From: Jordan Crouse <jcrouse@codeaurora.org>
To: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Cc: robdclark@gmail.com, sean@poorly.run, airlied@linux.ie,
daniel@ffwll.ch, marc.w.gonzalez@free.fr,
bjorn.andersson@linaro.org, linux-arm-msm@vger.kernel.org,
dri-devel@lists.freedesktop.org, freedreno@lists.freedesktop.org,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH] drm/msm/adreno: Add A540 support
Date: Tue, 28 May 2019 14:45:05 -0600 [thread overview]
Message-ID: <20190528204505.GC23227@jcrouse1-lnx.qualcomm.com> (raw)
In-Reply-To: <20190528170612.39003-1-jeffrey.l.hugo@gmail.com>
On Tue, May 28, 2019 at 10:06:12AM -0700, Jeffrey Hugo wrote:
> The A540 is a derivative of the A530, and is found in the MSM8998 SoC.
>
> Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
> ---
> drivers/gpu/drm/msm/adreno/a5xx_gpu.c | 22 +++++++
> drivers/gpu/drm/msm/adreno/a5xx_power.c | 76 +++++++++++++++++++++-
> drivers/gpu/drm/msm/adreno/adreno_device.c | 18 +++++
> drivers/gpu/drm/msm/adreno/adreno_gpu.h | 6 ++
> 4 files changed, 119 insertions(+), 3 deletions(-)
This is awesome. I'm glad we can finally check this off the list.
> diff --git a/drivers/gpu/drm/msm/adreno/a5xx_gpu.c b/drivers/gpu/drm/msm/adreno/a5xx_gpu.c
> index e5fcefa49f19..7ca8fde22fd8 100644
> --- a/drivers/gpu/drm/msm/adreno/a5xx_gpu.c
> +++ b/drivers/gpu/drm/msm/adreno/a5xx_gpu.c
> @@ -318,12 +318,19 @@ static const struct {
>
> void a5xx_set_hwcg(struct msm_gpu *gpu, bool state)
> {
> + struct adreno_gpu *adreno_gpu = to_adreno_gpu(gpu);
> unsigned int i;
>
> for (i = 0; i < ARRAY_SIZE(a5xx_hwcg); i++)
> gpu_write(gpu, a5xx_hwcg[i].offset,
> state ? a5xx_hwcg[i].value : 0);
>
> + if (adreno_is_a540(adreno_gpu)) {
> + gpu_write(gpu, REG_A5XX_RBBM_CLOCK_HYST_GPMU, 0x00000222);
I don't think this one is needed - we can just go with the one two lines below.
> + gpu_write(gpu, REG_A5XX_RBBM_CLOCK_DELAY_GPMU, 0x00000770);
> + gpu_write(gpu, REG_A5XX_RBBM_CLOCK_HYST_GPMU, 0x00000004);
Both of these need the state ? <value> : 0x0 hack to turn off HWCG if requested
> + }
> +
> gpu_write(gpu, REG_A5XX_RBBM_CLOCK_CNTL, state ? 0xAAA8AA00 : 0);
> gpu_write(gpu, REG_A5XX_RBBM_ISDB_CNT, state ? 0x182 : 0x180);
> }
> @@ -507,6 +514,9 @@ static int a5xx_hw_init(struct msm_gpu *gpu)
>
> gpu_write(gpu, REG_A5XX_VBIF_ROUND_ROBIN_QOS_ARB, 0x00000003);
>
> + if (adreno_is_a540(adreno_gpu))
> + gpu_write(gpu, REG_A5XX_VBIF_GATE_OFF_WRREQ_EN, 0x00000009);
> +
> /* Make all blocks contribute to the GPU BUSY perf counter */
> gpu_write(gpu, REG_A5XX_RBBM_PERFCTR_GPU_BUSY_MASKED, 0xFFFFFFFF);
>
> @@ -592,6 +602,8 @@ static int a5xx_hw_init(struct msm_gpu *gpu)
> /* Set the highest bank bit */
> gpu_write(gpu, REG_A5XX_TPL1_MODE_CNTL, 2 << 7);
> gpu_write(gpu, REG_A5XX_RB_MODE_CNTL, 2 << 1);
> + if (adreno_is_a540(adreno_gpu))
> + gpu_write(gpu, REG_A5XX_UCHE_DBG_ECO_CNTL_2, 2);
>
> /* Protect registers from the CP */
> gpu_write(gpu, REG_A5XX_CP_PROTECT_CNTL, 0x00000007);
> @@ -642,6 +654,16 @@ static int a5xx_hw_init(struct msm_gpu *gpu)
> REG_A5XX_RBBM_SECVID_TSB_TRUSTED_BASE_HI, 0x00000000);
> gpu_write(gpu, REG_A5XX_RBBM_SECVID_TSB_TRUSTED_SIZE, 0x00000000);
>
> + /*
> + * VPC corner case with local memory load kill leads to corrupt
> + * internal state. Normal Disable does not work for all a5x chips.
> + * So do the following setting to disable it.
> + */
> + if (adreno_gpu->info->quirks & ADRENO_QUIRK_LMLOADKILL_DISABLE) {
This is a5xx only quirk but it applies to multiple 5xx targets so I think its
reasonable to identify it as a quirk and use it as such to make it easier on
future code porters.
