[PATCH v4 0/9] Add support for more Kontron i.MX6UL/ULL SoMs and boards

[PATCH v4 0/9] Add support for more Kontron i.MX6UL/ULL SoMs and boards

[Schrempf Frieder]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

In order to support more of the i.MX6UL/ULL-based SoMs and boards by
Kontron Electronics GmbH, we restructure the devicetrees to share common
parts and add new devicetrees for the missing boards.

Currently there are the following SoM flavors:
  * N6310: SoM with i.MX6UL-2, 256MB RAM, 256MB SPI NAND
  * N6311: SoM with i.MX6UL-2, 512MB RAM, 512MB SPI NAND (new)
  * N6411: SoM with i.MX6ULL, 512MB RAM, 512MB SPI NAND (new)

Each of the SoMs also features 1MB SPI NOR and an Ethernet PHY. The carrier
board for the evalkit is the same for all SoMs.

This series also includes some small enhancements and fixes for the shared
parts of the devicetrees.
---
Changes for v4:
===============
* Move the patch that removes the snvs-poweroff node before the file is moved
* Drop patch to specify bus-width as this is already set in imx6ul.dtsi
* Drop patch to add an entry for the dts files in MAINTAINERS
* Remove Fixes tags for patches that are not actually fixes

Changes for v3:
===============
* Add a patch that removes the snvs-poweroff node as it is not used
* Drop patch to add missing includes for gpio.h and irq.h as it is not needed
* Add Fixes tags to those patches that fix an issue in the existing devicetrees
* Add Reviewed-by tags from Krzysztof
* Minor improvements to commit messages and cover letter

Changes for v2:
===============
* Patch 1: Move the spi-flash node instead of duplicating it
* Patch 3: Add a missing include for dt-bindings/gpio/gpio.h
* Patch 11: Add patch to add missing includes for gpio.h and irq.h
* Add Reviewed-by tags from Krzysztof and Rob
---
Frieder Schrempf (9):
  ARM: dts: imx6ul-kontron-n6310: Move common SoM nodes to a separate
    file
  ARM: dts: Add support for two more Kontron SoMs N6311 and N6411
  ARM: dts: imx6ul-kontron-n6310-s: Disable the snvs-poweroff driver
  ARM: dts: imx6ul-kontron-n6310-s: Move common nodes to a separate file
  ARM: dts: Add support for two more Kontron evalkit boards 'N6311 S'
    and 'N6411 S'
  ARM: dts: imx6ul-kontron-n6x1x: Add 'chosen' node with 'stdout-path'
  ARM: dts: imx6ul-kontron-n6x1x-s: Add vbus-supply and overcurrent
    polarity to usb nodes
  ARM: dts: imx6ul-kontron-n6x1x-s: Remove an obsolete comment and fix
    indentation
  dt-bindings: arm: fsl: Add more Kontron i.MX6UL/ULL compatibles

 .../devicetree/bindings/arm/fsl.yaml          |  14 +
 arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts  | 405 +----------------
 .../boot/dts/imx6ul-kontron-n6310-som.dtsi    |  95 +---
 arch/arm/boot/dts/imx6ul-kontron-n6311-s.dts  |  16 +
 .../boot/dts/imx6ul-kontron-n6311-som.dtsi    |  40 ++
 arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi | 418 ++++++++++++++++++
 .../dts/imx6ul-kontron-n6x1x-som-common.dtsi  | 109 +++++
 arch/arm/boot/dts/imx6ull-kontron-n6411-s.dts |  16 +
 .../boot/dts/imx6ull-kontron-n6411-som.dtsi   |  40 ++
 9 files changed, 655 insertions(+), 498 deletions(-)
 create mode 100644 arch/arm/boot/dts/imx6ul-kontron-n6311-s.dts
 create mode 100644 arch/arm/boot/dts/imx6ul-kontron-n6311-som.dtsi
 create mode 100644 arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi
 create mode 100644 arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi
 create mode 100644 arch/arm/boot/dts/imx6ull-kontron-n6411-s.dts
 create mode 100644 arch/arm/boot/dts/imx6ull-kontron-n6411-som.dtsi

-- 
2.17.1

[PATCH v4 1/9] ARM: dts: imx6ul-kontron-n6310: Move common SoM nodes to a separate file

[Schrempf Frieder]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

The Kontron N6311 and N6411 SoMs are very similar to N6310. In
preparation to add support for them, we move the common nodes to a
separate file imx6ul-kontron-n6x1x-som-common.dtsi.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 .../boot/dts/imx6ul-kontron-n6310-som.dtsi    |  95 +---------------
 .../dts/imx6ul-kontron-n6x1x-som-common.dtsi  | 103 ++++++++++++++++++
 2 files changed, 104 insertions(+), 94 deletions(-)
 create mode 100644 arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi

diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi b/arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi
index a896b2348dd2..47d3ce5d255f 100644
--- a/arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi
+++ b/arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi
@@ -6,7 +6,7 @@
  */
 
