* [PATCH] dt-bindings: Remove more cases of 'allOf' containing a '$ref'
@ 2020-06-11 15:20 Rob Herring
0 siblings, 0 replies; 2+ messages in thread
From: Rob Herring @ 2020-06-11 15:20 UTC (permalink / raw)
To: devicetree; +Cc: linux-kernel
Another round of 'allOf' removals that came in this cycle.
json-schema versions draft7 and earlier have a weird behavior in that
any keywords combined with a '$ref' are ignored (silently). The correct
form was to put a '$ref' under an 'allOf'. This behavior is now changed
in the 2019-09 json-schema spec and '$ref' can be mixed with other
keywords. The json-schema library doesn't yet support this, but the
tooling now does a fixup for this and either way works.
This has been a constant source of review comments, so let's change this
treewide so everyone copies the simpler syntax.
Signed-off-by: Rob Herring <robh@kernel.org>
---
.../arm/tegra/nvidia,tegra20-pmc.yaml | 5 +-
.../bindings/ata/sata_highbank.yaml | 21 +-
.../bindings/gpio/snps,dw-apb-gpio.yaml | 7 +-
.../bindings/iio/imu/adi,adis16475.yaml | 3 +-
.../bindings/iio/light/amstaos,tsl2563.yaml | 5 +-
.../devicetree/bindings/input/iqs269a.yaml | 222 ++++++++----------
.../loongson,pch-msi.yaml | 14 +-
.../loongson,pch-pic.yaml | 7 +-
.../devicetree/bindings/ipmi/ipmi-smic.yaml | 10 +-
.../bindings/leds/backlight/qcom-wled.yaml | 43 ++--
.../devicetree/bindings/leds/leds-aw2013.yaml | 3 +-
.../bindings/leds/leds-sgm3140.yaml | 3 +-
.../devicetree/bindings/media/i2c/ov8856.yaml | 3 +-
.../memory-controllers/ingenic,nemc.yaml | 5 +-
.../bindings/net/ti,k3-am654-cpsw-nuss.yaml | 3 +-
.../bindings/net/ti,k3-am654-cpts.yaml | 6 +-
.../devicetree/bindings/pci/cdns-pcie-ep.yaml | 3 +-
.../bindings/pci/cdns-pcie-host.yaml | 3 +-
.../bindings/phy/calxeda-combophy.yaml | 5 +-
.../bindings/phy/renesas,usb3-phy.yaml | 5 +-
.../bindings/power/supply/cw2015_battery.yaml | 15 +-
.../power/supply/sbs,sbs-battery.yaml | 6 +-
.../bindings/regulator/maxim,max77826.yaml | 9 +-
.../regulator/rohm,bd71847-regulator.yaml | 27 +--
.../devicetree/bindings/rng/arm-cctrng.yaml | 6 +-
.../bindings/serial/samsung_uart.yaml | 5 +-
.../bindings/soc/qcom/qcom,geni-se.yaml | 9 +-
.../devicetree/bindings/sound/fsl,easrc.yaml | 19 +-
.../bindings/sound/simple-card.yaml | 10 +-
.../bindings/sound/tlv320adcx140.yaml | 26 +-
.../thermal/socionext,uniphier-thermal.yaml | 5 +-
.../bindings/usb/aspeed,usb-vhub.yaml | 24 +-
.../bindings/watchdog/arm-smc-wdt.yaml | 3 +-
33 files changed, 224 insertions(+), 316 deletions(-)
diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.yaml b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.yaml
index 81534d04094b..b71a20af5f70 100644
--- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.yaml
+++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.yaml
@@ -85,9 +85,8 @@ properties:
CPU power good signal from external PMIC to PMC is enabled.
nvidia,suspend-mode:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [0, 1, 2]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2]
description:
The suspend mode that the platform should use.
Mode 0 is for LP0, CPU + Core voltage off and DRAM in self-refresh
diff --git a/Documentation/devicetree/bindings/ata/sata_highbank.yaml b/Documentation/devicetree/bindings/ata/sata_highbank.yaml
index b195457006cc..5e2a2394e600 100644
--- a/Documentation/devicetree/bindings/ata/sata_highbank.yaml
+++ b/Documentation/devicetree/bindings/ata/sata_highbank.yaml
@@ -40,28 +40,25 @@ properties:
calxeda,led-order:
description: Maps port numbers to offsets within the SGPIO bitstream.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - minItems: 1
- maxItems: 8
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 1
+ maxItems: 8
calxeda,port-phys:
description: |
phandle-combophy and lane assignment, which maps each SATA port to a
combophy and a lane within that combophy
- allOf:
- - $ref: /schemas/types.yaml#/definitions/phandle-array
- - minItems: 1
- maxItems: 8
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ minItems: 1
+ maxItems: 8
calxeda,tx-atten:
description: |
Contains TX attenuation override codes, one per port.
The upper 24 bits of each entry are always 0 and thus ignored.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - minItems: 1
- maxItems: 8
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 1
+ maxItems: 8
calxeda,sgpio-gpio:
description: |
diff --git a/Documentation/devicetree/bindings/gpio/snps,dw-apb-gpio.yaml b/Documentation/devicetree/bindings/gpio/snps,dw-apb-gpio.yaml
index 04a3c51e1dc1..1240f6289249 100644
--- a/Documentation/devicetree/bindings/gpio/snps,dw-apb-gpio.yaml
+++ b/Documentation/devicetree/bindings/gpio/snps,dw-apb-gpio.yaml
@@ -63,11 +63,10 @@ patternProperties:
snps,nr-gpios:
description: The number of GPIO pins exported by the port.
