linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Andrew Murray <andrew.murray@arm.com>
To: Pankaj Dubey <pankaj.dubey@samsung.com>
Cc: linux-pci@vger.kernel.org, linux-kernel@vger.kernel.org,
	Jingoo Han <jingoohan1@gmail.com>,
	gustavo.pimentel@synopsys.com, lorenzo.pieralisi@arm.com,
	Bjorn Helgaas <bhelgaas@google.com>,
	Anvesh Salveru <anvesh.s@samsung.com>
Subject: Re: [PATCH 1/2] PCI: dwc: Add support to disable GEN3 equalization
Date: Wed, 11 Sep 2019 10:23:11 +0100	[thread overview]
Message-ID: <20190911092310.GN9720@e119886-lin.cambridge.arm.com> (raw)
In-Reply-To: <CAGcde9F6dTGga6Rxo62PPk3AMb3tK8oqo9K6Zi=0TbnFktmQQw@mail.gmail.com>

On Tue, Sep 10, 2019 at 09:46:28PM +0530, Pankaj Dubey wrote:
> On Tue, 10 Sep 2019 at 19:56, Andrew Murray <andrew.murray@arm.com> wrote:
> >
> > On Tue, Sep 10, 2019 at 05:55:01PM +0530, Pankaj Dubey wrote:
> > > From: Anvesh Salveru <anvesh.s@samsung.com>
> > >
> > > In some platforms, PCIe PHY may have issues which will prevent linkup
> > > to happen in GEN3 or high speed. In case equalization fails, link will
> > > fallback to GEN1.
> >
> > When you refer to "high speed", do you mean "higher speeds" as in GEN3,
> > GEN4, etc?
> >
> 
> Yes. Will reword the commit message as "higher speeds"
> 
> > >
> > > Designware controller has support for disabling GEN3 equalization if
> > > required. This patch enables the designware driver to disable the PCIe
> > > GEN3 equalization by writing into PCIE_PORT_GEN3_RELATED.
> >
> > Thus limiting to GEN2 speeds max, right?
> >
> > Is the purpose of PORT_LOGIC_GEN3_EQ_DISABLE to disable GEN3 and above
> > even though we advertise GEN3 and above speeds? I.e. the IP advertises
> > GEN3 but the phy can't handle it, we can't change what the IP advertises
> > and so we disable equalization to limit to GEN2?
> >
> > I notice many of the other dwc drivers (dra7xx, keystone, tegra194, imx6)
> > seem to use the device tree to specify a max-link-speed and then impose
> > that limit by changing the value in PCI_EXP_LNKCAP. Is your
> > PORT_LOGIC_GEN3_EQ_DISABLE approach and alternative to the PCI_EXP_LNKCAP
> > approach, or does your approach add something else?
> >
> 
> No, max speed will be still as per advertised by link or it will be
> equal to the limited speed as per DT property if any.
> This register will prohibit to perform all phases of equalization and
> thus allowing link to happen in maximum supported/advertised speed.
> 
> This is not to limit max link speed, this register helps link to
> happen in higher speeds (GEN3/4) without going through equalization
> phases. It is intended to use only if at all link fails to latch up in
> GEN3/4 due to failure in equalization phases.

I thought that for GEN3 and beyond equalization was *required* - with only
phases 2 and 3 being optional. Therefore I'm suprised to see that if
equalization does fail we continue to train the link anyway. Have I
understood this correctly?

Also are there any plans to provide patches to use this quirk on any
drivers?

> 
> > >
> > > Platform drivers can disable equalization by setting the dwc_pci_quirk
> > > flag DWC_EQUALIZATION_DISABLE.
> > >
> > > Signed-off-by: Anvesh Salveru <anvesh.s@samsung.com>
> > > Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
> > > ---
> > >  drivers/pci/controller/dwc/pcie-designware.c | 7 +++++++
> > >  drivers/pci/controller/dwc/pcie-designware.h | 7 +++++++
> > >  2 files changed, 14 insertions(+)
> > >
> > > diff --git a/drivers/pci/controller/dwc/pcie-designware.c b/drivers/pci/controller/dwc/pcie-designware.c
> > > index 7d25102..bf82091 100644
> > > --- a/drivers/pci/controller/dwc/pcie-designware.c
> > > +++ b/drivers/pci/controller/dwc/pcie-designware.c
> > > @@ -466,4 +466,11 @@ void dw_pcie_setup(struct dw_pcie *pci)
> > >               break;
> > >       }
> > >       dw_pcie_writel_dbi(pci, PCIE_LINK_WIDTH_SPEED_CONTROL, val);
> > > +
> > > +     val = dw_pcie_readl_dbi(pci, PCIE_PORT_GEN3_RELATED);
> > > +
> > > +     if (pci->dwc_pci_quirk & DWC_EQUALIZATION_DISABLE)
> > > +             val |= PORT_LOGIC_GEN3_EQ_DISABLE;
> > > +
> > > +     dw_pcie_writel_dbi(pci, PCIE_PORT_GEN3_RELATED, val);
> >
> > The problem here is that even when DWC_EQUALIZATION_DISABLE is not set
> > the driver will read and write PCIE_PORT_GEN3_RELATED when it is not
> > needed. How about something like:
> >
> > > +
> > > +     if (pci->dwc_pci_quirk & DWC_EQUALIZATION_DISABLE) {
> > > +             val = dw_pcie_readl_dbi(pci, PCIE_PORT_GEN3_RELATED);
> > > +             val |= PORT_LOGIC_GEN3_EQ_DISABLE;
> > > +             dw_pcie_writel_dbi(pci, PCIE_PORT_GEN3_RELATED, val);
> > > +     }
> >
> 
> Yes, before posting we taught about it, but then next patchset is
> adding one more quirk and in that case we need to repeat read and
> write under each if condition. I hope that repetition should be fine.

