[PATCH v3 2/2] ARM: dts: imx6ul-kontron-n6310: Add Kontron i.MX6UL N6310 SoM and boards

[Krzysztof Kozlowski <krzk@kernel.org>]

Add support for i.MX6UL modules from Kontron Electronics GmbH (before
acquisition: Exceet Electronics) and evalkit boards based on it:

1. N6310 SOM: i.MX6 UL System-on-Module, a 25x25 mm solderable module
   (LGA pads and pin castellations) with 256 MB RAM, 1 MB NOR-Flash,
   256 MB NAND and other interfaces,
2. N6310 S: evalkit, w/wo eMMC, without display,
3. N6310 S 43: evalkit with 4.3" display,
4. N6310 S 50: evalkit with 5.0" display.

This includes device nodes for unsupported displays (Admatec
T043C004800272T2A and T070P133T0S301).

The work is based on Exceet/Kontron source code (GPLv2) with numerous
changes:
1. Reorganize files,
2. Rename Exceet -> Kontron,
3. Rename models/compatibles to match newest Kontron product naming,
4. Fix coding style errors and adjust to device tree coding guidelines,
5. Fix DTC warnings,
6. Extend compatibles so eval boards inherit the SoM compatible,
7. Use defines instead of GPIO and interrupt flag values,
8. Use proper vendor compatible for Macronix SPI NOR,
9. Sort nodes alphabetically.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

---

Changes since v2, after Fabio's review:
1. Add "imx6ul" compatible to board name (that's what I understood from
   review),
2. Add vendor/device prefix to eeprom and document the compatible,
3. Use "admatecde" as vendor compatible to avoid confusion with Admatec
   AG in Switzerland (also making LCD panels),
4. Use generic names for nodes,
5. Use IRQ_TYPE_LEVEL_LOW,
6. Move iomux to the end of files,
7. Remove regulators node (include regulators in top level),
8. Remove cpu clock-frequency,
9. Other minor fixes pointed by Fabio.

Changes since v1, after Frieder's review:
1. Remove unneeded license notes,
2. Add Kontron copyright (2018),
3. Rename the files/models/compatibles to new naming - N6310,
4. Remove unneeded CPU operating points override,
5. Switch regulator nodes into simple children nodes without addresses
   (so not simple bus),
6. Use proper vendor compatible for Macronix SPI NOR.
---
 .../devicetree/bindings/arm/fsl.yaml          |   4 +
 .../devicetree/bindings/eeprom/at25.txt       |   1 +
 arch/arm/boot/dts/Makefile                    |   3 +
 .../boot/dts/imx6ul-kontron-n6310-s-43.dts    | 119 +++++
 .../boot/dts/imx6ul-kontron-n6310-s-50.dts    | 119 +++++
 arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts  | 420 ++++++++++++++++++
 .../boot/dts/imx6ul-kontron-n6310-som.dtsi    | 134 ++++++
 7 files changed, 800 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6ul-kontron-n6310-s-43.dts
 create mode 100644 arch/arm/boot/dts/imx6ul-kontron-n6310-s-50.dts
 create mode 100644 arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts
 create mode 100644 arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 7294ac36f4c0..6a6c09d67dea 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -161,6 +161,10 @@ properties:
         items:
           - enum:
               - fsl,imx6ul-14x14-evk      # i.MX6 UltraLite 14x14 EVK Board
+              - kontron,imx6ul-n6310-som  # Kontron N6310 SOM
+              - kontron,imx6ul-n6310-s    # Kontron N6310 S Board
+              - kontron,imx6ul-n6310-s-43 # Kontron N6310 S 43 Board
+              - kontron,imx6ul-n6310-s-50 # Kontron N6310 S 50 Board
           - const: fsl,imx6ul
 