+ $ref: /schemas/types.yaml#/definitions/uint32
default: 32
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 1
- maximum: 32
+ minimum: 1
+ maximum: 32
interrupts:
description: |
diff --git a/Documentation/devicetree/bindings/iio/imu/adi,adis16475.yaml b/Documentation/devicetree/bindings/iio/imu/adi,adis16475.yaml
index 98baecb4b98a..208faaffa58d 100644
--- a/Documentation/devicetree/bindings/iio/imu/adi,adis16475.yaml
+++ b/Documentation/devicetree/bindings/iio/imu/adi,adis16475.yaml
@@ -67,8 +67,7 @@ properties:
1 - direct_sync
2 - scaled_sync
3 - pulse_sync
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
minimum: 0
maximum: 3
diff --git a/Documentation/devicetree/bindings/iio/light/amstaos,tsl2563.yaml b/Documentation/devicetree/bindings/iio/light/amstaos,tsl2563.yaml
index efd2eba5f23c..e201a06d8fdc 100644
--- a/Documentation/devicetree/bindings/iio/light/amstaos,tsl2563.yaml
+++ b/Documentation/devicetree/bindings/iio/light/amstaos,tsl2563.yaml
@@ -25,9 +25,8 @@ properties:
amstaos,cover-comp-gain:
description: Multiplier for gain compensation
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [1, 16]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [1, 16]
required:
- compatible
diff --git a/Documentation/devicetree/bindings/input/iqs269a.yaml b/Documentation/devicetree/bindings/input/iqs269a.yaml
index f0242bb4be81..9c154e5e1a91 100644
--- a/Documentation/devicetree/bindings/input/iqs269a.yaml
+++ b/Documentation/devicetree/bindings/input/iqs269a.yaml
@@ -40,10 +40,9 @@ properties:
posed on channels 6 and 7 by Hall-effect sensing.
azoteq,suspend-mode:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [0, 1, 2, 3]
- default: 0
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+ default: 0
description: |
Specifies the power mode during suspend as follows:
0: Automatic (same as normal runtime, i.e. suspend/resume disabled)
@@ -56,11 +55,10 @@ properties:
description: Divides the device's core clock by a factor of 4.
azoteq,ulp-update:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 0
- maximum: 7
- default: 3
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 7
+ default: 3
description: Specifies the ultra-low-power mode update rate.
azoteq,reseed-offset:
@@ -70,34 +68,30 @@ properties:
reseed events.
azoteq,filt-str-lp-lta:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [0, 1, 2, 3]
- default: 0
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+ default: 0
description:
Specifies the long-term average filter strength during low-power mode.
azoteq,filt-str-lp-cnt:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [0, 1, 2, 3]
- default: 0
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+ default: 0
description:
Specifies the raw count filter strength during low-power mode.
azoteq,filt-str-np-lta:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [0, 1, 2, 3]
- default: 0
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+ default: 0
description:
Specifies the long-term average filter strength during normal-power mode.
azoteq,filt-str-np-cnt:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [0, 1, 2, 3]
- default: 0
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+ default: 0
description:
Specifies the raw count filter strength during normal-power mode.
@@ -156,11 +150,10 @@ properties:
description: Disables all raw count filtering.
azoteq,gpio3-select:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 0
- maximum: 7
- default: 0
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 7
+ default: 0
description:
Selects the channel for which the GPIO3 pin represents touch state.
@@ -172,10 +165,9 @@ properties:
in either direction.
azoteq,tx-freq:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [0, 1, 2, 3]
- default: 0
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+ default: 0
description: |
Specifies the inductive sensing excitation frequency as follows (paren-
thesized numbers represent the frequency if 'azoteq,clk-div' is present):
@@ -189,10 +181,9 @@ properties:
description: Increases the global capacitance adder from 0.5 pF to 1.5 pF.
azoteq,reseed-select:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [0, 1, 2, 3]
- default: 0
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+ default: 0
description: |
Specifies the event(s) that prompt the device to reseed (i.e. reset the
long-term average) of an associated channel as follows:
@@ -208,10 +199,9 @@ properties:
channels.
azoteq,filt-str-slider:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [0, 1, 2, 3]
- default: 1
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+ default: 1
description: Specifies the slider coordinate filter strength.
patternProperties:
@@ -246,27 +236,25 @@ patternProperties:
description: Specifies that the channel participates in slider 1.
azoteq,rx-enable:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - minItems: 1
- maxItems: 8
- items:
- minimum: 0
- maximum: 7
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 1
+ maxItems: 8
+ items:
+ minimum: 0
+ maximum: 7
description:
Specifies the CRX pin(s) associated with the channel. By default, only
the CRX pin corresponding to the channel's index is enabled (e.g. CRX0
for channel 0).
azoteq,tx-enable:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - minItems: 1
- maxItems: 8
- items:
- minimum: 0
- maximum: 7
- default: [0, 1, 2, 3, 4, 5, 6, 7]
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 1
+ maxItems: 8
+ items:
+ minimum: 0
+ maximum: 7
+ default: [0, 1, 2, 3, 4, 5, 6, 7]
description: Specifies the TX pin(s) associated with the channel.
