[PATCH 0/5] Enable Qualcomm QCS 404 HS/SS USB PHYs

[PATCH 0/5] Enable Qualcomm QCS 404 HS/SS USB PHYs

[Bryan O'Donoghue]

This set of patches does the following:

- Removes unused Qualcomm USB PHY bindings
- Adds new USB PHY bindings for QCS404
- Adds new USB PHY drivers for QCS404

These patches have been through seven review cycles already and have a
number of Review-by and Ack-by. For the pusposes of making it easier to
merge this set focuses on the PHY stuff in isolation.

The last set for can be found here:
https://lkml.org/lkml/2020/3/3/807

Jorge Ramirez-Ortiz (3):
  dt-bindings: phy: remove qcom-dwc3-usb-phy
  dt-bindings: Add Qualcomm USB SuperSpeed PHY bindings
  phy: qualcomm: usb: Add SuperSpeed PHY driver

Shawn Guo (1):
  phy: qualcomm: Add Synopsys 28nm Hi-Speed USB PHY driver

Sriharsha Allenki (1):
  dt-bindings: phy: Add Qualcomm Synopsys Hi-Speed USB PHY binding

 .../bindings/phy/qcom,usb-hs-28nm.yaml        |  90 ++++
 .../devicetree/bindings/phy/qcom,usb-ss.yaml  |  83 ++++
 .../bindings/phy/qcom-dwc3-usb-phy.txt        |  37 --
 drivers/phy/qualcomm/Kconfig                  |  20 +
 drivers/phy/qualcomm/Makefile                 |   2 +
 drivers/phy/qualcomm/phy-qcom-usb-hs-28nm.c   | 415 ++++++++++++++++++
 drivers/phy/qualcomm/phy-qcom-usb-ss.c        | 246 +++++++++++
 7 files changed, 856 insertions(+), 37 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/phy/qcom,usb-hs-28nm.yaml
 create mode 100644 Documentation/devicetree/bindings/phy/qcom,usb-ss.yaml
 delete mode 100644 Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt
 create mode 100644 drivers/phy/qualcomm/phy-qcom-usb-hs-28nm.c
 create mode 100644 drivers/phy/qualcomm/phy-qcom-usb-ss.c

-- 
2.25.1

[PATCH 1/5] dt-bindings: phy: remove qcom-dwc3-usb-phy

[Bryan O'Donoghue]

From: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>

This binding is not used by any driver.

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Cc: Jorge Ramirez-Ortiz <jorge.ramirez.ortiz@gmail.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 .../bindings/phy/qcom-dwc3-usb-phy.txt        | 37 -------------------
 1 file changed, 37 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt

diff --git a/Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt b/Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt
deleted file mode 100644
index a1697c27aecd..000000000000
--- a/Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt
+++ /dev/null
@@ -1,37 +0,0 @@
-Qualcomm DWC3 HS AND SS PHY CONTROLLER
---------------------------------------
-
-DWC3 PHY nodes are defined to describe on-chip Synopsis Physical layer
-controllers.  Each DWC3 PHY controller should have its own node.
-
-Required properties:
-- compatible: should contain one of the following:
-	- "qcom,dwc3-hs-usb-phy" for High Speed Synopsis PHY controller
-	- "qcom,dwc3-ss-usb-phy" for Super Speed Synopsis PHY controller
-- reg: offset and length of the DWC3 PHY controller register set
-- #phy-cells: must be zero
-- clocks: a list of phandles and clock-specifier pairs, one for each entry in
-  clock-names.
-- clock-names: Should contain "ref" for the PHY reference clock
-
-Optional clocks:
-  "xo"		External reference clock
-
-Example:
-		phy@100f8800 {
-			compatible = "qcom,dwc3-hs-usb-phy";
-			reg = <0x100f8800 0x30>;
-			clocks = <&gcc USB30_0_UTMI_CLK>;
-			clock-names = "ref";
-			#phy-cells = <0>;
-
-		};
-
-		phy@100f8830 {
-			compatible = "qcom,dwc3-ss-usb-phy";
-			reg = <0x100f8830 0x30>;
-			clocks = <&gcc USB30_0_MASTER_CLK>;
-			clock-names = "ref";
-			#phy-cells = <0>;
-
-		};
-- 
2.25.1

[PATCH 2/5] dt-bindings: phy: Add Qualcomm Synopsys Hi-Speed USB PHY binding

[Bryan O'Donoghue]

From: Sriharsha Allenki <sallenki@codeaurora.org>

Adds bindings for Qualcomm's 28 nm USB PHY supporting Low-Speed, Full-Speed
and Hi-Speed USB connectivity on Qualcomm chipsets.