I understand. I think the repetition is prefered over needlessly reading and
writing registers.

Given these quirks are so similar, I wouldn't have a problem with them being
in the same patch.

Thanks,

Andrew Murray

> 
> > >  }
> > > diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h
> > > index ffed084..a1453c5 100644
> > > --- a/drivers/pci/controller/dwc/pcie-designware.h
> > > +++ b/drivers/pci/controller/dwc/pcie-designware.h
> > > @@ -29,6 +29,9 @@
> > >  #define LINK_WAIT_MAX_IATU_RETRIES   5
> > >  #define LINK_WAIT_IATU                       9
> > >
> > > +/* Parameters for PCIe Quirks */
> > > +#define DWC_EQUALIZATION_DISABLE     0x1
> >
> > How about using BIT(1) instead? Thus implying that you can combine
> > quirks.
> >
> 
> Agreed.
> 
> > Thanks,
> >
> > Andrew Murray
> >
> > > +
> > >  /* Synopsys-specific PCIe configuration registers */
> > >  #define PCIE_PORT_LINK_CONTROL               0x710
> > >  #define PORT_LINK_MODE_MASK          GENMASK(21, 16)
> > > @@ -60,6 +63,9 @@
> > >  #define PCIE_MSI_INTR0_MASK          0x82C
> > >  #define PCIE_MSI_INTR0_STATUS                0x830
> > >
> > > +#define PCIE_PORT_GEN3_RELATED               0x890
> > > +#define PORT_LOGIC_GEN3_EQ_DISABLE   BIT(16)
> > > +
> > >  #define PCIE_ATU_VIEWPORT            0x900
> > >  #define PCIE_ATU_REGION_INBOUND              BIT(31)
> > >  #define PCIE_ATU_REGION_OUTBOUND     0
> > > @@ -244,6 +250,7 @@ struct dw_pcie {
> > >       struct dw_pcie_ep       ep;
> > >       const struct dw_pcie_ops *ops;
> > >       unsigned int            version;
> > > +     unsigned int            dwc_pci_quirk;
> > >  };
> > >
> > >  #define to_dw_pcie_from_pp(port) container_of((port), struct dw_pcie, pp)
> > > --
> > > 2.7.4
> > >

  reply	other threads:[~2019-09-11  9:23 UTC|newest]

Thread overview: 13+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
     [not found] <CGME20190910122514epcas5p4f00c0f999333dd7707c0a353fd06b57f@epcas5p4.samsung.com>
2019-09-10 12:25 ` Pankaj Dubey
     [not found]   ` <CGME20190910122520epcas5p1faeb16f7c38ee057ce93783a637e6bf4@epcas5p1.samsung.com>
2019-09-10 12:25     ` [PATCH 2/2] PCI: dwc: Add support to disable equalization phase 2 and 3 Pankaj Dubey
2019-09-10 14:05       ` Andrew Murray
2019-09-10 16:21         ` Pankaj Dubey
2019-09-11  9:27           ` Andrew Murray
2019-09-12 11:44             ` Pankaj Dubey
2019-09-10 13:58   ` [PATCH 1/2] PCI: dwc: Add support to disable GEN3 equalization Andrew Murray
2019-09-10 16:16     ` Pankaj Dubey
2019-09-11  9:23       ` Andrew Murray [this message]
2019-09-12 11:39         ` Pankaj Dubey
2019-09-12 12:42           ` Andrew Murray
2019-09-12 14:21   ` Gustavo Pimentel
2019-09-13 10:53     ` Pankaj Dubey

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190911092310.GN9720@e119886-lin.cambridge.arm.com \
    --to=andrew.murray@arm.com \
    --cc=anvesh.s@samsung.com \
    --cc=bhelgaas@google.com \
    --cc=gustavo.pimentel@synopsys.com \
    --cc=jingoohan1@gmail.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-pci@vger.kernel.org \
    --cc=lorenzo.pieralisi@arm.com \
    --cc=pankaj.dubey@samsung.com \
    --subject='Re: [PATCH 1/2] PCI: dwc: Add support to disable GEN3 equalization' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).