azoteq,meas-cap-decrease:
@@ -279,10 +267,9 @@ patternProperties:
description: Floats any inactive CRX pins instead of grounding them.
azoteq,local-cap-size:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [0, 1, 2]
- default: 0
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2]
+ default: 0
description: |
Specifies the capacitance to be added to the channel as follows:
0: None
@@ -296,10 +283,9 @@ patternProperties:
deep-touch events relative to their respective thresholds.
azoteq,proj-bias:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [0, 1, 2, 3]
- default: 2
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+ default: 2
description: |
Specifies the bias current applied during projected-capacitance
sensing as follows:
@@ -309,10 +295,9 @@ patternProperties:
3: 20 uA
azoteq,sense-mode:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [0, 1, 9, 14, 15]
- default: 0
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 9, 14, 15]
+ default: 0
description: |
Specifies the channel's sensing mode as follows:
0: Self capacitance
@@ -322,10 +307,9 @@ patternProperties:
15: Temperature
azoteq,sense-freq:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [0, 1, 2, 3]
- default: 1
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+ default: 1
description: |
Specifies the channel's sensing frequency as follows (parenthesized
numbers represent the frequency if 'azoteq,clk-div' is present):
@@ -339,10 +323,9 @@ patternProperties:
description: Enables the static front-end for the channel.
azoteq,ati-mode:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [0, 1, 2, 3]
- default: 3
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+ default: 3
description: |
Specifies the channel's ATI mode as follows:
0: Disabled
@@ -351,39 +334,35 @@ patternProperties:
3: Full
azoteq,ati-base:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [75, 100, 150, 200]
- default: 100
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [75, 100, 150, 200]
+ default: 100
description: Specifies the channel's ATI base.
azoteq,ati-target:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - multipleOf: 32
- minimum: 0
- maximum: 2016
- default: 512
+ $ref: /schemas/types.yaml#/definitions/uint32
+ multipleOf: 32
+ minimum: 0
+ maximum: 2016
+ default: 512
description: Specifies the channel's ATI target.
azoteq,assoc-select:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - minItems: 1
- maxItems: 8
- items:
- minimum: 0
- maximum: 7
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 1
+ maxItems: 8
+ items:
+ minimum: 0
+ maximum: 7
description:
Specifies the associated channels for which the channel serves as a
reference channel. By default, no channels are selected.
azoteq,assoc-weight:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 0
- maximum: 255
- default: 0
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 255
+ default: 0
description:
Specifies the channel's impact weight if it acts as an associated
channel (0 = 0% impact, 255 = 200% impact).
@@ -411,11 +390,10 @@ patternProperties:
properties:
azoteq,thresh:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 0
- maximum: 255
- default: 10
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 255
+ default: 10
description: Specifies the threshold for the event.
linux,code:
@@ -430,19 +408,17 @@ patternProperties:
properties:
azoteq,thresh:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 0
- maximum: 255
- default: 8
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 255
+ default: 8
description: Specifies the threshold for the event.
azoteq,hyst:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 0
- maximum: 15
- default: 4
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 15
+ default: 4
description: Specifies the hysteresis for the event.
linux,code:
@@ -457,19 +433,17 @@ patternProperties:
properties:
azoteq,thresh:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 0
- maximum: 255
- default: 26
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 255
+ default: 26
description: Specifies the threshold for the event.
azoteq,hyst:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 0
- maximum: 15
- default: 0
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 15
+ default: 0
description: Specifies the hysteresis for the event.
linux,code:
diff --git a/Documentation/devicetree/bindings/interrupt-controller/loongson,pch-msi.yaml b/Documentation/devicetree/bindings/interrupt-controller/loongson,pch-msi.yaml
index 1a5ebbdd219a..1b256d9dd92a 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/loongson,pch-msi.yaml
+++ b/Documentation/devicetree/bindings/interrupt-controller/loongson,pch-msi.yaml
@@ -25,19 +25,17 @@ properties:
description:
u32 value of the base of parent HyperTransport vector allocated
to PCH MSI.
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 0
- maximum: 255
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 255
loongson,msi-num-vecs:
description:
u32 value of the number of parent HyperTransport vectors allocated
to PCH MSI.
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 1
- maximum: 256
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 1
+ maximum: 256
msi-controller: true
diff --git a/Documentation/devicetree/bindings/interrupt-controller/loongson,pch-pic.yaml b/Documentation/devicetree/bindings/interrupt-controller/loongson,pch-pic.yaml
index 274adea13f33..a6dcbb2971a9 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/loongson,pch-pic.yaml
+++ b/Documentation/devicetree/bindings/interrupt-controller/loongson,pch-pic.yaml
@@ -25,10 +25,9 @@ properties:
description:
u32 value of the base of parent HyperTransport vector allocated
to PCH PIC.