[bod: Converted to YAML. Changed name dropping snps, 28nm components]

Signed-off-by: Sriharsha Allenki <sallenki@codeaurora.org>
Signed-off-by: Anu Ramanathan <anur@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Jorge Ramirez-Ortiz <jorge.ramirez.ortiz@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 .../bindings/phy/qcom,usb-hs-28nm.yaml        | 90 +++++++++++++++++++
 1 file changed, 90 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/qcom,usb-hs-28nm.yaml

diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-hs-28nm.yaml b/Documentation/devicetree/bindings/phy/qcom,usb-hs-28nm.yaml
new file mode 100644
index 000000000000..ca6a0836b53c
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom,usb-hs-28nm.yaml
@@ -0,0 +1,90 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/phy/qcom,usb-hs-28nm.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Qualcomm Synopsys DesignWare Core 28nm High-Speed PHY
+
+maintainers:
+  - Bryan O'Donoghue <bryan.odonoghue@linaro.org>
+
+description: |
+  Qualcomm Low-Speed, Full-Speed, Hi-Speed 28nm USB PHY
+
+properties:
+  compatible:
+    enum:
+      - qcom,usb-hs-28nm-femtophy
+
+  reg:
+    maxItems: 1
+
+  "#phy-cells":
+    const: 0
+
+  clocks:
+    items:
+      - description: rpmcc ref clock
+      - description: PHY AHB clock
+      - description: Rentention clock
+
+  clock-names:
+    items:
+      - const: ref
+      - const: ahb
+      - const: sleep
+
+  resets:
+    items:
+      - description: PHY core reset
+      - description: POR reset
+
+  reset-names:
+    items:
+      - const: phy
+      - const: por
+
+  vdd-supply:
+    description: phandle to the regulator VDD supply node.
+
+  vdda1p8-supply:
+    description: phandle to the regulator 1.8V supply node.
+
+  vdda3p3-supply:
+    description: phandle to the regulator 3.3V supply node.
+
+required:
+  - compatible
+  - reg
+  - "#phy-cells"
+  - clocks
+  - clock-names
+  - resets
+  - reset-names
+  - vdd-supply
+  - vdda1p8-supply
+  - vdda3p3-supply
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,gcc-qcs404.h>
+    #include <dt-bindings/clock/qcom,rpmcc.h>
+    usb2_phy_prim: phy@7a000 {
+        compatible = "qcom,usb-hs-28nm-femtophy";
+        reg = <0x0007a000 0x200>;
+        #phy-cells = <0>;
+        clocks = <&rpmcc RPM_SMD_LN_BB_CLK>,
+                 <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>,
+                 <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
+        clock-names = "ref", "ahb", "sleep";
+        resets = <&gcc GCC_USB_HS_PHY_CFG_AHB_BCR>,
+                 <&gcc GCC_USB2A_PHY_BCR>;
+        reset-names = "phy", "por";
+        vdd-supply = <&vreg_l4_1p2>;
+        vdda1p8-supply = <&vreg_l5_1p8>;
+        vdda3p3-supply = <&vreg_l12_3p3>;
+    };
+...
-- 
2.25.1

[PATCH 3/5] phy: qualcomm: Add Synopsys 28nm Hi-Speed USB PHY driver

[Bryan O'Donoghue]

From: Shawn Guo <shawn.guo@linaro.org>

Adds Qualcomm 28nm Hi-Speed USB PHY driver support. This PHY is usually
paired with Synopsys DWC3 USB controllers on Qualcomm SoCs.

The PHY can come in two flavours femtoPHY or picoPHY. This commit adds
support for the femtoPHY with the possibility of extending to the picoPHY
with additional future commits. Both PHYs are on a 28 nanometer process
node.

[bod: Updated qcom_snps_hsphy_set_mode to match new method signature
      Added disjunct on mode > 0
      Removed regulator_set_voltage() in favour of setting floor in dts
      Removed 'snps' and from driver name
      Extended commit log to mention femtoPHY and picoPHY for future
      reference.]

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Jorge Ramirez-Ortiz <jorge.ramirez.ortiz@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 drivers/phy/qualcomm/Kconfig                |  11 +
 drivers/phy/qualcomm/Makefile               |   1 +
 drivers/phy/qualcomm/phy-qcom-usb-hs-28nm.c | 415 ++++++++++++++++++++
 3 files changed, 427 insertions(+)
 create mode 100644 drivers/phy/qualcomm/phy-qcom-usb-hs-28nm.c