> + gpu_rmw(gpu, REG_A5XX_VPC_DBG_ECO_CNTL, 0, BIT(23));
> + gpu_rmw(gpu, 0xE04, BIT(18), 0); /*REG_A5XX_HLSQ_DBG_ECO_CNTL*/
You should define and use REG_A5XX_HLSQ_DBG_ECO_CNTL symbolically. We can help
you do the envytools dance if you need.
> + }
> +
> ret = adreno_hw_init(gpu);
> if (ret)
> return ret;
> diff --git a/drivers/gpu/drm/msm/adreno/a5xx_power.c b/drivers/gpu/drm/msm/adreno/a5xx_power.c
> index 70e65c94e525..5cb325c6eb8f 100644
> --- a/drivers/gpu/drm/msm/adreno/a5xx_power.c
> +++ b/drivers/gpu/drm/msm/adreno/a5xx_power.c
> @@ -32,6 +32,18 @@
> #define AGC_POWER_CONFIG_PRODUCTION_ID 1
> #define AGC_INIT_MSG_VALUE 0xBABEFACE
>
> +/* AGC_LM_CONFIG (A540+) */
> +#define AGC_LM_CONFIG (136/4)
> +#define AGC_LM_CONFIG_GPU_VERSION_SHIFT 17
> +#define AGC_LM_CONFIG_ENABLE_GPMU_ADAPTIVE 1
> +#define AGC_LM_CONFIG_THROTTLE_DISABLE (2 << 8)
> +#define AGC_LM_CONFIG_ISENSE_ENABLE (1 << 4)
> +#define AGC_LM_CONFIG_ENABLE_ERROR (3 << 4)
> +#define AGC_LM_CONFIG_LLM_ENABLED (1 << 16)
> +#define AGC_LM_CONFIG_BCL_DISABLED (1 << 24)
> +
> +#define AGC_LEVEL_CONFIG (140/4)
> +
> static struct {
> uint32_t reg;
> uint32_t value;
> @@ -116,7 +128,7 @@ static inline uint32_t _get_mvolts(struct msm_gpu *gpu, uint32_t freq)
> }
>
> /* Setup thermal limit management */
> -static void a5xx_lm_setup(struct msm_gpu *gpu)
> +static void a530_lm_setup(struct msm_gpu *gpu)
> {
> struct adreno_gpu *adreno_gpu = to_adreno_gpu(gpu);
> struct a5xx_gpu *a5xx_gpu = to_a5xx_gpu(adreno_gpu);
> @@ -165,6 +177,45 @@ static void a5xx_lm_setup(struct msm_gpu *gpu)
> gpu_write(gpu, AGC_INIT_MSG_MAGIC, AGC_INIT_MSG_VALUE);
> }
>
> +#define PAYLOAD_SIZE(_size) ((_size) * sizeof(u32))
> +#define LM_DCVS_LIMIT 1
> +#define LEVEL_CONFIG ~(0x303)
> +
> +static void a540_lm_setup(struct msm_gpu *gpu)
> +{
> + struct adreno_gpu *adreno_gpu = to_adreno_gpu(gpu);
> + u32 config;
> +
> + /* The battery current limiter isn't enabled for A540 */
> + config = AGC_LM_CONFIG_BCL_DISABLED;
> + config |= adreno_gpu->rev.patchid << AGC_LM_CONFIG_GPU_VERSION_SHIFT;
> +
> + /* For now disable GPMU side throttling */
> + config |= AGC_LM_CONFIG_THROTTLE_DISABLE;
> +
> + /* Until we get clock scaling 0 is always the active power level */
> + gpu_write(gpu, REG_A5XX_GPMU_GPMU_VOLTAGE, 0x80000000 | 0);
> +
> + /* Fixed at 6000 for now */
> + gpu_write(gpu, REG_A5XX_GPMU_GPMU_PWR_THRESHOLD, 0x80000000 | 6000);
> +
> + gpu_write(gpu, AGC_MSG_STATE, 0x80000001);
> + gpu_write(gpu, AGC_MSG_COMMAND, AGC_POWER_CONFIG_PRODUCTION_ID);
> +
> + gpu_write(gpu, AGC_MSG_PAYLOAD(0), 5448); //magic number?
They are all magic numbers but especially this number. 530 has the same.
<snip>
Jordan
--
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
next prev parent reply other threads:[~2019-05-28 20:45 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-05-28 17:06 [PATCH] drm/msm/adreno: Add A540 support Jeffrey Hugo
2019-05-28 20:45 ` Jordan Crouse [this message]
2019-05-28 21:21 ` Jeffrey Hugo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190528204505.GC23227@jcrouse1-lnx.qualcomm.com \
--to=jcrouse@codeaurora.org \
--cc=airlied@linux.ie \
--cc=bjorn.andersson@linaro.org \
--cc=daniel@ffwll.ch \
--cc=dri-devel@lists.freedesktop.org \
--cc=freedreno@lists.freedesktop.org \
--cc=jeffrey.l.hugo@gmail.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=marc.w.gonzalez@free.fr \
--cc=robdclark@gmail.com \
--cc=sean@poorly.run \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).