linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
* [PATCH v3 1/2] dt-bindings: pwm: Convert PWM bindings to json-schema
@ 2019-10-02 16:40 Krzysztof Kozlowski
  2019-10-02 16:40 ` [PATCH v3 2/2] dt-bindings: pwm: Convert Samsung " Krzysztof Kozlowski
                   ` (2 more replies)
  0 siblings, 3 replies; 5+ messages in thread
From: Krzysztof Kozlowski @ 2019-10-02 16:40 UTC (permalink / raw)
  To: Rob Herring, Mark Rutland, Thierry Reding, Uwe Kleine-König,
	linux-clk, devicetree, linux-kernel, dri-devel, linux-leds,
	linux-pwm, linux-arm-kernel, linux-tegra,
	bcm-kernel-feedback-list, linux-rpi-kernel, linux-amlogic,
	linux-mediatek, linux-rockchip, linux-riscv, linux-stm32
  Cc: Krzysztof Kozlowski

Convert generic PWM bindings to DT schema format using json-schema.  The
consumer bindings are split to separate file.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

---

Changes since v2:
1. Change also pwm-sprd.txt

Changes since v1:
1. Indent example with four spaces (more readable),
2. Change pattern for pwm nodes,
3. Remove $ref from #cells.
---
 .../devicetree/bindings/clock/pwm-clock.txt   |  2 +-
 .../bindings/display/bridge/ti,sn65dsi86.txt  |  2 +-
 .../devicetree/bindings/display/ssd1307fb.txt |  2 +-
 .../bindings/leds/backlight/pwm-backlight.txt |  2 +-
 .../devicetree/bindings/leds/leds-pwm.txt     |  2 +-
 .../devicetree/bindings/mfd/max77693.txt      |  2 +-
 .../bindings/pwm/atmel-hlcdc-pwm.txt          |  2 +-
 .../devicetree/bindings/pwm/atmel-pwm.txt     |  2 +-
 .../devicetree/bindings/pwm/atmel-tcb-pwm.txt |  2 +-
 .../bindings/pwm/brcm,bcm7038-pwm.txt         |  2 +-
 .../bindings/pwm/brcm,iproc-pwm.txt           |  2 +-
 .../devicetree/bindings/pwm/brcm,kona-pwm.txt |  2 +-
 .../devicetree/bindings/pwm/img-pwm.txt       |  2 +-
 .../devicetree/bindings/pwm/imx-pwm.txt       |  2 +-
 .../devicetree/bindings/pwm/imx-tpm-pwm.txt   |  2 +-
 .../bindings/pwm/lpc1850-sct-pwm.txt          |  2 +-
 .../devicetree/bindings/pwm/mxs-pwm.txt       |  2 +-
 .../bindings/pwm/nvidia,tegra20-pwm.txt       |  2 +-
 .../bindings/pwm/nxp,pca9685-pwm.txt          |  2 +-
 .../devicetree/bindings/pwm/pwm-bcm2835.txt   |  2 +-
 .../devicetree/bindings/pwm/pwm-berlin.txt    |  2 +-
 .../bindings/pwm/pwm-consumers.yaml           | 76 +++++++++++++++++++
 .../devicetree/bindings/pwm/pwm-fsl-ftm.txt   |  2 +-
 .../devicetree/bindings/pwm/pwm-hibvt.txt     |  2 +-
 .../devicetree/bindings/pwm/pwm-lp3943.txt    |  2 +-
 .../devicetree/bindings/pwm/pwm-mediatek.txt  |  2 +-
 .../devicetree/bindings/pwm/pwm-meson.txt     |  2 +-
 .../devicetree/bindings/pwm/pwm-mtk-disp.txt  |  2 +-
 .../bindings/pwm/pwm-omap-dmtimer.txt         |  2 +-
 .../devicetree/bindings/pwm/pwm-rockchip.txt  |  2 +-
 .../devicetree/bindings/pwm/pwm-sifive.txt    |  2 +-
 .../devicetree/bindings/pwm/pwm-sprd.txt      |  4 +-
 .../devicetree/bindings/pwm/pwm-stm32-lp.txt  |  2 +-
 .../devicetree/bindings/pwm/pwm-stm32.txt     |  2 +-
 .../devicetree/bindings/pwm/pwm-tiecap.txt    |  2 +-
 .../devicetree/bindings/pwm/pwm-tiehrpwm.txt  |  2 +-
 .../devicetree/bindings/pwm/pwm-zx.txt        |  2 +-
 Documentation/devicetree/bindings/pwm/pwm.txt | 69 -----------------
 .../devicetree/bindings/pwm/pwm.yaml          | 29 +++++++
 .../bindings/pwm/renesas,pwm-rcar.txt         |  2 +-
 .../bindings/pwm/renesas,tpu-pwm.txt          |  4 +-
 .../devicetree/bindings/pwm/spear-pwm.txt     |  2 +-
 .../devicetree/bindings/pwm/st,stmpe-pwm.txt  |  2 +-
 .../devicetree/bindings/pwm/ti,twl-pwm.txt    |  2 +-
 .../devicetree/bindings/pwm/ti,twl-pwmled.txt |  2 +-
 .../devicetree/bindings/pwm/vt8500-pwm.txt    |  2 +-
 .../bindings/regulator/pwm-regulator.txt      |  2 +-
 .../devicetree/bindings/timer/ingenic,tcu.txt |  2 +-
 48 files changed, 152 insertions(+), 116 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/pwm/pwm-consumers.yaml
 delete mode 100644 Documentation/devicetree/bindings/pwm/pwm.txt
 create mode 100644 Documentation/devicetree/bindings/pwm/pwm.yaml

diff --git a/Documentation/devicetree/bindings/clock/pwm-clock.txt b/Documentation/devicetree/bindings/clock/pwm-clock.txt
index 83db876b3b90..8a791b6d76a9 100644
--- a/Documentation/devicetree/bindings/clock/pwm-clock.txt
+++ b/Documentation/devicetree/bindings/clock/pwm-clock.txt
@@ -3,7 +3,7 @@ Binding for an external clock signal driven by a PWM pin.
 This binding uses the common clock binding[1] and the common PWM binding[2].
 
 [1] Documentation/devicetree/bindings/clock/clock-bindings.txt
-[2] Documentation/devicetree/bindings/pwm/pwm.txt
+[2] Documentation/devicetree/bindings/pwm/pwm-consumers.yaml
 
 Required properties:
 - compatible : shall be "pwm-clock".
diff --git a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
index 0a3fbb53a16e..8ec4a7f2623a 100644
--- a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
+++ b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
@@ -21,7 +21,7 @@ Optional properties:
 - #gpio-cells    : Should be two. The first cell is the pin number and
                    the second cell is used to specify flags.
                    See ../../gpio/gpio.txt for more information.
-- #pwm-cells : Should be one. See ../../pwm/pwm.txt for description of
+- #pwm-cells : Should be one. See ../../pwm/pwm.yaml for description of
                the cell formats.
 
