saved_sigmask in PTRACE{GET,SET}SIGMASK

[Sasha Levin]

From: Andrei Vagin <avagin@gmail.com>

[ Upstream commit fcfc2aa0185f4a731d05a21e9f359968fdfd02e7 ]

There are a few system calls (pselect, ppoll, etc) which replace a task
sigmask while they are running in a kernel-space

When a task calls one of these syscalls, the kernel saves a current
sigmask in task->saved_sigmask and sets a syscall sigmask.

On syscall-exit-stop, ptrace traps a task before restoring the
saved_sigmask, so PTRACE_GETSIGMASK returns the syscall sigmask and
PTRACE_SETSIGMASK does nothing, because its sigmask is replaced by
saved_sigmask, when the task returns to user-space.

This patch fixes this problem.  PTRACE_GETSIGMASK returns saved_sigmask
if it's set.  PTRACE_SETSIGMASK drops the TIF_RESTORE_SIGMASK flag.

Link: http://lkml.kernel.org/r/20181120060616.6043-1-avagin@gmail.com
Fixes: 29000caecbe8 ("ptrace: add ability to get/set signal-blocked mask")
Signed-off-by: Andrei Vagin <avagin@gmail.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 include/linux/sched/signal.h | 18 ++++++++++++++++++
 kernel/ptrace.c              | 15 +++++++++++++--
 2 files changed, 31 insertions(+), 2 deletions(-)

diff --git a/include/linux/sched/signal.h b/include/linux/sched/signal.h
index 13789d10a50e..76b8399b17f6 100644
--- a/include/linux/sched/signal.h
+++ b/include/linux/sched/signal.h
@@ -417,10 +417,20 @@ static inline void set_restore_sigmask(void)
 	set_thread_flag(TIF_RESTORE_SIGMASK);
 	WARN_ON(!test_thread_flag(TIF_SIGPENDING));
 }
+
+static inline void clear_tsk_restore_sigmask(struct task_struct *tsk)
+{
+	clear_tsk_thread_flag(tsk, TIF_RESTORE_SIGMASK);
+}
+
 static inline void clear_restore_sigmask(void)
 {
 	clear_thread_flag(TIF_RESTORE_SIGMASK);
 }
+static inline bool test_tsk_restore_sigmask(struct task_struct *tsk)
+{
+	return test_tsk_thread_flag(tsk, TIF_RESTORE_SIGMASK);
+}
 static inline bool test_restore_sigmask(void)
 {
 	return test_thread_flag(TIF_RESTORE_SIGMASK);
@@ -438,6 +448,10 @@ static inline void set_restore_sigmask(void)
 	current->restore_sigmask = true;
 	WARN_ON(!test_thread_flag(TIF_SIGPENDING));
 }
+static inline void clear_tsk_restore_sigmask(struct task_struct *tsk)
+{
+	tsk->restore_sigmask = false;
+}
 static inline void clear_restore_sigmask(void)
 {
 	current->restore_sigmask = false;
@@ -446,6 +460,10 @@ static inline bool test_restore_sigmask(void)
 {
 	return current->restore_sigmask;
 }
+static inline bool test_tsk_restore_sigmask(struct task_struct *tsk)
+{
+	return tsk->restore_sigmask;
+}
 static inline bool test_and_clear_restore_sigmask(void)
 {
 	if (!current->restore_sigmask)
diff --git a/kernel/ptrace.c b/kernel/ptrace.c
index 771e93f9c43f..6f357f4fc859 100644
--- a/kernel/ptrace.c
+++ b/kernel/ptrace.c
@@ -29,6 +29,7 @@
 #include <linux/hw_breakpoint.h>
 #include <linux/cn_proc.h>
 #include <linux/compat.h>
+#include <linux/sched/signal.h>
 
 /*
  * Access another process' address space via ptrace.
@@ -924,18 +925,26 @@ int ptrace_request(struct task_struct *child, long request,
 			ret = ptrace_setsiginfo(child, &siginfo);
 		break;
 
-	case PTRACE_GETSIGMASK:
+	case PTRACE_GETSIGMASK: {
+		sigset_t *mask;
+
 		if (addr != sizeof(sigset_t)) {
 			ret = -EINVAL;
 			break;
 		}
 