       - description: i.MX6ULL based Boards
diff --git a/Documentation/devicetree/bindings/eeprom/at25.txt b/Documentation/devicetree/bindings/eeprom/at25.txt
index b3bde97dc199..42577dd113dd 100644
--- a/Documentation/devicetree/bindings/eeprom/at25.txt
+++ b/Documentation/devicetree/bindings/eeprom/at25.txt
@@ -3,6 +3,7 @@ EEPROMs (SPI) compatible with Atmel at25.
 Required properties:
 - compatible : Should be "<vendor>,<type>", and generic value "atmel,at25".
   Example "<vendor>,<type>" values:
+    "anvo,anv32e61w"
     "microchip,25lc040"
     "st,m95m02"
     "st,m95256"
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 9159fa2cea90..28b6cb3454a3 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -569,6 +569,9 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
 	imx6ul-geam.dtb \
 	imx6ul-isiot-emmc.dtb \
 	imx6ul-isiot-nand.dtb \
+	imx6ul-kontron-n6310-s.dtb \
+	imx6ul-kontron-n6310-s-43.dtb \
+	imx6ul-kontron-n6310-s-50.dtb \
 	imx6ul-liteboard.dtb \
 	imx6ul-opos6uldev.dtb \
 	imx6ul-pico-hobbit.dtb \
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6310-s-43.dts b/arch/arm/boot/dts/imx6ul-kontron-n6310-s-43.dts
new file mode 100644
index 000000000000..c83793725245
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-kontron-n6310-s-43.dts
@@ -0,0 +1,119 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#include "imx6ul-kontron-n6310-s.dts"
+
+/ {
+	model = "Kontron N6310 S 43";
+	compatible = "kontron,imx6ul-n6310-s-43", "kontron,imx6ul-n6310-s",
+		     "kontron,imx6ul-n6310-som", "fsl,imx6ul";
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm7 0 5000000>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+		status = "okay";
+	};
+
+	panel {
+		compatible = "admatecde,t043c004800272t2a";
+		backlight = <&backlight>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+};
+
+&i2c4 {
+	touchscreen@5d {
+		compatible = "goodix,gt928";
+		reg = <0x5d>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_cap_touch>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpio5 8 GPIO_ACTIVE_HIGH>;
+		irq-gpios = <&gpio5 6 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lcdif_dat &pinctrl_lcdif_ctrl>;
+	status = "okay";
+
+	port {
+		display_out: endpoint {
+			remote-endpoint = <&panel_in>;
+		};
+	};
+};
+
+&pwm7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm7>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_lcdif_dat: lcdifdatgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA00__LCDIF_DATA00	0x79
+			MX6UL_PAD_LCD_DATA01__LCDIF_DATA01	0x79
+			MX6UL_PAD_LCD_DATA02__LCDIF_DATA02	0x79
+			MX6UL_PAD_LCD_DATA03__LCDIF_DATA03	0x79
+			MX6UL_PAD_LCD_DATA04__LCDIF_DATA04	0x79
+			MX6UL_PAD_LCD_DATA05__LCDIF_DATA05	0x79
+			MX6UL_PAD_LCD_DATA06__LCDIF_DATA06	0x79
+			MX6UL_PAD_LCD_DATA07__LCDIF_DATA07	0x79
+			MX6UL_PAD_LCD_DATA08__LCDIF_DATA08	0x79
+			MX6UL_PAD_LCD_DATA09__LCDIF_DATA09	0x79
+			MX6UL_PAD_LCD_DATA10__LCDIF_DATA10	0x79
+			MX6UL_PAD_LCD_DATA11__LCDIF_DATA11	0x79
+			MX6UL_PAD_LCD_DATA12__LCDIF_DATA12	0x79
+			MX6UL_PAD_LCD_DATA13__LCDIF_DATA13	0x79
+			MX6UL_PAD_LCD_DATA14__LCDIF_DATA14	0x79
+			MX6UL_PAD_LCD_DATA15__LCDIF_DATA15	0x79
+			MX6UL_PAD_LCD_DATA16__LCDIF_DATA16	0x79
+			MX6UL_PAD_LCD_DATA17__LCDIF_DATA17	0x79
+			MX6UL_PAD_LCD_DATA18__LCDIF_DATA18	0x79
+			MX6UL_PAD_LCD_DATA19__LCDIF_DATA19	0x79
+			MX6UL_PAD_LCD_DATA20__LCDIF_DATA20	0x79
+			MX6UL_PAD_LCD_DATA21__LCDIF_DATA21	0x79
+			MX6UL_PAD_LCD_DATA22__LCDIF_DATA22	0x79
+			MX6UL_PAD_LCD_DATA23__LCDIF_DATA23	0x79
+		>;
+	};
+
+	pinctrl_lcdif_ctrl: lcdifctrlgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_CLK__LCDIF_CLK		0x79
+			MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE	0x79
+			MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC	0x79
+			MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC	0x79
+			MX6UL_PAD_LCD_RESET__LCDIF_RESET	0x79
+		>;
+	};
+
+	pinctrl_cap_touch: captouchgrp {
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER6__GPIO5_IO06	0x1b0b0 /* Touch Interrupt */
+			MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07	0x1b0b0 /* Touch Reset */
+			MX6UL_PAD_SNVS_TAMPER8__GPIO5_IO08	0x1b0b0 /* Touch Wake */
+		>;
+	};
+
+	pinctrl_pwm7: pwm7grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_VSYNC__PWM7_OUT		0x110b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6310-s-50.dts b/arch/arm/boot/dts/imx6ul-kontron-n6310-s-50.dts
new file mode 100644
index 000000000000..f9c9afa58771
