linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Dan Murphy <dmurphy@ti.com>
To: <jacek.anaszewski@gmail.com>, <pavel@ucw.cz>,
	<broonie@kernel.org>, <lgirdwood@gmail.com>
Cc: <lee.jones@linaro.org>, <linux-leds@vger.kernel.org>,
	<linux-kernel@vger.kernel.org>, Dan Murphy <dmurphy@ti.com>
Subject: [RESEND PATCH v4 4/6] regulator: lm363x: Add support for LM36274
Date: Wed, 22 May 2019 14:27:31 -0500	[thread overview]
Message-ID: <20190522192733.13422-5-dmurphy@ti.com> (raw)
In-Reply-To: <20190522192733.13422-1-dmurphy@ti.com>

Adding regulator support for the LM36274 backlight driver.
This device can leverage this existing code as the functionality
and registers are common enough between the LM36274 and the LM363x
series of devices.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
---
 drivers/regulator/Kconfig            |  2 +-
 drivers/regulator/lm363x-regulator.c | 52 ++++++++++++++++++++++++++++
 2 files changed, 53 insertions(+), 1 deletion(-)

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index b7f249ee5e68..23252ae81fdf 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -362,7 +362,7 @@ config REGULATOR_LM363X
 	tristate "TI LM363X voltage regulators"
 	depends on MFD_TI_LMU
 	help
-	  This driver supports LM3631 and LM3632 voltage regulators for
+	  This driver supports LM3631, LM3632 and LM36274 voltage regulators for
 	  the LCD bias.
 	  One boost output voltage is configurable and always on.
 	  Other LDOs are used for the display module.
diff --git a/drivers/regulator/lm363x-regulator.c b/drivers/regulator/lm363x-regulator.c
index 382b1cecdd93..1944677b1448 100644
--- a/drivers/regulator/lm363x-regulator.c
+++ b/drivers/regulator/lm363x-regulator.c
@@ -37,6 +37,11 @@
 #define LM3632_VBOOST_MIN		4500000
 #define LM3632_VLDO_MIN			4000000
 
+/* LM36274 */
+#define LM36274_BOOST_VSEL_MAX		0x3f
+#define LM36274_LDO_VSEL_MAX		0x34
+#define LM36274_VOLTAGE_MIN		4000000
+
 /* Common */
 #define LM363X_STEP_50mV		50000
 #define LM363X_STEP_500mV		500000
@@ -217,6 +222,51 @@ static const struct regulator_desc lm363x_regulator_desc[] = {
 		.enable_reg     = LM3632_REG_BIAS_CONFIG,
 		.enable_mask    = LM3632_EN_VNEG_MASK,
 	},
+
+	/* LM36274 */
+	{
+		.name           = "vboost",
+		.of_match	= "vboost",
+		.id             = LM36274_BOOST,
+		.ops            = &lm363x_boost_voltage_table_ops,
+		.n_voltages     = LM36274_BOOST_VSEL_MAX,
+		.min_uV         = LM36274_VOLTAGE_MIN,
+		.uV_step        = LM363X_STEP_50mV,
+		.type           = REGULATOR_VOLTAGE,
+		.owner          = THIS_MODULE,
+		.vsel_reg       = LM36274_REG_VOUT_BOOST,
+		.vsel_mask      = LM36274_VOUT_MASK,
+	},
+	{
+		.name           = "ldo_vpos",
+		.of_match	= "vpos",
+		.id             = LM36274_LDO_POS,
+		.ops            = &lm363x_regulator_voltage_table_ops,
+		.n_voltages     = LM36274_LDO_VSEL_MAX,
+		.min_uV         = LM36274_VOLTAGE_MIN,
+		.uV_step        = LM363X_STEP_50mV,
+		.type           = REGULATOR_VOLTAGE,
+		.owner          = THIS_MODULE,
+		.vsel_reg       = LM36274_REG_VOUT_POS,
+		.vsel_mask      = LM36274_VOUT_MASK,
+		.enable_reg     = LM36274_REG_BIAS_CONFIG_1,
+		.enable_mask    = LM36274_EN_VPOS_MASK,
+	},
+	{
+		.name           = "ldo_vneg",
+		.of_match	= "vneg",
+		.id             = LM36274_LDO_NEG,
+		.ops            = &lm363x_regulator_voltage_table_ops,
+		.n_voltages     = LM36274_LDO_VSEL_MAX,
+		.min_uV         = LM36274_VOLTAGE_MIN,
+		.uV_step        = LM363X_STEP_50mV,
+		.type           = REGULATOR_VOLTAGE,
+		.owner          = THIS_MODULE,
+		.vsel_reg       = LM36274_REG_VOUT_NEG,
+		.vsel_mask      = LM36274_VOUT_MASK,
+		.enable_reg     = LM36274_REG_BIAS_CONFIG_1,
+		.enable_mask    = LM36274_EN_VNEG_MASK,
+	},
 };
 
