[RESEND PATCH v3 0/3] Add Reset and Wakeup support for CCS811

[RESEND PATCH v3 0/3] Add Reset and Wakeup support for CCS811

[mani]

From: Manivannan Sadhasivam <mani@kernel.org>

Hello,

This patchset adds external reset and wakeup support for CCS811 VOC
gas sensor. The nRESET and nWAKE pins available on the device are
utilised to provide these functionalities.

The patchset has been validated using CCS811 connected to STM32MP1 based
board over I2C.

While at it, the devicetree yaml binding and OF match table for this sensor
are also added.

Thanks,
Mani

Changes in v3:

* Added ccs811_set_wake(false) to all error paths before calling it actually
* Added Andy's reviewed-by tag
* Added comment for reset procedure and dropped error print for gpio request

Changes in v2:

* Fixed DT binding schema and switched to dual license (GPL/BSD)
* Returned actual error code from devm_gpiod_get_optional()
* Dropped of.h include and of_match_ptr()

Manivannan Sadhasivam (3):
  dt-bindings: iio: chemical: Add binding for CCS811 VOC sensor
  iio: chemical: Add support for external Reset and Wakeup in CCS811
  iio: chemical: Add OF match table for CCS811 VOC sensor

 .../bindings/iio/chemical/ams,ccs811.yaml     |  51 ++++++++
 drivers/iio/chemical/ccs811.c                 | 112 ++++++++++++++++--
 2 files changed, 152 insertions(+), 11 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/iio/chemical/ams,ccs811.yaml

-- 
2.17.1

[RESEND PATCH v3 1/3] dt-bindings: iio: chemical: Add binding for CCS811 VOC sensor

[mani]

From: Manivannan Sadhasivam <mani@kernel.org>

This commit adds devicetree binding for AMS CCS811 VOC sensor.

Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
---
 .../bindings/iio/chemical/ams,ccs811.yaml     | 51 +++++++++++++++++++
 1 file changed, 51 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/iio/chemical/ams,ccs811.yaml

diff --git a/Documentation/devicetree/bindings/iio/chemical/ams,ccs811.yaml b/Documentation/devicetree/bindings/iio/chemical/ams,ccs811.yaml
new file mode 100644
index 000000000000..5cb068666a3e
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/chemical/ams,ccs811.yaml
@@ -0,0 +1,51 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/chemical/ams,ccs811.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: AMS CCS811 VOC Sensor
+
+maintainers:
+  - Narcisa Vasile <narcisaanamaria12@gmail.com>
+
+description: |
+  Ultra-Low Power Digital Gas Sensor for Monitoring Indoor Air Quality.
+
+properties:
+  compatible:
+    enum:
+      - ams,ccs811
+  reg:
+    maxItems: 1
+
+  reset-gpios:
+    description: GPIO connected to the nRESET line. This is an active low
+                 input to CCS811.
+    maxItems: 1
+
+  wakeup-gpios:
+    description: GPIO connected to the nWAKE line. This is an active low
+                 input to CCS811.
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      voc@5b {
+        compatible = "ams,ccs811";
+        reg = <0x5b>;
+        reset-gpios = <&gpioa 11 GPIO_ACTIVE_LOW>;
+        wakeup-gpios = <&gpioa 12 GPIO_ACTIVE_LOW>;
+      };
+    };
+
+...
-- 
2.17.1

[RESEND PATCH v3 2/3] iio: chemical: Add support for external Reset and Wakeup in CCS811

[mani]

From: Manivannan Sadhasivam <mani@kernel.org>

CCS811 VOC sensor exposes nRESET and nWAKE pins which can be connected
to GPIO pins of the host controller. These pins can be used to externally
release the device from reset and also to wake it up before any I2C
transaction. The initial driver support assumed that the nRESET pin is not
connected and the nWAKE pin is tied to ground.

This commit improves it by adding support for controlling those two pins
externally using a host controller. For the case of reset, if the hardware
reset is not available, the mechanism to do software reset is also added.

As a side effect of doing this, the IIO device allocation needs to be
slightly moved to top of probe to make use of priv data early.

Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
---
 drivers/iio/chemical/ccs811.c | 105 ++++++++++++++++++++++++++++++----
 1 file changed, 94 insertions(+), 11 deletions(-)

diff --git a/drivers/iio/chemical/ccs811.c b/drivers/iio/chemical/ccs811.c
index 2ebdfc35bcda..1500e4b0dfbd 100644
--- a/drivers/iio/chemical/ccs811.c
+++ b/drivers/iio/chemical/ccs811.c
@@ -16,6 +16,7 @@
  */
 
 #include <linux/delay.h>
+#include <linux/gpio/consumer.h>
 #include <linux/i2c.h>
 #include <linux/iio/iio.h>
 #include <linux/iio/buffer.h>
@@ -36,6 +37,7 @@
 #define CCS811_ERR		0xE0
 /* Used to transition from boot to application mode */
 #define CCS811_APP_START	0xF4
+#define CCS811_SW_RESET		0xFF
 
 /* Status register flags */
 #define CCS811_STATUS_ERROR		BIT(0)
@@ -74,6 +76,7 @@ struct ccs811_data {
 	struct mutex lock; /* Protect readings */
 	struct ccs811_reading buffer;
 	struct iio_trigger *drdy_trig;
+	struct gpio_desc *wakeup_gpio;
 	bool drdy_trig_on;
 };
 
@@ -166,10 +169,25 @@ static int ccs811_setup(struct i2c_client *client)
 					 CCS811_MODE_IAQ_1SEC);
 }
 
+static void ccs811_set_wakeup(struct ccs811_data *data, bool enable)
+{
+	if (!data->wakeup_gpio)
+		return;
+
+	gpiod_set_value(data->wakeup_gpio, enable);
+
+	if (enable)
+		usleep_range(50, 60);
+	else
+		usleep_range(20, 30);
+}
+
 static int ccs811_get_measurement(struct ccs811_data *data)
 {
 	int ret, tries = 11;
 
+	ccs811_set_wakeup(data, true);
+
 	/* Maximum waiting time: 1s, as measurements are made every second */
 	while (tries-- > 0) {
 		ret = i2c_smbus_read_byte_data(data->client, CCS811_STATUS);
@@ -183,9 +201,12 @@ static int ccs811_get_measurement(struct ccs811_data *data)
 	if (!(ret & CCS811_STATUS_DATA_READY))
 		return -EIO;
 
-	return i2c_smbus_read_i2c_block_data(data->client,
+	ret = i2c_smbus_read_i2c_block_data(data->client,
 					    CCS811_ALG_RESULT_DATA, 8,
 					    (char *)&data->buffer);
+	ccs811_set_wakeup(data, false);
+
+	return ret;
 }
 
 static int ccs811_read_raw(struct iio_dev *indio_dev,
@@ -336,6 +357,45 @@ static irqreturn_t ccs811_data_rdy_trigger_poll(int irq, void *private)
 	return IRQ_HANDLED;
 }
 
+static int ccs811_reset(struct i2c_client *client)
+{
+	struct gpio_desc *reset_gpio;
+	int ret;
+
+	reset_gpio = devm_gpiod_get_optional(&client->dev, "reset",
+					     GPIOD_OUT_LOW);
+	if (IS_ERR(reset_gpio))
+		return PTR_ERR(reset_gpio);
+
+	/* Try to reset using nRESET pin if available else do SW reset */
+	if (reset_gpio) {
+		gpiod_set_value(reset_gpio, 1);
+		usleep_range(20, 30);
+		gpiod_set_value(reset_gpio, 0);
+	} else {
+		/*
+		 * As per the datasheet, this sequence of values needs to be
+		 * written to the SW_RESET register for triggering the soft
+		 * reset in the device and placing it in boot mode.
+		 */
+		static const u8 reset_seq[] = {
+			0x11, 0xE5, 0x72, 0x8A,
+		};
+
+		ret = i2c_smbus_write_i2c_block_data(client, CCS811_SW_RESET,
+					     sizeof(reset_seq), reset_seq);
+		if (ret < 0) {
+			dev_err(&client->dev, "Failed to reset sensor\n");
+			return ret;
+		}
+	}
+
+	/* tSTART delay required after reset */
+	usleep_range(1000, 2000);
+
+	return 0;
+}
+
 static int ccs811_probe(struct i2c_client *client,
 			const struct i2c_device_id *id)
 {
@@ -348,36 +408,59 @@ static int ccs811_probe(struct i2c_client *client,
 				     | I2C_FUNC_SMBUS_READ_I2C_BLOCK))
 		return -EOPNOTSUPP;
 
