[PATCH v10 0/5] mt8183 dpi supports dual edge and pin mode swap

[PATCH v10 0/5] mt8183 dpi supports dual edge and pin mode swap

[Jitao Shi]

Changes since v9:
 - rename pinctrl-names = "gpiomode", "dpimode" to "active", "idle".
 - fix some typo.

Changes since v8:
 - drop pclk-sample redefine in mediatek,dpi.txt
 - only get the gpiomode and dpimode when dpi->pinctrl is successful.

Changes since v7:
 - separate dt-bindings to independent patches.
 - move dpi dual edge to one patch.

Changes since v6:
 - change dual_edge to pclk-sample
 - remove dpi_pin_mode_swap and

Changes since v5:
 - fine tune the dt-bindings commit message.

Changes since v4:
 - move pin mode control and dual edge control to deveice tree.
 - update dt-bindings document for pin mode swap and dual edge control.

Changes since v3:
 - add dpi pin mode control when dpi on or off.
 - update dpi dual edge comment.

Changes since v2:
 - update dt-bindings document for mt8183 dpi.
 - separate dual edge modfication as independent patch.

Jitao Shi (5):
  dt-bindings: media: add pclk-sample dual edge property
  dt-bindings: display: mediatek: control dpi pins mode to avoid leakage
  dt-bindings: display: mediatek: dpi sample data in dual edge support
  drm/mediatek: dpi sample mode support
  drm/mediatek: set dpi pin mode to gpio low to avoid leakage current

 .../display/mediatek/mediatek,dpi.txt         |  9 ++++
 .../bindings/media/video-interfaces.txt       |  4 +-
 drivers/gpu/drm/mediatek/mtk_dpi.c            | 49 ++++++++++++++++++-
 3 files changed, 58 insertions(+), 4 deletions(-)

-- 
2.21.0

[PATCH v10 1/5] dt-bindings: media: add pclk-sample dual edge property

[Jitao Shi]

Some chips's sample mode are rising, falling and dual edge (both
falling and rising edge).
Extern the pclk-sample property to support dual edge.

Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
---
 Documentation/devicetree/bindings/media/video-interfaces.txt | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/media/video-interfaces.txt b/Documentation/devicetree/bindings/media/video-interfaces.txt
index f884ada0bffc..da9ad24935db 100644
--- a/Documentation/devicetree/bindings/media/video-interfaces.txt
+++ b/Documentation/devicetree/bindings/media/video-interfaces.txt
@@ -118,8 +118,8 @@ Optional endpoint properties
 - data-enable-active: similar to HSYNC and VSYNC, specifies the data enable
   signal polarity.
 - field-even-active: field signal level during the even field data transmission.
-- pclk-sample: sample data on rising (1) or falling (0) edge of the pixel clock
-  signal.
+- pclk-sample: sample data on rising (1), falling (0) or both rising and
+  falling (2) edge of the pixel clock signal.
 - sync-on-green-active: active state of Sync-on-green (SoG) signal, 0/1 for
   LOW/HIGH respectively.
 - data-lanes: an array of physical data lane indexes. Position of an entry
-- 
2.21.0

[PATCH v10 2/5] dt-bindings: display: mediatek: control dpi pins mode to avoid leakage

[Jitao Shi]

Add property "pinctrl-names" to swap pin mode between gpio and dpi mode. Set
the dpi pins to gpio mode and output-low to avoid leakage current when dpi
disabled.

Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
---
 .../devicetree/bindings/display/mediatek/mediatek,dpi.txt  | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
index 58914cf681b8..77ca32a32399 100644
--- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
+++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
@@ -17,6 +17,10 @@ Required properties:
   Documentation/devicetree/bindings/graph.txt. This port should be connected
   to the input port of an attached HDMI or LVDS encoder chip.
 