diff --git a/drivers/phy/qualcomm/Kconfig b/drivers/phy/qualcomm/Kconfig
index e46824da29f6..9c56a7216f72 100644
--- a/drivers/phy/qualcomm/Kconfig
+++ b/drivers/phy/qualcomm/Kconfig
@@ -91,3 +91,14 @@ config PHY_QCOM_USB_HSIC
 	select GENERIC_PHY
 	help
 	  Support for the USB HSIC ULPI compliant PHY on QCOM chipsets.
+
+config PHY_QCOM_USB_HS_28NM
+	tristate "Qualcomm 28nm High-Speed PHY"
+	depends on ARCH_QCOM || COMPILE_TEST
+	depends on EXTCON || !EXTCON # if EXTCON=m, this cannot be built-in
+	select GENERIC_PHY
+	help
+	  Enable this to support the Qualcomm Synopsys DesignWare Core 28nm
+	  High-Speed PHY driver. This driver supports the Hi-Speed PHY which
+	  is usually paired with either the ChipIdea or Synopsys DWC3 USB
+	  IPs on MSM SOCs.
diff --git a/drivers/phy/qualcomm/Makefile b/drivers/phy/qualcomm/Makefile
index 283251d6a5d9..a4dab5329de0 100644
--- a/drivers/phy/qualcomm/Makefile
+++ b/drivers/phy/qualcomm/Makefile
@@ -10,3 +10,4 @@ obj-$(CONFIG_PHY_QCOM_UFS_14NM)		+= phy-qcom-ufs-qmp-14nm.o
 obj-$(CONFIG_PHY_QCOM_UFS_20NM)		+= phy-qcom-ufs-qmp-20nm.o
 obj-$(CONFIG_PHY_QCOM_USB_HS) 		+= phy-qcom-usb-hs.o
 obj-$(CONFIG_PHY_QCOM_USB_HSIC) 	+= phy-qcom-usb-hsic.o
+obj-$(CONFIG_PHY_QCOM_USB_HS_28NM)	+= phy-qcom-usb-hs-28nm.o
diff --git a/drivers/phy/qualcomm/phy-qcom-usb-hs-28nm.c b/drivers/phy/qualcomm/phy-qcom-usb-hs-28nm.c
new file mode 100644
index 000000000000..d998e65c89c8
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-usb-hs-28nm.c
@@ -0,0 +1,415 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2009-2018, Linux Foundation. All rights reserved.
+ * Copyright (c) 2018-2020, Linaro Limited
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_graph.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+
+/* PHY register and bit definitions */
+#define PHY_CTRL_COMMON0		0x078
+#define SIDDQ				BIT(2)
+#define PHY_IRQ_CMD			0x0d0
+#define PHY_INTR_MASK0			0x0d4
+#define PHY_INTR_CLEAR0			0x0dc
+#define DPDM_MASK			0x1e
+#define DP_1_0				BIT(4)
+#define DP_0_1				BIT(3)
+#define DM_1_0				BIT(2)
+#define DM_0_1				BIT(1)
+
+enum hsphy_voltage {
+	VOL_NONE,
+	VOL_MIN,
+	VOL_MAX,
+	VOL_NUM,
+};
+
+enum hsphy_vreg {
+	VDD,
+	VDDA_1P8,
+	VDDA_3P3,
+	VREG_NUM,
+};
+
+struct hsphy_init_seq {
+	int offset;
+	int val;
+	int delay;
+};
+
+struct hsphy_data {
+	const struct hsphy_init_seq *init_seq;
+	unsigned int init_seq_num;
+};
+
+struct hsphy_priv {
+	void __iomem *base;
+	struct clk_bulk_data *clks;
+	int num_clks;
+	struct reset_control *phy_reset;
+	struct reset_control *por_reset;
+	struct regulator_bulk_data vregs[VREG_NUM];
+	const struct hsphy_data *data;
+	enum phy_mode mode;
+};
+
+static int qcom_snps_hsphy_set_mode(struct phy *phy, enum phy_mode mode,
+				    int submode)
+{
+	struct hsphy_priv *priv = phy_get_drvdata(phy);
+
+	priv->mode = PHY_MODE_INVALID;
+
+	if (mode > 0)
+		priv->mode = mode;
+
+	return 0;
+}
+
+static void qcom_snps_hsphy_enable_hv_interrupts(struct hsphy_priv *priv)
+{
+	u32 val;
+
+	/* Clear any existing interrupts before enabling the interrupts */
+	val = readb(priv->base + PHY_INTR_CLEAR0);
+	val |= DPDM_MASK;
+	writeb(val, priv->base + PHY_INTR_CLEAR0);
+
+	writeb(0x0, priv->base + PHY_IRQ_CMD);
+	usleep_range(200, 220);
+	writeb(0x1, priv->base + PHY_IRQ_CMD);
+
+	/* Make sure the interrupts are cleared */
+	usleep_range(200, 220);
+
+	val = readb(priv->base + PHY_INTR_MASK0);
+	switch (priv->mode) {
+	case PHY_MODE_USB_HOST_HS:
+	case PHY_MODE_USB_HOST_FS:
+	case PHY_MODE_USB_DEVICE_HS:
+	case PHY_MODE_USB_DEVICE_FS:
+		val |= DP_1_0 | DM_0_1;
+		break;
+	case PHY_MODE_USB_HOST_LS:
+	case PHY_MODE_USB_DEVICE_LS:
