From: Sibi Sankar <sibis@codeaurora.org>
To: bjorn.andersson@linaro.org, mathieu.poirier@linaro.org,
jeffrey.l.hugo@gmail.com, luca@z3ntu.xyz
Cc: agross@kernel.org, ohad@wizery.com,
linux-arm-msm@vger.kernel.org, linux-remoteproc@vger.kernel.org,
linux-kernel@vger.kernel.org, Sibi Sankar <sibis@codeaurora.org>
Subject: [PATCH v4 2/3] remoteproc: qcom_q6v5_mss: Validate each segment during loading
Date: Thu, 5 Mar 2020 01:17:28 +0530 [thread overview]
Message-ID: <20200304194729.27979-3-sibis@codeaurora.org> (raw)
In-Reply-To: <20200304194729.27979-1-sibis@codeaurora.org>
From: Bjorn Andersson <bjorn.andersson@linaro.org>
The code used to sync with the MBA after each segment loaded and this is
still what's done downstream. So reduce the delta towards downstream by
switching to a model where the content is iteratively validated.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
---
V4:
* Filter redundant hyp_assign requests to prevent errors/warnings
* Dropping Jeff's and Luca's R-b/T-b due to minor changes
* Fix misc check patch errors
* Ignore two writel > 80 characters per line warnings as it affects
readability
drivers/remoteproc/qcom_q6v5_mss.c | 83 +++++++++++++++++++++---------
1 file changed, 58 insertions(+), 25 deletions(-)
diff --git a/drivers/remoteproc/qcom_q6v5_mss.c b/drivers/remoteproc/qcom_q6v5_mss.c
index 9fed1b1c203d3..b8a922181de8a 100644
--- a/drivers/remoteproc/qcom_q6v5_mss.c
+++ b/drivers/remoteproc/qcom_q6v5_mss.c
@@ -379,23 +379,33 @@ static void q6v5_pds_disable(struct q6v5 *qproc, struct device **pds,
}
static int q6v5_xfer_mem_ownership(struct q6v5 *qproc, int *current_perm,
- bool remote_owner, phys_addr_t addr,
+ bool local, bool remote, phys_addr_t addr,
size_t size)
{
- struct qcom_scm_vmperm next;
+ struct qcom_scm_vmperm next[2];
+ int perms = 0;
if (!qproc->need_mem_protection)
return 0;
- if (remote_owner && *current_perm == BIT(QCOM_SCM_VMID_MSS_MSA))
- return 0;
- if (!remote_owner && *current_perm == BIT(QCOM_SCM_VMID_HLOS))
+
+ if (local == !!(*current_perm & BIT(QCOM_SCM_VMID_HLOS)) &&
+ remote == !!(*current_perm & BIT(QCOM_SCM_VMID_MSS_MSA)))
return 0;
- next.vmid = remote_owner ? QCOM_SCM_VMID_MSS_MSA : QCOM_SCM_VMID_HLOS;
- next.perm = remote_owner ? QCOM_SCM_PERM_RW : QCOM_SCM_PERM_RWX;
+ if (local) {
+ next[perms].vmid = QCOM_SCM_VMID_HLOS;
+ next[perms].perm = QCOM_SCM_PERM_RWX;
+ perms++;
+ }
+
+ if (remote) {
+ next[perms].vmid = QCOM_SCM_VMID_MSS_MSA;
+ next[perms].perm = QCOM_SCM_PERM_RW;
+ perms++;
+ }
return qcom_scm_assign_mem(addr, ALIGN(size, SZ_4K),
- current_perm, &next, 1);
+ current_perm, next, perms);
}
static int q6v5_load(struct rproc *rproc, const struct firmware *fw)
@@ -801,7 +811,8 @@ static int q6v5_mpss_init_image(struct q6v5 *qproc, const struct firmware *fw)
/* Hypervisor mapping to access metadata by modem */
mdata_perm = BIT(QCOM_SCM_VMID_HLOS);
- ret = q6v5_xfer_mem_ownership(qproc, &mdata_perm, true, phys, size);