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 0
- maximum: 192
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 192
interrupt-controller: true
diff --git a/Documentation/devicetree/bindings/ipmi/ipmi-smic.yaml b/Documentation/devicetree/bindings/ipmi/ipmi-smic.yaml
index f0bb157e9417..58fa76ee6176 100644
--- a/Documentation/devicetree/bindings/ipmi/ipmi-smic.yaml
+++ b/Documentation/devicetree/bindings/ipmi/ipmi-smic.yaml
@@ -31,9 +31,8 @@ properties:
reg-size:
description: The access width of the register in bytes. Defaults to 1.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [1, 2, 4, 8]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [1, 2, 4, 8]
reg-spacing:
$ref: /schemas/types.yaml#/definitions/uint32
@@ -43,9 +42,8 @@ properties:
description: |
The amount of bits to shift the register content to the right to get
the data into bit zero.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - maximum: 56
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 56
required:
- compatible
diff --git a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
index 01c7d93dc658..32e0896c6bc1 100644
--- a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
+++ b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
@@ -57,8 +57,7 @@ properties:
description: |
mA; per-string current limit.
This property is supported only for WLED3.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
default: 20
minimum: 0
maximum: 25
@@ -74,38 +73,33 @@ properties:
qcom,current-boost-limit:
description: |
mA; boost current limit.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
qcom,switching-freq:
description: |
kHz; switching frequency.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [ 600, 640, 685, 738, 800, 872, 960, 1066, 1200, 1371, 1600, 1920, 2400, 3200, 4800, 9600 ]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [ 600, 640, 685, 738, 800, 872, 960, 1066, 1200, 1371, 1600, 1920, 2400, 3200, 4800, 9600 ]
qcom,ovp:
description: |
V; Over-voltage protection limit.
This property is supported only for WLED3.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [ 27, 29, 32, 35 ]
- - default: 29
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [ 27, 29, 32, 35 ]
+ default: 29
qcom,ovp-millivolt:
description: |
Over-voltage protection limit. This property is for WLED4 only.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [ 18100, 19600, 29600, 31100 ]
- - default: 29600
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [ 18100, 19600, 29600, 31100 ]
+ default: 29600
qcom,num-strings:
description: |
number of led strings attached.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
qcom,enabled-strings:
description: |
@@ -113,8 +107,7 @@ properties:
string of leds are operated individually. Specify the
list of strings used by the device. Any combination of
led strings can be used.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
+ $ref: /schemas/types.yaml#/definitions/uint32-array
minItems: 1
maxItems: 4
@@ -150,10 +143,9 @@ properties:
0 - Modulator A
1 - Modulator B
This property is applicable only to WLED5 peripheral.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [ 0, 1 ]
- - default: 0
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [ 0, 1 ]
+ default: 0
qcom,cabc-sel:
description: |
@@ -164,9 +156,8 @@ properties:
2 - CABC 2
3 - External signal (e.g. LPG) is used for dimming
This property is applicable only to WLED5 peripheral.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [ 0, 1, 2, 3 ]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [ 0, 1, 2, 3 ]
allOf:
- if:
diff --git a/Documentation/devicetree/bindings/leds/leds-aw2013.yaml b/Documentation/devicetree/bindings/leds/leds-aw2013.yaml
index f118721df1e8..e24b0d15ef01 100644
--- a/Documentation/devicetree/bindings/leds/leds-aw2013.yaml
+++ b/Documentation/devicetree/bindings/leds/leds-aw2013.yaml
@@ -32,8 +32,7 @@ properties:
patternProperties:
"^led@[0-2]$":
type: object
- allOf:
- - $ref: common.yaml#
+ $ref: common.yaml#
properties:
reg:
diff --git a/Documentation/devicetree/bindings/leds/leds-sgm3140.yaml b/Documentation/devicetree/bindings/leds/leds-sgm3140.yaml
index ecf7ac9ab067..f68259619488 100644
--- a/Documentation/devicetree/bindings/leds/leds-sgm3140.yaml
+++ b/Documentation/devicetree/bindings/leds/leds-sgm3140.yaml
@@ -33,8 +33,7 @@ properties:
led:
type: object
- allOf:
- - $ref: common.yaml#
+ $ref: common.yaml#
required:
- compatible
diff --git a/Documentation/devicetree/bindings/media/i2c/ov8856.yaml b/Documentation/devicetree/bindings/media/i2c/ov8856.yaml
index d6af685ad3ca..1956b2a32bf4 100644
--- a/Documentation/devicetree/bindings/media/i2c/ov8856.yaml
+++ b/Documentation/devicetree/bindings/media/i2c/ov8856.yaml
@@ -79,8 +79,7 @@ properties:
- const: 4
link-frequencies:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint64-array
+ $ref: /schemas/types.yaml#/definitions/uint64-array
description:
Allowed data bus frequencies. 360000000, 180000000 Hz or both
are supported by the driver.
diff --git a/Documentation/devicetree/bindings/memory-controllers/ingenic,nemc.yaml b/Documentation/devicetree/bindings/memory-controllers/ingenic,nemc.yaml
index 9b478da0c479..17ba45a6c260 100644
--- a/Documentation/devicetree/bindings/memory-controllers/ingenic,nemc.yaml
+++ b/Documentation/devicetree/bindings/memory-controllers/ingenic,nemc.yaml
@@ -45,9 +45,8 @@ patternProperties:
maxItems: 255
ingenic,nemc-bus-width:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [8, 16]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [8, 16]
description: Specifies the bus width in bits.
