From: "Uwe Kleine-König" <u.kleine-koenig@pengutronix.de>
To: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>,
Ludovic Desroches <ludovic.desroches@microchip.com>,
linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org, info@acmesystems.it
Subject: Re: [PATCH v3 6/7] ARM: dts: at91: at91sam9x5: switch to new clock bindings
Date: Sat, 27 Jul 2019 17:39:43 +0200 [thread overview]
Message-ID: <20190727153943.abjyfhkdnafq2u5w@pengutronix.de> (raw)
In-Reply-To: <20181112133108.31021-7-alexandre.belloni@bootlin.com>
Hello Alexandre,
On Mon, Nov 12, 2018 at 02:31:07PM +0100, Alexandre Belloni wrote:
> Switch at91sam9x5 boards to the new PMC clock bindings.
This patch results in a broken dtb for my AriettaG25[1]. It compiles
fine, but booting results in:
SD/MMC: dt blob: Read file acme-arietta.dtb to 0x21000000
SD: Card Capacity: Standard
SD: Specification Version 3.0X
Booting zImage ......
zImage magic: 0x16f2818 is found
Using device tree in place at 0x21000000
Starting linux kernel ..., machid: 0xffffffff
Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Linux version 5.3.0-rc1+ (uwe@taurus) (gcc version 7.3.1 20180201 (OSELAS.Toolchain-2018.02.0 7-20180201)) #4 Sat Jul 27 15:47:15 CEST 2019
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=0005317f
CPU: VIVT data cache, VIVT instruction cache
OF: fdt: Machine model: Acme Systems Arietta G25
printk: bootconsole [earlycon0] enabled
printk: debug: ignoring loglevel setting.
Memory policy: Data cache writeback
On node 0 totalpages: 32768
Normal zone: 256 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 32768 pages, LIFO batch:7
pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
pcpu-alloc: [0] 0
Built 1 zonelists, mobility grouping on. Total pages: 32512
Kernel command line: earlyprintk ignore_loglevel mem=128M console=ttyS0,115200 root=/dev/mmcblk0p2 rootfstype=ext4 rw rootwait
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
mem auto-init: stack:off, heap alloc:off, heap free:off
Memory: 121352K/131072K available (5826K kernel code, 199K rwdata, 1892K rodata, 232K init, 125K bss, 9720K reserved, 0K cma-reserved)
NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
random: get_random_bytes called from start_kernel+0x294/0x474 with crng_init=0
bad: scheduling from the idle thread!
CPU: 0 PID: 0 Comm: swapper Not tainted 5.3.0-rc1+ #4
Hardware name: Atmel AT91SAM9
[<c000fc4c>] (unwind_backtrace) from [<c000d654>] (show_stack+0x10/0x18)
[<c000d654>] (show_stack) from [<c059db74>] (dump_stack+0x18/0x24)
[<c059db74>] (dump_stack) from [<c00386e8>] (dequeue_task_idle+0x1c/0x34)
[<c00386e8>] (dequeue_task_idle) from [<c05b5818>] (__schedule+0x250/0x38c)
[<c05b5818>] (__schedule) from [<c05b59e8>] (schedule+0x94/0xc8)
[<c05b59e8>] (schedule) from [<c05b876c>] (schedule_hrtimeout_range_clock+0xf4/0x13c)
[<c05b876c>] (schedule_hrtimeout_range_clock) from [<c05b87cc>] (schedule_hrtimeout_range+0x18/0x24)
[<c05b87cc>] (schedule_hrtimeout_range) from [<c05b8240>] (usleep_range+0x70/0x98)
[<c05b8240>] (usleep_range) from [<c02a18a0>] (clk_slow_rc_osc_prepare+0x28/0x34)
[<c02a18a0>] (clk_slow_rc_osc_prepare) from [<c029af78>] (clk_core_prepare+0x84/0xa0)
[<c029af78>] (clk_core_prepare) from [<c029af54>] (clk_core_prepare+0x60/0xa0)
[<c029af54>] (clk_core_prepare) from [<c029b790>] (clk_prepare+0x1c/0x30)
[<c029b790>] (clk_prepare) from [<c02f1310>] (regmap_mmio_attach_clk+0x1c/0x24)
[<c02f1310>] (regmap_mmio_attach_clk) from [<c02f7a98>] (of_syscon_register+0x218/0x268)
[<c02f7a98>] (of_syscon_register) from [<c02f7b18>] (syscon_node_to_regmap+0x30/0x58)
[<c02f7b18>] (syscon_node_to_regmap) from [<c07d2f7c>] (at91sam9x5_pmc_setup+0x78/0x430)
[<c07d2f7c>] (at91sam9x5_pmc_setup) from [<c07cfe88>] (of_clk_init+0x188/0x21c)
[<c07cfe88>] (of_clk_init) from [<c07c062c>] (time_init+0x1c/0x2c)
[<c07c062c>] (time_init) from [<c07bcbec>] (start_kernel+0x2c4/0x474)
[<c07bcbec>] (start_kernel) from [<00000000>] (0x0)
bad: scheduling from the idle thread!