 - clock-names: should be "refclk"
diff --git a/Documentation/devicetree/bindings/display/ssd1307fb.txt b/Documentation/devicetree/bindings/display/ssd1307fb.txt
index 27333b9551b3..da9b28153a3c 100644
--- a/Documentation/devicetree/bindings/display/ssd1307fb.txt
+++ b/Documentation/devicetree/bindings/display/ssd1307fb.txt
@@ -37,7 +37,7 @@ Optional properties:
   - solomon,area-color-enable: Display uses color mode
   - solomon,low-power. Display runs in low power mode
 
-[0]: Documentation/devicetree/bindings/pwm/pwm.txt
+[0]: Documentation/devicetree/bindings/pwm/pwm-consumers.yaml
 
 Examples:
 ssd1307: oled@3c {
diff --git a/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt b/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt
index 64fa2fbd98c9..8dbbadd3af96 100644
--- a/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt
+++ b/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt
@@ -28,7 +28,7 @@ Optional properties:
                             having to list out every possible value in the
                             brightness-level array.
 
-[0]: Documentation/devicetree/bindings/pwm/pwm.txt
+[0]: Documentation/devicetree/bindings/pwm/pwm-consumers.yaml
 [1]: Documentation/devicetree/bindings/gpio/gpio.txt
 
 Example:
diff --git a/Documentation/devicetree/bindings/leds/leds-pwm.txt b/Documentation/devicetree/bindings/leds/leds-pwm.txt
index 6c6583c35f2f..aeaa250668d5 100644
--- a/Documentation/devicetree/bindings/leds/leds-pwm.txt
+++ b/Documentation/devicetree/bindings/leds/leds-pwm.txt
@@ -11,7 +11,7 @@ LED sub-node properties:
   specify the period time to be used: <&phandle id period_ns>;
 - pwm-names : (optional) Name to be used by the PWM subsystem for the PWM device
   For the pwms and pwm-names property please refer to:
-  Documentation/devicetree/bindings/pwm/pwm.txt
+  Documentation/devicetree/bindings/pwm/pwm-consumers.yaml
 - max-brightness : Maximum brightness possible for the LED
 - active-low : (optional) For PWMs where the LED is wired to supply
   rather than ground.
diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt
index a3c60a7a3be1..1e6318695eb2 100644
--- a/Documentation/devicetree/bindings/mfd/max77693.txt
+++ b/Documentation/devicetree/bindings/mfd/max77693.txt
@@ -38,7 +38,7 @@ Optional properties:
 	 PWM properties should be named "pwms". And number of cell is different
 	 for each pwm device.
 	 To get more information, please refer to documentation.
-	[*] refer Documentation/devicetree/bindings/pwm/pwm.txt
+	[*] refer Documentation/devicetree/bindings/pwm/pwm-consumers.yaml
 
 - charger : Node configuring the charger driver.
   If present, required properties:
diff --git a/Documentation/devicetree/bindings/pwm/atmel-hlcdc-pwm.txt b/Documentation/devicetree/bindings/pwm/atmel-hlcdc-pwm.txt
index cfda0d57d302..afa501bf7f94 100644
--- a/Documentation/devicetree/bindings/pwm/atmel-hlcdc-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/atmel-hlcdc-pwm.txt
@@ -10,7 +10,7 @@ Required properties:
  - pinctrl-0: should contain the pinctrl states described by pinctrl
    default.
  - #pwm-cells: should be set to 3. This PWM chip use the default 3 cells
-   bindings defined in pwm.txt in this directory.
+   bindings defined in pwm.yaml in this directory.
 
 Example:
 
diff --git a/Documentation/devicetree/bindings/pwm/atmel-pwm.txt b/Documentation/devicetree/bindings/pwm/atmel-pwm.txt
index 591ecdd39c7b..fbb5325be1f0 100644
--- a/Documentation/devicetree/bindings/pwm/atmel-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/atmel-pwm.txt
@@ -7,7 +7,7 @@ Required properties:
     - "atmel,sama5d2-pwm"
     - "microchip,sam9x60-pwm"
   - reg: physical base address and length of the controller's registers
-  - #pwm-cells: Should be 3. See pwm.txt in this directory for a
+  - #pwm-cells: Should be 3. See pwm.yaml in this directory for a
     description of the cells format.
 
 Example:
diff --git a/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt b/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt
index 8031148bcf85..985fcc65f8c4 100644
--- a/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt
@@ -2,7 +2,7 @@ Atmel TCB PWM controller
 
 Required properties:
 - compatible: should be "atmel,tcb-pwm"
-- #pwm-cells: should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 3. See pwm.yaml in this directory for a description of
   the cells format. The only third cell flag supported by this binding is
   PWM_POLARITY_INVERTED.
 - tc-block: The Timer Counter block to use as a PWM chip.
diff --git a/Documentation/devicetree/bindings/pwm/brcm,bcm7038-pwm.txt b/Documentation/devicetree/bindings/pwm/brcm,bcm7038-pwm.txt
index d9254a6da5ed..0e662d7f6bd1 100644
--- a/Documentation/devicetree/bindings/pwm/brcm,bcm7038-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/brcm,bcm7038-pwm.txt
@@ -4,7 +4,7 @@ Required properties:
 
 - compatible: must be "brcm,bcm7038-pwm"
 - reg: physical base address and length for this controller
-- #pwm-cells: should be 2. See pwm.txt in this directory for a description
+- #pwm-cells: should be 2. See pwm.yaml in this directory for a description
   of the cells format
 - clocks: a phandle to the reference clock for this block which is fed through
   its internal variable clock frequency generator
diff --git a/Documentation/devicetree/bindings/pwm/brcm,iproc-pwm.txt b/Documentation/devicetree/bindings/pwm/brcm,iproc-pwm.txt
index 21f75bbd6dae..655f6cd4ef46 100644
--- a/Documentation/devicetree/bindings/pwm/brcm,iproc-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/brcm,iproc-pwm.txt
@@ -6,7 +6,7 @@ Required Properties :
 - compatible: must be "brcm,iproc-pwm"
 - reg: physical base address and length of the controller's registers
 - clocks: phandle + clock specifier pair for the external clock
-- #pwm-cells: Should be 3. See pwm.txt in this directory for a
+- #pwm-cells: Should be 3. See pwm.yaml in this directory for a
   description of the cells format.
 
 Refer to clocks/clock-bindings.txt for generic clock consumer properties.
diff --git a/Documentation/devicetree/bindings/pwm/brcm,kona-pwm.txt b/Documentation/devicetree/bindings/pwm/brcm,kona-pwm.txt
index 8eae9fe7841c..c42eecfc81ed 100644
--- a/Documentation/devicetree/bindings/pwm/brcm,kona-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/brcm,kona-pwm.txt
@@ -6,7 +6,7 @@ Required Properties :
 - compatible: should contain "brcm,kona-pwm"
 - reg: physical base address and length of the controller's registers
 - clocks: phandle + clock specifier pair for the external clock
-- #pwm-cells: Should be 3. See pwm.txt in this directory for a
+- #pwm-cells: Should be 3. See pwm.yaml in this directory for a
   description of the cells format.
 