ingenic,nemc-tAS:
diff --git a/Documentation/devicetree/bindings/net/ti,k3-am654-cpsw-nuss.yaml b/Documentation/devicetree/bindings/net/ti,k3-am654-cpsw-nuss.yaml
index 71d9e6c1c72e..174579370a22 100644
--- a/Documentation/devicetree/bindings/net/ti,k3-am654-cpsw-nuss.yaml
+++ b/Documentation/devicetree/bindings/net/ti,k3-am654-cpsw-nuss.yaml
@@ -145,8 +145,7 @@ patternProperties:
"^cpts@[0-9a-f]+":
type: object
- allOf:
- - $ref: "ti,k3-am654-cpts.yaml#"
+ $ref: "ti,k3-am654-cpts.yaml#"
description:
CPSW Common Platform Time Sync (CPTS) module.
diff --git a/Documentation/devicetree/bindings/net/ti,k3-am654-cpts.yaml b/Documentation/devicetree/bindings/net/ti,k3-am654-cpts.yaml
index 50e027911dd4..af608f2ecfdf 100644
--- a/Documentation/devicetree/bindings/net/ti,k3-am654-cpts.yaml
+++ b/Documentation/devicetree/bindings/net/ti,k3-am654-cpts.yaml
@@ -74,15 +74,13 @@ properties:
- const: cpts
ti,cpts-ext-ts-inputs:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
maximum: 8
description:
Number of hardware timestamp push inputs (HWx_TS_PUSH)
ti,cpts-periodic-outputs:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
maximum: 8
description:
Number of timestamp Generator function outputs (TS_GENFx)
diff --git a/Documentation/devicetree/bindings/pci/cdns-pcie-ep.yaml b/Documentation/devicetree/bindings/pci/cdns-pcie-ep.yaml
index 6150a7a7bdbf..016a5f61592d 100644
--- a/Documentation/devicetree/bindings/pci/cdns-pcie-ep.yaml
+++ b/Documentation/devicetree/bindings/pci/cdns-pcie-ep.yaml
@@ -15,8 +15,7 @@ allOf:
properties:
cdns,max-outbound-regions:
description: maximum number of outbound regions
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
minimum: 1
maximum: 32
default: 32
diff --git a/Documentation/devicetree/bindings/pci/cdns-pcie-host.yaml b/Documentation/devicetree/bindings/pci/cdns-pcie-host.yaml
index c87a3a36ccd2..303078a7b7a8 100644
--- a/Documentation/devicetree/bindings/pci/cdns-pcie-host.yaml
+++ b/Documentation/devicetree/bindings/pci/cdns-pcie-host.yaml
@@ -16,8 +16,7 @@ allOf:
properties:
cdns,max-outbound-regions:
description: maximum number of outbound regions
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
minimum: 1
maximum: 32
default: 32
diff --git a/Documentation/devicetree/bindings/phy/calxeda-combophy.yaml b/Documentation/devicetree/bindings/phy/calxeda-combophy.yaml
index 16a8bd7644bf..41ee16e21f8d 100644
--- a/Documentation/devicetree/bindings/phy/calxeda-combophy.yaml
+++ b/Documentation/devicetree/bindings/phy/calxeda-combophy.yaml
@@ -29,9 +29,8 @@ properties:
phydev:
description: device ID for programming the ComboPHY.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - maximum: 31
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 31
required:
- compatible
diff --git a/Documentation/devicetree/bindings/phy/renesas,usb3-phy.yaml b/Documentation/devicetree/bindings/phy/renesas,usb3-phy.yaml
index f459eaf55278..68cf9dd0390d 100644
--- a/Documentation/devicetree/bindings/phy/renesas,usb3-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/renesas,usb3-phy.yaml
@@ -52,9 +52,8 @@ properties:
description: |
Enable/disable spread spectrum clock (ssc). 0 or the property doesn't
exist means disabling the ssc. The actual value will be -<value> ppm.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [ 0, 4003, 4492, 4980 ]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [ 0, 4003, 4492, 4980 ]
required:
- compatible
diff --git a/Documentation/devicetree/bindings/power/supply/cw2015_battery.yaml b/Documentation/devicetree/bindings/power/supply/cw2015_battery.yaml
index 4a265d4234b9..2036977ecc2f 100644
--- a/Documentation/devicetree/bindings/power/supply/cw2015_battery.yaml
+++ b/Documentation/devicetree/bindings/power/supply/cw2015_battery.yaml
@@ -27,11 +27,9 @@ properties:
of this binary blob is kept secret by CellWise. The only way to obtain
it is to mail two batteries to a test facility of CellWise and receive
back a test report with the binary blob.
- allOf:
- - $ref: /schemas/types.yaml#definitions/uint8-array
- items:
- - minItems: 64
- maxItems: 64
+ $ref: /schemas/types.yaml#definitions/uint8-array
+ minItems: 64
+ maxItems: 64
cellwise,monitor-interval-ms:
description:
@@ -41,10 +39,9 @@ properties:
power-supplies:
description:
Specifies supplies used for charging the battery connected to this gauge
- allOf:
- - $ref: /schemas/types.yaml#/definitions/phandle-array
- - minItems: 1
- maxItems: 8 # Should be enough
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ minItems: 1
+ maxItems: 8 # Should be enough
monitored-battery:
description:
diff --git a/Documentation/devicetree/bindings/power/supply/sbs,sbs-battery.yaml b/Documentation/devicetree/bindings/power/supply/sbs,sbs-battery.yaml
index 205bc826bd20..a90b3601e695 100644
--- a/Documentation/devicetree/bindings/power/supply/sbs,sbs-battery.yaml
+++ b/Documentation/devicetree/bindings/power/supply/sbs,sbs-battery.yaml
@@ -32,16 +32,14 @@ properties:
description:
The number of times to retry I2C transactions on I2C IO failure.