-		if (copy_to_user(datavp, &child->blocked, sizeof(sigset_t)))
+		if (test_tsk_restore_sigmask(child))
+			mask = &child->saved_sigmask;
+		else
+			mask = &child->blocked;
+
+		if (copy_to_user(datavp, mask, sizeof(sigset_t)))
 			ret = -EFAULT;
 		else
 			ret = 0;
 
 		break;
+	}
 
 	case PTRACE_SETSIGMASK: {
 		sigset_t new_set;
@@ -961,6 +970,8 @@ int ptrace_request(struct task_struct *child, long request,
 		child->blocked = new_set;
 		spin_unlock_irq(&child->sighand->siglock);
 
+		clear_tsk_restore_sigmask(child);
+
 		ret = 0;
 		break;
 	}
-- 
2.19.1

[PATCH AUTOSEL 5.0 97/98] leds: pca9532: fix a potential NULL pointer dereference

[Sasha Levin]

From: Kangjie Lu <kjlu@umn.edu>

[ Upstream commit 0aab8e4df4702b31314a27ec4b0631dfad0fae0a ]

In case of_match_device cannot find a match, return -EINVAL to avoid
NULL pointer dereference.

Fixes: fa4191a609f2 ("leds: pca9532: Add device tree support")
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/leds/leds-pca9532.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/drivers/leds/leds-pca9532.c b/drivers/leds/leds-pca9532.c
index 7fea18b0c15d..7cb4d685a1f1 100644
--- a/drivers/leds/leds-pca9532.c
+++ b/drivers/leds/leds-pca9532.c
@@ -513,6 +513,7 @@ static int pca9532_probe(struct i2c_client *client,
 	const struct i2c_device_id *id)
 {
 	int devid;
+	const struct of_device_id *of_id;
 	struct pca9532_data *data = i2c_get_clientdata(client);
 	struct pca9532_platform_data *pca9532_pdata =
 			dev_get_platdata(&client->dev);
@@ -528,8 +529,11 @@ static int pca9532_probe(struct i2c_client *client,
 			dev_err(&client->dev, "no platform data\n");
 			return -EINVAL;
 		}
-		devid = (int)(uintptr_t)of_match_device(
-			of_pca9532_leds_match, &client->dev)->data;
+		of_id = of_match_device(of_pca9532_leds_match,
+				&client->dev);
+		if (unlikely(!of_id))
+			return -EINVAL;
+		devid = (int)(uintptr_t) of_id->data;
 	} else {
 		devid = id->driver_data;
 	}
-- 
2.19.1

[PATCH AUTOSEL 5.0 98/98] leds: trigger: netdev: use memcpy in device_name_store

[Sasha Levin]

From: Rasmus Villemoes <linux@rasmusvillemoes.dk>

[ Upstream commit 909346433064b8d840dc82af26161926b8d37558 ]

If userspace doesn't end the input with a newline (which can easily
happen if the write happens from a C program that does write(fd,
iface, strlen(iface))), we may end up including garbage from a
previous, longer value in the device_name. For example

# cat device_name

# printf 'eth12' > device_name
# cat device_name
eth12
# printf 'eth3' > device_name
# cat device_name
eth32

I highly doubt anybody is relying on this behaviour, so switch to
simply copying the bytes (we've already checked that size is <
IFNAMSIZ) and unconditionally zero-terminate it; of course, we also
still have to strip a trailing newline.

This is also preparation for future patches.

Fixes: 06f502f57d0d ("leds: trigger: Introduce a NETDEV trigger")
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/leds/trigger/ledtrig-netdev.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/leds/trigger/ledtrig-netdev.c b/drivers/leds/trigger/ledtrig-netdev.c
index 167a94c02d05..136f86a1627d 100644
--- a/drivers/leds/trigger/ledtrig-netdev.c
+++ b/drivers/leds/trigger/ledtrig-netdev.c
@@ -122,7 +122,8 @@ static ssize_t device_name_store(struct device *dev,
 		trigger_data->net_dev = NULL;
 	}
 
-	strncpy(trigger_data->device_name, buf, size);
+	memcpy(trigger_data->device_name, buf, size);
+	trigger_data->device_name[size] = 0;
 	if (size > 0 && trigger_data->device_name[size - 1] == '\n')
 		trigger_data->device_name[size - 1] = 0;
 
