From: Oleksij Rempel <o.rempel@pengutronix.de>
To: Mark Rutland <mark.rutland@arm.com>,
Rob Herring <robh+dt@kernel.org>,
Sascha Hauer <s.hauer@pengutronix.de>,
Shawn Guo <shawnguo@kernel.org>
Cc: David Jander <david@protonic.nl>,
Oleksij Rempel <o.rempel@pengutronix.de>,
devicetree@vger.kernel.org, Fabio Estevam <festevam@gmail.com>,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, NXP Linux Team <linux-imx@nxp.com>,
Pengutronix Kernel Team <kernel@pengutronix.de>
Subject: [PATCH v1 5/6] ARM: dts: add Protonic RVT board
Date: Wed, 18 Mar 2020 13:03:53 +0100 [thread overview]
Message-ID: <20200318120354.4989-5-o.rempel@pengutronix.de> (raw)
In-Reply-To: <20200318120354.4989-1-o.rempel@pengutronix.de>
From: David Jander <david@protonic.nl>
Protonic RVT is an internal development platform for a wireless ISObus
Virtual Terminal based on COTS tablets, and the predecessor of the WD2
platform.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
.../devicetree/bindings/arm/fsl.yaml | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-prtrvt.dts | 108 ++++++++++++++++++
3 files changed, 110 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-prtrvt.dts
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 424be1edf005..2e8a03ef5c95 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -168,6 +168,7 @@ properties:
- emtrion,emcon-mx6-avari # emCON-MX6S or emCON-MX6DL SoM on Avari Base
- fsl,imx6dl-sabreauto # i.MX6 DualLite/Solo SABRE Automotive Board
- fsl,imx6dl-sabresd # i.MX6 DualLite SABRE Smart Device Board
+ - prt,prtrvt # Protonic RVT board
- prt,prtvt7 # Protonic VT7 board
- technologic,imx6dl-ts4900
- technologic,imx6dl-ts7970
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e53abe1de259..afaccc9bc645 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -446,6 +446,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-nitrogen6x.dtb \
imx6dl-phytec-mira-rdk-nand.dtb \
imx6dl-phytec-pbab01.dtb \
+ imx6dl-prtrvt.dtb \
imx6dl-prtvt7.dtb \
imx6dl-rex-basic.dtb \
imx6dl-riotboard.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-prtrvt.dts b/arch/arm/boot/dts/imx6dl-prtrvt.dts
new file mode 100644
index 000000000000..fddc91b5a113
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-prtrvt.dts
@@ -0,0 +1,108 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-prti6q.dtsi"
+
+/ {
+ model = "Protonic RVT board";
+ compatible = "prt,prtrvt", "fsl,imx6dl";
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x10000000>;
+ };
+};
+
+&iomuxc {
+ prti6q {
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ /* SGTL5000 sys_mclk */
+ MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
+ /* CAN1_SR + CAN2_SR GPIO outputs */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
+ MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13070
+
+ /* CAN1_TERM */
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
+ /* ITU656_nRESET */
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
+
+ /* HW revision detect */
+ /* REV_ID0 */
+ MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0
+ /* REV_ID1 */
+ MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0
+ /* REV_ID2 */
+ MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0
+ /* REV_ID3 */
+ MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b0
+ /* REV_ID4 */
+ MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x1b0b0
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ /* DEBUG0 */
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ /* Not connected */
+ MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
+ /* power enable, high active */
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
+ >;
+ };
+ };
+};
+
+&i2c3 {
+ rtc: pcf8563@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&pwm1 {
+ status = "disabled";
+};
+
+&ssi1 {
+ status = "disabled";
+};
+
+&uart2 {
+ status = "disabled";
+};
+
+&uart5 {
+ status = "disabled";
+};
+
+&usbh1 {
+ status = "disabled";
+};
+
+&can2 {
+ status = "disabled";
+};
+
+&vpu {
+ status = "disabled";
+};
+
+&audmux {
+ status = "disabled";
+};
+
+&ipu1 {
+ status = "disabled";
+};
--
2.25.1
next prev parent reply other threads:[~2020-03-18 12:04 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-03-18 12:03 [PATCH v1 1/6] dt-bindings: vendor-prefixes: Add an entry for Protonic Holland Oleksij Rempel
2020-03-18 12:03 ` [PATCH v1 2/6] ARM: dts: add Protonic PRTI6Q board Oleksij Rempel
2020-03-18 12:03 ` [PATCH v1 3/6] ARM: dts: add Protonic WD2 board Oleksij Rempel
2020-03-18 12:03 ` [PATCH v1 4/6] ARM: dts: add Protonic VT7 board Oleksij Rempel
2020-03-18 12:03 ` Oleksij Rempel [this message]
2020-03-18 12:03 ` [PATCH v1 6/6] m arch/arm/boot/dts/imx6q-prti6q.dts Oleksij Rempel
2020-03-18 12:27 ` Oleksij Rempel
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200318120354.4989-5-o.rempel@pengutronix.de \
--to=o.rempel@pengutronix.de \
--cc=david@protonic.nl \
--cc=devicetree@vger.kernel.org \
--cc=festevam@gmail.com \
--cc=kernel@pengutronix.de \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-imx@nxp.com \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=s.hauer@pengutronix.de \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).