 Refer to clocks/clock-bindings.txt for generic clock consumer properties.
diff --git a/Documentation/devicetree/bindings/pwm/img-pwm.txt b/Documentation/devicetree/bindings/pwm/img-pwm.txt
index fade5f26fcac..9db6de97317d 100644
--- a/Documentation/devicetree/bindings/pwm/img-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/img-pwm.txt
@@ -8,7 +8,7 @@ Required properties:
   - clock-names: Must include the following entries.
     - pwm: PWM operating clock.
     - sys: PWM system interface clock.
-  - #pwm-cells: Should be 2. See pwm.txt in this directory for the
+  - #pwm-cells: Should be 2. See pwm.yaml in this directory for the
 	description of the cells format.
   - img,cr-periph: Must contain a phandle to the peripheral control
 	syscon node which contains PWM control registers.
diff --git a/Documentation/devicetree/bindings/pwm/imx-pwm.txt b/Documentation/devicetree/bindings/pwm/imx-pwm.txt
index c61bdf8cd41b..22f1c3d8b773 100644
--- a/Documentation/devicetree/bindings/pwm/imx-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/imx-pwm.txt
@@ -6,7 +6,7 @@ Required properties:
   - "fsl,imx1-pwm" for PWM compatible with the one integrated on i.MX1
   - "fsl,imx27-pwm" for PWM compatible with the one integrated on i.MX27
 - reg: physical base address and length of the controller's registers
-- #pwm-cells: 2 for i.MX1 and 3 for i.MX27 and newer SoCs. See pwm.txt
+- #pwm-cells: 2 for i.MX1 and 3 for i.MX27 and newer SoCs. See pwm.yaml
   in this directory for a description of the cells format.
 - clocks : Clock specifiers for both ipg and per clocks.
 - clock-names : Clock names should include both "ipg" and "per"
diff --git a/Documentation/devicetree/bindings/pwm/imx-tpm-pwm.txt b/Documentation/devicetree/bindings/pwm/imx-tpm-pwm.txt
index 3ba958d764ff..5bf20950a24e 100644
--- a/Documentation/devicetree/bindings/pwm/imx-tpm-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/imx-tpm-pwm.txt
@@ -3,7 +3,7 @@ Freescale i.MX TPM PWM controller
 Required properties:
 - compatible : Should be "fsl,imx7ulp-pwm".
 - reg: Physical base address and length of the controller's registers.
-- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of the cells format.
+- #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of the cells format.
 - clocks : The clock provided by the SoC to drive the PWM.
 - interrupts: The interrupt for the PWM controller.
 
diff --git a/Documentation/devicetree/bindings/pwm/lpc1850-sct-pwm.txt b/Documentation/devicetree/bindings/pwm/lpc1850-sct-pwm.txt
index 36e49d4325cd..43d9f4f08a2e 100644
--- a/Documentation/devicetree/bindings/pwm/lpc1850-sct-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/lpc1850-sct-pwm.txt
@@ -7,7 +7,7 @@ Required properties:
     See ../clock/clock-bindings.txt for details.
   - clock-names: Must include the following entries.
     - pwm: PWM operating clock.
-  - #pwm-cells: Should be 3. See pwm.txt in this directory for the description
+  - #pwm-cells: Should be 3. See pwm.yaml in this directory for the description
     of the cells format.
 
 Example:
diff --git a/Documentation/devicetree/bindings/pwm/mxs-pwm.txt b/Documentation/devicetree/bindings/pwm/mxs-pwm.txt
index 96cdde5f6208..1b06f86a7091 100644
--- a/Documentation/devicetree/bindings/pwm/mxs-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/mxs-pwm.txt
@@ -3,7 +3,7 @@ Freescale MXS PWM controller
 Required properties:
 - compatible: should be "fsl,imx23-pwm"
 - reg: physical base address and length of the controller's registers
-- #pwm-cells: should be 2. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 2. See pwm.yaml in this directory for a description of
   the cells format.
 - fsl,pwm-number: the number of PWM devices
 
diff --git a/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt b/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt
index c57e11b8d937..0a69eadf44ce 100644
--- a/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt
@@ -10,7 +10,7 @@ Required properties:
   - "nvidia,tegra210-pwm", "nvidia,tegra20-pwm": for Tegra210
   - "nvidia,tegra186-pwm": for Tegra186
 - reg: physical base address and length of the controller's registers
-- #pwm-cells: should be 2. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 2. See pwm.yaml in this directory for a description of
   the cells format.
 - clocks: Must contain one entry, for the module clock.
   See ../clocks/clock-bindings.txt for details.
diff --git a/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt b/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt
index f84ec9d291ea..f21b55c95738 100644
--- a/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt
@@ -3,7 +3,7 @@ NXP PCA9685 16-channel 12-bit PWM LED controller
 
 Required properties:
   - compatible: "nxp,pca9685-pwm"
-  - #pwm-cells: Should be 2. See pwm.txt in this directory for a description of
+  - #pwm-cells: Should be 2. See pwm.yaml in this directory for a description of
     the cells format.
     The index 16 is the ALLCALL channel, that sets all PWM channels at the same
     time.
diff --git a/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt b/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt
index 8cf87d1bfca5..f5753b3f79df 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt
@@ -6,7 +6,7 @@ Required properties:
 - clocks: This clock defines the base clock frequency of the PWM hardware
   system, the period and the duty_cycle of the PWM signal is a multiple of
   the base period.
-- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of
   the cells format.
 
 Examples:
diff --git a/Documentation/devicetree/bindings/pwm/pwm-berlin.txt b/Documentation/devicetree/bindings/pwm/pwm-berlin.txt
index 82cbe16fcbbc..f01e993a498a 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-berlin.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-berlin.txt
@@ -4,7 +4,7 @@ Required properties:
 - compatible: should be "marvell,berlin-pwm"
 - reg: physical base address and length of the controller's registers
 - clocks: phandle to the input clock
-- #pwm-cells: should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 3. See pwm.yaml in this directory for a description of
   the cells format.
 