 static struct gpio_desc *lm363x_regulator_of_get_enable_gpio(struct device *dev, int id)
@@ -229,9 +279,11 @@ static struct gpio_desc *lm363x_regulator_of_get_enable_gpio(struct device *dev,
 	 */
 	switch (id) {
 	case LM3632_LDO_POS:
+	case LM36274_LDO_POS:
 		return gpiod_get_index_optional(dev, "enable", 0,
 				GPIOD_OUT_LOW | GPIOD_FLAGS_BIT_NONEXCLUSIVE);
 	case LM3632_LDO_NEG:
+	case LM36274_LDO_NEG:
 		return gpiod_get_index_optional(dev, "enable", 1,
 				GPIOD_OUT_LOW | GPIOD_FLAGS_BIT_NONEXCLUSIVE);
 	default:
-- 
2.21.0.5.gaeb582a983


  parent reply	other threads:[~2019-05-22 19:44 UTC|newest]

Thread overview: 37+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-05-22 19:27 [PATCH v4 0/6] LM36274 Introduction Dan Murphy
2019-05-22 19:27 ` [RESEND PATCH v4 1/6] regulator: lm363x: Make the gpio register enable flexible Dan Murphy
2019-05-22 21:22   ` Pavel Machek
2019-05-23 13:03   ` Mark Brown
2019-05-23 13:50     ` Dan Murphy
2019-05-26 12:48       ` Mark Brown
2019-05-29 11:51         ` Dan Murphy
2019-05-29 15:10           ` Mark Brown
2019-05-29 20:47             ` Dan Murphy
2019-05-30 15:26               ` Mark Brown
2019-06-04 15:14                 ` Dan Murphy
2019-06-04 15:33                   ` Mark Brown
2019-05-22 19:27 ` [RESEND PATCH v4 2/6] dt-bindings: mfd: Add lm36274 bindings to ti-lmu Dan Murphy
2019-05-22 21:22   ` Pavel Machek
2019-05-22 19:27 ` [RESEND PATCH v4 3/6] mfd: ti-lmu: Add LM36274 support to the ti-lmu Dan Murphy
2019-05-23  8:09   ` Pavel Machek
2019-05-22 19:27 ` Dan Murphy [this message]
2019-05-23  8:12   ` [RESEND PATCH v4 4/6] regulator: lm363x: Add support for LM36274 Pavel Machek
2019-05-23 13:04   ` Mark Brown
2019-05-22 19:27 ` [RESEND PATCH v4 5/6] dt-bindings: leds: Add LED bindings for the LM36274 Dan Murphy
2019-05-23 12:43   ` Pavel Machek
2019-05-22 19:27 ` [RESEND PATCH v4 6/6] leds: lm36274: Introduce the TI LM36274 LED driver Dan Murphy
2019-05-23 12:50   ` Pavel Machek
2019-05-23 19:09     ` Dan Murphy
2019-05-24 20:51       ` Jacek Anaszewski
2019-05-29 13:58         ` Lee Jones
2019-05-29 20:50           ` Jacek Anaszewski
2019-05-30  7:38             ` Lee Jones
2019-05-30 19:58               ` Jacek Anaszewski
2019-05-31  6:23                 ` Lee Jones
2019-05-31 19:44                   ` Jacek Anaszewski
2019-05-31 21:07                     ` Dan Murphy
2019-05-31 21:57                       ` Jacek Anaszewski
2019-05-31 22:41                         ` Dan Murphy
2019-06-01 13:55                           ` Jacek Anaszewski
2019-05-22 19:37 ` [PATCH v4 0/6] LM36274 Introduction Jacek Anaszewski
2019-05-22 19:39   ` Dan Murphy

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190522192733.13422-5-dmurphy@ti.com \
    --to=dmurphy@ti.com \
    --cc=broonie@kernel.org \
    --cc=jacek.anaszewski@gmail.com \
    --cc=lee.jones@linaro.org \
    --cc=lgirdwood@gmail.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-leds@vger.kernel.org \
    --cc=pavel@ucw.cz \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).