default: 0
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
sbs,poll-retry-count:
description:
The number of times to try looking for new status after an external
change notification.
default: 0
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
sbs,battery-detect-gpios:
description:
diff --git a/Documentation/devicetree/bindings/regulator/maxim,max77826.yaml b/Documentation/devicetree/bindings/regulator/maxim,max77826.yaml
index 19cbd5eb2897..78c0b63243f7 100644
--- a/Documentation/devicetree/bindings/regulator/maxim,max77826.yaml
+++ b/Documentation/devicetree/bindings/regulator/maxim,max77826.yaml
@@ -21,8 +21,7 @@ properties:
regulators:
type: object
- allOf:
- - $ref: regulator.yaml#
+ $ref: regulator.yaml#
description: |
list of regulators provided by this controller, must be named
after their hardware counterparts LDO[1-15], BUCK and BUCKBOOST
@@ -30,13 +29,11 @@ properties:
patternProperties:
"^LDO([1-9]|1[0-5])$":
type: object
- allOf:
- - $ref: regulator.yaml#
+ $ref: regulator.yaml#
"^BUCK|BUCKBOOST$":
type: object
- allOf:
- - $ref: regulator.yaml#
+ $ref: regulator.yaml#
additionalProperties: false
diff --git a/Documentation/devicetree/bindings/regulator/rohm,bd71847-regulator.yaml b/Documentation/devicetree/bindings/regulator/rohm,bd71847-regulator.yaml
index d797cc23406f..07256a4b50b9 100644
--- a/Documentation/devicetree/bindings/regulator/rohm,bd71847-regulator.yaml
+++ b/Documentation/devicetree/bindings/regulator/rohm,bd71847-regulator.yaml
@@ -29,8 +29,7 @@ description: |
patternProperties:
"^LDO[1-6]$":
type: object
- allOf:
- - $ref: regulator.yaml#
+ $ref: regulator.yaml#
description:
Properties for single LDO regulator.
@@ -44,8 +43,7 @@ patternProperties:
"^BUCK[1-6]$":
type: object
- allOf:
- - $ref: regulator.yaml#
+ $ref: regulator.yaml#
description:
Properties for single BUCK regulator.
@@ -56,28 +54,25 @@ patternProperties:
should be "buck1", ..., "buck6"
rohm,dvs-run-voltage:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 0
- maximum: 1300000
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 1300000
description:
PMIC default "RUN" state voltage in uV. See below table for
bucks which support this. 0 means disabled.
rohm,dvs-idle-voltage:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 0
- maximum: 1300000
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 1300000
description:
PMIC default "IDLE" state voltage in uV. See below table for
bucks which support this. 0 means disabled.
rohm,dvs-suspend-voltage:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 0
- maximum: 1300000
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 1300000
description:
PMIC default "SUSPEND" state voltage in uV. See below table for
bucks which support this. 0 means disabled.
diff --git a/Documentation/devicetree/bindings/rng/arm-cctrng.yaml b/Documentation/devicetree/bindings/rng/arm-cctrng.yaml
index ca6aad19b6ba..c471e4c10558 100644
--- a/Documentation/devicetree/bindings/rng/arm-cctrng.yaml
+++ b/Documentation/devicetree/bindings/rng/arm-cctrng.yaml
@@ -28,10 +28,8 @@ properties:
description:
Arm TrustZone CryptoCell TRNG engine has 4 ring oscillators.
Sampling ratio values for these 4 ring oscillators. (from calibration)
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - items:
- maxItems: 4
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ maxItems: 4
clocks:
maxItems: 1
diff --git a/Documentation/devicetree/bindings/serial/samsung_uart.yaml b/Documentation/devicetree/bindings/serial/samsung_uart.yaml
index 32a5e1e30833..96414ac65d06 100644
--- a/Documentation/devicetree/bindings/serial/samsung_uart.yaml
+++ b/Documentation/devicetree/bindings/serial/samsung_uart.yaml
@@ -33,9 +33,8 @@ properties:
description: |
The size (in bytes) of the IO accesses that should be performed
on the device.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [ 1, 4 ]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [ 1, 4 ]
clocks:
minItems: 2
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.yaml
index dee8bb2b69fe..a2b29cc3e93b 100644
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.yaml
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.yaml
@@ -100,8 +100,7 @@ patternProperties:
supports up to 50MHz, up to four chip selects, programmable
data path from 4 bits to 32 bits and numerous protocol
variants.
- allOf:
- - $ref: /spi/spi-controller.yaml#
+ $ref: /spi/spi-controller.yaml#
properties:
compatible:
@@ -126,8 +125,7 @@ patternProperties:
"i2c@[0-9a-f]+$":
type: object
description: GENI serial engine based I2C controller.
- allOf:
- - $ref: /schemas/i2c/i2c-controller.yaml#
+ $ref: /schemas/i2c/i2c-controller.yaml#
properties:
compatible:
@@ -156,8 +154,7 @@ patternProperties:
"serial@[0-9a-f]+$":
type: object
description: GENI Serial Engine based UART Controller.