 #include "imx6ul.dtsi"
-#include <dt-bindings/gpio/gpio.h>
+#include "imx6ul-kontron-n6x1x-som-common.dtsi"
 
 / {
 	model = "Kontron N6310 SOM";
@@ -18,49 +18,7 @@
 	};
 };
 
-&ecspi2 {
-	cs-gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi2>;
-	status = "okay";
-
-	spi-flash@0 {
-		compatible = "mxicy,mx25v8035f", "jedec,spi-nor";
-		spi-max-frequency = <50000000>;
-		reg = <0>;
-	};
-};
-
-&fec1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet1_mdio>;
-	phy-mode = "rmii";
-	phy-handle = <&ethphy1>;
-	status = "okay";
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		ethphy1: ethernet-phy@1 {
-			reg = <1>;
-			micrel,led-mode = <0>;
-			clocks = <&clks IMX6UL_CLK_ENET_REF>;
-			clock-names = "rmii-ref";
-		};
-	};
-};
-
-&fec2 {
-	phy-mode = "rmii";
-	status = "disabled";
-};
-
 &qspi {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_qspi>;
-	status = "okay";
-
 	spi-flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -81,54 +39,3 @@
 		};
 	};
 };
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_reset_out>;
-
-	pinctrl_ecspi2: ecspi2grp {
-		fsl,pins = <
-			MX6UL_PAD_CSI_DATA03__ECSPI2_MISO      0x100b1
-			MX6UL_PAD_CSI_DATA02__ECSPI2_MOSI      0x100b1
-			MX6UL_PAD_CSI_DATA00__ECSPI2_SCLK      0x100b1
-			MX6UL_PAD_CSI_DATA01__GPIO4_IO22       0x100b1
-		>;
-	};
-
-	pinctrl_enet1: enet1grp {
-		fsl,pins = <
-			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN      0x1b0b0
-			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER      0x1b0b0
-			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
-			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
-			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN      0x1b0b0
-			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
-			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
-			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1  0x4001b009
-		>;
-	};
-
-	pinctrl_enet1_mdio: enet1mdiogrp {
-		fsl,pins = <
-			MX6UL_PAD_GPIO1_IO07__ENET1_MDC         0x1b0b0
-			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO        0x1b0b0
-		>;
-	};
-
-	pinctrl_qspi: qspigrp {
-		fsl,pins = <
-			MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK        0x70a1
-			MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00   0x70a1
-			MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01     0x70a1
-			MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02     0x70a1
-			MX6UL_PAD_NAND_CLE__QSPI_A_DATA03       0x70a1
-			MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B        0x70a1
-		>;
-	};
-
-	pinctrl_reset_out: rstoutgrp {
-		fsl,pins = <
-			MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09      0x1b0b0
-		>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi b/arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi
new file mode 100644
index 000000000000..a843e028bcde
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi
@@ -0,0 +1,103 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+&ecspi2 {
+	cs-gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	status = "okay";
+
+	spi-flash@0 {
+		compatible = "mxicy,mx25v8035f", "jedec,spi-nor";
+		spi-max-frequency = <50000000>;
+		reg = <0>;
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet1_mdio>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy1>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@1 {
+			reg = <1>;
+			micrel,led-mode = <0>;
+			clocks = <&clks IMX6UL_CLK_ENET_REF>;
+			clock-names = "rmii-ref";
+		};
+	};
+};
+
+&fec2 {
+	phy-mode = "rmii";
+	status = "disabled";
+};
+
+&qspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_qspi>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_reset_out>;
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA03__ECSPI2_MISO      0x100b1
+			MX6UL_PAD_CSI_DATA02__ECSPI2_MOSI      0x100b1
+			MX6UL_PAD_CSI_DATA00__ECSPI2_SCLK      0x100b1
+			MX6UL_PAD_CSI_DATA01__GPIO4_IO22       0x100b1
+		>;
+	};
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN      0x1b0b0
+			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER      0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN      0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1  0x4001b009
+		>;
+	};
+
+	pinctrl_enet1_mdio: enet1mdiogrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO07__ENET1_MDC         0x1b0b0
+			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO        0x1b0b0
+		>;
+	};
+
+	pinctrl_qspi: qspigrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK        0x70a1
+			MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00   0x70a1
+			MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01     0x70a1
+			MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02     0x70a1
+			MX6UL_PAD_NAND_CLE__QSPI_A_DATA03       0x70a1
+			MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B        0x70a1
+		>;
+	};
+
+	pinctrl_reset_out: rstoutgrp {
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09      0x1b0b0
+		>;
+	};
+};
-- 
2.17.1