 Example:
diff --git a/Documentation/devicetree/bindings/pwm/pwm-consumers.yaml b/Documentation/devicetree/bindings/pwm/pwm-consumers.yaml
new file mode 100644
index 000000000000..39c844fe6338
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/pwm-consumers.yaml
@@ -0,0 +1,76 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pwm/pwm-consumers.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Specifying PWM information for devices
+
+maintainers:
+  - Thierry Reding <thierry.reding@gmail.com>
+
+description: |
+  PWM properties should be named "pwms". The exact meaning of each pwms
+  property must be documented in the device tree binding for each device.
+  An optional property "pwm-names" may contain a list of strings to label
+  each of the PWM devices listed in the "pwms" property. If no "pwm-names"
+  property is given, the name of the user node will be used as fallback.
+
+  Drivers for devices that use more than a single PWM device can use the
+  "pwm-names" property to map the name of the PWM device requested by the
+  pwm_get() call to an index into the list given by the "pwms" property.
+
+properties:
+  pwms:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    description: |
+      Phandle to PWM controller node and pwm-specifier (controller specific).
+      pwm-specifier typically encodes the chip-relative PWM number and the PWM
+      period in nanoseconds.
+      Optionally, the pwm-specifier can encode a number of flags (defined in
+      <dt-bindings/pwm/pwm.h>) in a third cell:
+        - PWM_POLARITY_INVERTED: invert the PWM signal polarity
+
+  pwm-names:
+    $ref: /schemas/types.yaml#/definitions/string-array
+    description:
+      A list of strings to label each of the PWM devices listed in the "pwms"
+      property. If no "pwm-names" property is given, the name of the user node
+      will be used as fallback.
+
+required:
+  - pwms
+
+dependencies:
+  pwm-names: [ pwms ]
+
+examples:
+  - |
+    // The following example could be used to describe a PWM-based
+    // backlight device:
+
+    pwm: pwm {
+      #pwm-cells = <2>;
+    };
+
+    bl: backlight {
+      pwms = <&pwm 0 5000000>;
+      pwm-names = "backlight";
+    };
+
+    // Note that in the example above, specifying the "pwm-names" is redundant
+    // because the name "backlight" would be used as fallback anyway.
+
+  - |
+    // Example with optional PWM specifier for inverse polarity
+
+    #include <dt-bindings/pwm/pwm.h>
+
+    pwm2: pwm {
+      #pwm-cells = <3>;
+    };
+
+    backlight {
+      pwms = <&pwm2 0 5000000 PWM_POLARITY_INVERTED>;
+      pwm-names = "backlight";
+    };
diff --git a/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt b/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt
index 576ad002bc83..36532cd5ab25 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt
@@ -21,7 +21,7 @@ Required properties:
   - "fsl,vf610-ftm-pwm" for PWM compatible with the one integrated on VF610
   - "fsl,imx8qm-ftm-pwm" for PWM compatible with the one integrated on i.MX8QM
 - reg: Physical base address and length of the controller's registers
-- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of
   the cells format.
 - clock-names: Should include the following module clock source entries:
     "ftm_sys" (module clock, also can be used as counter clock),
diff --git a/Documentation/devicetree/bindings/pwm/pwm-hibvt.txt b/Documentation/devicetree/bindings/pwm/pwm-hibvt.txt
index daedfef09bb6..54dbc2a0e648 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-hibvt.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-hibvt.txt
@@ -10,7 +10,7 @@ Required properties:
 - reg: physical base address and length of the controller's registers.
 - clocks: phandle and clock specifier of the PWM reference clock.
 - resets: phandle and reset specifier for the PWM controller reset.
-- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of
   the cells format.
 
 Example:
diff --git a/Documentation/devicetree/bindings/pwm/pwm-lp3943.txt b/Documentation/devicetree/bindings/pwm/pwm-lp3943.txt
index 7bd9d3b12ce1..f214305a8f5e 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-lp3943.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-lp3943.txt
@@ -2,7 +2,7 @@ TI/National Semiconductor LP3943 PWM controller
 
 Required properties:
   - compatible: "ti,lp3943-pwm"
-  - #pwm-cells: Should be 2. See pwm.txt in this directory for a
+  - #pwm-cells: Should be 2. See pwm.yaml in this directory for a
                 description of the cells format.
                 Note that this hardware limits the period length to the
                 range 6250~1600000.
diff --git a/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt b/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt
index c8501530173c..69cae11d80a6 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt
@@ -9,7 +9,7 @@ Required properties:
    - "mediatek,mt7629-pwm", "mediatek,mt7622-pwm": found on mt7629 SoC.
    - "mediatek,mt8516-pwm": found on mt8516 SoC.
  - reg: physical base address and length of the controller's registers.
- - #pwm-cells: must be 2. See pwm.txt in this directory for a description of
+ - #pwm-cells: must be 2. See pwm.yaml in this directory for a description of
    the cell format.
  - clocks: phandle and clock specifier of the PWM reference clock.
  - clock-names: must contain the following, except for MT7628 which
diff --git a/Documentation/devicetree/bindings/pwm/pwm-meson.txt b/Documentation/devicetree/bindings/pwm/pwm-meson.txt
index 891632354065..bd02b0a1496f 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-meson.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-meson.txt
@@ -10,7 +10,7 @@ Required properties:
                          or "amlogic,meson-g12a-ee-pwm"
                          or "amlogic,meson-g12a-ao-pwm-ab"
                          or "amlogic,meson-g12a-ao-pwm-cd"
-- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of
   the cells format.
 
 Optional properties:
diff --git a/Documentation/devicetree/bindings/pwm/pwm-mtk-disp.txt b/Documentation/devicetree/bindings/pwm/pwm-mtk-disp.txt
index 6f8af2bcc7b7..0521957c253f 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-mtk-disp.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-mtk-disp.txt
@@ -6,7 +6,7 @@ Required properties:
    - "mediatek,mt6595-disp-pwm": found on mt6595 SoC.
    - "mediatek,mt8173-disp-pwm": found on mt8173 SoC.
  - reg: physical base address and length of the controller's registers.
- - #pwm-cells: must be 2. See pwm.txt in this directory for a description of
+ - #pwm-cells: must be 2. See pwm.yaml in this directory for a description of
    the cell format.
  - clocks: phandle and clock specifier of the PWM reference clock.
  - clock-names: must contain the following:
diff --git a/Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt b/Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt
index 5ccfcc82da08..d722ae3be363 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt
@@ -4,7 +4,7 @@ Required properties:
 - compatible: Shall contain "ti,omap-dmtimer-pwm".
 - ti,timers: phandle to PWM capable OMAP timer. See timer/ti,timer.txt for info
   about these timers.
-- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of
   the cells format.
 
 Optional properties:
diff --git a/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt b/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt
index 2c5e52a5bede..f70956dea77b 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt
@@ -14,7 +14,7 @@ Required properties:
    - For newer hardware (rk3328 and future socs): specified by name
      - "pwm": This is used to derive the functional clock.
      - "pclk": This is the APB bus clock.
- - #pwm-cells: must be 2 (rk2928) or 3 (rk3288). See pwm.txt in this directory
+ - #pwm-cells: must be 2 (rk2928) or 3 (rk3288). See pwm.yaml in this directory
    for a description of the cell format.
 
 Example:
diff --git a/Documentation/devicetree/bindings/pwm/pwm-sifive.txt b/Documentation/devicetree/bindings/pwm/pwm-sifive.txt
index 36447e3c9378..3d1dd7b06efc 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-sifive.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-sifive.txt
@@ -17,7 +17,7 @@ Required properties:
   Please refer to sifive-blocks-ip-versioning.txt for details.
 - reg: physical base address and length of the controller's registers
 - clocks: Should contain a clock identifier for the PWM's parent clock.
-- #pwm-cells: Should be 3. See pwm.txt in this directory
+- #pwm-cells: Should be 3. See pwm.yaml in this directory
   for a description of the cell format.
 - interrupts: one interrupt per PWM channel
 
diff --git a/Documentation/devicetree/bindings/pwm/pwm-sprd.txt b/Documentation/devicetree/bindings/pwm/pwm-sprd.txt
index 16fa5a096206..83a8b732418c 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-sprd.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-sprd.txt
@@ -9,8 +9,8 @@ Required properties:
 - clock-names: Should contain following entries:
   "pwmn": used to derive the functional clock for PWM channel n (n range: 0 ~ 3).
   "enablen": for PWM channel n enable clock (n range: 0 ~ 3).
-- #pwm-cells: Should be 2. See pwm.txt in this directory for a description of
-  the cells format.
+- #pwm-cells: Should be 2. See pwm-consumers.yaml in this directory
+  for a description of the cells format.
 
 Optional properties:
 - assigned-clocks: Reference to the PWM clock entries.
diff --git a/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt b/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt
index 6521bc44a74e..4cecb8e456b6 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt
@@ -8,7 +8,7 @@ See ../mfd/stm32-lptimer.txt for details about the parent node.
 Required parameters:
 - compatible:		Must be "st,stm32-pwm-lp".
 - #pwm-cells:		Should be set to 3. This PWM chip uses the default 3 cells
-			bindings defined in pwm.txt.
+			bindings defined in pwm.yaml.
 
