linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Ludovic Desroches <ludovic.desroches@microchip.com>
To: Kamel Bouhara <kamel.bouhara@bootlin.com>
Cc: Wolfram Sang <wsa@the-dreams.de>, <linux-i2c@vger.kernel.org>,
	<linux-kernel@vger.kernel.org>,
	Nicolas Ferre <nicolas.ferre@microchip.com>,
	Alexandre Belloni <alexandre.belloni@bootlin.com>,
	<linux-arm-kernel@lists.infradead.org>,
	<devicetree@vger.kernel.org>,
	"Thomas Petazzoni" <thomas.petazzoni@bootlin.com>
Subject: Re: [PATCH 2/4] i2c: at91: implement i2c bus recovery
Date: Wed, 9 Oct 2019 15:55:00 +0200	[thread overview]
Message-ID: <20191009135500.ufkxcemccwfcfys7@M43218.corp.atmel.com> (raw)
In-Reply-To: <20191002144658.7718-3-kamel.bouhara@bootlin.com>

On Wed, Oct 02, 2019 at 04:46:56PM +0200, Kamel Bouhara wrote:
> External E-Mail
> 
> 
> Implement i2c bus recovery when slaves devices might hold SDA low.
> In this case re-assign SCL/SDA to gpios and issue 9 dummy clock pulses
> until the slave release SDA.
> 

Hi Kamel,

Thanks for adding this new feature. As I see patches only for sama5d3 and
sama5d4, I assume it has not been tested with a sama5d2, isn't it?

I doubt it works with a sama5d2 because of the pinctrl. I also wonder if it can
work if we add .strict = true to pinmux_ops which is something plan for the
future...

Are you able to test these points? It would be nice to be aware of
possible side effects.

Regards

Ludovic

> Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
> ---
>  drivers/i2c/busses/i2c-at91-master.c | 63 ++++++++++++++++++++++++++++
>  drivers/i2c/busses/i2c-at91.h        |  8 ++++
>  2 files changed, 71 insertions(+)
> 
> diff --git a/drivers/i2c/busses/i2c-at91-master.c b/drivers/i2c/busses/i2c-at91-master.c
> index a3fcc35ffd3b..df5bb93f952d 100644
> --- a/drivers/i2c/busses/i2c-at91-master.c
> +++ b/drivers/i2c/busses/i2c-at91-master.c
> @@ -18,11 +18,13 @@
>  #include <linux/dma-mapping.h>
>  #include <linux/dmaengine.h>
>  #include <linux/err.h>
> +#include <linux/gpio/consumer.h>
>  #include <linux/i2c.h>
>  #include <linux/interrupt.h>
>  #include <linux/io.h>
>  #include <linux/of.h>
>  #include <linux/of_device.h>
> +#include <linux/pinctrl/consumer.h>
>  #include <linux/platform_device.h>
>  #include <linux/platform_data/dma-atmel.h>
>  #include <linux/pm_runtime.h>
> @@ -768,6 +770,63 @@ static int at91_twi_configure_dma(struct at91_twi_dev *dev, u32 phy_addr)
>  	return ret;
>  }
>  
> +static void at91_prepare_twi_recovery(struct i2c_adapter *adap)
> +{
> +	struct at91_twi_dev *dev = i2c_get_adapdata(adap);
> +
> +	pinctrl_select_state(dev->pinctrl, dev->pinctrl_pins_gpio);
> +}
> +
> +static void at91_unprepare_twi_recovery(struct i2c_adapter *adap)
> +{
> +	struct at91_twi_dev *dev = i2c_get_adapdata(adap);
> +
> +	pinctrl_select_state(dev->pinctrl, dev->pinctrl_pins_default);
> +}
> +
> +static int at91_init_twi_recovery_info(struct platform_device *pdev,
> +				       struct at91_twi_dev *dev)
> +{
> +	struct i2c_bus_recovery_info *rinfo = &dev->rinfo;
> +
> +	dev->pinctrl = devm_pinctrl_get(&pdev->dev);
> +	if (!dev->pinctrl || IS_ERR(dev->pinctrl)) {
> +		dev_info(dev->dev, "can't get pinctrl, bus recovery not supported\n");
> +		return PTR_ERR(dev->pinctrl);
> +	}
> +
> +	dev->pinctrl_pins_default = pinctrl_lookup_state(dev->pinctrl,
> +							 PINCTRL_STATE_DEFAULT);
> +	dev->pinctrl_pins_gpio = pinctrl_lookup_state(dev->pinctrl,
> +						      "gpio");
> +	rinfo->sda_gpiod = devm_gpiod_get(&pdev->dev, "sda", GPIOD_IN);
> +	if (PTR_ERR(rinfo->sda_gpiod) == -EPROBE_DEFER)
> +		return -EPROBE_DEFER;
> +
> +	rinfo->scl_gpiod = devm_gpiod_get(&pdev->dev, "scl",
> +					  GPIOD_OUT_HIGH_OPEN_DRAIN);
> +	if (PTR_ERR(rinfo->scl_gpiod) == -EPROBE_DEFER)
> +		return -EPROBE_DEFER;
> +
> +	if (IS_ERR(rinfo->sda_gpiod) ||
> +		   IS_ERR(rinfo->scl_gpiod) ||
> +		   IS_ERR(dev->pinctrl_pins_default) ||
> +		   IS_ERR(dev->pinctrl_pins_gpio)) {
> +		dev_info(&pdev->dev, "recovery information incomplete\n");
> +		return -EINVAL;
> +	}
> +
> +	dev_info(&pdev->dev, "using scl%s for recovery\n",
> +		 rinfo->sda_gpiod ? ",sda" : "");
> +
> +	rinfo->prepare_recovery = at91_prepare_twi_recovery;
> +	rinfo->unprepare_recovery = at91_unprepare_twi_recovery;
> +	rinfo->recover_bus = i2c_generic_scl_recovery;
> +	dev->adapter.bus_recovery_info = rinfo;
> +
> +	return 0;
> +}
> +
>  int at91_twi_probe_master(struct platform_device *pdev,
>  			  u32 phy_addr, struct at91_twi_dev *dev)
>  {
> @@ -795,6 +854,10 @@ int at91_twi_probe_master(struct platform_device *pdev,
>  
>  	at91_calc_twi_clock(dev);
>  
> +	rc = at91_init_twi_recovery_info(pdev, dev);
> +	if (rc == -EPROBE_DEFER)
> +		return rc;
> +
>  	dev->adapter.algo = &at91_twi_algorithm;
>  	dev->adapter.quirks = &at91_twi_quirks;
>  
> diff --git a/drivers/i2c/busses/i2c-at91.h b/drivers/i2c/busses/i2c-at91.h
> index 499b506f6128..b89dab55e776 100644
> --- a/drivers/i2c/busses/i2c-at91.h
> +++ b/drivers/i2c/busses/i2c-at91.h
> @@ -141,6 +141,10 @@ struct at91_twi_dev {
>  	u32 fifo_size;
>  	struct at91_twi_dma dma;
>  	bool slave_detected;
> +	struct i2c_bus_recovery_info rinfo;
> +	struct pinctrl *pinctrl;
> +	struct pinctrl_state *pinctrl_pins_default;
> +	struct pinctrl_state *pinctrl_pins_gpio;
>  #ifdef CONFIG_I2C_AT91_SLAVE_EXPERIMENTAL
>  	unsigned smr;
>  	struct i2c_client *slave;
> @@ -158,6 +162,10 @@ void at91_init_twi_bus_master(struct at91_twi_dev *dev);
>  int at91_twi_probe_master(struct platform_device *pdev, u32 phy_addr,
>  			  struct at91_twi_dev *dev);
>  
> +void at91_twi_prepare_recovery(struct i2c_adapter *adap);
> +void at91_twi_unprepare_recovery(struct i2c_adapter *adap);
> +void at91_twi_init_recovery_info(struct at91_twi_dev *dev);
> +
>  #ifdef CONFIG_I2C_AT91_SLAVE_EXPERIMENTAL
>  void at91_init_twi_bus_slave(struct at91_twi_dev *dev);
>  int at91_twi_probe_slave(struct platform_device *pdev, u32 phy_addr,
> -- 
> 2.23.0
> 
> 