[PATCH v4 2/9] ARM: dts: Add support for two more Kontron SoMs N6311 and N6411

[Schrempf Frieder]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

The N6311 and the N6411 SoM are similar to the Kontron N6310 SoM.
They are pin-compatible, but feature a larger RAM and NAND flash
(512MiB instead of 256MiB). Further, the N6411 has an i.MX6ULL SoC,
instead of an i.MX6UL.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 .../boot/dts/imx6ul-kontron-n6311-som.dtsi    | 40 +++++++++++++++++++
 .../boot/dts/imx6ull-kontron-n6411-som.dtsi   | 40 +++++++++++++++++++
 2 files changed, 80 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6ul-kontron-n6311-som.dtsi
 create mode 100644 arch/arm/boot/dts/imx6ull-kontron-n6411-som.dtsi

diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6311-som.dtsi b/arch/arm/boot/dts/imx6ul-kontron-n6311-som.dtsi
new file mode 100644
index 000000000000..a095a7654ac6
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-kontron-n6311-som.dtsi
@@ -0,0 +1,40 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ */
+
+#include "imx6ul.dtsi"
+#include "imx6ul-kontron-n6x1x-som-common.dtsi"
+
+/ {
+	model = "Kontron N6311 SOM";
+	compatible = "kontron,imx6ul-n6311-som", "fsl,imx6ul";
+
+	memory@80000000 {
+		reg = <0x80000000 0x20000000>;
+		device_type = "memory";
+	};
+};
+
+&qspi {
+	spi-flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "spi-nand";
+		spi-max-frequency = <104000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		reg = <0>;
+
+		partition@0 {
+			label = "ubi1";
+			reg = <0x00000000 0x08000000>;
+		};
+
+		partition@8000000 {
+			label = "ubi2";
+			reg = <0x08000000 0x18000000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ull-kontron-n6411-som.dtsi b/arch/arm/boot/dts/imx6ull-kontron-n6411-som.dtsi
new file mode 100644
index 000000000000..b7e984284e1a
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-kontron-n6411-som.dtsi
@@ -0,0 +1,40 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ */
+
+#include "imx6ull.dtsi"
+#include "imx6ul-kontron-n6x1x-som-common.dtsi"
+
+/ {
+	model = "Kontron N6411 SOM";
+	compatible = "kontron,imx6ull-n6311-som", "fsl,imx6ull";
+
+	memory@80000000 {
+		reg = <0x80000000 0x20000000>;
+		device_type = "memory";
+	};
+};
+
+&qspi {
+	spi-flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "spi-nand";
+		spi-max-frequency = <104000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		reg = <0>;
+
+		partition@0 {
+			label = "ubi1";
+			reg = <0x00000000 0x08000000>;
+		};
+
+		partition@8000000 {
+			label = "ubi2";
+			reg = <0x08000000 0x18000000>;
+		};
+	};
+};
-- 
2.17.1

[PATCH v4 3/9] ARM: dts: imx6ul-kontron-n6310-s: Disable the snvs-poweroff driver

[Schrempf Frieder]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

The snvs-poweroff driver can power off the system by pulling the
PMIC_ON_REQ signal low, to let the PMIC disable the power.
The Kontron SoMs do not have this signal connected, so let's remove
the node.

This fixes a real issue when the signal is asserted at poweroff,
but not actually causing the power to turn off. It was observed,
that in this case the system would not shut down properly.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Fixes: 1ea4b76cdfde ("ARM: dts: imx6ul-kontron-n6310: Add Kontron i.MX6UL N6310 SoM and boards")
---
 arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts | 4 ----
 1 file changed, 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts b/arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts
index 0205fd56d975..4e99e6c79a68 100644
--- a/arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts
+++ b/arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts
@@ -157,10 +157,6 @@
 	status = "okay";
 };
 
-&snvs_poweroff {
-	status = "okay";
-};
-
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1>;
-- 
2.17.1

[PATCH v4 4/9] ARM: dts: imx6ul-kontron-n6310-s: Move common nodes to a separate file

[Schrempf Frieder]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

The baseboard for the Kontron N6310 SoM is also used for other SoMs
such as N6311 and N6411. In order to share the code, we move the
definitions of the baseboard to a separate dtsi file.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts  | 401 +----------------
 arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi | 410 ++++++++++++++++++
 2 files changed, 411 insertions(+), 400 deletions(-)
 create mode 100644 arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi

diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts b/arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts
index 4e99e6c79a68..5a3e06d6219b 100644
--- a/arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts
+++ b/arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts
@@ -8,409 +8,10 @@
 /dts-v1/;
 
 #include "imx6ul-kontron-n6310-som.dtsi"
+#include "imx6ul-kontron-n6x1x-s.dtsi"
 