+		val |= DP_0_1 | DM_1_0;
+		break;
+	default:
+		/* No device connected */
+		val |= DP_0_1 | DM_0_1;
+		break;
+	}
+	writeb(val, priv->base + PHY_INTR_MASK0);
+}
+
+static void qcom_snps_hsphy_disable_hv_interrupts(struct hsphy_priv *priv)
+{
+	u32 val;
+
+	val = readb(priv->base + PHY_INTR_MASK0);
+	val &= ~DPDM_MASK;
+	writeb(val, priv->base + PHY_INTR_MASK0);
+
+	/* Clear any pending interrupts */
+	val = readb(priv->base + PHY_INTR_CLEAR0);
+	val |= DPDM_MASK;
+	writeb(val, priv->base + PHY_INTR_CLEAR0);
+
+	writeb(0x0, priv->base + PHY_IRQ_CMD);
+	usleep_range(200, 220);
+
+	writeb(0x1, priv->base + PHY_IRQ_CMD);
+	usleep_range(200, 220);
+}
+
+static void qcom_snps_hsphy_enter_retention(struct hsphy_priv *priv)
+{
+	u32 val;
+
+	val = readb(priv->base + PHY_CTRL_COMMON0);
+	val |= SIDDQ;
+	writeb(val, priv->base + PHY_CTRL_COMMON0);
+}
+
+static void qcom_snps_hsphy_exit_retention(struct hsphy_priv *priv)
+{
+	u32 val;
+
+	val = readb(priv->base + PHY_CTRL_COMMON0);
+	val &= ~SIDDQ;
+	writeb(val, priv->base + PHY_CTRL_COMMON0);
+}
+
+static int qcom_snps_hsphy_power_on(struct phy *phy)
+{
+	struct hsphy_priv *priv = phy_get_drvdata(phy);
+	int ret;
+
+	ret = regulator_bulk_enable(VREG_NUM, priv->vregs);
+	if (ret)
+		return ret;
+	ret = clk_bulk_prepare_enable(priv->num_clks, priv->clks);
+	if (ret)
+		goto err_disable_regulator;
+	qcom_snps_hsphy_disable_hv_interrupts(priv);
+	qcom_snps_hsphy_exit_retention(priv);
+
+	return 0;
+
+err_disable_regulator:
+	regulator_bulk_disable(VREG_NUM, priv->vregs);
+
+	return ret;
+}
+
+static int qcom_snps_hsphy_power_off(struct phy *phy)
+{
+	struct hsphy_priv *priv = phy_get_drvdata(phy);
+
+	qcom_snps_hsphy_enter_retention(priv);
+	qcom_snps_hsphy_enable_hv_interrupts(priv);
+	clk_bulk_disable_unprepare(priv->num_clks, priv->clks);
+	regulator_bulk_disable(VREG_NUM, priv->vregs);
+
+	return 0;
+}
+
+static int qcom_snps_hsphy_reset(struct hsphy_priv *priv)
+{
+	int ret;
+
+	ret = reset_control_assert(priv->phy_reset);
+	if (ret)
+		return ret;
+
+	usleep_range(10, 15);
+
+	ret = reset_control_deassert(priv->phy_reset);
+	if (ret)
+		return ret;
+
+	usleep_range(80, 100);
+
+	return 0;
+}
+
+static void qcom_snps_hsphy_init_sequence(struct hsphy_priv *priv)
+{
+	const struct hsphy_data *data = priv->data;
+	const struct hsphy_init_seq *seq;
+	int i;
+
+	/* Device match data is optional. */
+	if (!data)
+		return;
+
+	seq = data->init_seq;
+
+	for (i = 0; i < data->init_seq_num; i++, seq++) {
+		writeb(seq->val, priv->base + seq->offset);
+		if (seq->delay)
+			usleep_range(seq->delay, seq->delay + 10);
+	}
+}
+
+static int qcom_snps_hsphy_por_reset(struct hsphy_priv *priv)
+{
+	int ret;
+
+	ret = reset_control_assert(priv->por_reset);
+	if (ret)
+		return ret;
+
+	/*
+	 * The Femto PHY is POR reset in the following scenarios.
+	 *
+	 * 1. After overriding the parameter registers.
+	 * 2. Low power mode exit from PHY retention.
+	 *
+	 * Ensure that SIDDQ is cleared before bringing the PHY
+	 * out of reset.
+	 */
+	qcom_snps_hsphy_exit_retention(priv);
+
+	/*
+	 * As per databook, 10 usec delay is required between
+	 * PHY POR assert and de-assert.
+	 */
+	usleep_range(10, 20);
+	ret = reset_control_deassert(priv->por_reset);
+	if (ret)
+		return ret;
+
+	/*
+	 * As per databook, it takes 75 usec for PHY to stabilize
+	 * after the reset.
+	 */
+	usleep_range(80, 100);
+
+	return 0;
+}
+
+static int qcom_snps_hsphy_init(struct phy *phy)
+{
+	struct hsphy_priv *priv = phy_get_drvdata(phy);
+	int ret;
+
+	ret = qcom_snps_hsphy_reset(priv);
+	if (ret)
+		return ret;
+
+	qcom_snps_hsphy_init_sequence(priv);
+