  parent reply	other threads:[~2019-10-09 13:54 UTC|newest]

Thread overview: 18+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-10-02 14:46 [PATCH 0/4] i2c bus recovery for Microchip SoCs Kamel Bouhara
2019-10-02 14:46 ` [PATCH 1/4] dt-bindings: i2c: at91: document optional bus recovery properties Kamel Bouhara
2019-10-02 14:46 ` [PATCH 2/4] i2c: at91: implement i2c bus recovery Kamel Bouhara
2019-10-04  9:35   ` Claudiu.Beznea
2019-10-04 20:39     ` Uwe Kleine-König
2019-10-07 10:17       ` Claudiu.Beznea
2019-10-09 13:55   ` Ludovic Desroches [this message]
2019-10-09 14:01     ` Alexandre Belloni
2019-10-10  6:54       ` Ludovic Desroches
2019-10-21 20:20   ` Wolfram Sang
     [not found]     ` <724d3470-0561-1b3f-c826-bc16c74a8c0a@bootlin.com>
2019-10-24 14:08       ` Codrin.Ciubotariu
2019-10-24 15:07         ` Wolfram Sang
2019-10-25  1:14           ` Phil Reid
2020-08-25 13:28             ` Wolfram Sang
2020-08-25 23:44               ` Phil Reid
2019-10-02 14:46 ` [PATCH 3/4] ARM: at91/dt: sama5d3: add i2c gpio pinctrl Kamel Bouhara
2019-10-02 14:46 ` [PATCH 4/4] ARM: at91/dt: sama5d4: " Kamel Bouhara
2019-10-15 19:10 ` [PATCH 0/4] i2c bus recovery for Microchip SoCs Rob Herring

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20191009135500.ufkxcemccwfcfys7@M43218.corp.atmel.com \
    --to=ludovic.desroches@microchip.com \
    --cc=alexandre.belloni@bootlin.com \
    --cc=devicetree@vger.kernel.org \
    --cc=kamel.bouhara@bootlin.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-i2c@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=nicolas.ferre@microchip.com \
    --cc=thomas.petazzoni@bootlin.com \
    --cc=wsa@the-dreams.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).