 / {
 	model = "Kontron N6310 S";
 	compatible = "kontron,imx6ul-n6310-s", "kontron,imx6ul-n6310-som",
 		     "fsl,imx6ul";
-
-	gpio-leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpio_leds>;
-
-		led1 {
-			label = "debug-led1";
-			gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
-			default-state = "off";
-			linux,default-trigger = "heartbeat";
-		};
-
-		led2 {
-			label = "debug-led2";
-			gpios = <&gpio5 3 GPIO_ACTIVE_LOW>;
-			default-state = "off";
-		};
-
-		led3 {
-			label = "debug-led3";
-			gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
-			default-state = "off";
-		};
-	};
-
-	pwm-beeper {
-		compatible = "pwm-beeper";
-		pwms = <&pwm8 0 5000>;
-	};
-
-	reg_3v3: regulator-3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
-		compatible = "regulator-fixed";
-		regulator-name = "usb_otg1_vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	reg_vref_adc: regulator-vref-adc {
-		compatible = "regulator-fixed";
-		regulator-name = "vref-adc";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-};
-
-&adc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_adc1>;
-	num-channels = <3>;
-	vref-supply = <&reg_vref_adc>;
-	status = "okay";
-};
-
-&can2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_flexcan2>;
-	status = "okay";
-};
-
-&ecspi1 {
-	cs-gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi1>;
-	status = "okay";
-
-	eeprom@0 {
-		compatible = "anvo,anv32e61w", "atmel,at25";
-		reg = <0>;
-		spi-max-frequency = <20000000>;
-		spi-cpha;
-		spi-cpol;
-		pagesize = <1>;
-		size = <8192>;
-		address-width = <16>;
-	};
-};
-
-&fec1 {
-	pinctrl-0 = <&pinctrl_enet1>;
-	/delete-node/ mdio;
-};
-
-&fec2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet2 &pinctrl_enet2_mdio>;
-	phy-mode = "rmii";
-	phy-handle = <&ethphy2>;
-	status = "okay";
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		ethphy1: ethernet-phy@1 {
-			reg = <1>;
-			micrel,led-mode = <0>;
-			clocks = <&clks IMX6UL_CLK_ENET_REF>;
-			clock-names = "rmii-ref";
-		};
-
-		ethphy2: ethernet-phy@2 {
-			reg = <2>;
-			micrel,led-mode = <0>;
-			clocks = <&clks IMX6UL_CLK_ENET2_REF>;
-			clock-names = "rmii-ref";
-		};
-	};
-};
-
-&i2c1 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c1>;
-	status = "okay";
-};
-
-&i2c4 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c4>;
-	status = "okay";
-
-	rtc@32 {
-		compatible = "epson,rx8900";
-		reg = <0x32>;
-	};
-};
-
-&pwm8 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm8>;
-	status = "okay";
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
-	status = "okay";
-};
-
-&uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
-	linux,rs485-enabled-at-boot-time;
-	rs485-rx-during-tx;
-	rs485-rts-active-low;
-	uart-has-rtscts;
-	status = "okay";
-};
-
-&uart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart3>;
-	fsl,uart-has-rtscts;
-	status = "okay";
-};
-
-&uart4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart4>;
-	status = "okay";
-};
-
-&usbotg1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbotg1>;
-	dr_mode = "otg";
-	srp-disable;
-	hnp-disable;
-	adp-disable;
-	vbus-supply = <&reg_usb_otg1_vbus>;
-	status = "okay";
-};
-
-&usbotg2 {
-	dr_mode = "host";
-	disable-over-current;
-	status = "okay";
-};
-
-&usdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc1>;
-	cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
-	keep-power-in-suspend;
-	wakeup-source;
-	vmmc-supply = <&reg_3v3>;
-	voltage-ranges = <3300 3300>;
-	no-1-8-v;
-	status = "okay";
-};
-
-&usdhc2 {
-	pinctrl-names = "default", "state_100mhz", "state_200mhz";
-	pinctrl-0 = <&pinctrl_usdhc2>;
-	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
-	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
-	non-removable;
-	keep-power-in-suspend;
-	wakeup-source;
-	vmmc-supply = <&reg_3v3>;
-	voltage-ranges = <3300 3300>;
-	no-1-8-v;
-	status = "okay";
-};
-
-&wdog1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_wdog>;
-	fsl,ext-reset-output;
-	status = "okay";
-};
-
-&iomuxc {
-	pinctrl-0 = <&pinctrl_reset_out &pinctrl_gpio>;
-
-	pinctrl_adc1: adc1grp {
-		fsl,pins = <
-			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02	0xb0
-			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0xb0
-			MX6UL_PAD_GPIO1_IO08__GPIO1_IO08	0xb0
-		>;
-	};
-
-	/* FRAM */
-	pinctrl_ecspi1: ecspi1grp {
-		fsl,pins = <
-			MX6UL_PAD_CSI_DATA07__ECSPI1_MISO	0x100b1
-			MX6UL_PAD_CSI_DATA06__ECSPI1_MOSI	0x100b1
-			MX6UL_PAD_CSI_DATA04__ECSPI1_SCLK	0x100b1
-			MX6UL_PAD_CSI_DATA05__GPIO4_IO26	0x100b1	/* ECSPI1-CS1 */
-		>;
-	};
-
-	pinctrl_enet2: enet2grp {
-		fsl,pins = <
-			MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN	0x1b0b0
-			MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER	0x1b0b0
-			MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00	0x1b0b0
-			MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01	0x1b0b0
-			MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN	0x1b0b0
-			MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00	0x1b0b0
-			MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01	0x1b0b0
-			MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	0x4001b009
-		>;
-	};
-
-	pinctrl_enet2_mdio: enet2mdiogrp {
-		fsl,pins = <
-			MX6UL_PAD_GPIO1_IO07__ENET2_MDC         0x1b0b0
-			MX6UL_PAD_GPIO1_IO06__ENET2_MDIO        0x1b0b0
-		>;
-	};
-
-	pinctrl_flexcan2: flexcan2grp{
-		fsl,pins = <
-			MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX	0x1b020
-			MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX	0x1b020
-		>;
-	};
-
-	pinctrl_gpio: gpiogrp {
-		fsl,pins = <