+	indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	data = iio_priv(indio_dev);
+	i2c_set_clientdata(client, indio_dev);
+	data->client = client;
+
+	data->wakeup_gpio = devm_gpiod_get_optional(&client->dev, "wakeup",
+						    GPIOD_OUT_HIGH);
+	if (IS_ERR(data->wakeup_gpio))
+		return PTR_ERR(data->wakeup_gpio);
+
+	ccs811_set_wakeup(data, true);
+
+	ret = ccs811_reset(client);
+	if (ret) {
+		ccs811_set_wakeup(data, false);
+		return ret;
+	}
+
 	/* Check hardware id (should be 0x81 for this family of devices) */
 	ret = i2c_smbus_read_byte_data(client, CCS811_HW_ID);
-	if (ret < 0)
+	if (ret < 0) {
+		ccs811_set_wakeup(data, false);
 		return ret;
+	}
 
 	if (ret != CCS811_HW_ID_VALUE) {
 		dev_err(&client->dev, "hardware id doesn't match CCS81x\n");
+		ccs811_set_wakeup(data, false);
 		return -ENODEV;
 	}
 
 	ret = i2c_smbus_read_byte_data(client, CCS811_HW_VERSION);
-	if (ret < 0)
+	if (ret < 0) {
+		ccs811_set_wakeup(data, false);
 		return ret;
+	}
 
 	if ((ret & CCS811_HW_VERSION_MASK) != CCS811_HW_VERSION_VALUE) {
 		dev_err(&client->dev, "no CCS811 sensor\n");
+		ccs811_set_wakeup(data, false);
 		return -ENODEV;
 	}
 
-	indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
-	if (!indio_dev)
-		return -ENOMEM;
-
 	ret = ccs811_setup(client);
-	if (ret < 0)
+	if (ret < 0) {
+		ccs811_set_wakeup(data, false);
 		return ret;
+	}
 
-	data = iio_priv(indio_dev);
-	i2c_set_clientdata(client, indio_dev);
-	data->client = client;
+	ccs811_set_wakeup(data, false);
 
 	mutex_init(&data->lock);
 
-- 
2.17.1

[RESEND PATCH v3 3/3] iio: chemical: Add OF match table for CCS811 VOC sensor

[mani]

From: Manivannan Sadhasivam <mani@kernel.org>

Add devicetree OF match table support for CCS811 VOC sensor.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
---
 drivers/iio/chemical/ccs811.c | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/drivers/iio/chemical/ccs811.c b/drivers/iio/chemical/ccs811.c
index 1500e4b0dfbd..3ecd633f9ed3 100644
--- a/drivers/iio/chemical/ccs811.c
+++ b/drivers/iio/chemical/ccs811.c
@@ -549,9 +549,16 @@ static const struct i2c_device_id ccs811_id[] = {
 };
 MODULE_DEVICE_TABLE(i2c, ccs811_id);
 
+static const struct of_device_id ccs811_dt_ids[] = {
+	{ .compatible = "ams,ccs811" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, ccs811_dt_ids);
+
 static struct i2c_driver ccs811_driver = {
 	.driver = {
 		.name = "ccs811",
+		.of_match_table = ccs811_dt_ids,
 	},
 	.probe = ccs811_probe,
 	.remove = ccs811_remove,
-- 
2.17.1

Re: [RESEND PATCH v3 2/3] iio: chemical: Add support for external Reset and Wakeup in CCS811

[Andy Shevchenko]

On Tue, Apr 14, 2020 at 9:49 PM <mani@kernel.org> wrote:
>
> From: Manivannan Sadhasivam <mani@kernel.org>
>
> CCS811 VOC sensor exposes nRESET and nWAKE pins which can be connected
> to GPIO pins of the host controller. These pins can be used to externally
> release the device from reset and also to wake it up before any I2C
> transaction. The initial driver support assumed that the nRESET pin is not
> connected and the nWAKE pin is tied to ground.
>
> This commit improves it by adding support for controlling those two pins
> externally using a host controller. For the case of reset, if the hardware
> reset is not available, the mechanism to do software reset is also added.
>
> As a side effect of doing this, the IIO device allocation needs to be
> slightly moved to top of probe to make use of priv data early.
>