+ ret = q6v5_xfer_mem_ownership(qproc, &mdata_perm, false, true,
+ phys, size);
if (ret) {
dev_err(qproc->dev,
"assigning Q6 access to metadata failed: %d\n", ret);
@@ -819,7 +830,8 @@ static int q6v5_mpss_init_image(struct q6v5 *qproc, const struct firmware *fw)
dev_err(qproc->dev, "MPSS header authentication failed: %d\n", ret);
/* Metadata authentication done, remove modem access */
- xferop_ret = q6v5_xfer_mem_ownership(qproc, &mdata_perm, false, phys, size);
+ xferop_ret = q6v5_xfer_mem_ownership(qproc, &mdata_perm, true, false,
+ phys, size);
if (xferop_ret)
dev_warn(qproc->dev,
"mdt buffer not reclaimed system may become unstable\n");
@@ -906,7 +918,7 @@ static int q6v5_mba_load(struct q6v5 *qproc)
}
/* Assign MBA image access in DDR to q6 */
- ret = q6v5_xfer_mem_ownership(qproc, &qproc->mba_perm, true,
+ ret = q6v5_xfer_mem_ownership(qproc, &qproc->mba_perm, false, true,
qproc->mba_phys, qproc->mba_size);
if (ret) {
dev_err(qproc->dev,
@@ -943,8 +955,8 @@ static int q6v5_mba_load(struct q6v5 *qproc)
q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_nc);
reclaim_mba:
- xfermemop_ret = q6v5_xfer_mem_ownership(qproc, &qproc->mba_perm, false,
- qproc->mba_phys,
+ xfermemop_ret = q6v5_xfer_mem_ownership(qproc, &qproc->mba_perm, true,
+ false, qproc->mba_phys,
qproc->mba_size);
if (xfermemop_ret) {
dev_err(qproc->dev,
@@ -1014,7 +1026,7 @@ static void q6v5_mba_reclaim(struct q6v5 *qproc)
/* In case of failure or coredump scenario where reclaiming MBA memory
* could not happen reclaim it here.
*/
- ret = q6v5_xfer_mem_ownership(qproc, &qproc->mba_perm, false,
+ ret = q6v5_xfer_mem_ownership(qproc, &qproc->mba_perm, true, false,
qproc->mba_phys,
qproc->mba_size);
WARN_ON(ret);
@@ -1041,6 +1053,7 @@ static int q6v5_mpss_load(struct q6v5 *qproc)
phys_addr_t boot_addr;
phys_addr_t min_addr = PHYS_ADDR_MAX;
phys_addr_t max_addr = 0;
+ u32 code_length;
bool relocate = false;
char *fw_name;
size_t fw_name_len;
@@ -1095,9 +1108,19 @@ static int q6v5_mpss_load(struct q6v5 *qproc)
* memory can be reclaimed only after MBA is loaded. For modem cold
* boot this will be a nop
*/
- q6v5_xfer_mem_ownership(qproc, &qproc->mpss_perm, false,
+ q6v5_xfer_mem_ownership(qproc, &qproc->mpss_perm, true, false,
qproc->mpss_phys, qproc->mpss_size);
+ /* Share ownership between Linux and MSS, during segment loading */
+ ret = q6v5_xfer_mem_ownership(qproc, &qproc->mpss_perm, true, true,
+ qproc->mpss_phys, qproc->mpss_size);
+ if (ret) {
+ dev_err(qproc->dev,
+ "assigning Q6 access to mpss memory failed: %d\n", ret);
+ ret = -EAGAIN;
+ goto release_firmware;
+ }
+
mpss_reloc = relocate ? min_addr : qproc->mpss_phys;
qproc->mpss_reloc = mpss_reloc;
/* Load firmware segments */
@@ -1146,10 +1169,25 @@ static int q6v5_mpss_load(struct q6v5 *qproc)
phdr->p_memsz - phdr->p_filesz);
}
size += phdr->p_memsz;
+
+ code_length = readl(qproc->rmb_base + RMB_PMI_CODE_LENGTH_REG);
+ if (!code_length) {