 Optional properties:
 - pinctrl-names: 	Set to "default". An additional "sleep" state can be
diff --git a/Documentation/devicetree/bindings/pwm/pwm-stm32.txt b/Documentation/devicetree/bindings/pwm/pwm-stm32.txt
index a8690bfa5e1f..f390a5ba3d3a 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-stm32.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-stm32.txt
@@ -9,7 +9,7 @@ Required parameters:
 - pinctrl-0: 		List of phandles pointing to pin configuration nodes for PWM module.
 			For Pinctrl properties see ../pinctrl/pinctrl-bindings.txt
 - #pwm-cells:		Should be set to 3. This PWM chip uses the default 3 cells
-			bindings defined in pwm.txt.
+			bindings defined in pwm.yaml.
 
 Optional parameters:
 - st,breakinput:	One or two <index level filter> to describe break input configurations.
diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
index b9a1d7402128..c7c4347a769a 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
@@ -8,7 +8,7 @@ Required properties:
   for dra746 - compatible = "ti,dra746-ecap", "ti,am3352-ecap";
   for 66ak2g - compatible = "ti,k2g-ecap", "ti,am3352-ecap";
   for am654  - compatible = "ti,am654-ecap", "ti,am3352-ecap";
-- #pwm-cells: should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 3. See pwm.yaml in this directory for a description of
   the cells format. The PWM channel index ranges from 0 to 4. The only third
   cell flag supported by this binding is PWM_POLARITY_INVERTED.
 - reg: physical base address and size of the registers map.
diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt
index 31c4577157dd..c7e28f6d28be 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt
@@ -7,7 +7,7 @@ Required properties:
   for am654   - compatible = "ti,am654-ehrpwm", "ti-am3352-ehrpwm";
   for da850   - compatible = "ti,da850-ehrpwm", "ti-am3352-ehrpwm", "ti,am33xx-ehrpwm";
   for dra746 - compatible = "ti,dra746-ehrpwm", "ti-am3352-ehrpwm";
-- #pwm-cells: should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 3. See pwm.yaml in this directory for a description of
   the cells format. The only third cell flag supported by this binding is
   PWM_POLARITY_INVERTED.
 - reg: physical base address and size of the registers map.
diff --git a/Documentation/devicetree/bindings/pwm/pwm-zx.txt b/Documentation/devicetree/bindings/pwm/pwm-zx.txt
index a6bcc75c9164..3c8fe7aa8269 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-zx.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-zx.txt
@@ -7,7 +7,7 @@ Required properties:
  - clock-names: "pclk" for PCLK, "wclk" for WCLK to the PWM controller.  The
    PCLK is for register access, while WCLK is the reference clock for
    calculating period and duty cycles.
- - #pwm-cells: Should be 3. See pwm.txt in this directory for a description of
+ - #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of
    the cells format.
 
 Example:
diff --git a/Documentation/devicetree/bindings/pwm/pwm.txt b/Documentation/devicetree/bindings/pwm/pwm.txt
deleted file mode 100644
index 8556263b8502..000000000000
--- a/Documentation/devicetree/bindings/pwm/pwm.txt
+++ /dev/null
@@ -1,69 +0,0 @@
-Specifying PWM information for devices
-======================================
-
-1) PWM user nodes
------------------
-
-PWM users should specify a list of PWM devices that they want to use
-with a property containing a 'pwm-list':
-
-	pwm-list ::= <single-pwm> [pwm-list]
-	single-pwm ::= <pwm-phandle> <pwm-specifier>
-	pwm-phandle : phandle to PWM controller node
-	pwm-specifier : array of #pwm-cells specifying the given PWM
-			(controller specific)
-
-PWM properties should be named "pwms". The exact meaning of each pwms
-property must be documented in the device tree binding for each device.
-An optional property "pwm-names" may contain a list of strings to label
-each of the PWM devices listed in the "pwms" property. If no "pwm-names"
-property is given, the name of the user node will be used as fallback.
-
-Drivers for devices that use more than a single PWM device can use the
-"pwm-names" property to map the name of the PWM device requested by the
-pwm_get() call to an index into the list given by the "pwms" property.
-
-The following example could be used to describe a PWM-based backlight
-device:
-
-	pwm: pwm {
-		#pwm-cells = <2>;
-	};
-
-	[...]
-
-	bl: backlight {
-		pwms = <&pwm 0 5000000>;
-		pwm-names = "backlight";
-	};
-
-Note that in the example above, specifying the "pwm-names" is redundant
-because the name "backlight" would be used as fallback anyway.
-
-pwm-specifier typically encodes the chip-relative PWM number and the PWM
-period in nanoseconds.
-
-Optionally, the pwm-specifier can encode a number of flags (defined in
-<dt-bindings/pwm/pwm.h>) in a third cell:
-- PWM_POLARITY_INVERTED: invert the PWM signal polarity
-
-Example with optional PWM specifier for inverse polarity
-
-	bl: backlight {
-		pwms = <&pwm 0 5000000 PWM_POLARITY_INVERTED>;
-		pwm-names = "backlight";
-	};
-
-2) PWM controller nodes
------------------------
-
-PWM controller nodes must specify the number of cells used for the
-specifier using the '#pwm-cells' property.
-
-An example PWM controller might look like this:
-
-	pwm: pwm@7000a000 {
-		compatible = "nvidia,tegra20-pwm";
-		reg = <0x7000a000 0x100>;
-		#pwm-cells = <2>;
-	};
diff --git a/Documentation/devicetree/bindings/pwm/pwm.yaml b/Documentation/devicetree/bindings/pwm/pwm.yaml
new file mode 100644
index 000000000000..aad99d505bb0
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/pwm.yaml
@@ -0,0 +1,29 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pwm/pwm.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: PWM controllers (providers)
+
+maintainers:
+  - Thierry Reding <thierry.reding@gmail.com>
+
+properties:
+  $nodename:
+    pattern: "^pwm(@.*|-[0-9a-f])*$"
+
+  "#pwm-cells":
+    description:
+      Number of cells in a PWM specifier.
+
+required:
+  - "#pwm-cells"
+
+examples:
+  - |
+    pwm: pwm@7000a000 {
+      compatible = "nvidia,tegra20-pwm";
+      reg = <0x7000a000 0x100>;
+      #pwm-cells = <2>;
+    };
diff --git a/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt b/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt
index fbd6a4f943ce..a29137869f7a 100644
--- a/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt
+++ b/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt
@@ -20,7 +20,7 @@ Required Properties:
  - "renesas,pwm-r8a77990": for R-Car E3
  - "renesas,pwm-r8a77995": for R-Car D3
 - reg: base address and length of the registers block for the PWM.
-- #pwm-cells: should be 2. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 2. See pwm.yaml in this directory for a description of
   the cells format.
 - clocks: clock phandle and specifier pair.
 - pinctrl-0: phandle, referring to a default pin configuration node.
diff --git a/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt b/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt
index 848a92b53d81..966994968069 100644
--- a/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt
@@ -19,11 +19,11 @@ Required Properties:
   - reg: Base address and length of each memory resource used by the PWM
     controller hardware module.
 