LGTM,
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>

> Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
> ---
>  drivers/iio/chemical/ccs811.c | 105 ++++++++++++++++++++++++++++++----
>  1 file changed, 94 insertions(+), 11 deletions(-)
>
> diff --git a/drivers/iio/chemical/ccs811.c b/drivers/iio/chemical/ccs811.c
> index 2ebdfc35bcda..1500e4b0dfbd 100644
> --- a/drivers/iio/chemical/ccs811.c
> +++ b/drivers/iio/chemical/ccs811.c
> @@ -16,6 +16,7 @@
>   */
>
>  #include <linux/delay.h>
> +#include <linux/gpio/consumer.h>
>  #include <linux/i2c.h>
>  #include <linux/iio/iio.h>
>  #include <linux/iio/buffer.h>
> @@ -36,6 +37,7 @@
>  #define CCS811_ERR             0xE0
>  /* Used to transition from boot to application mode */
>  #define CCS811_APP_START       0xF4
> +#define CCS811_SW_RESET                0xFF
>
>  /* Status register flags */
>  #define CCS811_STATUS_ERROR            BIT(0)
> @@ -74,6 +76,7 @@ struct ccs811_data {
>         struct mutex lock; /* Protect readings */
>         struct ccs811_reading buffer;
>         struct iio_trigger *drdy_trig;
> +       struct gpio_desc *wakeup_gpio;
>         bool drdy_trig_on;
>  };
>
> @@ -166,10 +169,25 @@ static int ccs811_setup(struct i2c_client *client)
>                                          CCS811_MODE_IAQ_1SEC);
>  }
>
> +static void ccs811_set_wakeup(struct ccs811_data *data, bool enable)
> +{
> +       if (!data->wakeup_gpio)
> +               return;
> +
> +       gpiod_set_value(data->wakeup_gpio, enable);
> +
> +       if (enable)
> +               usleep_range(50, 60);
> +       else
> +               usleep_range(20, 30);
> +}
> +
>  static int ccs811_get_measurement(struct ccs811_data *data)
>  {
>         int ret, tries = 11;
>
> +       ccs811_set_wakeup(data, true);
> +
>         /* Maximum waiting time: 1s, as measurements are made every second */
>         while (tries-- > 0) {
>                 ret = i2c_smbus_read_byte_data(data->client, CCS811_STATUS);
> @@ -183,9 +201,12 @@ static int ccs811_get_measurement(struct ccs811_data *data)
>         if (!(ret & CCS811_STATUS_DATA_READY))
>                 return -EIO;
>
> -       return i2c_smbus_read_i2c_block_data(data->client,
> +       ret = i2c_smbus_read_i2c_block_data(data->client,
>                                             CCS811_ALG_RESULT_DATA, 8,
>                                             (char *)&data->buffer);
> +       ccs811_set_wakeup(data, false);
> +
> +       return ret;
>  }
>
>  static int ccs811_read_raw(struct iio_dev *indio_dev,
> @@ -336,6 +357,45 @@ static irqreturn_t ccs811_data_rdy_trigger_poll(int irq, void *private)
>         return IRQ_HANDLED;
>  }
>
> +static int ccs811_reset(struct i2c_client *client)
> +{
> +       struct gpio_desc *reset_gpio;
> +       int ret;
> +
> +       reset_gpio = devm_gpiod_get_optional(&client->dev, "reset",
> +                                            GPIOD_OUT_LOW);
> +       if (IS_ERR(reset_gpio))
> +               return PTR_ERR(reset_gpio);
> +
> +       /* Try to reset using nRESET pin if available else do SW reset */
> +       if (reset_gpio) {
> +               gpiod_set_value(reset_gpio, 1);
> +               usleep_range(20, 30);
> +               gpiod_set_value(reset_gpio, 0);
> +       } else {
> +               /*
> +                * As per the datasheet, this sequence of values needs to be
> +                * written to the SW_RESET register for triggering the soft
> +                * reset in the device and placing it in boot mode.
> +                */
> +               static const u8 reset_seq[] = {
> +                       0x11, 0xE5, 0x72, 0x8A,
> +               };
> +
> +               ret = i2c_smbus_write_i2c_block_data(client, CCS811_SW_RESET,
> +                                            sizeof(reset_seq), reset_seq);
> +               if (ret < 0) {
> +                       dev_err(&client->dev, "Failed to reset sensor\n");
> +                       return ret;
> +               }
> +       }
> +
> +       /* tSTART delay required after reset */
> +       usleep_range(1000, 2000);
> +
> +       return 0;
> +}
> +
>  static int ccs811_probe(struct i2c_client *client,
>                         const struct i2c_device_id *id)
>  {
> @@ -348,36 +408,59 @@ static int ccs811_probe(struct i2c_client *client,
>                                      | I2C_FUNC_SMBUS_READ_I2C_BLOCK))
>                 return -EOPNOTSUPP;
>
> +       indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
> +       if (!indio_dev)
> +               return -ENOMEM;
> +
> +       data = iio_priv(indio_dev);
> +       i2c_set_clientdata(client, indio_dev);
> +       data->client = client;
> +
> +       data->wakeup_gpio = devm_gpiod_get_optional(&client->dev, "wakeup",
> +                                                   GPIOD_OUT_HIGH);
> +       if (IS_ERR(data->wakeup_gpio))
> +               return PTR_ERR(data->wakeup_gpio);
> +
> +       ccs811_set_wakeup(data, true);
> +
> +       ret = ccs811_reset(client);
> +       if (ret) {
> +               ccs811_set_wakeup(data, false);
> +               return ret;
> +       }
> +
>         /* Check hardware id (should be 0x81 for this family of devices) */
>         ret = i2c_smbus_read_byte_data(client, CCS811_HW_ID);
> -       if (ret < 0)
> +       if (ret < 0) {
> +               ccs811_set_wakeup(data, false);
>                 return ret;
> +       }
>
>         if (ret != CCS811_HW_ID_VALUE) {
>                 dev_err(&client->dev, "hardware id doesn't match CCS81x\n");
> +               ccs811_set_wakeup(data, false);
>                 return -ENODEV;
>         }
>
>         ret = i2c_smbus_read_byte_data(client, CCS811_HW_VERSION);
> -       if (ret < 0)
> +       if (ret < 0) {
> +               ccs811_set_wakeup(data, false);
>                 return ret;
> +       }
>
>         if ((ret & CCS811_HW_VERSION_MASK) != CCS811_HW_VERSION_VALUE) {
>                 dev_err(&client->dev, "no CCS811 sensor\n");
> +               ccs811_set_wakeup(data, false);
>                 return -ENODEV;
>         }
>
> -       indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
> -       if (!indio_dev)
> -               return -ENOMEM;
> -
>         ret = ccs811_setup(client);
> -       if (ret < 0)
> +       if (ret < 0) {
> +               ccs811_set_wakeup(data, false);
>                 return ret;
> +       }
>
> -       data = iio_priv(indio_dev);
> -       i2c_set_clientdata(client, indio_dev);
> -       data->client = client;
> +       ccs811_set_wakeup(data, false);
>
>         mutex_init(&data->lock);
>
> --
> 2.17.1
>