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-kontron-n6310-s-50.dts
@@ -0,0 +1,119 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#include "imx6ul-kontron-n6310-s.dts"
+
+/ {
+	model = "Kontron N6310 S 50";
+	compatible = "kontron,imx6ul-n6310-s-50", "kontron,imx6ul-n6310-s",
+		     "kontron,imx6ul-n6310-som", "fsl,imx6ul";
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm7 0 5000000>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+		status = "okay";
+	};
+
+	panel {
+		compatible = "admatecde,t070p133t0s301";
+		backlight = <&backlight>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+};
+
+&i2c4 {
+	touchscreen@5d {
+		compatible = "goodix,gt928";
+		reg = <0x5d>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_cap_touch>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpio5 8 GPIO_ACTIVE_HIGH>;
+		irq-gpios = <&gpio5 6 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lcdif_dat &pinctrl_lcdif_ctrl>;
+	status = "okay";
+
+	port {
+		display_out: endpoint {
+			remote-endpoint = <&panel_in>;
+		};
+	};
+};
+
+&pwm7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm7>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_lcdif_dat: lcdifdatgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA00__LCDIF_DATA00	0x79
+			MX6UL_PAD_LCD_DATA01__LCDIF_DATA01	0x79
+			MX6UL_PAD_LCD_DATA02__LCDIF_DATA02	0x79
+			MX6UL_PAD_LCD_DATA03__LCDIF_DATA03	0x79
+			MX6UL_PAD_LCD_DATA04__LCDIF_DATA04	0x79
+			MX6UL_PAD_LCD_DATA05__LCDIF_DATA05	0x79
+			MX6UL_PAD_LCD_DATA06__LCDIF_DATA06	0x79
+			MX6UL_PAD_LCD_DATA07__LCDIF_DATA07	0x79
+			MX6UL_PAD_LCD_DATA08__LCDIF_DATA08	0x79
+			MX6UL_PAD_LCD_DATA09__LCDIF_DATA09	0x79
+			MX6UL_PAD_LCD_DATA10__LCDIF_DATA10	0x79
+			MX6UL_PAD_LCD_DATA11__LCDIF_DATA11	0x79
+			MX6UL_PAD_LCD_DATA12__LCDIF_DATA12	0x79
+			MX6UL_PAD_LCD_DATA13__LCDIF_DATA13	0x79
+			MX6UL_PAD_LCD_DATA14__LCDIF_DATA14	0x79
+			MX6UL_PAD_LCD_DATA15__LCDIF_DATA15	0x79
+			MX6UL_PAD_LCD_DATA16__LCDIF_DATA16	0x79
+			MX6UL_PAD_LCD_DATA17__LCDIF_DATA17	0x79
+			MX6UL_PAD_LCD_DATA18__LCDIF_DATA18	0x79
+			MX6UL_PAD_LCD_DATA19__LCDIF_DATA19	0x79
+			MX6UL_PAD_LCD_DATA20__LCDIF_DATA20	0x79
+			MX6UL_PAD_LCD_DATA21__LCDIF_DATA21	0x79
+			MX6UL_PAD_LCD_DATA22__LCDIF_DATA22	0x79
+			MX6UL_PAD_LCD_DATA23__LCDIF_DATA23	0x79
+		>;
+	};
+
+	pinctrl_lcdif_ctrl: lcdifctrlgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_CLK__LCDIF_CLK		0x79
+			MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE	0x79
+			MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC	0x79
+			MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC	0x79
+			MX6UL_PAD_LCD_RESET__LCDIF_RESET	0x79
+		>;
+	};
+
+	pinctrl_cap_touch: captouchgrp {
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER6__GPIO5_IO06	0x1b0b0 /* Touch Interrupt */
+			MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07	0x1b0b0 /* Touch Reset */
+			MX6UL_PAD_SNVS_TAMPER8__GPIO5_IO08	0x1b0b0 /* Touch Wake */
+		>;
+	};
+
+	pinctrl_pwm7: pwm7grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_VSYNC__PWM7_OUT		0x110b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts b/arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts
new file mode 100644
index 000000000000..4206a4b3f0df
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts
@@ -0,0 +1,420 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+/dts-v1/;
+
+#include "imx6ul-kontron-n6310-som.dtsi"
+
+/ {
+	model = "Kontron N6310 S";
+	compatible = "kontron,imx6ul-n6310-s", "kontron,imx6ul-n6310-som",
+		     "fsl,imx6ul";
+
+	pwm-beeper {
+		compatible = "pwm-beeper";
+		pwms = <&pwm8 0 5000>;
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+
+		led1 {
+			label = "debug-led1";
+			gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+			linux,default-trigger = "heartbeat";
+		};
+
+		led2 {
+			label = "debug-led2";
+			gpios = <&gpio5 3 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led3 {
+			label = "debug-led3";
+			gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_vref_adc: regulator-vref-adc {
+		compatible = "regulator-fixed";
+		regulator-name = "vref-adc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&adc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc1>;
+	num-channels = <3>;
+	vref-supply = <&reg_vref_adc>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	status = "okay";
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	eeprom@0 {