- allOf:
- - $ref: /schemas/serial.yaml#
+ $ref: /schemas/serial.yaml#
properties:
compatible:
diff --git a/Documentation/devicetree/bindings/sound/fsl,easrc.yaml b/Documentation/devicetree/bindings/sound/fsl,easrc.yaml
index 73cdcf053a9c..9dd57a974b28 100644
--- a/Documentation/devicetree/bindings/sound/fsl,easrc.yaml
+++ b/Documentation/devicetree/bindings/sound/fsl,easrc.yaml
@@ -45,23 +45,20 @@ properties:
- const: ctx3_tx
firmware-name:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/string
- - const: imx/easrc/easrc-imx8mn.bin
+ $ref: /schemas/types.yaml#/definitions/string
+ const: imx/easrc/easrc-imx8mn.bin
description: The coefficient table for the filters
fsl,asrc-rate:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 8000
- - maximum: 192000
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 8000
+ maximum: 192000
description: Defines a mutual sample rate used by DPCM Back Ends
fsl,asrc-format:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [2, 6, 10, 32, 36]
- default: 2
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [2, 6, 10, 32, 36]
+ default: 2
description:
Defines a mutual sample format used by DPCM Back Ends
diff --git a/Documentation/devicetree/bindings/sound/simple-card.yaml b/Documentation/devicetree/bindings/sound/simple-card.yaml
index cb2bb5fac0e1..8132d0c0f00a 100644
--- a/Documentation/devicetree/bindings/sound/simple-card.yaml
+++ b/Documentation/devicetree/bindings/sound/simple-card.yaml
@@ -13,15 +13,13 @@ definitions:
frame-master:
description: Indicates dai-link frame master.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/phandle-array
- - maxItems: 1
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ maxItems: 1
bitclock-master:
description: Indicates dai-link bit clock master
- allOf:
- - $ref: /schemas/types.yaml#/definitions/phandle-array
- - maxItems: 1
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ maxItems: 1
frame-inversion:
description: dai-link uses frame clock inversion
diff --git a/Documentation/devicetree/bindings/sound/tlv320adcx140.yaml b/Documentation/devicetree/bindings/sound/tlv320adcx140.yaml
index c5b5b4260496..2e6ac5d2ee96 100644
--- a/Documentation/devicetree/bindings/sound/tlv320adcx140.yaml
+++ b/Documentation/devicetree/bindings/sound/tlv320adcx140.yaml
@@ -76,13 +76,12 @@ properties:
PDMIN3 - PDMCLK latching edge used for channel 5 and 6 data
PDMIN4 - PDMCLK latching edge used for channel 7 and 8 data
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - minItems: 1
- maxItems: 4
- items:
- maximum: 1
- default: [0, 0, 0, 0]
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 1
+ maxItems: 4
+ items:
+ maximum: 1
+ default: [0, 0, 0, 0]
ti,gpi-config:
description: |
@@ -102,13 +101,12 @@ properties:
7 - GPIX is configured as a PDM data input for channel 7 and channel
(PDMDIN4)
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - minItems: 1
- maxItems: 4
- items:
- maximum: 7
- default: [0, 0, 0, 0]
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 1
+ maxItems: 4
+ items:
+ maximum: 7
+ default: [0, 0, 0, 0]
required:
- compatible
diff --git a/Documentation/devicetree/bindings/thermal/socionext,uniphier-thermal.yaml b/Documentation/devicetree/bindings/thermal/socionext,uniphier-thermal.yaml
index bb9594bb2cf1..553c9dcdaeeb 100644
--- a/Documentation/devicetree/bindings/thermal/socionext,uniphier-thermal.yaml
+++ b/Documentation/devicetree/bindings/thermal/socionext,uniphier-thermal.yaml
@@ -28,9 +28,8 @@ properties:
const: 0
socionext,tmod-calibration:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - maxItems: 2
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ maxItems: 2
description:
A pair of calibrated values referred from PVT, in case that the values
aren't set on SoC, like a reference board.
diff --git a/Documentation/devicetree/bindings/usb/aspeed,usb-vhub.yaml b/Documentation/devicetree/bindings/usb/aspeed,usb-vhub.yaml
index ccc67d03d4bb..e4e83d3971ac 100644
--- a/Documentation/devicetree/bindings/usb/aspeed,usb-vhub.yaml
+++ b/Documentation/devicetree/bindings/usb/aspeed,usb-vhub.yaml
@@ -52,21 +52,18 @@ properties:
vhub-vendor-id:
description: vhub Vendor ID
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - maximum: 65535
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 65535
vhub-product-id:
description: vhub Product ID
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - maximum: 65535
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 65535
vhub-device-revision:
description: vhub Device Revision in binary-coded decimal
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - maximum: 65535
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 65535
vhub-strings:
type: object
@@ -90,18 +87,15 @@ properties:
manufacturer:
description: vhub manufacturer
- allOf:
- - $ref: /schemas/types.yaml#/definitions/string
+ $ref: /schemas/types.yaml#/definitions/string
product:
description: vhub product name
- allOf:
- - $ref: /schemas/types.yaml#/definitions/string
+ $ref: /schemas/types.yaml#/definitions/string
serial-number:
description: vhub device serial number
- allOf:
- - $ref: /schemas/types.yaml#/definitions/string
+ $ref: /schemas/types.yaml#/definitions/string
required:
- compatible
diff --git a/Documentation/devicetree/bindings/watchdog/arm-smc-wdt.yaml b/Documentation/devicetree/bindings/watchdog/arm-smc-wdt.yaml
index bec651541e0c..8e4c7c69bc1c 100644
--- a/Documentation/devicetree/bindings/watchdog/arm-smc-wdt.yaml
+++ b/Documentation/devicetree/bindings/watchdog/arm-smc-wdt.yaml
@@ -17,8 +17,7 @@ properties:
enum:
- arm,smc-wdt
arm,smc-id:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
description: |
The ATF smc function id used by the firmware.