+	ret = qcom_snps_hsphy_por_reset(priv);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static const struct phy_ops qcom_snps_hsphy_ops = {
+	.init = qcom_snps_hsphy_init,
+	.power_on = qcom_snps_hsphy_power_on,
+	.power_off = qcom_snps_hsphy_power_off,
+	.set_mode = qcom_snps_hsphy_set_mode,
+	.owner = THIS_MODULE,
+};
+
+static const char * const qcom_snps_hsphy_clks[] = {
+	"ref",
+	"ahb",
+	"sleep",
+};
+
+static int qcom_snps_hsphy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct phy_provider *provider;
+	struct hsphy_priv *priv;
+	struct phy *phy;
+	int ret;
+	int i;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(priv->base))
+		return PTR_ERR(priv->base);
+
+	priv->num_clks = ARRAY_SIZE(qcom_snps_hsphy_clks);
+	priv->clks = devm_kcalloc(dev, priv->num_clks, sizeof(*priv->clks),
+				  GFP_KERNEL);
+	if (!priv->clks)
+		return -ENOMEM;
+
+	for (i = 0; i < priv->num_clks; i++)
+		priv->clks[i].id = qcom_snps_hsphy_clks[i];
+
+	ret = devm_clk_bulk_get(dev, priv->num_clks, priv->clks);
+	if (ret)
+		return ret;
+
+	priv->phy_reset = devm_reset_control_get_exclusive(dev, "phy");
+	if (IS_ERR(priv->phy_reset))
+		return PTR_ERR(priv->phy_reset);
+
+	priv->por_reset = devm_reset_control_get_exclusive(dev, "por");
+	if (IS_ERR(priv->por_reset))
+		return PTR_ERR(priv->por_reset);
+
+	priv->vregs[VDD].supply = "vdd";
+	priv->vregs[VDDA_1P8].supply = "vdda1p8";
+	priv->vregs[VDDA_3P3].supply = "vdda3p3";
+
+	ret = devm_regulator_bulk_get(dev, VREG_NUM, priv->vregs);
+	if (ret)
+		return ret;
+
+	/* Get device match data */
+	priv->data = device_get_match_data(dev);
+
+	phy = devm_phy_create(dev, dev->of_node, &qcom_snps_hsphy_ops);
+	if (IS_ERR(phy))
+		return PTR_ERR(phy);
+
+	phy_set_drvdata(phy, priv);
+
+	provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	if (IS_ERR(provider))
+		return PTR_ERR(provider);
+
+	ret = regulator_set_load(priv->vregs[VDDA_1P8].consumer, 19000);
+	if (ret < 0)
+		return ret;
+
+	ret = regulator_set_load(priv->vregs[VDDA_3P3].consumer, 16000);
+	if (ret < 0)
+		goto unset_1p8_load;
+
+	return 0;
+
+unset_1p8_load:
+	regulator_set_load(priv->vregs[VDDA_1P8].consumer, 0);
+
+	return ret;
+}
+
+/*
+ * The macro is used to define an initialization sequence.  Each tuple
+ * is meant to program 'value' into phy register at 'offset' with 'delay'
+ * in us followed.
+ */
+#define HSPHY_INIT_CFG(o, v, d)	{ .offset = o, .val = v, .delay = d, }
+
+static const struct hsphy_init_seq init_seq_femtophy[] = {
+	HSPHY_INIT_CFG(0xc0, 0x01, 0),
+	HSPHY_INIT_CFG(0xe8, 0x0d, 0),
+	HSPHY_INIT_CFG(0x74, 0x12, 0),
+	HSPHY_INIT_CFG(0x98, 0x63, 0),
+	HSPHY_INIT_CFG(0x9c, 0x03, 0),
+	HSPHY_INIT_CFG(0xa0, 0x1d, 0),
+	HSPHY_INIT_CFG(0xa4, 0x03, 0),
+	HSPHY_INIT_CFG(0x8c, 0x23, 0),
+	HSPHY_INIT_CFG(0x78, 0x08, 0),
+	HSPHY_INIT_CFG(0x7c, 0xdc, 0),
+	HSPHY_INIT_CFG(0x90, 0xe0, 20),
+	HSPHY_INIT_CFG(0x74, 0x10, 0),
+	HSPHY_INIT_CFG(0x90, 0x60, 0),
+};
+
+static const struct hsphy_data hsphy_data_femtophy = {
+	.init_seq = init_seq_femtophy,
+	.init_seq_num = ARRAY_SIZE(init_seq_femtophy),
+};
+
+static const struct of_device_id qcom_snps_hsphy_match[] = {
+	{ .compatible = "qcom,usb-hs-28nm-femtophy", .data = &hsphy_data_femtophy, },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, qcom_snps_hsphy_match);
+
+static struct platform_driver qcom_snps_hsphy_driver = {
+	.probe = qcom_snps_hsphy_probe,
+	.driver	= {
+		.name = "qcom,usb-hs-28nm-phy",
+		.of_match_table = qcom_snps_hsphy_match,
+	},
+};
+module_platform_driver(qcom_snps_hsphy_driver);
+
+MODULE_DESCRIPTION("Qualcomm 28nm Hi-Speed USB PHY driver");
+MODULE_LICENSE("GPL v2");
-- 
2.25.1

