Re: [PATCH/RFC 04/12] dt-bindings: display: Add bindings for Advantech IDK-2121WR

[Laurent Pinchart <laurent.pinchart@ideasonboard.com>]

Hi Fabrizio,

Thank you for the patch.

On Fri, Aug 02, 2019 at 08:34:01AM +0100, Fabrizio Castro wrote:
> This panel is handled through the generic lvds-panel bindings,
> so only needs its additional compatible specified.
> 
> Some panel specific documentation can be found here:

s/panel specific/panel-specific/

> https://buy.advantech.eu/Displays/Embedded-LCD-Kits-High-Brightness/model-IDK-2121WR-K2FHA2E.htm
> 
> Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
> ---
>  .../display/panel/advantech,idk-2121wr.txt         | 62 ++++++++++++++++++++++
>  1 file changed, 62 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/panel/advantech,idk-2121wr.txt
> 
> diff --git a/Documentation/devicetree/bindings/display/panel/advantech,idk-2121wr.txt b/Documentation/devicetree/bindings/display/panel/advantech,idk-2121wr.txt
> new file mode 100644
> index 0000000..70b15b6
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/panel/advantech,idk-2121wr.txt
> @@ -0,0 +1,62 @@
> +Advantech Co., Ltd. IDK-2121WR 21.5" LVDS panel
> +===============================================
> +
> +Required properties:
> +- compatible: should be "advantech,idk-2121wr" followed by "panel-lvds"
> +
> +This binding is compatible with the lvds-panel binding, which is specified
> +in panel-lvds.txt in this directory.

How about adding "The panel operates in dual-link mode and thus requires
two port nodes." ?

> +
> +Example
> +-------
> +
> +	panel {
> +		compatible = "advantech,idk-2121wr", "panel-lvds";
> +
> +		width-mm = <476>;
> +		height-mm = <268>;
> +
> +		data-mapping = "vesa-24";
> +
> +		panel-timing {
> +			clock-frequency = <148500000>;
> +			hactive = <1920>;
> +			vactive = <1080>;
> +			hsync-len = <44>;
> +			hfront-porch = <88>;
> +			hback-porch = <148>;
> +			vfront-porch = <4>;
> +			vback-porch = <36>;
> +			vsync-len = <5>;
> +		};
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port@0 {
> +				reg = <0>;
> +				lvds0_panel_in: endpoint {
> +					remote-endpoint = <&lvds0_out>;
> +				};
> +			};
> +
> +			port@1 {
> +				reg = <1>;
> +				lvds1_panel_in: endpoint {
> +					remote-endpoint = <&lvds1_out>;
> +				};
> +			};
> +		};
> +	};
> +
> +	backlight: backlight {
> +		compatible = "pwm-backlight";
> +		pwms = <&pwm5 0 50000>;
> +
> +		brightness-levels = <0 4 8 16 32 64 128 255>;
> +		default-brightness-level = <6>;
> +
> +		power-supply = <&reg_12p0v>;
> +		enable-gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
> +	};

I think you can drop the backlight here, it's a bit out of scope.

-- 
Regards,

Laurent Pinchart