-  - #pwm-cells: should be 3. See pwm.txt in this directory for a description of
+  - #pwm-cells: should be 3. See pwm.yaml in this directory for a description of
     the cells format. The only third cell flag supported by this binding is
     PWM_POLARITY_INVERTED.
 
-Please refer to pwm.txt in this directory for details of the common PWM bindings
+Please refer to pwm-consumers.yaml in this directory for details of the common PWM bindings
 used by client devices.
 
 Example: R8A7740 (R-Mobile A1) TPU controller node
diff --git a/Documentation/devicetree/bindings/pwm/spear-pwm.txt b/Documentation/devicetree/bindings/pwm/spear-pwm.txt
index b486de2c3fe3..95894128b62f 100644
--- a/Documentation/devicetree/bindings/pwm/spear-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/spear-pwm.txt
@@ -5,7 +5,7 @@ Required properties:
   - "st,spear320-pwm"
   - "st,spear1340-pwm"
 - reg: physical base address and length of the controller's registers
-- #pwm-cells: should be 2. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 2. See pwm.yaml in this directory for a description of
   the cells format.
 
 Example:
diff --git a/Documentation/devicetree/bindings/pwm/st,stmpe-pwm.txt b/Documentation/devicetree/bindings/pwm/st,stmpe-pwm.txt
index cb209646bf13..f401316e0248 100644
--- a/Documentation/devicetree/bindings/pwm/st,stmpe-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/st,stmpe-pwm.txt
@@ -7,7 +7,7 @@ subdevices of the STMPE MFD device.
 Required properties:
 - compatible: should be:
   - "st,stmpe-pwm"
-- #pwm-cells: should be 2. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 2. See pwm.yaml in this directory for a description of
   the cells format.
 
 Example:
diff --git a/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt b/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt
index 4e32bee11201..d97ca1964e94 100644
--- a/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt
@@ -6,7 +6,7 @@ On TWL6030 series: PWM0 and PWM1
 
 Required properties:
 - compatible: "ti,twl4030-pwm" or "ti,twl6030-pwm"
-- #pwm-cells: should be 2. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 2. See pwm.yaml in this directory for a description of
   the cells format.
 
 Example:
diff --git a/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt b/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt
index 9f4b46090782..31ca1b032ef0 100644
--- a/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt
+++ b/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt
@@ -6,7 +6,7 @@ On TWL6030 series: LED PWM (mainly used as charging indicator LED)
 
 Required properties:
 - compatible: "ti,twl4030-pwmled" or "ti,twl6030-pwmled"
-- #pwm-cells: should be 2. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 2. See pwm.yaml in this directory for a description of
   the cells format.
 
 Example:
diff --git a/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt b/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt
index a76390e6df2e..4fba93ce1985 100644
--- a/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt
@@ -3,7 +3,7 @@ VIA/Wondermedia VT8500/WM8xxx series SoC PWM controller
 Required properties:
 - compatible: should be "via,vt8500-pwm"
 - reg: physical base address and length of the controller's registers
-- #pwm-cells: should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 3. See pwm.yaml in this directory for a description of
   the cells format. The only third cell flag supported by this binding is
   PWM_POLARITY_INVERTED.
 - clocks: phandle to the PWM source clock
diff --git a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt
index 3d78d507e29f..252edcc2e381 100644
--- a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt
@@ -27,7 +27,7 @@ Required properties:
 --------------------
 - compatible:		Should be "pwm-regulator"
 
-- pwms:			PWM specification (See: ../pwm/pwm.txt)
+- pwms:			PWM specification (See: ../pwm/pwm-consumers.yaml)
 
 Only required for Voltage Table Mode:
 - voltage-table: 	Voltage and Duty-Cycle table consisting of 2 cells
diff --git a/Documentation/devicetree/bindings/timer/ingenic,tcu.txt b/Documentation/devicetree/bindings/timer/ingenic,tcu.txt
index 5a4b9ddd9470..0c7bd51c19eb 100644
--- a/Documentation/devicetree/bindings/timer/ingenic,tcu.txt
+++ b/Documentation/devicetree/bindings/timer/ingenic,tcu.txt
@@ -42,7 +42,7 @@ Required properties:
 - compatible: Must be one of:
   * ingenic,jz4740-pwm
   * ingenic,jz4725b-pwm
-- #pwm-cells: Should be 3. See ../pwm/pwm.txt for a description of the cell
+- #pwm-cells: Should be 3. See ../pwm/pwm.yaml for a description of the cell
   format.
 - clocks: List of phandle & clock specifiers for the TCU clocks.
 - clock-names: List of name strings for the TCU clocks.
-- 
2.17.1


^ permalink raw reply related	[flat|nested] 5+ messages in thread

* [PATCH v3 2/2] dt-bindings: pwm: Convert Samsung PWM bindings to json-schema
  2019-10-02 16:40 [PATCH v3 1/2] dt-bindings: pwm: Convert PWM bindings to json-schema Krzysztof Kozlowski
@ 2019-10-02 16:40 ` Krzysztof Kozlowski
  2019-10-10 18:58   ` Rob Herring
  2019-10-08 23:46 ` [PATCH v3 1/2] dt-bindings: pwm: Convert " Paul Walmsley
  2019-10-10 18:54 ` Rob Herring
  2 siblings, 1 reply; 5+ messages in thread
From: Krzysztof Kozlowski @ 2019-10-02 16:40 UTC (permalink / raw)
  To: Rob Herring, Mark Rutland, Thierry Reding, Uwe Kleine-König,
	linux-clk, devicetree, linux-kernel, dri-devel, linux-leds,
	linux-pwm, linux-arm-kernel, linux-tegra,
	bcm-kernel-feedback-list, linux-rpi-kernel, linux-amlogic,
	linux-mediatek, linux-rockchip, linux-riscv, linux-stm32
  Cc: Krzysztof Kozlowski

Convert Samsung PWM (S3C, S5P and Exynos SoCs) bindings to DT schema
format using json-schema.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

---

Changes since v2:
1. Add additionalProperties: false.

Changes since v1:
1. Indent example with four spaces (more readable),
2. Fix samsung,pwm-outputs after review,
3. Remove double-quotes from clock names.
---
 .../devicetree/bindings/pwm/pwm-samsung.txt   |  51 --------
 .../devicetree/bindings/pwm/pwm-samsung.yaml  | 109 ++++++++++++++++++
 2 files changed, 109 insertions(+), 51 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/pwm/pwm-samsung.txt
 create mode 100644 Documentation/devicetree/bindings/pwm/pwm-samsung.yaml