[PATCH 4/5] dt-bindings: Add Qualcomm USB SuperSpeed PHY bindings

[Bryan O'Donoghue]

From: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>

Binding description for Qualcomm's Synopsys 1.0.0 SuperSpeed PHY. This PHY
appears in a number of SoCs on various flavors of 20nm and 28nm nodes.

This commit adds information related to the 28nm node only.

Based on Sriharsha Allenki's <sallenki@codeaurora.org> original
definitions.

[bod: converted to yaml format]

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Cc: Jorge Ramirez-Ortiz <jorge.ramirez.ortiz@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Jorge Ramirez-Ortiz <jorge.ramirez.ortiz@gmail.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 .../devicetree/bindings/phy/qcom,usb-ss.yaml  | 83 +++++++++++++++++++
 1 file changed, 83 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/qcom,usb-ss.yaml

diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-ss.yaml b/Documentation/devicetree/bindings/phy/qcom,usb-ss.yaml
new file mode 100644
index 000000000000..bd1388d62ce0
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom,usb-ss.yaml
@@ -0,0 +1,83 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/phy/qcom,usb-ss.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Qualcomm Synopsys 1.0.0 SuperSpeed USB PHY
+
+maintainers:
+  - Bryan O'Donoghue <bryan.odonoghue@linaro.org>
+
+description: |
+  Qualcomm Synopsys 1.0.0 SuperSpeed USB PHY
+
+properties:
+  compatible:
+    enum:
+      - qcom,usb-ss-28nm-phy
+
+  reg:
+    maxItems: 1
+
+  "#phy-cells":
+    const: 0
+
+  clocks:
+    items:
+      - description: rpmcc clock
+      - description: PHY AHB clock
+      - description: SuperSpeed pipe clock
+
+  clock-names:
+    items:
+      - const: ref
+      - const: ahb
+      - const: pipe
+
+  vdd-supply:
+    description: phandle to the regulator VDD supply node.
+
+  vdda1p8-supply:
+    description: phandle to the regulator 1.8V supply node.
+
+  resets:
+    items:
+      - description: COM reset
+      - description: PHY reset line
+
+  reset-names:
+    items:
+      - const: com
+      - const: phy
+
+required:
+  - compatible
+  - reg
+  - "#phy-cells"
+  - clocks
+  - clock-names
+  - vdd-supply
+  - vdda1p8-supply
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,gcc-qcs404.h>
+    #include <dt-bindings/clock/qcom,rpmcc.h>
+    usb3_phy: usb3-phy@78000 {
+        compatible = "qcom,usb-ss-28nm-phy";
+        reg = <0x78000 0x400>;
+        #phy-cells = <0>;
+        clocks = <&rpmcc RPM_SMD_LN_BB_CLK>,
+                 <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>,
+                 <&gcc GCC_USB3_PHY_PIPE_CLK>;
+        clock-names = "ref", "ahb", "pipe";
+        resets = <&gcc GCC_USB3_PHY_BCR>,
+                 <&gcc GCC_USB3PHY_PHY_BCR>;
+        reset-names = "com", "phy";
+        vdd-supply = <&vreg_l3_1p05>;
+        vdda1p8-supply = <&vreg_l5_1p8>;
+    };
+...
-- 
2.25.1

[PATCH 5/5] phy: qualcomm: usb: Add SuperSpeed PHY driver

[Bryan O'Donoghue]

From: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>

Controls Qualcomm's SS PHY 1.0.0 implemented on various SoCs on both the
20nm and 28nm process nodes.

Based on Sriharsha Allenki's <sallenki@codeaurora.org> original code.

[bod: Removed dependency on extcon.
      Switched to gpio-usb-conn to handle VBUS On/Off
      Switched to usb-role-switch to bind gpio-usb-conn to DWC3]
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Cc: Jorge Ramirez-Ortiz <jorge.ramirez.ortiz@gmail.com>
Cc: Sriharsha Allenki's <sallenki@codeaurora.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 drivers/phy/qualcomm/Kconfig           |   9 +
 drivers/phy/qualcomm/Makefile          |   1 +
 drivers/phy/qualcomm/phy-qcom-usb-ss.c | 246 +++++++++++++++++++++++++
 3 files changed, 256 insertions(+)
 create mode 100644 drivers/phy/qualcomm/phy-qcom-usb-ss.c