-			MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05	0x1b0b0 /* DOUT1 */
-			MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04	0x1b0b0 /* DIN1 */
-			MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x1b0b0 /* DOUT2 */
-			MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x1b0b0 /* DIN2 */
-		>;
-	};
-
-	pinctrl_gpio_leds: gpioledsgrp {
-		fsl,pins = <
-			MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30	0x1b0b0	/* LED H14 */
-			MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x1b0b0	/* LED H15 */
-			MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x1b0b0	/* LED H16 */
-		>;
-	};
-
-	pinctrl_i2c1: i2c1grp {
-		fsl,pins = <
-			MX6UL_PAD_CSI_PIXCLK__I2C1_SCL		0x4001b8b0
-			MX6UL_PAD_CSI_MCLK__I2C1_SDA		0x4001b8b0
-		>;
-	};
-
-	pinctrl_i2c4: i2c4grp {
-		fsl,pins = <
-			MX6UL_PAD_UART2_TX_DATA__I2C4_SCL	0x4001f8b0
-			MX6UL_PAD_UART2_RX_DATA__I2C4_SDA	0x4001f8b0
-		>;
-	};
-
-	pinctrl_pwm8: pwm8grp {
-		fsl,pins = <
-			MX6UL_PAD_CSI_HSYNC__PWM8_OUT		0x110b0
-		>;
-	};
-
-	pinctrl_uart1: uart1grp {
-		fsl,pins = <
-			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
-			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
-		>;
-	};
-
-	pinctrl_uart2: uart2grp {
-		fsl,pins = <
-			MX6UL_PAD_NAND_DATA04__UART2_DCE_TX	0x1b0b1
-			MX6UL_PAD_NAND_DATA05__UART2_DCE_RX	0x1b0b1
-			MX6UL_PAD_NAND_DATA06__UART2_DCE_CTS	0x1b0b1
-			/*
-			 * mux unused RTS to make sure it doesn't cause
-			 * any interrupts when it is undefined
-			 */
-			MX6UL_PAD_NAND_DATA07__UART2_DCE_RTS	0x1b0b1
-		>;
-	};
-
-	pinctrl_uart3: uart3grp {
-		fsl,pins = <
-			MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX	0x1b0b1
-			MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX	0x1b0b1
-			MX6UL_PAD_UART3_CTS_B__UART3_DCE_CTS	0x1b0b1
-			MX6UL_PAD_UART3_RTS_B__UART3_DCE_RTS	0x1b0b1
-		>;
-	};
-
-	pinctrl_uart4: uart4grp {
-		fsl,pins = <
-			MX6UL_PAD_UART4_TX_DATA__UART4_DCE_TX	0x1b0b1
-			MX6UL_PAD_UART4_RX_DATA__UART4_DCE_RX	0x1b0b1
-		>;
-	};
-
-	pinctrl_usbotg1: usbotg1 {
-		fsl,pins = <
-			MX6UL_PAD_GPIO1_IO04__GPIO1_IO04	0x1b0b0
-		>;
-	};
-
-	pinctrl_usdhc1: usdhc1grp {
-		fsl,pins = <
-			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059
-			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10059
-			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059
-			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059
-			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059
-			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059
-			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x100b1	/* SD1_CD */
-		>;
-	};
-
-	pinctrl_usdhc2: usdhc2grp {
-		fsl,pins = <
-			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x10059
-			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x17059
-			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x17059
-			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x17059
-			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x17059
-			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x17059
-		>;
-	};
-
-	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
-		fsl,pins = <
-			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x100b9
-			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x170b9
-			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x170b9
-			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x170b9
-			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x170b9
-			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x170b9
-		>;
-	};
-
-	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
-		fsl,pins = <
-			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x100f9
-			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x170f9
-			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x170f9
-			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x170f9
-			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x170f9
-			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x170f9
-		>;
-	};
-
-	pinctrl_wdog: wdoggrp {
-		fsl,pins = <
-			MX6UL_PAD_GPIO1_IO09__WDOG1_WDOG_ANY	0x30b0
-		>;
-	};
 };
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi b/arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi
new file mode 100644
index 000000000000..93a0f0ca5b84
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi
@@ -0,0 +1,410 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+
+		led1 {
+			label = "debug-led1";
+			gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+			linux,default-trigger = "heartbeat";
+		};
+
+		led2 {
+			label = "debug-led2";
+			gpios = <&gpio5 3 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led3 {
+			label = "debug-led3";
+			gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	pwm-beeper {
+		compatible = "pwm-beeper";
+		pwms = <&pwm8 0 5000>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_vref_adc: regulator-vref-adc {
+		compatible = "regulator-fixed";
+		regulator-name = "vref-adc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&adc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc1>;
+	num-channels = <3>;
+	vref-supply = <&reg_vref_adc>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	status = "okay";
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	eeprom@0 {
+		compatible = "anvo,anv32e61w", "atmel,at25";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+		spi-cpha;
+		spi-cpol;
+		pagesize = <1>;
+		size = <8192>;
+		address-width = <16>;
+	};
+};
+
+&fec1 {
+	pinctrl-0 = <&pinctrl_enet1>;
+	/delete-node/ mdio;