-- 
2.19.1

Re: [PATCH AUTOSEL 5.0 70/98] tty: fix NULL pointer issue when tty_port ops is not set

[Greg Kroah-Hartman]

On Mon, Apr 22, 2019 at 03:41:37PM -0400, Sasha Levin wrote:
> From: Fabien Dessenne <fabien.dessenne@st.com>
> 
> [ Upstream commit f4e68d58cf2b20a581759bbc7228052534652673 ]
> 
> Unlike 'client_ops' which is initialized to 'default_client_ops', the
> port operations 'ops' may be left to NULL.
> Check the 'ops' value before checking the 'ops->x' value.
> 
> Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
> Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
> ---
>  drivers/tty/tty_port.c | 10 +++++-----
>  1 file changed, 5 insertions(+), 5 deletions(-)

Nope, I have a revert for this in my tree for 5.2-rc1, no need for this
in any stable tree, it doesn't do anything :)

Please drop it from all branches, thanks.

greg k-h

Re: [PATCH AUTOSEL 5.0 61/98] libceph: fix breakage caused by multipage bvecs

[Ilya Dryomov]

On Mon, Apr 22, 2019 at 9:44 PM Sasha Levin <sashal@kernel.org> wrote:
>
> From: Ilya Dryomov <idryomov@gmail.com>
>
> [ Upstream commit 187df76325af5d9e12ae9daec1510307797e54f0 ]
>
> A bvec can now consist of multiple physically contiguous pages.
> This means that bvec_iter_advance() can move to a different page while
> staying in the same bvec (i.e. ->bi_bvec_done != 0).
>
> The messenger works in terms of segments which can now be defined as
> the smaller of a bvec and a page.  The "more bytes to process in this
> segment" condition holds only if bvec_iter_advance() leaves us in the
> same bvec _and_ in the same page.  On next bvec (possibly in the same
> page) and on next page (possibly in the same bvec) we may need to set
> ->last_piece.
>
> Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
> Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
> ---
>  net/ceph/messenger.c | 8 ++++++--
>  1 file changed, 6 insertions(+), 2 deletions(-)
>
> diff --git a/net/ceph/messenger.c b/net/ceph/messenger.c
> index 7e71b0df1fbc..3083988ce729 100644
> --- a/net/ceph/messenger.c
> +++ b/net/ceph/messenger.c
> @@ -840,6 +840,7 @@ static bool ceph_msg_data_bio_advance(struct ceph_msg_data_cursor *cursor,
>                                         size_t bytes)
>  {
>         struct ceph_bio_iter *it = &cursor->bio_iter;
> +       struct page *page = bio_iter_page(it->bio, it->iter);
>
>         BUG_ON(bytes > cursor->resid);
>         BUG_ON(bytes > bio_iter_len(it->bio, it->iter));
> @@ -851,7 +852,8 @@ static bool ceph_msg_data_bio_advance(struct ceph_msg_data_cursor *cursor,
>                 return false;   /* no more data */
>         }
>
> -       if (!bytes || (it->iter.bi_size && it->iter.bi_bvec_done))
> +       if (!bytes || (it->iter.bi_size && it->iter.bi_bvec_done &&
> +                      page == bio_iter_page(it->bio, it->iter)))
>                 return false;   /* more bytes to process in this segment */
>
>         if (!it->iter.bi_size) {
> @@ -899,6 +901,7 @@ static bool ceph_msg_data_bvecs_advance(struct ceph_msg_data_cursor *cursor,
>                                         size_t bytes)
>  {
>         struct bio_vec *bvecs = cursor->data->bvec_pos.bvecs;
> +       struct page *page = bvec_iter_page(bvecs, cursor->bvec_iter);
>
>         BUG_ON(bytes > cursor->resid);
>         BUG_ON(bytes > bvec_iter_len(bvecs, cursor->bvec_iter));
> @@ -910,7 +913,8 @@ static bool ceph_msg_data_bvecs_advance(struct ceph_msg_data_cursor *cursor,
>                 return false;   /* no more data */
>         }
>
> -       if (!bytes || cursor->bvec_iter.bi_bvec_done)
> +       if (!bytes || (cursor->bvec_iter.bi_bvec_done &&
> +                      page == bvec_iter_page(bvecs, cursor->bvec_iter)))
>                 return false;   /* more bytes to process in this segment */
>
>         BUG_ON(cursor->last_piece);

Same here, shouldn't be needed.