+ boot_addr = relocate ? qproc->mpss_phys : min_addr;
+ writel(boot_addr, qproc->rmb_base + RMB_PMI_CODE_START_REG);
+ writel(RMB_CMD_LOAD_READY, qproc->rmb_base + RMB_MBA_COMMAND_REG);
+ }
+ writel(size, qproc->rmb_base + RMB_PMI_CODE_LENGTH_REG);
+
+ ret = readl(qproc->rmb_base + RMB_MBA_STATUS_REG);
+ if (ret < 0) {
+ dev_err(qproc->dev, "MPSS authentication failed: %d\n",
+ ret);
+ goto release_firmware;
+ }
}
/* Transfer ownership of modem ddr region to q6 */
- ret = q6v5_xfer_mem_ownership(qproc, &qproc->mpss_perm, true,
+ ret = q6v5_xfer_mem_ownership(qproc, &qproc->mpss_perm, false, true,
qproc->mpss_phys, qproc->mpss_size);
if (ret) {
dev_err(qproc->dev,
@@ -1158,11 +1196,6 @@ static int q6v5_mpss_load(struct q6v5 *qproc)
goto release_firmware;
}
- boot_addr = relocate ? qproc->mpss_phys : min_addr;
- writel(boot_addr, qproc->rmb_base + RMB_PMI_CODE_START_REG);
- writel(RMB_CMD_LOAD_READY, qproc->rmb_base + RMB_MBA_COMMAND_REG);
- writel(size, qproc->rmb_base + RMB_PMI_CODE_LENGTH_REG);
-
ret = q6v5_rmb_mba_wait(qproc, RMB_MBA_AUTH_COMPLETE, 10000);
if (ret == -ETIMEDOUT)
dev_err(qproc->dev, "MPSS authentication timed out\n");
@@ -1192,7 +1225,7 @@ static void qcom_q6v5_dump_segment(struct rproc *rproc,
if (!ret) {
/* Reset ownership back to Linux to copy segments */
ret = q6v5_xfer_mem_ownership(qproc, &qproc->mpss_perm,
- false,
+ true, false,
qproc->mpss_phys,
qproc->mpss_size);
}
@@ -1210,7 +1243,7 @@ static void qcom_q6v5_dump_segment(struct rproc *rproc,
if (qproc->dump_mba_loaded) {
/* Try to reset ownership back to Q6 */
q6v5_xfer_mem_ownership(qproc, &qproc->mpss_perm,
- true,
+ false, true,
qproc->mpss_phys,
qproc->mpss_size);
q6v5_mba_reclaim(qproc);
@@ -1240,8 +1273,8 @@ static int q6v5_start(struct rproc *rproc)
goto reclaim_mpss;
}
- xfermemop_ret = q6v5_xfer_mem_ownership(qproc, &qproc->mba_perm, false,
- qproc->mba_phys,
+ xfermemop_ret = q6v5_xfer_mem_ownership(qproc, &qproc->mba_perm, true,
+ false, qproc->mba_phys,
qproc->mba_size);
if (xfermemop_ret)
dev_err(qproc->dev,
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
next prev parent reply other threads:[~2020-03-04 19:48 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-03-04 19:47 [PATCH v4 0/3] remoteproc: mss: Improve mem_assign and firmware load Sibi Sankar
2020-03-04 19:47 ` [PATCH v4 1/3] remoteproc: qcom_q6v5_mss: Don't reassign mpss region on shutdown Sibi Sankar
2020-03-04 19:47 ` Sibi Sankar [this message]
2020-03-04 19:47 ` [PATCH v4 3/3] remoteproc: qcom_q6v5_mss: Reload the mba region on coredump Sibi Sankar
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200304194729.27979-3-sibis@codeaurora.org \
--to=sibis@codeaurora.org \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=jeffrey.l.hugo@gmail.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-remoteproc@vger.kernel.org \
--cc=luca@z3ntu.xyz \
--cc=mathieu.poirier@linaro.org \
--cc=ohad@wizery.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).