CPU: 0 PID: 0 Comm: swapper Not tainted 5.3.0-rc1+ #4
Hardware name: Atmel AT91SAM9
[<c000fc4c>] (unwind_backtrace) from [<c000d654>] (show_stack+0x10/0x18)
[<c000d654>] (show_stack) from [<c059db74>] (dump_stack+0x18/0x24)
[<c059db74>] (dump_stack) from [<c00386e8>] (dequeue_task_idle+0x1c/0x34)
[<c00386e8>] (dequeue_task_idle) from [<c05b5818>] (__schedule+0x250/0x38c)
[<c05b5818>] (__schedule) from [<c05b59e8>] (schedule+0x94/0xc8)
[<c05b59e8>] (schedule) from [<c05b876c>] (schedule_hrtimeout_range_clock+0xf4/0x13c)
[<c05b876c>] (schedule_hrtimeout_range_clock) from [<c05b87cc>] (schedule_hrtimeout_range+0x18/0x24)
[<c05b87cc>] (schedule_hrtimeout_range) from [<c05b8240>] (usleep_range+0x70/0x98)
[<c05b8240>] (usleep_range) from [<c02a18a0>] (clk_slow_rc_osc_prepare+0x28/0x34)
[<c02a18a0>] (clk_slow_rc_osc_prepare) from [<c029af78>] (clk_core_prepare+0x84/0xa0)
[<c029af78>] (clk_core_prepare) from [<c029af54>] (clk_core_prepare+0x60/0xa0)
[<c029af54>] (clk_core_prepare) from [<c029b790>] (clk_prepare+0x1c/0x30)
[<c029b790>] (clk_prepare) from [<c02f1310>] (regmap_mmio_attach_clk+0x1c/0x24)
[<c02f1310>] (regmap_mmio_attach_clk) from [<c02f7a98>] (of_syscon_register+0x218/0x268)
[<c02f7a98>] (of_syscon_register) from [<c02f7b18>] (syscon_node_to_regmap+0x30/0x58)
[<c02f7b18>] (syscon_node_to_regmap) from [<c07d2f7c>] (at91sam9x5_pmc_setup+0x78/0x430)
[<c07d2f7c>] (at91sam9x5_pmc_setup) from [<c07cfe88>] (of_clk_init+0x188/0x21c)
[<c07cfe88>] (of_clk_init) from [<c07c062c>] (time_init+0x1c/0x2c)
[<c07c062c>] (time_init) from [<c07bcbec>] (start_kernel+0x2c4/0x474)
[<c07bcbec>] (start_kernel) from [<00000000>] (0x0)
bad: scheduling from the idle thread!
CPU: 0 PID: 0 Comm: swapper Not tainted 5.3.0-rc1+ #4
Hardware name: Atmel AT91SAM9
...
The error message repeats without end. (I obviously didn't test until
the end :-), but after 10 minutes the machine still prints this message.)
With the old dtb Linux 5.3-rc1 boots just fine. I assume this is not
related to my dts or .config so I'm not attaching these here. If you're
interested I can provide them of course.
Best regards
Uwe
[1] https://www.acmesystems.it/arietta
--
Pengutronix e.K. | Uwe Kleine-König |
Industrial Linux Solutions | http://www.pengutronix.de/ |
next prev parent reply other threads:[~2019-07-27 15:39 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-11-12 13:31 [PATCH v3 0/7] clk: at91: Rework DT bindings Alexandre Belloni
2018-11-12 13:31 ` [PATCH v3 1/7] ARM: dts: at91: sama5d4: switch to new clock bindings Alexandre Belloni
2018-11-12 13:31 ` [PATCH v3 2/7] ARM: dts: at91: sama5d2: switch to new binding Alexandre Belloni
2018-11-13 8:27 ` Ludovic Desroches
2018-11-13 9:03 ` Alexandre Belloni
2018-11-12 13:31 ` [PATCH v3 3/7] ARM: dts: at91: at91sam9260: switch to new clock bindings Alexandre Belloni
2018-11-12 13:31 ` [PATCH v3 4/7] ARM: dts: at91: at91sam9261: " Alexandre Belloni
2018-11-12 13:31 ` [PATCH v3 5/7] ARM: dts: at91: at91sam9263: " Alexandre Belloni
2018-11-12 13:31 ` [PATCH v3 6/7] ARM: dts: at91: at91sam9x5: " Alexandre Belloni
2019-07-27 15:39 ` Uwe Kleine-König [this message]
2019-07-28 20:56 ` Uwe Kleine-König
2019-08-20 19:40 ` Alexandre Belloni
2018-11-12 13:31 ` [PATCH v3 7/7] ARM: dts: at91: at91sam9rl: " Alexandre Belloni
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190727153943.abjyfhkdnafq2u5w@pengutronix.de \
--to=u.kleine-koenig@pengutronix.de \
--cc=alexandre.belloni@bootlin.com \
--cc=info@acmesystems.it \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=ludovic.desroches@microchip.com \
--cc=nicolas.ferre@microchip.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).