Thanks,

                Ilya

Re: [PATCH AUTOSEL 5.0 29/98] KVM: arm/arm64: Enforce PTE mappings at stage2 when needed

[Suzuki K Poulose]

Hi Sasha,

On 04/22/2019 08:40 PM, Sasha Levin wrote:
> From: Suzuki K Poulose <suzuki.poulose@arm.com>
> 
> [ Upstream commit a80868f398554842b14d07060012c06efb57c456 ]
> 
> commit 6794ad5443a2118 ("KVM: arm/arm64: Fix unintended stage 2 PMD mappings")
> made the checks to skip huge mappings, stricter. However it introduced
> a bug where we still use huge mappings, ignoring the flag to
> use PTE mappings, by not reseting the vma_pagesize to PAGE_SIZE.
> 
> Also, the checks do not cover the PUD huge pages, that was
> under review during the same period. This patch fixes both
> the issues.
> 
> Fixes : 6794ad5443a2118 ("KVM: arm/arm64: Fix unintended stage 2 PMD mappings")
> Reported-by: Zenghui Yu <yuzenghui@huawei.com>
> Cc: Zenghui Yu <yuzenghui@huawei.com>
> Cc: Christoffer Dall <christoffer.dall@arm.com>
> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
> Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>

Please be aware that we need a follow up fix for this patch to fix the
problem for THP backed memory.

http://lists.infradead.org/pipermail/linux-arm-kernel/2019-April/645324.html


It should appear upstream soon.


Cheers
Suzuki

Re: [PATCH AUTOSEL 5.0 29/98] KVM: arm/arm64: Enforce PTE mappings at stage2 when needed

[Sasha Levin]

On Tue, Apr 23, 2019 at 10:27:26AM +0100, Suzuki K Poulose wrote:
>Hi Sasha,
>
>On 04/22/2019 08:40 PM, Sasha Levin wrote:
>>From: Suzuki K Poulose <suzuki.poulose@arm.com>
>>
>>[ Upstream commit a80868f398554842b14d07060012c06efb57c456 ]
>>
>>commit 6794ad5443a2118 ("KVM: arm/arm64: Fix unintended stage 2 PMD mappings")
>>made the checks to skip huge mappings, stricter. However it introduced
>>a bug where we still use huge mappings, ignoring the flag to
>>use PTE mappings, by not reseting the vma_pagesize to PAGE_SIZE.
>>
>>Also, the checks do not cover the PUD huge pages, that was
>>under review during the same period. This patch fixes both
>>the issues.
>>
>>Fixes : 6794ad5443a2118 ("KVM: arm/arm64: Fix unintended stage 2 PMD mappings")
>>Reported-by: Zenghui Yu <yuzenghui@huawei.com>
>>Cc: Zenghui Yu <yuzenghui@huawei.com>
>>Cc: Christoffer Dall <christoffer.dall@arm.com>
>>Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
>>Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
>>Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
>
>Please be aware that we need a follow up fix for this patch to fix the
>problem for THP backed memory.
>
>http://lists.infradead.org/pipermail/linux-arm-kernel/2019-April/645324.html
>
>
>It should appear upstream soon.

Since it's not upstream yet, I'll drop this patch for now and queue it
for a later release.

--
Thanks,
Sasha

Re: [PATCH AUTOSEL 5.0 61/98] libceph: fix breakage caused by multipage bvecs

[Sasha Levin]