diff --git a/drivers/phy/qualcomm/Kconfig b/drivers/phy/qualcomm/Kconfig
index 9c56a7216f72..98674ed094d9 100644
--- a/drivers/phy/qualcomm/Kconfig
+++ b/drivers/phy/qualcomm/Kconfig
@@ -102,3 +102,12 @@ config PHY_QCOM_USB_HS_28NM
 	  High-Speed PHY driver. This driver supports the Hi-Speed PHY which
 	  is usually paired with either the ChipIdea or Synopsys DWC3 USB
 	  IPs on MSM SOCs.
+
+config PHY_QCOM_USB_SS
+	tristate "Qualcomm USB Super-Speed PHY driver"
+	depends on ARCH_QCOM || COMPILE_TEST
+	depends on EXTCON || !EXTCON # if EXTCON=m, this cannot be built-in
+	select GENERIC_PHY
+	help
+	  Enable this to support the Super-Speed USB transceiver on various
+	  Qualcomm chipsets.
diff --git a/drivers/phy/qualcomm/Makefile b/drivers/phy/qualcomm/Makefile
index a4dab5329de0..1f14aeacbd70 100644
--- a/drivers/phy/qualcomm/Makefile
+++ b/drivers/phy/qualcomm/Makefile
@@ -11,3 +11,4 @@ obj-$(CONFIG_PHY_QCOM_UFS_20NM)		+= phy-qcom-ufs-qmp-20nm.o
 obj-$(CONFIG_PHY_QCOM_USB_HS) 		+= phy-qcom-usb-hs.o
 obj-$(CONFIG_PHY_QCOM_USB_HSIC) 	+= phy-qcom-usb-hsic.o
 obj-$(CONFIG_PHY_QCOM_USB_HS_28NM)	+= phy-qcom-usb-hs-28nm.o
+obj-$(CONFIG_PHY_QCOM_USB_SS)		+= phy-qcom-usb-ss.o
diff --git a/drivers/phy/qualcomm/phy-qcom-usb-ss.c b/drivers/phy/qualcomm/phy-qcom-usb-ss.c
new file mode 100644
index 000000000000..a3a6d3ce7ea1
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-usb-ss.c
@@ -0,0 +1,246 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2012-2014,2017 The Linux Foundation. All rights reserved.
+ * Copyright (c) 2018-2020, Linaro Limited
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+
+#define PHY_CTRL0			0x6C
+#define PHY_CTRL1			0x70
+#define PHY_CTRL2			0x74
+#define PHY_CTRL4			0x7C
+
+/* PHY_CTRL bits */
+#define REF_PHY_EN			BIT(0)
+#define LANE0_PWR_ON			BIT(2)
+#define SWI_PCS_CLK_SEL			BIT(4)
+#define TST_PWR_DOWN			BIT(4)
+#define PHY_RESET			BIT(7)
+
+#define NUM_BULK_CLKS			3
+#define NUM_BULK_REGS			2
+
+struct ssphy_priv {
+	void __iomem *base;
+	struct device *dev;
+	struct reset_control *reset_com;
+	struct reset_control *reset_phy;
+	struct regulator_bulk_data regs[NUM_BULK_REGS];
+	struct clk_bulk_data clks[NUM_BULK_CLKS];
+	enum phy_mode mode;
+};
+
+static inline void qcom_ssphy_updatel(void __iomem *addr, u32 mask, u32 val)
+{
+	writel((readl(addr) & ~mask) | val, addr);
+}
+
+static int qcom_ssphy_do_reset(struct ssphy_priv *priv)
+{
+	int ret;
+
+	if (!priv->reset_com) {
+		qcom_ssphy_updatel(priv->base + PHY_CTRL1, PHY_RESET,
+				   PHY_RESET);
+		usleep_range(10, 20);
+		qcom_ssphy_updatel(priv->base + PHY_CTRL1, PHY_RESET, 0);
+	} else {
+		ret = reset_control_assert(priv->reset_com);
+		if (ret) {
+			dev_err(priv->dev, "Failed to assert reset com\n");
+			return ret;
+		}
+
+		ret = reset_control_assert(priv->reset_phy);
+		if (ret) {
+			dev_err(priv->dev, "Failed to assert reset phy\n");
+			return ret;
+		}
+
+		usleep_range(10, 20);
+
+		ret = reset_control_deassert(priv->reset_com);
+		if (ret) {
+			dev_err(priv->dev, "Failed to deassert reset com\n");
+			return ret;
+		}
+
+		ret = reset_control_deassert(priv->reset_phy);
+		if (ret) {
+			dev_err(priv->dev, "Failed to deassert reset phy\n");
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static int qcom_ssphy_power_on(struct phy *phy)
+{
+	struct ssphy_priv *priv = phy_get_drvdata(phy);
+	int ret;
+
+	ret = regulator_bulk_enable(NUM_BULK_REGS, priv->regs);
+	if (ret)
+		return ret;
+
+	ret = clk_bulk_prepare_enable(NUM_BULK_CLKS, priv->clks);
+	if (ret)
+		goto err_disable_regulator;
+
+	ret = qcom_ssphy_do_reset(priv);
+	if (ret)
+		goto err_disable_clock;