+Optional properties:
+- pinctrl-names: Contain "gpiomode" and "dpimode".
+  pinctrl-names see Documentation/devicetree/bindings/pinctrlpinctrl-bindings.txt
+
 Example:
 
 dpi0: dpi@1401d000 {
@@ -27,6 +31,9 @@ dpi0: dpi@1401d000 {
 		 <&mmsys CLK_MM_DPI_ENGINE>,
 		 <&apmixedsys CLK_APMIXED_TVDPLL>;
 	clock-names = "pixel", "engine", "pll";
+	pinctrl-names = "active", "idle";
+	pinctrl-0 = <&dpi_pin_func>;
+	pinctrl-1 = <&dpi_pin_idle>;
 
 	port {
 		dpi0_out: endpoint {
-- 
2.21.0

[PATCH v10 3/5] dt-bindings: display: mediatek: dpi sample data in dual edge support

[Jitao Shi]

Add property "pclk-sample" to config the dpi sample on falling (0),
rising (1), both falling and rising (2).

Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
---
 .../devicetree/bindings/display/mediatek/mediatek,dpi.txt     | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
index 77ca32a32399..4eeead1d39db 100644
--- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
+++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
@@ -19,7 +19,8 @@ Required properties:
 
 Optional properties:
 - pinctrl-names: Contain "gpiomode" and "dpimode".
-  pinctrl-names see Documentation/devicetree/bindings/pinctrlpinctrl-bindings.txt
+  pinctrl-names see Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+- pclk-sample: refer Documentation/devicetree/bindings/media/video-interfaces.txt.
 
 Example:
 
@@ -37,6 +38,7 @@ dpi0: dpi@1401d000 {
 
 	port {
 		dpi0_out: endpoint {
+			pclk-sample = <0>;
 			remote-endpoint = <&hdmi0_in>;
 		};
 	};
-- 
2.21.0

[PATCH v10 4/5] drm/mediatek: dpi sample mode support

[Jitao Shi]

DPI can sample on falling, rising or both edge.
When DPI sample the data both rising and falling edge.
It can reduce half data io pins.

Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
---
 drivers/gpu/drm/mediatek/mtk_dpi.c | 18 ++++++++++++++++--
 1 file changed, 16 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c b/drivers/gpu/drm/mediatek/mtk_dpi.c
index 087f5ce732e1..db3272f7a4c4 100644
--- a/drivers/gpu/drm/mediatek/mtk_dpi.c
+++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
@@ -75,6 +75,7 @@ struct mtk_dpi {
 	enum mtk_dpi_out_bit_num bit_num;
 	enum mtk_dpi_out_channel_swap channel_swap;
 	int refcount;
+	u32 pclk_sample;
 };
 
 static inline struct mtk_dpi *mtk_dpi_from_encoder(struct drm_encoder *e)
@@ -348,6 +349,13 @@ static void mtk_dpi_config_disable_edge(struct mtk_dpi *dpi)
 		mtk_dpi_mask(dpi, dpi->conf->reg_h_fre_con, 0, EDGE_SEL_EN);
 }
 
+static void mtk_dpi_enable_pclk_sample_dual_edge(struct mtk_dpi *dpi)
+{
+	mtk_dpi_mask(dpi, DPI_DDR_SETTING, DDR_EN | DDR_4PHASE,
+		     DDR_EN | DDR_4PHASE);
+	mtk_dpi_mask(dpi, DPI_OUTPUT_SETTING, EDGE_SEL, EDGE_SEL);
+}
+
 static void mtk_dpi_config_color_format(struct mtk_dpi *dpi,
 					enum mtk_dpi_out_color_format format)
 {
@@ -439,7 +447,8 @@ static int mtk_dpi_set_display_mode(struct mtk_dpi *dpi,
 	pll_rate = clk_get_rate(dpi->tvd_clk);
 
 	vm.pixelclock = pll_rate / factor;
-	clk_set_rate(dpi->pixel_clk, vm.pixelclock);
+	clk_set_rate(dpi->pixel_clk,
+		     vm.pixelclock * (dpi->pclk_sample > 1 ? 2 : 1));
 	vm.pixelclock = clk_get_rate(dpi->pixel_clk);
 
 	dev_dbg(dpi->dev, "Got  PLL %lu Hz, pixel clock %lu Hz\n",
@@ -450,7 +459,8 @@ static int mtk_dpi_set_display_mode(struct mtk_dpi *dpi,
 	limit.y_bottom = 0x0010;
 	limit.y_top = 0x0FE0;
 