-- 
With Best Regards,
Andy Shevchenko

Re: [RESEND PATCH v3 0/3] Add Reset and Wakeup support for CCS811

[Jonathan Cameron]

On Wed, 15 Apr 2020 00:19:27 +0530
mani@kernel.org wrote:

> From: Manivannan Sadhasivam <mani@kernel.org>
> 
> Hello,
> 
> This patchset adds external reset and wakeup support for CCS811 VOC
> gas sensor. The nRESET and nWAKE pins available on the device are
> utilised to provide these functionalities.
> 
> The patchset has been validated using CCS811 connected to STM32MP1 based
> board over I2C.
> 
> While at it, the devicetree yaml binding and OF match table for this sensor
> are also added.
> 
Looks good to me. I'd just like to give it a bit longer to allow dt
maintainers to take a look if they wish.

Thanks,

Jonathan

> Thanks,
> Mani
> 
> Changes in v3:
> 
> * Added ccs811_set_wake(false) to all error paths before calling it actually
> * Added Andy's reviewed-by tag
> * Added comment for reset procedure and dropped error print for gpio request
> 
> Changes in v2:
> 
> * Fixed DT binding schema and switched to dual license (GPL/BSD)
> * Returned actual error code from devm_gpiod_get_optional()
> * Dropped of.h include and of_match_ptr()
> 
> Manivannan Sadhasivam (3):
>   dt-bindings: iio: chemical: Add binding for CCS811 VOC sensor
>   iio: chemical: Add support for external Reset and Wakeup in CCS811
>   iio: chemical: Add OF match table for CCS811 VOC sensor
> 
>  .../bindings/iio/chemical/ams,ccs811.yaml     |  51 ++++++++
>  drivers/iio/chemical/ccs811.c                 | 112 ++++++++++++++++--
>  2 files changed, 152 insertions(+), 11 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/iio/chemical/ams,ccs811.yaml
> 