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet2 &pinctrl_enet2_mdio>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy2>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@1 {
+			reg = <1>;
+			micrel,led-mode = <0>;
+			clocks = <&clks IMX6UL_CLK_ENET_REF>;
+			clock-names = "rmii-ref";
+		};
+
+		ethphy2: ethernet-phy@2 {
+			reg = <2>;
+			micrel,led-mode = <0>;
+			clocks = <&clks IMX6UL_CLK_ENET2_REF>;
+			clock-names = "rmii-ref";
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+};
+
+&i2c4 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	status = "okay";
+
+	rtc@32 {
+		compatible = "epson,rx8900";
+		reg = <0x32>;
+	};
+};
+
+&pwm8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm8>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	linux,rs485-enabled-at-boot-time;
+	rs485-rx-during-tx;
+	rs485-rts-active-low;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	fsl,uart-has-rtscts;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1>;
+	dr_mode = "otg";
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	vbus-supply = <&reg_usb_otg1_vbus>;
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+	keep-power-in-suspend;
+	wakeup-source;
+	vmmc-supply = <&reg_3v3>;
+	voltage-ranges = <3300 3300>;
+	no-1-8-v;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	non-removable;
+	keep-power-in-suspend;
+	wakeup-source;
+	vmmc-supply = <&reg_3v3>;
+	voltage-ranges = <3300 3300>;
+	no-1-8-v;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-0 = <&pinctrl_reset_out &pinctrl_gpio>;
+
+	pinctrl_adc1: adc1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02	0xb0
+			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0xb0
+			MX6UL_PAD_GPIO1_IO08__GPIO1_IO08	0xb0
+		>;
+	};
+
+	/* FRAM */
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA07__ECSPI1_MISO	0x100b1
+			MX6UL_PAD_CSI_DATA06__ECSPI1_MOSI	0x100b1
+			MX6UL_PAD_CSI_DATA04__ECSPI1_SCLK	0x100b1
+			MX6UL_PAD_CSI_DATA05__GPIO4_IO26	0x100b1	/* ECSPI1-CS1 */
+		>;
+	};
+
+	pinctrl_enet2: enet2grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN	0x1b0b0
+			MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00	0x1b0b0
+			MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01	0x1b0b0
+			MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	0x4001b009
+		>;
+	};
+
+	pinctrl_enet2_mdio: enet2mdiogrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO07__ENET2_MDC         0x1b0b0
+			MX6UL_PAD_GPIO1_IO06__ENET2_MDIO        0x1b0b0
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2grp{
+		fsl,pins = <
+			MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX	0x1b020
+			MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX	0x1b020
+		>;
+	};
+
+	pinctrl_gpio: gpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05	0x1b0b0 /* DOUT1 */
+			MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04	0x1b0b0 /* DIN1 */
+			MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x1b0b0 /* DOUT2 */
+			MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x1b0b0 /* DIN2 */
+		>;
+	};
+
+	pinctrl_gpio_leds: gpioledsgrp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30	0x1b0b0	/* LED H14 */
+			MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x1b0b0	/* LED H15 */
+			MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x1b0b0	/* LED H16 */
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_PIXCLK__I2C1_SCL		0x4001b8b0
+			MX6UL_PAD_CSI_MCLK__I2C1_SDA		0x4001b8b0
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_TX_DATA__I2C4_SCL	0x4001f8b0
+			MX6UL_PAD_UART2_RX_DATA__I2C4_SDA	0x4001f8b0
+		>;
+	};
+
+	pinctrl_pwm8: pwm8grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_HSYNC__PWM8_OUT		0x110b0
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_DATA04__UART2_DCE_TX	0x1b0b1
+			MX6UL_PAD_NAND_DATA05__UART2_DCE_RX	0x1b0b1
+			MX6UL_PAD_NAND_DATA06__UART2_DCE_CTS	0x1b0b1
+			/*
+			 * mux unused RTS to make sure it doesn't cause
+			 * any interrupts when it is undefined
+			 */
+			MX6UL_PAD_NAND_DATA07__UART2_DCE_RTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX	0x1b0b1
+			MX6UL_PAD_UART3_CTS_B__UART3_DCE_CTS	0x1b0b1
+			MX6UL_PAD_UART3_RTS_B__UART3_DCE_RTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_TX_DATA__UART4_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART4_RX_DATA__UART4_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1 {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO04__GPIO1_IO04	0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10059
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x100b1	/* SD1_CD */
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x10059
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x17059
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x17059
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x17059
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x17059
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x17059
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x100b9
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x170b9
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x170b9
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x170b9
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x170b9
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x100f9
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x170f9
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x170f9
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x170f9
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x170f9
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x170f9
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO09__WDOG1_WDOG_ANY	0x30b0
+		>;
+	};
+};
-- 
2.17.1