-	dpi_pol.ck_pol = MTK_DPI_POLARITY_FALLING;
+	dpi_pol.ck_pol = dpi->pclk_sample == 1 ?
+			 MTK_DPI_POLARITY_RISING : MTK_DPI_POLARITY_FALLING;
 	dpi_pol.de_pol = MTK_DPI_POLARITY_RISING;
 	dpi_pol.hsync_pol = vm.flags & DISPLAY_FLAGS_HSYNC_HIGH ?
 			    MTK_DPI_POLARITY_FALLING : MTK_DPI_POLARITY_RISING;
@@ -504,6 +514,8 @@ static int mtk_dpi_set_display_mode(struct mtk_dpi *dpi,
 	mtk_dpi_config_color_format(dpi, dpi->color_format);
 	mtk_dpi_config_2n_h_fre(dpi);
 	mtk_dpi_config_disable_edge(dpi);
+	if (dpi->pclk_sample > 1)
+		mtk_dpi_enable_pclk_sample_dual_edge(dpi);
 	mtk_dpi_sw_reset(dpi, false);
 
 	return 0;
@@ -704,6 +716,8 @@ static int mtk_dpi_probe(struct platform_device *pdev)
 
 	dpi->dev = dev;
 	dpi->conf = (struct mtk_dpi_conf *)of_device_get_match_data(dev);
+	of_property_read_u32_index(dev->of_node, "pclk-sample", 1,
+				   &dpi->pclk_sample);
 
 	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	dpi->regs = devm_ioremap_resource(dev, mem);
-- 
2.21.0

[PATCH v10 5/5] drm/mediatek: set dpi pin mode to gpio low to avoid leakage current

[Jitao Shi]

Config dpi pins mode to output and pull low when dpi is disabled.
Aovid leakage current from some dpi pins (Hsync Vsync DE ... ).

Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
---
 drivers/gpu/drm/mediatek/mtk_dpi.c | 31 ++++++++++++++++++++++++++++++
 1 file changed, 31 insertions(+)

diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c b/drivers/gpu/drm/mediatek/mtk_dpi.c
index db3272f7a4c4..0133ad8f6a7d 100644
--- a/drivers/gpu/drm/mediatek/mtk_dpi.c
+++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
@@ -10,7 +10,9 @@
 #include <linux/kernel.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
+#include <linux/of_gpio.h>
 #include <linux/of_graph.h>
+#include <linux/pinctrl/consumer.h>
 #include <linux/platform_device.h>
 #include <linux/types.h>
 
@@ -74,6 +76,9 @@ struct mtk_dpi {
 	enum mtk_dpi_out_yc_map yc_map;
 	enum mtk_dpi_out_bit_num bit_num;
 	enum mtk_dpi_out_channel_swap channel_swap;
+	struct pinctrl *pinctrl;
+	struct pinctrl_state *pins_gpio;
+	struct pinctrl_state *pins_dpi;
 	int refcount;
 	u32 pclk_sample;
 };
@@ -387,6 +392,9 @@ static void mtk_dpi_power_off(struct mtk_dpi *dpi)
 	if (--dpi->refcount != 0)
 		return;
 