+		compatible = "anvo,anv32e61w", "atmel,at25";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+		spi-cpha;
+		spi-cpol;
+		pagesize = <1>;
+		size = <8192>;
+		address-width = <16>;
+	};
+};
+
+&fec1 {
+	pinctrl-0 = <&pinctrl_enet1>;
+	/delete-node/ mdio;
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet2 &pinctrl_enet2_mdio>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy2>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@1 {
+			reg = <1>;
+			micrel,led-mode = <0>;
+			clocks = <&clks IMX6UL_CLK_ENET_REF>;
+			clock-names = "rmii-ref";
+		};
+
+		ethphy2: ethernet-phy@2 {
+			reg = <2>;
+			micrel,led-mode = <0>;
+			clocks = <&clks IMX6UL_CLK_ENET2_REF>;
+			clock-names = "rmii-ref";
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+};
+
+&i2c4 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	status = "okay";
+
+	rtc@32 {
+		compatible = "epson,rx8900";
+		reg = <0x32>;
+	};
+};
+
+&pwm8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm8>;
+	status = "okay";
+};
+
+&snvs_poweroff {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	linux,rs485-enabled-at-boot-time;
+	rs485-rx-during-tx;
+	rs485-rts-active-low;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	fsl,uart-has-rtscts;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1>;
+	dr_mode = "otg";
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	vbus-supply = <&reg_usb_otg1_vbus>;
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+	keep-power-in-suspend;
+	enable-sdio-wakeup;
+	vmmc-supply = <&reg_3v3>;
+	voltage-ranges = <3300 3300>;
+	no-1-8-v;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	non-removable;
+	keep-power-in-suspend;
+	enable-sdio-wakeup;
+	vmmc-supply = <&reg_3v3>;
+	voltage-ranges = <3300 3300>;
+	no-1-8-v;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	status = "okay";
+	fsl,ext-reset-output;
+};
+
+&iomuxc {
+	pinctrl-0 = <&pinctrl_reset_out &pinctrl_gpio>;
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO09__WDOG1_WDOG_ANY	0x30b0
+		>;
+	};
+
+	pinctrl_gpio: gpio {
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05	0x1b0b0 /* DOUT1 */
+			MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04	0x1b0b0 /* DIN1 */
+			MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x1b0b0 /* DOUT2 */
+			MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x1b0b0 /* DIN2 */
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1 {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO04__GPIO1_IO04	0x1b0b0
+		>;
+	};
+
+	pinctrl_gpio_leds: gpio_leds {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30	0x1b0b0	/* LED H14 */
+			MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x1b0b0	/* LED H15 */
+			MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x1b0b0	/* LED H16 */
+		>;
+	};
+
+	/* FRAM */
+	pinctrl_ecspi1: ecspi1grp-1 {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA07__ECSPI1_MISO	0x100b1
+			MX6UL_PAD_CSI_DATA06__ECSPI1_MOSI	0x100b1
+			MX6UL_PAD_CSI_DATA04__ECSPI1_SCLK	0x100b1
+			MX6UL_PAD_CSI_DATA05__GPIO4_IO26	0x100b1	/* ECSPI1-CS1 */
+		>;
+	};
+
+	pinctrl_enet2: enet2grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN	0x1b0b0
+			MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00	0x1b0b0
+			MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01	0x1b0b0
+			MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	0x4001b009
+		>;
+	};
+
+	pinctrl_enet2_mdio: enet2mdiogrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO07__ENET2_MDC         0x1b0b0
+			MX6UL_PAD_GPIO1_IO06__ENET2_MDIO        0x1b0b0
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2grp{
+		fsl,pins = <
+			MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX	0x1b020
+			MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX	0x1b020
+		>;
+	};
+
+	pinctrl_pwm8: pwm8grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_HSYNC__PWM8_OUT		0x110b0
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_DATA04__UART2_DCE_TX	0x1b0b1
+			MX6UL_PAD_NAND_DATA05__UART2_DCE_RX	0x1b0b1
+			MX6UL_PAD_NAND_DATA06__UART2_DCE_CTS	0x1b0b1
+			/*
+			 * mux unused RTS to make sure it doesn't cause
+			 * any interrupts when it is undefined
+			 */
+			MX6UL_PAD_NAND_DATA07__UART2_DCE_RTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX	0x1b0b1
+			MX6UL_PAD_UART3_CTS_B__UART3_DCE_CTS	0x1b0b1
+			MX6UL_PAD_UART3_RTS_B__UART3_DCE_RTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_TX_DATA__UART4_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART4_RX_DATA__UART4_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10059
