From: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
To: Hans de Goede <hdegoede@redhat.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>,
Joonas Lahtinen <joonas.lahtinen@linux.intel.com>,
Rodrigo Vivi <rodrigo.vivi@intel.com>,
Lee Jones <lee.jones@linaro.org>,
Linus Walleij <linus.walleij@linaro.org>,
intel-gfx <intel-gfx@lists.freedesktop.org>,
dri-devel@lists.freedesktop.org, linux-kernel@vger.kernel.org,
linux-gpio@vger.kernel.org
Subject: Re: [PATCH 3/5] drm/i915/dsi: Init panel-enable GPIO to low when the LCD is initially off
Date: Mon, 16 Dec 2019 16:14:50 +0200 [thread overview]
Message-ID: <20191216141450.GU1208@intel.com> (raw)
In-Reply-To: <c7fe3911-be20-33dd-96c1-58eccd0f323f@redhat.com>
On Mon, Dec 16, 2019 at 02:51:54PM +0100, Hans de Goede wrote:
> Hi,
>
> Thank you for the reviews.
>
> On 16-12-2019 14:45, Ville Syrjälä wrote:
> > On Sun, Dec 15, 2019 at 05:38:08PM +0100, Hans de Goede wrote:
> >> When the LCD has not been turned on by the firmware/GOP, because e.g. the
> >> device was booted with an external monitor connected over HDMI, we should
> >> not turn on the panel-enable GPIO when we request it.
> >>
> >> Turning on the panel-enable GPIO when we request it, means we turn it on
> >> too early in the init-sequence, which causes some panels to not correctly
> >> light up.
> >>
> >> This commits adds a panel_is_on parameter to intel_dsi_vbt_gpio_init()
> >> and makes intel_dsi_vbt_gpio_init() set the initial GPIO value accordingly.
> >>
> >> This fixes the panel not lighting up on a Thundersoft TST168 tablet when
> >> booted with an external monitor connected over HDMI.
> >>
> >> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> >> ---
> >> drivers/gpu/drm/i915/display/intel_dsi.h | 2 +-
> >> drivers/gpu/drm/i915/display/intel_dsi_vbt.c | 7 +++----
> >> drivers/gpu/drm/i915/display/vlv_dsi.c | 2 +-
> >> 3 files changed, 5 insertions(+), 6 deletions(-)
> >>
> >> diff --git a/drivers/gpu/drm/i915/display/intel_dsi.h b/drivers/gpu/drm/i915/display/intel_dsi.h
> >> index de7e51cd3460..675771ea91aa 100644
> >> --- a/drivers/gpu/drm/i915/display/intel_dsi.h
> >> +++ b/drivers/gpu/drm/i915/display/intel_dsi.h
> >> @@ -203,7 +203,7 @@ void bxt_dsi_reset_clocks(struct intel_encoder *encoder, enum port port);
> >>
> >> /* intel_dsi_vbt.c */
> >> bool intel_dsi_vbt_init(struct intel_dsi *intel_dsi, u16 panel_id);
> >> -void intel_dsi_vbt_gpio_init(struct intel_dsi *intel_dsi);
> >> +void intel_dsi_vbt_gpio_init(struct intel_dsi *intel_dsi, bool panel_is_on);
> >> void intel_dsi_vbt_gpio_cleanup(struct intel_dsi *intel_dsi);
> >> void intel_dsi_vbt_exec_sequence(struct intel_dsi *intel_dsi,
> >> enum mipi_seq seq_id);
> >> diff --git a/drivers/gpu/drm/i915/display/intel_dsi_vbt.c b/drivers/gpu/drm/i915/display/intel_dsi_vbt.c
> >> index 5352e8c9eca5..027970348b22 100644
> >> --- a/drivers/gpu/drm/i915/display/intel_dsi_vbt.c
> >> +++ b/drivers/gpu/drm/i915/display/intel_dsi_vbt.c
> >> @@ -688,17 +688,16 @@ bool intel_dsi_vbt_init(struct intel_dsi *intel_dsi, u16 panel_id)
> >> * On some BYT/CHT devs some sequences are incomplete and we need to manually
> >> * control some GPIOs.
> >> */
> >> -void intel_dsi_vbt_gpio_init(struct intel_dsi *intel_dsi)
> >> +void intel_dsi_vbt_gpio_init(struct intel_dsi *intel_dsi, bool panel_is_on)
> >> {
> >> struct drm_device *dev = intel_dsi->base.base.dev;
> >> struct drm_i915_private *dev_priv = to_i915(dev);
> >> struct mipi_config *mipi_config = dev_priv->vbt.dsi.config;
> >> + enum gpiod_flags flags = panel_is_on ? GPIOD_OUT_HIGH : GPIOD_OUT_LOW;
> >
> > Can't we just tell it not to change the current setting?
>
> We could use GPIOD_ASIS for that, but with the SoC pins (when the PMIC is
> not used for backlight control) things get a bit muddy, I've seen several
> instances of this message from drivers/pinctrl/intel/pinctrl-baytrail.c
> trigger when the GOP did not init the panel:
>
> dev_warn(vg->dev, FW_BUG "pin %u forcibly re-configured as GPIO\n", offset);
>
> And in that case with GPIOD_ASIS I have no idea which we initially get,
> so this approach, where we clearly define which initial value we want,
> seems better.