Re: [RESEND PATCH v3 1/3] dt-bindings: iio: chemical: Add binding for CCS811 VOC sensor

[Rob Herring]

On Wed, Apr 15, 2020 at 12:19:28AM +0530, mani@kernel.org wrote:
> From: Manivannan Sadhasivam <mani@kernel.org>
> 
> This commit adds devicetree binding for AMS CCS811 VOC sensor.
> 
> Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
> ---
>  .../bindings/iio/chemical/ams,ccs811.yaml     | 51 +++++++++++++++++++
>  1 file changed, 51 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/iio/chemical/ams,ccs811.yaml
> 
> diff --git a/Documentation/devicetree/bindings/iio/chemical/ams,ccs811.yaml b/Documentation/devicetree/bindings/iio/chemical/ams,ccs811.yaml
> new file mode 100644
> index 000000000000..5cb068666a3e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/chemical/ams,ccs811.yaml
> @@ -0,0 +1,51 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/iio/chemical/ams,ccs811.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: AMS CCS811 VOC Sensor
> +
> +maintainers:
> +  - Narcisa Vasile <narcisaanamaria12@gmail.com>
> +
> +description: |
> +  Ultra-Low Power Digital Gas Sensor for Monitoring Indoor Air Quality.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - ams,ccs811
> +  reg:
> +    maxItems: 1
> +
> +  reset-gpios:
> +    description: GPIO connected to the nRESET line. This is an active low
> +                 input to CCS811.
> +    maxItems: 1
> +
> +  wakeup-gpios:
> +    description: GPIO connected to the nWAKE line. This is an active low
> +                 input to CCS811.
> +    maxItems: 1
> +
> +required:
> +  - compatible
> +  - reg

Add:

additionalProperties: false

With that,

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [RESEND PATCH v3 1/3] dt-bindings: iio: chemical: Add binding for CCS811 VOC sensor

[Manivannan Sadhasivam]

On Mon, Apr 20, 2020 at 04:11:11PM -0500, Rob Herring wrote:
> On Wed, Apr 15, 2020 at 12:19:28AM +0530, mani@kernel.org wrote:
> > From: Manivannan Sadhasivam <mani@kernel.org>
> > 
> > This commit adds devicetree binding for AMS CCS811 VOC sensor.
> > 
> > Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
> > ---
> >  .../bindings/iio/chemical/ams,ccs811.yaml     | 51 +++++++++++++++++++
> >  1 file changed, 51 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/iio/chemical/ams,ccs811.yaml
> > 
> > diff --git a/Documentation/devicetree/bindings/iio/chemical/ams,ccs811.yaml b/Documentation/devicetree/bindings/iio/chemical/ams,ccs811.yaml
> > new file mode 100644
> > index 000000000000..5cb068666a3e
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/iio/chemical/ams,ccs811.yaml
> > @@ -0,0 +1,51 @@
> > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/iio/chemical/ams,ccs811.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: AMS CCS811 VOC Sensor
> > +
> > +maintainers:
> > +  - Narcisa Vasile <narcisaanamaria12@gmail.com>
> > +
> > +description: |
> > +  Ultra-Low Power Digital Gas Sensor for Monitoring Indoor Air Quality.
> > +
> > +properties:
> > +  compatible:
> > +    enum:
> > +      - ams,ccs811
> > +  reg:
> > +    maxItems: 1
> > +
> > +  reset-gpios:
> > +    description: GPIO connected to the nRESET line. This is an active low
> > +                 input to CCS811.
> > +    maxItems: 1
> > +
> > +  wakeup-gpios:
> > +    description: GPIO connected to the nWAKE line. This is an active low
> > +                 input to CCS811.
> > +    maxItems: 1
> > +
> > +required:
> > +  - compatible
> > +  - reg
> 
> Add:
> 
> additionalProperties: false
> 

Hi Jonathan,

Do you want me to spin another series or you can add it while applying?