+	if (dpi->pinctrl && dpi->pins_gpio)
+		pinctrl_select_state(dpi->pinctrl, dpi->pins_gpio);
+
 	mtk_dpi_disable(dpi);
 	clk_disable_unprepare(dpi->pixel_clk);
 	clk_disable_unprepare(dpi->engine_clk);
@@ -411,6 +419,9 @@ static int mtk_dpi_power_on(struct mtk_dpi *dpi)
 		goto err_pixel;
 	}
 
+	if (dpi->pinctrl && dpi->pins_dpi)
+		pinctrl_select_state(dpi->pinctrl, dpi->pins_dpi);
+
 	mtk_dpi_enable(dpi);
 	return 0;
 
@@ -719,6 +730,26 @@ static int mtk_dpi_probe(struct platform_device *pdev)
 	of_property_read_u32_index(dev->of_node, "pclk-sample", 1,
 				   &dpi->pclk_sample);
 
+	dpi->pinctrl = devm_pinctrl_get(&pdev->dev);
+	if (IS_ERR(dpi->pinctrl)) {
+		dpi->pinctrl = NULL;
+		dev_dbg(&pdev->dev, "Cannot find pinctrl!\n");
+	}
+	if (dpi->pinctrl) {
+		dpi->pins_gpio = pinctrl_lookup_state(dpi->pinctrl, "idle");
+		if (IS_ERR(dpi->pins_gpio)) {
+			dpi->pins_gpio = NULL;
+			dev_dbg(&pdev->dev, "Cannot find pinctrl idle!\n");
+		}
+		if (dpi->pins_gpio)
+			pinctrl_select_state(dpi->pinctrl, dpi->pins_gpio);
+
+		dpi->pins_dpi = pinctrl_lookup_state(dpi->pinctrl, "active");
+		if (IS_ERR(dpi->pins_dpi)) {
+			dpi->pins_dpi = NULL;
+			dev_dbg(&pdev->dev, "Cannot find pinctrl active!\n");
+		}
+	}
 	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	dpi->regs = devm_ioremap_resource(dev, mem);
 	if (IS_ERR(dpi->regs)) {
-- 
2.21.0

Re: [PATCH v10 2/5] dt-bindings: display: mediatek: control dpi pins mode to avoid leakage

[Sam Ravnborg]

Hi Jitao.

On Fri, Feb 28, 2020 at 01:21:25PM +0800, Jitao Shi wrote:
> Add property "pinctrl-names" to swap pin mode between gpio and dpi mode. Set
> the dpi pins to gpio mode and output-low to avoid leakage current when dpi
> disabled.
> 
> Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> ---
>  .../devicetree/bindings/display/mediatek/mediatek,dpi.txt  | 7 +++++++

When this has landed it would be great if you could follow-up with a
conversion to DT Schema of this file (.yaml).

	Sam

>  1 file changed, 7 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> index 58914cf681b8..77ca32a32399 100644
> --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> @@ -17,6 +17,10 @@ Required properties:
>    Documentation/devicetree/bindings/graph.txt. This port should be connected
>    to the input port of an attached HDMI or LVDS encoder chip.
>  
> +Optional properties:
> +- pinctrl-names: Contain "gpiomode" and "dpimode".
> +  pinctrl-names see Documentation/devicetree/bindings/pinctrlpinctrl-bindings.txt
> +
>  Example:
>  
>  dpi0: dpi@1401d000 {
> @@ -27,6 +31,9 @@ dpi0: dpi@1401d000 {
>  		 <&mmsys CLK_MM_DPI_ENGINE>,
>  		 <&apmixedsys CLK_APMIXED_TVDPLL>;
>  	clock-names = "pixel", "engine", "pll";
> +	pinctrl-names = "active", "idle";
> +	pinctrl-0 = <&dpi_pin_func>;
> +	pinctrl-1 = <&dpi_pin_idle>;
>  
>  	port {
>  		dpi0_out: endpoint {
> -- 
> 2.21.0
> _______________________________________________
> dri-devel mailing list
> dri-devel@lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/dri-devel