+
+	writeb(SWI_PCS_CLK_SEL, priv->base + PHY_CTRL0);
+	qcom_ssphy_updatel(priv->base + PHY_CTRL4, LANE0_PWR_ON, LANE0_PWR_ON);
+	qcom_ssphy_updatel(priv->base + PHY_CTRL2, REF_PHY_EN, REF_PHY_EN);
+	qcom_ssphy_updatel(priv->base + PHY_CTRL4, TST_PWR_DOWN, 0);
+
+	return 0;
+err_disable_clock:
+	clk_bulk_disable_unprepare(NUM_BULK_CLKS, priv->clks);
+err_disable_regulator:
+	regulator_bulk_disable(NUM_BULK_REGS, priv->regs);
+
+	return ret;
+}
+
+static int qcom_ssphy_power_off(struct phy *phy)
+{
+	struct ssphy_priv *priv = phy_get_drvdata(phy);
+
+	qcom_ssphy_updatel(priv->base + PHY_CTRL4, LANE0_PWR_ON, 0);
+	qcom_ssphy_updatel(priv->base + PHY_CTRL2, REF_PHY_EN, 0);
+	qcom_ssphy_updatel(priv->base + PHY_CTRL4, TST_PWR_DOWN, TST_PWR_DOWN);
+
+	clk_bulk_disable_unprepare(NUM_BULK_CLKS, priv->clks);
+	regulator_bulk_disable(NUM_BULK_REGS, priv->regs);
+
+	return 0;
+}
+
+static int qcom_ssphy_init_clock(struct ssphy_priv *priv)
+{
+	priv->clks[0].id = "ref";
+	priv->clks[1].id = "ahb";
+	priv->clks[2].id = "pipe";
+
+	return devm_clk_bulk_get(priv->dev, NUM_BULK_CLKS, priv->clks);
+}
+
+static int qcom_ssphy_init_regulator(struct ssphy_priv *priv)
+{
+	int ret;
+
+	priv->regs[0].supply = "vdd";
+	priv->regs[1].supply = "vdda1p8";
+	ret = devm_regulator_bulk_get(priv->dev, NUM_BULK_REGS, priv->regs);
+	if (ret) {
+		if (ret != -EPROBE_DEFER)
+			dev_err(priv->dev, "Failed to get regulators\n");
+		return ret;
+	}
+
+	return ret;
+}
+
+static int qcom_ssphy_init_reset(struct ssphy_priv *priv)
+{
+	priv->reset_com = devm_reset_control_get_optional_exclusive(priv->dev, "com");
+	if (IS_ERR(priv->reset_com)) {
+		dev_err(priv->dev, "Failed to get reset control com\n");
+		return PTR_ERR(priv->reset_com);
+	}
+
+	if (priv->reset_com) {
+		/* if reset_com is present, reset_phy is no longer optional */
+		priv->reset_phy = devm_reset_control_get_exclusive(priv->dev, "phy");
+		if (IS_ERR(priv->reset_phy)) {
+			dev_err(priv->dev, "Failed to get reset control phy\n");
+			return PTR_ERR(priv->reset_phy);
+		}
+	}
+
+	return 0;
+}
+
+static const struct phy_ops qcom_ssphy_ops = {
+	.power_off = qcom_ssphy_power_off,
+	.power_on = qcom_ssphy_power_on,
+	.owner = THIS_MODULE,
+};
+
+static int qcom_ssphy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct phy_provider *provider;
+	struct ssphy_priv *priv;
+	struct phy *phy;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(struct ssphy_priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->dev = dev;
+	priv->mode = PHY_MODE_INVALID;
+
+	priv->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(priv->base))
+		return PTR_ERR(priv->base);
+
+	ret = qcom_ssphy_init_clock(priv);
+	if (ret)
+		return ret;
+
+	ret = qcom_ssphy_init_reset(priv);
+	if (ret)
+		return ret;
+
+	ret = qcom_ssphy_init_regulator(priv);
+	if (ret)
+		return ret;
+
+	phy = devm_phy_create(dev, dev->of_node, &qcom_ssphy_ops);
+	if (IS_ERR(phy)) {
+		dev_err(dev, "Failed to create the SS phy\n");
+		return PTR_ERR(phy);
+	}
+
+	phy_set_drvdata(phy, priv);
+
+	provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+	return PTR_ERR_OR_ZERO(provider);
+}
+
+static const struct of_device_id qcom_ssphy_match[] = {
+	{ .compatible = "qcom,usb-ss-28nm-phy", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, qcom_ssphy_match);
+
+static struct platform_driver qcom_ssphy_driver = {
+	.probe		= qcom_ssphy_probe,
+	.driver = {
+		.name	= "qcom-usb-ssphy",
+		.of_match_table = qcom_ssphy_match,
+	},
+};
+module_platform_driver(qcom_ssphy_driver);
+
+MODULE_DESCRIPTION("Qualcomm SuperSpeed USB PHY driver");
+MODULE_LICENSE("GPL v2");
-- 
2.25.1