Thanks,
Mani

> With that,
> 
> Reviewed-by: Rob Herring <robh@kernel.org>

Re: [RESEND PATCH v3 1/3] dt-bindings: iio: chemical: Add binding for CCS811 VOC sensor

[Jonathan Cameron]

On Wed, 22 Apr 2020 23:57:15 +0530
Manivannan Sadhasivam <mani@kernel.org> wrote:

> On Mon, Apr 20, 2020 at 04:11:11PM -0500, Rob Herring wrote:
> > On Wed, Apr 15, 2020 at 12:19:28AM +0530, mani@kernel.org wrote:  
> > > From: Manivannan Sadhasivam <mani@kernel.org>
> > > 
> > > This commit adds devicetree binding for AMS CCS811 VOC sensor.
> > > 
> > > Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
> > > ---
> > >  .../bindings/iio/chemical/ams,ccs811.yaml     | 51 +++++++++++++++++++
> > >  1 file changed, 51 insertions(+)
> > >  create mode 100644 Documentation/devicetree/bindings/iio/chemical/ams,ccs811.yaml
> > > 
> > > diff --git a/Documentation/devicetree/bindings/iio/chemical/ams,ccs811.yaml b/Documentation/devicetree/bindings/iio/chemical/ams,ccs811.yaml
> > > new file mode 100644
> > > index 000000000000..5cb068666a3e
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/iio/chemical/ams,ccs811.yaml
> > > @@ -0,0 +1,51 @@
> > > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> > > +%YAML 1.2
> > > +---
> > > +$id: http://devicetree.org/schemas/iio/chemical/ams,ccs811.yaml#
> > > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > > +
> > > +title: AMS CCS811 VOC Sensor
> > > +
> > > +maintainers:
> > > +  - Narcisa Vasile <narcisaanamaria12@gmail.com>
> > > +
> > > +description: |
> > > +  Ultra-Low Power Digital Gas Sensor for Monitoring Indoor Air Quality.
> > > +
> > > +properties:
> > > +  compatible:
> > > +    enum:
> > > +      - ams,ccs811
> > > +  reg:
> > > +    maxItems: 1
> > > +
> > > +  reset-gpios:
> > > +    description: GPIO connected to the nRESET line. This is an active low
> > > +                 input to CCS811.
> > > +    maxItems: 1
> > > +
> > > +  wakeup-gpios:
> > > +    description: GPIO connected to the nWAKE line. This is an active low
> > > +                 input to CCS811.
> > > +    maxItems: 1
> > > +
> > > +required:
> > > +  - compatible
> > > +  - reg  
> > 
> > Add:
> > 
> > additionalProperties: false
> >   
> 
> Hi Jonathan,
> 
> Do you want me to spin another series or you can add it while applying?
Added whilst applying.

Applied to the togreg branch of iio.git and pushed out as testing for
the autobuilders to poke at it.

Thanks,

Jonathan

> 
> Thanks,
> Mani
> 
> > With that,
> > 
> > Reviewed-by: Rob Herring <robh@kernel.org>  

Re: [RESEND PATCH v3 0/3] Add Reset and Wakeup support for CCS811

[Jonathan Cameron]

On Wed, 15 Apr 2020 00:19:27 +0530
mani@kernel.org wrote:

> From: Manivannan Sadhasivam <mani@kernel.org>
> 
> Hello,
> 
> This patchset adds external reset and wakeup support for CCS811 VOC
> gas sensor. The nRESET and nWAKE pins available on the device are
> utilised to provide these functionalities.
> 
> The patchset has been validated using CCS811 connected to STM32MP1 based
> board over I2C.
> 
> While at it, the devicetree yaml binding and OF match table for this sensor
> are also added.
> 
> Thanks,
> Mani

All applied to the togreg branch of iio.git and pushed out as testing for
the autobuilders to play with it.

Thanks,

Jonathan

> 
> Changes in v3:
> 
> * Added ccs811_set_wake(false) to all error paths before calling it actually
> * Added Andy's reviewed-by tag
> * Added comment for reset procedure and dropped error print for gpio request
> 
> Changes in v2:
> 
> * Fixed DT binding schema and switched to dual license (GPL/BSD)
> * Returned actual error code from devm_gpiod_get_optional()
> * Dropped of.h include and of_match_ptr()
> 
> Manivannan Sadhasivam (3):
>   dt-bindings: iio: chemical: Add binding for CCS811 VOC sensor
>   iio: chemical: Add support for external Reset and Wakeup in CCS811
>   iio: chemical: Add OF match table for CCS811 VOC sensor
> 
>  .../bindings/iio/chemical/ams,ccs811.yaml     |  51 ++++++++
>  drivers/iio/chemical/ccs811.c                 | 112 ++++++++++++++++--
>  2 files changed, 152 insertions(+), 11 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/iio/chemical/ams,ccs811.yaml
>