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x100b1	/* SD1_CD */
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x10059
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x17059
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x17059
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x17059
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x17059
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x17059
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x100b9
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x170b9
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x170b9
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x170b9
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x170b9
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x100f9
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x170f9
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x170f9
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x170f9
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x170f9
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x170f9
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_PIXCLK__I2C1_SCL		0x4001b8b0
+			MX6UL_PAD_CSI_MCLK__I2C1_SDA		0x4001b8b0
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_TX_DATA__I2C4_SCL	0x4001f8b0
+			MX6UL_PAD_UART2_RX_DATA__I2C4_SDA	0x4001f8b0
+		>;
+	};
+
+	pinctrl_adc1: adc1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02	0xb0
+			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0xb0
+			MX6UL_PAD_GPIO1_IO08__GPIO1_IO08	0xb0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi b/arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi
new file mode 100644
index 000000000000..798ff0028e29
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#include "imx6ul.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Kontron N6310 SOM";
+	compatible = "kontron,imx6ul-n6310-som", "fsl,imx6ul";
+
+	memory@80000000 {
+		reg = <0x80000000 0x10000000>;
+		device_type = "memory";
+	};
+};
+
+&ecspi2 {
+	cs-gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	status = "okay";
+
+	spi-flash@0 {
+		compatible = "mxicy,mx25v8035f", "jedec,spi-nor";
+		spi-max-frequency = <50000000>;
+		reg = <0>;
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet1_mdio>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy1>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@1 {
+			reg = <1>;
+			micrel,led-mode = <0>;
+			clocks = <&clks IMX6UL_CLK_ENET_REF>;
+			clock-names = "rmii-ref";
+		};
+	};
+};
+
+&fec2 {
+	phy-mode = "rmii";
+	status = "disabled";
+};
+
+&qspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_qspi>;
+	status = "okay";
+
+	spi-flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "spi-nand";
+		spi-max-frequency = <108000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		reg = <0>;
+
+		partition@0 {
+			label = "ubi1";
+			reg = <0x00000000 0x08000000>;
+		};
+
+		partition@8000000 {
+			label = "ubi2";
+			reg = <0x08000000 0x08000000>;
+		};
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_reset_out>;
+
+	pinctrl_reset_out: rstoutgrp {
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09      0x1b0b0
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA03__ECSPI2_MISO      0x100b1
+			MX6UL_PAD_CSI_DATA02__ECSPI2_MOSI      0x100b1
+			MX6UL_PAD_CSI_DATA00__ECSPI2_SCLK      0x100b1
+			MX6UL_PAD_CSI_DATA01__GPIO4_IO22       0x100b1
+		>;
+	};
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN      0x1b0b0
+			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER      0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN      0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1  0x4001b009
+		>;
+	};
+
+	pinctrl_enet1_mdio: enet1mdiogrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO07__ENET1_MDC         0x1b0b0
+			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO        0x1b0b0
+		>;
+	};
+
+	pinctrl_qspi: qspigrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK        0x70a1
+			MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00   0x70a1
+			MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01     0x70a1
+			MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02     0x70a1
+			MX6UL_PAD_NAND_CLE__QSPI_A_DATA03       0x70a1
+			MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B        0x70a1
+		>;
+	};
+};
-- 
2.17.1