On Tue, Apr 23, 2019 at 10:28:56AM +0200, Ilya Dryomov wrote:
>On Mon, Apr 22, 2019 at 9:44 PM Sasha Levin <sashal@kernel.org> wrote:
>>
>> From: Ilya Dryomov <idryomov@gmail.com>
>>
>> [ Upstream commit 187df76325af5d9e12ae9daec1510307797e54f0 ]
>>
>> A bvec can now consist of multiple physically contiguous pages.
>> This means that bvec_iter_advance() can move to a different page while
>> staying in the same bvec (i.e. ->bi_bvec_done != 0).
>>
>> The messenger works in terms of segments which can now be defined as
>> the smaller of a bvec and a page.  The "more bytes to process in this
>> segment" condition holds only if bvec_iter_advance() leaves us in the
>> same bvec _and_ in the same page.  On next bvec (possibly in the same
>> page) and on next page (possibly in the same bvec) we may need to set
>> ->last_piece.
>>
>> Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
>> Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
>> ---
>>  net/ceph/messenger.c | 8 ++++++--
>>  1 file changed, 6 insertions(+), 2 deletions(-)
>>
>> diff --git a/net/ceph/messenger.c b/net/ceph/messenger.c
>> index 7e71b0df1fbc..3083988ce729 100644
>> --- a/net/ceph/messenger.c
>> +++ b/net/ceph/messenger.c
>> @@ -840,6 +840,7 @@ static bool ceph_msg_data_bio_advance(struct ceph_msg_data_cursor *cursor,
>>                                         size_t bytes)
>>  {
>>         struct ceph_bio_iter *it = &cursor->bio_iter;
>> +       struct page *page = bio_iter_page(it->bio, it->iter);
>>
>>         BUG_ON(bytes > cursor->resid);
>>         BUG_ON(bytes > bio_iter_len(it->bio, it->iter));
>> @@ -851,7 +852,8 @@ static bool ceph_msg_data_bio_advance(struct ceph_msg_data_cursor *cursor,
>>                 return false;   /* no more data */
>>         }
>>
>> -       if (!bytes || (it->iter.bi_size && it->iter.bi_bvec_done))
>> +       if (!bytes || (it->iter.bi_size && it->iter.bi_bvec_done &&
>> +                      page == bio_iter_page(it->bio, it->iter)))
>>                 return false;   /* more bytes to process in this segment */
>>
>>         if (!it->iter.bi_size) {
>> @@ -899,6 +901,7 @@ static bool ceph_msg_data_bvecs_advance(struct ceph_msg_data_cursor *cursor,
>>                                         size_t bytes)
>>  {
>>         struct bio_vec *bvecs = cursor->data->bvec_pos.bvecs;
>> +       struct page *page = bvec_iter_page(bvecs, cursor->bvec_iter);
>>
>>         BUG_ON(bytes > cursor->resid);
>>         BUG_ON(bytes > bvec_iter_len(bvecs, cursor->bvec_iter));
>> @@ -910,7 +913,8 @@ static bool ceph_msg_data_bvecs_advance(struct ceph_msg_data_cursor *cursor,
>>                 return false;   /* no more data */
>>         }
>>
>> -       if (!bytes || cursor->bvec_iter.bi_bvec_done)
>> +       if (!bytes || (cursor->bvec_iter.bi_bvec_done &&
>> +                      page == bvec_iter_page(bvecs, cursor->bvec_iter)))
>>                 return false;   /* more bytes to process in this segment */
>>
>>         BUG_ON(cursor->last_piece);
>
>Same here, shouldn't be needed.

Dropped, thanks!

--
Thanks,
Sasha

Re: [PATCH AUTOSEL 5.0 70/98] tty: fix NULL pointer issue when tty_port ops is not set

[Sasha Levin]

On Mon, Apr 22, 2019 at 10:40:02PM +0200, Greg Kroah-Hartman wrote:
>On Mon, Apr 22, 2019 at 03:41:37PM -0400, Sasha Levin wrote:
>> From: Fabien Dessenne <fabien.dessenne@st.com>
>>
>> [ Upstream commit f4e68d58cf2b20a581759bbc7228052534652673 ]
>>
>> Unlike 'client_ops' which is initialized to 'default_client_ops', the
>> port operations 'ops' may be left to NULL.
>> Check the 'ops' value before checking the 'ops->x' value.
>>
>> Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
>> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
>> Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
>> ---
>>  drivers/tty/tty_port.c | 10 +++++-----
>>  1 file changed, 5 insertions(+), 5 deletions(-)
>
>Nope, I have a revert for this in my tree for 5.2-rc1, no need for this
>in any stable tree, it doesn't do anything :)
>
>Please drop it from all branches, thanks.

Dropped from my queue, thanks!

--
Thanks,
Sasha