From: Alexandru Ardelean <alexandru.ardelean@analog.com>
To: <netdev@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-kernel@vger.kernel.org>
Cc: <davem@davemloft.net>, <robh+dt@kernel.org>,
<mark.rutland@arm.com>, <f.fainelli@gmail.com>,
<hkallweit1@gmail.com>, <andrew@lunn.ch>,
Alexandru Ardelean <alexandru.ardelean@analog.com>
Subject: [PATCH v4 00/14] net: phy: adin: add support for Analog Devices PHYs
Date: Mon, 12 Aug 2019 14:23:36 +0300 [thread overview]
Message-ID: <20190812112350.15242-1-alexandru.ardelean@analog.com> (raw)
This changeset adds support for Analog Devices Industrial Ethernet PHYs.
Particularly the PHYs this driver adds support for:
* ADIN1200 - Robust, Industrial, Low Power 10/100 Ethernet PHY
* ADIN1300 - Robust, Industrial, Low Latency 10/100/1000 Gigabit
Ethernet PHY
The 2 chips are register compatible with one another. The main
difference being that ADIN1200 doesn't operate in gigabit mode.
The chips can be operated by the Generic PHY driver as well via the
standard IEEE PHY registers (0x0000 - 0x000F) which are supported by the
kernel as well. This assumes that configuration of the PHY has been done
completely in HW, according to spec, i.e. no extra SW configuration
required.
This changeset also implements the ability to configure the chips via SW
registers.
Datasheets:
https://www.analog.com/media/en/technical-documentation/data-sheets/ADIN1300.pdf
https://www.analog.com/media/en/technical-documentation/data-sheets/ADIN1200.pdf
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Alexandru Ardelean (14):
net: phy: adin: add support for Analog Devices PHYs
net: phy: adin: hook genphy_{suspend,resume} into the driver
net: phy: adin: add support for interrupts
net: phy: adin: add {write,read}_mmd hooks
net: phy: adin: configure RGMII/RMII/MII modes on config
net: phy: adin: make RGMII internal delays configurable
net: phy: adin: make RMII fifo depth configurable
net: phy: adin: add support MDI/MDIX/Auto-MDI selection
net: phy: adin: add EEE translation layer from Clause 45 to Clause 22
net: phy: adin: implement PHY subsystem software reset
net: phy: adin: implement Energy Detect Powerdown mode
net: phy: adin: implement downshift configuration via phy-tunable
net: phy: adin: add ethtool get_stats support
dt-bindings: net: add bindings for ADIN PHY driver
.../devicetree/bindings/net/adi,adin.yaml | 73 ++
MAINTAINERS | 8 +
drivers/net/phy/Kconfig | 9 +
drivers/net/phy/Makefile | 1 +
drivers/net/phy/adin.c | 763 ++++++++++++++++++
5 files changed, 854 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/adi,adin.yaml
create mode 100644 drivers/net/phy/adin.c
--
Changelog v3 -> v4:
* [PATCH v3 03/14] net: phy: adin: add support for interrupts
- using only Link status interrupt
* [PATCH v3 04/14] net: phy: adin: add {write,read}_mmd hooks
- dropped C45 access code; it is dead-code, since `is_c45` will never be true
2.20.1
next reply other threads:[~2019-08-12 11:25 UTC|newest]
Thread overview: 40+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-08-12 11:23 Alexandru Ardelean [this message]
2019-08-12 11:23 ` [PATCH v4 01/14] net: phy: adin: add support for Analog Devices PHYs Alexandru Ardelean
2019-08-14 17:47 ` Florian Fainelli
2019-08-12 11:23 ` [PATCH v4 02/14] net: phy: adin: hook genphy_{suspend,resume} into the driver Alexandru Ardelean
2019-08-14 17:47 ` Florian Fainelli
2019-08-12 11:23 ` [PATCH v4 03/14] net: phy: adin: add support for interrupts Alexandru Ardelean
2019-08-14 17:48 ` Florian Fainelli
2019-08-12 11:23 ` [PATCH v4 04/14] net: phy: adin: add {write,read}_mmd hooks Alexandru Ardelean
2019-08-12 14:06 ` Andrew Lunn
2019-08-14 17:49 ` Florian Fainelli
2019-08-12 11:23 ` [PATCH v4 05/14] net: phy: adin: configure RGMII/RMII/MII modes on config Alexandru Ardelean
2019-08-14 17:50 ` Florian Fainelli
2019-08-12 11:23 ` [PATCH v4 06/14] net: phy: adin: make RGMII internal delays configurable Alexandru Ardelean
2019-08-14 17:52 ` Florian Fainelli
2019-08-12 11:23 ` [PATCH v4 07/14] net: phy: adin: make RMII fifo depth configurable Alexandru Ardelean
2019-08-14 17:53 ` Florian Fainelli
2019-08-12 11:23 ` [PATCH v4 08/14] net: phy: adin: add support MDI/MDIX/Auto-MDI selection Alexandru Ardelean
2019-08-14 17:54 ` Florian Fainelli
2019-08-12 11:23 ` [PATCH v4 09/14] net: phy: adin: add EEE translation layer from Clause 45 to Clause 22 Alexandru Ardelean
2019-08-12 14:08 ` Andrew Lunn
2019-08-14 17:55 ` Florian Fainelli
2019-08-12 11:23 ` [PATCH v4 10/14] net: phy: adin: implement PHY subsystem software reset Alexandru Ardelean
2019-08-12 14:19 ` Andrew Lunn
2019-08-13 5:42 ` Ardelean, Alexandru
2019-08-12 11:23 ` [PATCH v4 11/14] net: phy: adin: implement Energy Detect Powerdown mode Alexandru Ardelean
2019-08-14 17:57 ` Florian Fainelli
2019-08-16 6:09 ` Ardelean, Alexandru
2019-08-12 11:23 ` [PATCH v4 12/14] net: phy: adin: implement downshift configuration via phy-tunable Alexandru Ardelean
2019-08-12 14:21 ` Andrew Lunn
2019-08-14 17:58 ` Florian Fainelli
2019-08-12 11:23 ` [PATCH v4 13/14] net: phy: adin: add ethtool get_stats support Alexandru Ardelean
2019-08-12 14:26 ` Andrew Lunn
2019-08-13 6:07 ` Ardelean, Alexandru
2019-08-12 14:33 ` Andrew Lunn
2019-08-13 5:48 ` Ardelean, Alexandru
2019-08-14 9:08 ` Ardelean, Alexandru
2019-08-14 14:04 ` Andrew Lunn
2019-08-12 11:23 ` [PATCH v4 14/14] dt-bindings: net: add bindings for ADIN PHY driver Alexandru Ardelean
2019-08-12 14:34 ` Andrew Lunn
2019-08-12 19:02 ` Rob Herring
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190812112350.15242-1-alexandru.ardelean@analog.com \
--to=alexandru.ardelean@analog.com \
--cc=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=f.fainelli@gmail.com \
--cc=hkallweit1@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=netdev@vger.kernel.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).