I suppose. Probably better to not abuse the current_mode pointer for
that though and just explicitly call encoder->get_hw_state() instead.
>
> Regards,
>
> Hans
>
> p.s.
>
> The intel-gfx CI seems to seriously dislike my patches lately, almost
> always failing them; and usually on what at least seem to be unrelated
> test-cases. Any advice on how to deal with this?
Yeah, CI is snafu. I keep smashing retest until it gets through BAT
and then just double check the shard results to make sure nothing
relevant has tripped. If things look OK I recommend replying to the
result mail and provide a few short log snippets/other details on
what failed so that it's clear that it's irrelevant.
>
>
>
>
> >
> >>
> >> if ((IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv)) &&
> >> (mipi_config->pwm_blc == PPS_BLC_PMIC)) {
> >> - intel_dsi->gpio_panel =
> >> - gpiod_get(dev->dev, "panel", GPIOD_OUT_HIGH);
> >> -
> >> + intel_dsi->gpio_panel = gpiod_get(dev->dev, "panel", flags);
> >> if (IS_ERR(intel_dsi->gpio_panel)) {
> >> DRM_ERROR("Failed to own gpio for panel control\n");
> >> intel_dsi->gpio_panel = NULL;
> >> diff --git a/drivers/gpu/drm/i915/display/vlv_dsi.c b/drivers/gpu/drm/i915/display/vlv_dsi.c
> >> index 178d0fffba5b..e86e4a11e199 100644
> >> --- a/drivers/gpu/drm/i915/display/vlv_dsi.c
> >> +++ b/drivers/gpu/drm/i915/display/vlv_dsi.c
> >> @@ -1910,7 +1910,7 @@ void vlv_dsi_init(struct drm_i915_private *dev_priv)
> >>
> >> vlv_dphy_param_init(intel_dsi);
> >>
> >> - intel_dsi_vbt_gpio_init(intel_dsi);
> >> + intel_dsi_vbt_gpio_init(intel_dsi, current_mode != NULL);
> >>
> >> drm_connector_init(dev, connector, &intel_dsi_connector_funcs,
> >> DRM_MODE_CONNECTOR_DSI);
> >> --
> >> 2.23.0
> >
--
Ville Syrjälä
Intel
next prev parent reply other threads:[~2019-12-16 14:14 UTC|newest]
Thread overview: 28+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-12-15 16:38 [PATCH 0/5] drm/i915/dsi: Control panel and backlight enable GPIOs from VBT Hans de Goede
2019-12-15 16:38 ` [PATCH 1/5] pinctrl: Export pinctrl_unregister_mappings Hans de Goede
2019-12-15 16:38 ` [PATCH 2/5] drm/i915/dsi: Move poking of panel-enable GPIO to intel_dsi_vbt.c Hans de Goede
2019-12-16 10:27 ` Linus Walleij
2019-12-16 13:51 ` Ville Syrjälä
2019-12-15 16:38 ` [PATCH 3/5] drm/i915/dsi: Init panel-enable GPIO to low when the LCD is initially off Hans de Goede
2019-12-16 10:28 ` Linus Walleij
2019-12-16 13:45 ` Ville Syrjälä
2019-12-16 13:51 ` Hans de Goede
2019-12-16 14:14 ` Ville Syrjälä [this message]
2019-12-16 14:59 ` Hans de Goede
2019-12-15 16:38 ` [PATCH 4/5] drm/i915/dsi: Move Crystal Cove PMIC panel GPIO lookup from mfd to the i915 driver Hans de Goede
2019-12-16 10:30 ` Linus Walleij
2019-12-16 12:16 ` Andy Shevchenko
2019-12-16 13:13 ` Hans de Goede
2019-12-16 13:56 ` Ville Syrjälä
2019-12-16 14:16 ` Hans de Goede
2019-12-15 16:38 ` [PATCH 5/5] drm/i915/dsi: Control panel and backlight enable GPIOs on BYT Hans de Goede
2019-12-16 10:29 ` Linus Walleij
2019-12-16 14:04 ` Ville Syrjälä
2019-12-16 14:28 ` Hans de Goede
2019-12-16 10:26 ` [PATCH 0/5] drm/i915/dsi: Control panel and backlight enable GPIOs from VBT Linus Walleij
2019-12-16 10:59 ` Hans de Goede
2019-12-16 11:11 ` Hans de Goede
2019-12-16 12:16 ` Linus Walleij
2019-12-16 13:25 ` Hans de Goede
2019-12-16 12:18 ` Andy Shevchenko
2019-12-16 16:10 ` Lee Jones
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191216141450.GU1208@intel.com \
--to=ville.syrjala@linux.intel.com \
--cc=dri-devel@lists.freedesktop.org \
--cc=hdegoede@redhat.com \
--cc=intel-gfx@lists.freedesktop.org \
--cc=jani.nikula@linux.intel.com \
--cc=joonas.lahtinen@linux.intel.com \
--cc=lee.jones@linaro.org \
--cc=linus.walleij@linaro.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=rodrigo.vivi@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).