[PATCH v4 5/9] ARM: dts: Add support for two more Kontron evalkit boards 'N6311 S' and 'N6411 S'

[Schrempf Frieder]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

The 'N6311 S' and the 'N6411 S' are similar to the Kontron 'N6310 S'
evaluation kit boards. Instead of the N6310 SoM, they feature a N6311
or N6411 SoM.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 arch/arm/boot/dts/imx6ul-kontron-n6311-s.dts  | 16 ++++++++++++++++
 arch/arm/boot/dts/imx6ull-kontron-n6411-s.dts | 16 ++++++++++++++++
 2 files changed, 32 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6ul-kontron-n6311-s.dts
 create mode 100644 arch/arm/boot/dts/imx6ull-kontron-n6411-s.dts

diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6311-s.dts b/arch/arm/boot/dts/imx6ul-kontron-n6311-s.dts
new file mode 100644
index 000000000000..239a1af3aeaa
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-kontron-n6311-s.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ */
+
+/dts-v1/;
+
+#include "imx6ul-kontron-n6311-som.dtsi"
+#include "imx6ul-kontron-n6x1x-s.dtsi"
+
+/ {
+	model = "Kontron N6311 S";
+	compatible = "kontron,imx6ul-n6311-s", "kontron,imx6ul-n6311-som",
+		     "fsl,imx6ul";
+};
diff --git a/arch/arm/boot/dts/imx6ull-kontron-n6411-s.dts b/arch/arm/boot/dts/imx6ull-kontron-n6411-s.dts
new file mode 100644
index 000000000000..57588a5e1e34
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-kontron-n6411-s.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2019 Kontron Electronics GmbH
+ */
+
+/dts-v1/;
+
+#include "imx6ull-kontron-n6411-som.dtsi"
+#include "imx6ul-kontron-n6x1x-s.dtsi"
+
+/ {
+	model = "Kontron N6411 S";
+	compatible = "kontron,imx6ull-n6411-s", "kontron,imx6ull-n6411-som",
+		     "fsl,imx6ull";
+};
-- 
2.17.1

[PATCH v4 6/9] ARM: dts: imx6ul-kontron-n6x1x: Add 'chosen' node with 'stdout-path'

[Schrempf Frieder]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

The Kontron N6x1x SoMs all use uart4 as a debug serial interface.
Therefore we set it in the 'chosen' node.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi b/arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi
index a843e028bcde..a17af4d9bfdf 100644
--- a/arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi
+++ b/arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi
@@ -7,6 +7,12 @@
 
 #include <dt-bindings/gpio/gpio.h>
 
+/ {
+	chosen {
+		stdout-path = &uart4;
+	};
+};
+
 &ecspi2 {
 	cs-gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
 	pinctrl-names = "default";
-- 
2.17.1

[PATCH v4 7/9] ARM: dts: imx6ul-kontron-n6x1x-s: Add vbus-supply and overcurrent polarity to usb nodes

[Schrempf Frieder]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

To silence the warnings shown by the driver at boot time, we add a
fixed regulator for the 5V supply of usbotg2 and specify the polarity
of the overcurrent signal for usbotg1.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi b/arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi
index 93a0f0ca5b84..5725e5fc271b 100644
--- a/arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi
+++ b/arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi
@@ -45,6 +45,13 @@
 		regulator-max-microvolt = <3300000>;
 	};
 
+	reg_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
 	reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "usb_otg1_vbus";
@@ -187,6 +194,7 @@
 	srp-disable;
 	hnp-disable;
 	adp-disable;
+	over-current-active-low;
 	vbus-supply = <&reg_usb_otg1_vbus>;
 	status = "okay";
 };
@@ -194,6 +202,7 @@
 &usbotg2 {
 	dr_mode = "host";
 	disable-over-current;
+	vbus-supply = <&reg_5v>;
 	status = "okay";
 };
 
-- 
2.17.1

[PATCH v4 8/9] ARM: dts: imx6ul-kontron-n6x1x-s: Remove an obsolete comment and fix indentation