diff --git a/Documentation/devicetree/bindings/pwm/pwm-samsung.txt b/Documentation/devicetree/bindings/pwm/pwm-samsung.txt
deleted file mode 100644
index 5538de9c2007..000000000000
--- a/Documentation/devicetree/bindings/pwm/pwm-samsung.txt
+++ /dev/null
@@ -1,51 +0,0 @@
-* Samsung PWM timers
-
-Samsung SoCs contain PWM timer blocks which can be used for system clock source
-and clock event timers, as well as to drive SoC outputs with PWM signal. Each
-PWM timer block provides 5 PWM channels (not all of them can drive physical
-outputs - see SoC and board manual).
-
-Be aware that the clocksource driver supports only uniprocessor systems.
-
-Required properties:
-- compatible : should be one of following:
-    samsung,s3c2410-pwm - for 16-bit timers present on S3C24xx SoCs
-    samsung,s3c6400-pwm - for 32-bit timers present on S3C64xx SoCs
-    samsung,s5p6440-pwm - for 32-bit timers present on S5P64x0 SoCs
-    samsung,s5pc100-pwm - for 32-bit timers present on S5PC100, S5PV210,
-			  Exynos4210 rev0 SoCs
-    samsung,exynos4210-pwm - for 32-bit timers present on Exynos4210,
-                          Exynos4x12, Exynos5250 and Exynos5420 SoCs
-- reg: base address and size of register area
-- interrupts: list of timer interrupts (one interrupt per timer, starting at
-  timer 0)
-- clock-names: should contain all following required clock names:
-    - "timers" - PWM base clock used to generate PWM signals,
-  and any subset of following optional clock names:
-    - "pwm-tclk0" - first external PWM clock source,
-    - "pwm-tclk1" - second external PWM clock source.
-  Note that not all IP variants allow using all external clock sources.
-  Refer to SoC documentation to learn which clock source configurations
-  are available.
-- clocks: should contain clock specifiers of all clocks, which input names
-  have been specified in clock-names property, in same order.
-- #pwm-cells: should be 3. See pwm.txt in this directory for a description of
-  the cells format. The only third cell flag supported by this binding is
-  PWM_POLARITY_INVERTED.
-
-Optional properties:
-- samsung,pwm-outputs: list of PWM channels used as PWM outputs on particular
-    platform - an array of up to 5 elements being indices of PWM channels
-    (from 0 to 4), the order does not matter.
-
-Example:
-	pwm@7f006000 {
-		compatible = "samsung,s3c6400-pwm";
-		reg = <0x7f006000 0x1000>;
-		interrupt-parent = <&vic0>;
-		interrupts = <23>, <24>, <25>, <27>, <28>;
-		clocks = <&clock 67>;
-		clock-names = "timers";
-		samsung,pwm-outputs = <0>, <1>;
-		#pwm-cells = <3>;
-	}
diff --git a/Documentation/devicetree/bindings/pwm/pwm-samsung.yaml b/Documentation/devicetree/bindings/pwm/pwm-samsung.yaml
new file mode 100644
index 000000000000..ea7f32905172
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/pwm-samsung.yaml
@@ -0,0 +1,109 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pwm/pwm-samsung.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung SoC PWM timers
+
+maintainers:
+  - Thierry Reding <thierry.reding@gmail.com>
+  - Krzysztof Kozlowski <krzk@kernel.org>
+
+description: |+
+  Samsung SoCs contain PWM timer blocks which can be used for system clock source
+  and clock event timers, as well as to drive SoC outputs with PWM signal. Each
+  PWM timer block provides 5 PWM channels (not all of them can drive physical
+  outputs - see SoC and board manual).
+
+  Be aware that the clocksource driver supports only uniprocessor systems.
+
+allOf:
+  - $ref: pwm.yaml#
+
+properties:
+  compatible:
+    enum:
+      - samsung,s3c2410-pwm             # 16-bit, S3C24xx
+      - samsung,s3c6400-pwm             # 32-bit, S3C64xx
+      - samsung,s5p6440-pwm             # 32-bit, S5P64x0
+      - samsung,s5pc100-pwm             # 32-bit, S5PC100, S5PV210, Exynos4210 rev0 SoCs
+      - samsung,exynos4210-pwm          # 32-bit, Exynos
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    minItems: 1
+    maxItems: 3
+
+  clock-names:
+    description: |
+      Should contain all following required clock names:
+      - "timers" - PWM base clock used to generate PWM signals,
+      and any subset of following optional clock names:
+      - "pwm-tclk0" - first external PWM clock source,
+      - "pwm-tclk1" - second external PWM clock source.
+      Note that not all IP variants allow using all external clock sources.
+      Refer to SoC documentation to learn which clock source configurations
+      are available.
+    oneOf:
+      - items:
+        - const: timers
+      - items:
+        - const: timers
+        - const: pwm-tclk0
+      - items:
+        - const: timers
+        - const: pwm-tclk1
+      - items:
+        - const: timers
+        - const: pwm-tclk0
+        - const: pwm-tclk1
+
+  interrupts:
+    description:
+      One interrupt per timer, starting at timer 0.
+    minItems: 1
+    maxItems: 5
+
+  "#pwm-cells":
+    description:
+      The only third cell flag supported by this binding
+      is PWM_POLARITY_INVERTED.
+    const: 3
+
+  samsung,pwm-outputs:
+    description:
+      A list of PWM channels used as PWM outputs on particular platform.
+      It is an array of up to 5 elements being indices of PWM channels
+      (from 0 to 4), the order does not matter.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32-array
+      - uniqueItems: true
+      - items:
+          minimum: 0
+          maximum: 4
+
+required:
+  - clocks
+  - clock-names
+  - compatible
+  - interrupts
+  - "#pwm-cells"
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    pwm@7f006000 {
+        compatible = "samsung,s3c6400-pwm";
+        reg = <0x7f006000 0x1000>;
+        interrupt-parent = <&vic0>;
+        interrupts = <23>, <24>, <25>, <27>, <28>;
+        clocks = <&clock 67>;
+        clock-names = "timers";
+        samsung,pwm-outputs = <0>, <1>;
+        #pwm-cells = <3>;
+    };
-- 
2.17.1


^ permalink raw reply related	[flat|nested] 5+ messages in thread

* Re: [PATCH v3 1/2] dt-bindings: pwm: Convert PWM bindings to json-schema
  2019-10-02 16:40 [PATCH v3 1/2] dt-bindings: pwm: Convert PWM bindings to json-schema Krzysztof Kozlowski
  2019-10-02 16:40 ` [PATCH v3 2/2] dt-bindings: pwm: Convert Samsung " Krzysztof Kozlowski
@ 2019-10-08 23:46 ` Paul Walmsley
  2019-10-10 18:54 ` Rob Herring
  2 siblings, 0 replies; 5+ messages in thread
From: Paul Walmsley @ 2019-10-08 23:46 UTC (permalink / raw)
  To: Krzysztof Kozlowski
  Cc: Rob Herring, Mark Rutland, Thierry Reding, Uwe Kleine-König,
	linux-clk, devicetree, linux-kernel, dri-devel, linux-leds,
	linux-pwm, linux-arm-kernel, linux-tegra,
	bcm-kernel-feedback-list, linux-rpi-kernel, linux-amlogic,
	linux-mediatek, linux-rockchip, linux-riscv, linux-stm32

On Wed, 2 Oct 2019, Krzysztof Kozlowski wrote:

> Convert generic PWM bindings to DT schema format using json-schema.  The
> consumer bindings are split to separate file.
> 
> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
> 
> ---
> 

[ ... ]

> diff --git a/Documentation/devicetree/bindings/pwm/pwm-sifive.txt b/Documentation/devicetree/bindings/pwm/pwm-sifive.txt
> index 36447e3c9378..3d1dd7b06efc 100644
> --- a/Documentation/devicetree/bindings/pwm/pwm-sifive.txt
> +++ b/Documentation/devicetree/bindings/pwm/pwm-sifive.txt
> @@ -17,7 +17,7 @@ Required properties:
>    Please refer to sifive-blocks-ip-versioning.txt for details.
>  - reg: physical base address and length of the controller's registers
>  - clocks: Should contain a clock identifier for the PWM's parent clock.
> -- #pwm-cells: Should be 3. See pwm.txt in this directory
> +- #pwm-cells: Should be 3. See pwm.yaml in this directory
>    for a description of the cell format.
>  - interrupts: one interrupt per PWM channel

For the SiFive PWM driver documentation:

Acked-by: Paul Walmsley <paul.walmsley@sifive.com>


- Paul

^ permalink raw reply	[flat|nested] 5+ messages in thread

* Re: [PATCH v3 1/2] dt-bindings: pwm: Convert PWM bindings to json-schema
  2019-10-02 16:40 [PATCH v3 1/2] dt-bindings: pwm: Convert PWM bindings to json-schema Krzysztof Kozlowski
  2019-10-02 16:40 ` [PATCH v3 2/2] dt-bindings: pwm: Convert Samsung " Krzysztof Kozlowski
  2019-10-08 23:46 ` [PATCH v3 1/2] dt-bindings: pwm: Convert " Paul Walmsley
@ 2019-10-10 18:54 ` Rob Herring
  2 siblings, 0 replies; 5+ messages in thread
From: Rob Herring @ 2019-10-10 18:54 UTC (permalink / raw)
  To: Krzysztof Kozlowski
  Cc: Mark Rutland, Thierry Reding, Uwe Kleine-König, linux-clk,
	devicetree, linux-kernel, dri-devel, linux-leds, linux-pwm,
	linux-arm-kernel, linux-tegra, bcm-kernel-feedback-list,
	linux-rpi-kernel, linux-amlogic, linux-mediatek, linux-rockchip,
	linux-riscv, linux-stm32

On Wed, Oct 02, 2019 at 06:40:46PM +0200, Krzysztof Kozlowski wrote:
> Convert generic PWM bindings to DT schema format using json-schema.  The
> consumer bindings are split to separate file.
> 
> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
> 
> ---
> 
> Changes since v2:
> 1. Change also pwm-sprd.txt
> 
> Changes since v1:
> 1. Indent example with four spaces (more readable),
> 2. Change pattern for pwm nodes,
> 3. Remove $ref from #cells.
> ---


> diff --git a/Documentation/devicetree/bindings/pwm/pwm-consumers.yaml b/Documentation/devicetree/bindings/pwm/pwm-consumers.yaml
> new file mode 100644
> index 000000000000..39c844fe6338
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pwm/pwm-consumers.yaml
> @@ -0,0 +1,76 @@
> +# SPDX-License-Identifier: GPL-2.0
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pwm/pwm-consumers.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Specifying PWM information for devices
> +
> +maintainers:
> +  - Thierry Reding <thierry.reding@gmail.com>
> +
> +description: |
> +  PWM properties should be named "pwms". The exact meaning of each pwms
> +  property must be documented in the device tree binding for each device.
> +  An optional property "pwm-names" may contain a list of strings to label
> +  each of the PWM devices listed in the "pwms" property. If no "pwm-names"
> +  property is given, the name of the user node will be used as fallback.
> +
> +  Drivers for devices that use more than a single PWM device can use the
> +  "pwm-names" property to map the name of the PWM device requested by the
> +  pwm_get() call to an index into the list given by the "pwms" property.
> +
> +properties:
> +  pwms:
> +    $ref: /schemas/types.yaml#/definitions/phandle-array
> +    description: |
> +      Phandle to PWM controller node and pwm-specifier (controller specific).
> +      pwm-specifier typically encodes the chip-relative PWM number and the PWM
> +      period in nanoseconds.
> +      Optionally, the pwm-specifier can encode a number of flags (defined in
> +      <dt-bindings/pwm/pwm.h>) in a third cell:
> +        - PWM_POLARITY_INVERTED: invert the PWM signal polarity
> +
> +  pwm-names:
> +    $ref: /schemas/types.yaml#/definitions/string-array
> +    description:
> +      A list of strings to label each of the PWM devices listed in the "pwms"
> +      property. If no "pwm-names" property is given, the name of the user node
> +      will be used as fallback.
> +
> +required:
> +  - pwms

This schema is never applied because it has no 'select' which is only 
automatic for $nodename or compatible. You could include this from other 
schemas, but why? Any consumer still has to list these properties to 
define their specific constraints.

We already have a schema in dtschema for consumer side. It's just 
missing descriptions which needs relicensing from this.

> +
> +dependencies:
> +  pwm-names: [ pwms ]

^ permalink raw reply	[flat|nested] 5+ messages in thread

* Re: [PATCH v3 2/2] dt-bindings: pwm: Convert Samsung PWM bindings to json-schema
  2019-10-02 16:40 ` [PATCH v3 2/2] dt-bindings: pwm: Convert Samsung " Krzysztof Kozlowski
@ 2019-10-10 18:58   ` Rob Herring
  0 siblings, 0 replies; 5+ messages in thread
From: Rob Herring @ 2019-10-10 18:58 UTC (permalink / raw)
  To: Krzysztof Kozlowski
  Cc: Mark Rutland, Thierry Reding, Uwe Kleine-König, linux-clk,
	devicetree, linux-kernel, dri-devel, Linux LED Subsystem,
	Linux PWM List,
	moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE,
	linux-tegra, maintainer:BROADCOM BCM7XXX ARM ARCHITECTURE,
	moderated list:BROADCOM BCM2835 ARM ARCHITECTURE, linux-amlogic,
	moderated list:ARM/Mediatek SoC support,
	open list:ARM/Rockchip SoC...,
	linux-riscv, linux-stm32

On Wed, Oct 2, 2019 at 11:41 AM Krzysztof Kozlowski <krzk@kernel.org> wrote:
>
> Convert Samsung PWM (S3C, S5P and Exynos SoCs) bindings to DT schema
> format using json-schema.
>
> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
>
> ---
>
> Changes since v2:
> 1. Add additionalProperties: false.
>
> Changes since v1:
> 1. Indent example with four spaces (more readable),
> 2. Fix samsung,pwm-outputs after review,
> 3. Remove double-quotes from clock names.
> ---
>  .../devicetree/bindings/pwm/pwm-samsung.txt   |  51 --------
>  .../devicetree/bindings/pwm/pwm-samsung.yaml  | 109 ++++++++++++++++++
>  2 files changed, 109 insertions(+), 51 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/pwm/pwm-samsung.txt
>  create mode 100644 Documentation/devicetree/bindings/pwm/pwm-samsung.yaml

Reviewed-by: Rob Herring <robh@kernel.org>

^ permalink raw reply	[flat|nested] 5+ messages in thread

end of thread, other threads:[~2019-10-10 18:58 UTC | newest]

Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-10-02 16:40 [PATCH v3 1/2] dt-bindings: pwm: Convert PWM bindings to json-schema Krzysztof Kozlowski
2019-10-02 16:40 ` [PATCH v3 2/2] dt-bindings: pwm: Convert Samsung " Krzysztof Kozlowski
2019-10-10 18:58   ` Rob Herring
2019-10-08 23:46 ` [PATCH v3 1/2] dt-bindings: pwm: Convert " Paul Walmsley
2019-10-10 18:54 ` Rob Herring

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).