[Schrempf Frieder]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

The ECSPI1 is not used for a FRAM chip, so remove the comment.
While at it, also change some whitespaces to tabs to comply with the
indentation style of the rest of the file.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi | 13 ++++++-------
 1 file changed, 6 insertions(+), 7 deletions(-)

diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi b/arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi
index 5725e5fc271b..f05e91841202 100644
--- a/arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi
+++ b/arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi
@@ -250,7 +250,6 @@
 		>;
 	};
 
-	/* FRAM */
 	pinctrl_ecspi1: ecspi1grp {
 		fsl,pins = <
 			MX6UL_PAD_CSI_DATA07__ECSPI1_MISO	0x100b1
@@ -275,8 +274,8 @@
 
 	pinctrl_enet2_mdio: enet2mdiogrp {
 		fsl,pins = <
-			MX6UL_PAD_GPIO1_IO07__ENET2_MDC         0x1b0b0
-			MX6UL_PAD_GPIO1_IO06__ENET2_MDIO        0x1b0b0
+			MX6UL_PAD_GPIO1_IO07__ENET2_MDC		0x1b0b0
+			MX6UL_PAD_GPIO1_IO06__ENET2_MDIO	0x1b0b0
 		>;
 	};
 
@@ -289,10 +288,10 @@
 
 	pinctrl_gpio: gpiogrp {
 		fsl,pins = <
-			MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05	0x1b0b0 /* DOUT1 */
-			MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04	0x1b0b0 /* DIN1 */
-			MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x1b0b0 /* DOUT2 */
-			MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x1b0b0 /* DIN2 */
+			MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05	0x1b0b0	/* DOUT1 */
+			MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04	0x1b0b0	/* DIN1 */
+			MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x1b0b0	/* DOUT2 */
+			MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x1b0b0	/* DIN2 */
 		>;
 	};
 
-- 
2.17.1

[PATCH v4 9/9] dt-bindings: arm: fsl: Add more Kontron i.MX6UL/ULL compatibles

[Schrempf Frieder]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

Add the compatibles for Kontron i.MX6UL N6311 SoM and boards and
the compatibles for Kontron i.MX6ULL N6411 SoM and boards.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/arm/fsl.yaml | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 1b4b4e6573b5..6d718272725d 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -162,6 +162,7 @@ properties:
           - enum:
               - fsl,imx6ul-14x14-evk      # i.MX6 UltraLite 14x14 EVK Board
               - kontron,imx6ul-n6310-som  # Kontron N6310 SOM
+              - kontron,imx6ul-n6311-som  # Kontron N6311 SOM
           - const: fsl,imx6ul
 
       - description: Kontron N6310 S Board
@@ -170,6 +171,12 @@ properties:
           - const: kontron,imx6ul-n6310-som
           - const: fsl,imx6ul
 
+      - description: Kontron N6311 S Board
+        items:
+          - const: kontron,imx6ul-n6311-s
+          - const: kontron,imx6ul-n6311-som
+          - const: fsl,imx6ul
+
       - description: Kontron N6310 S 43 Board
         items:
           - const: kontron,imx6ul-n6310-s-43
@@ -181,6 +188,13 @@ properties:
         items:
           - enum:
               - fsl,imx6ull-14x14-evk     # i.MX6 UltraLiteLite 14x14 EVK Board
+              - kontron,imx6ull-n6411-som # Kontron N6411 SOM
+          - const: fsl,imx6ull
+
+      - description: Kontron N6411 S Board
+        items:
+          - const: kontron,imx6ull-n6411-s
+          - const: kontron,imx6ull-n6411-som
           - const: fsl,imx6ull
 
       - description: i.MX6ULZ based Boards
-- 
2.17.1

Re: [PATCH v4 0/9] Add support for more Kontron i.MX6UL/ULL SoMs and boards

[Shawn Guo]

On Mon, Nov 04, 2019 at 11:53:56AM +0000, Schrempf Frieder wrote:
> Frieder Schrempf (9):
>   ARM: dts: imx6ul-kontron-n6310: Move common SoM nodes to a separate
>     file
>   ARM: dts: Add support for two more Kontron SoMs N6311 and N6411
>   ARM: dts: imx6ul-kontron-n6310-s: Disable the snvs-poweroff driver
>   ARM: dts: imx6ul-kontron-n6310-s: Move common nodes to a separate file
>   ARM: dts: Add support for two more Kontron evalkit boards 'N6311 S'
>     and 'N6411 S'
>   ARM: dts: imx6ul-kontron-n6x1x: Add 'chosen' node with 'stdout-path'
>   ARM: dts: imx6ul-kontron-n6x1x-s: Add vbus-supply and overcurrent
>     polarity to usb nodes
>   ARM: dts: imx6ul-kontron-n6x1x-s: Remove an obsolete comment and fix
>     indentation
>   dt-bindings: arm: fsl: Add more Kontron i.MX6UL/ULL compatibles

Applied all, thanks.