Defaults to 0x82003D06 if unset.
--
2.25.1
^ permalink raw reply related [flat|nested] 2+ messages in thread
* [PATCH] dt-bindings: Remove more cases of 'allOf' containing a '$ref'
@ 2020-08-14 16:21 Rob Herring
0 siblings, 0 replies; 2+ messages in thread
From: Rob Herring @ 2020-08-14 16:21 UTC (permalink / raw)
To: devicetree; +Cc: linux-kernel
Another wack-a-mole pass of killing off unnecessary 'allOf + $ref'
usage.
json-schema versions draft7 and earlier have a weird behavior in that
any keywords combined with a '$ref' are ignored (silently). The correct
form was to put a '$ref' under an 'allOf'. This behavior is now changed
in the 2019-09 json-schema spec and '$ref' can be mixed with other
keywords. The json-schema library doesn't yet support this, but the
tooling now does a fixup for this and either way works.
This has been a constant source of review comments, so let's change this
treewide so everyone copies the simpler syntax.
Signed-off-by: Rob Herring <robh@kernel.org>
---
.../bindings/display/brcm,bcm2835-hdmi.yaml | 3 +-
.../bindings/iio/adc/qcom,spmi-vadc.yaml | 3 +-
.../interrupt-controller/mti,gic.yaml | 28 ++++++------
.../bindings/media/i2c/dongwoon,dw9768.yaml | 43 +++++++++----------
.../bindings/pci/ti,j721e-pci-ep.yaml | 3 +-
.../bindings/pci/ti,j721e-pci-host.yaml | 3 +-
.../bindings/sound/maxim,max98390.yaml | 6 +--
.../bindings/sound/nvidia,tegra186-dspk.yaml | 3 +-
.../bindings/sound/nvidia,tegra210-dmic.yaml | 3 +-
.../bindings/sound/nvidia,tegra210-i2s.yaml | 3 +-
.../bindings/sound/ti,j721e-cpb-audio.yaml | 6 +--
.../sound/ti,j721e-cpb-ivi-audio.yaml | 15 +++----
12 files changed, 49 insertions(+), 70 deletions(-)
diff --git a/Documentation/devicetree/bindings/display/brcm,bcm2835-hdmi.yaml b/Documentation/devicetree/bindings/display/brcm,bcm2835-hdmi.yaml
index 52b3cdac0bdf..f54b4e4808f0 100644
--- a/Documentation/devicetree/bindings/display/brcm,bcm2835-hdmi.yaml
+++ b/Documentation/devicetree/bindings/display/brcm,bcm2835-hdmi.yaml
@@ -32,8 +32,7 @@ properties:
- const: hdmi
ddc:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/phandle
+ $ref: /schemas/types.yaml#/definitions/phandle
description: >
Phandle of the I2C controller used for DDC EDID probing
diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
index a6ac289d98da..0ca992465a21 100644
--- a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
+++ b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
@@ -97,8 +97,7 @@ patternProperties:
input signal is multiplied. For example, <1 3> indicates the signal is scaled
down to 1/3 of its value before ADC measurement.
If property is not found default value depending on chip will be used.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
+ $ref: /schemas/types.yaml#/definitions/uint32-array
oneOf:
- items:
- const: 1
diff --git a/Documentation/devicetree/bindings/interrupt-controller/mti,gic.yaml b/Documentation/devicetree/bindings/interrupt-controller/mti,gic.yaml
index 9f0eb3addac4..ce6aaff15214 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/mti,gic.yaml
+++ b/Documentation/devicetree/bindings/interrupt-controller/mti,gic.yaml
@@ -42,14 +42,13 @@ properties:
Specifies the list of CPU interrupt vectors to which the GIC may not
route interrupts. This property is ignored if the CPU is started in EIC
mode.
- allOf:
- - $ref: /schemas/types.yaml#definitions/uint32-array
- - minItems: 1
- maxItems: 6
- uniqueItems: true
- items:
- minimum: 2
- maximum: 7
+ $ref: /schemas/types.yaml#definitions/uint32-array
+ minItems: 1
+ maxItems: 6
+ uniqueItems: true
+ items:
+ minimum: 2
+ maximum: 7
mti,reserved-ipi-vectors:
description: |
@@ -57,13 +56,12 @@ properties:
It accepts two values: the 1st is the starting interrupt and the 2nd is
the size of the reserved range. If not specified, the driver will
allocate the last (2 * number of VPEs in the system).
- allOf:
- - $ref: /schemas/types.yaml#definitions/uint32-array
- - items:
- - minimum: 0
- maximum: 254
- - minimum: 2
- maximum: 254
+ $ref: /schemas/types.yaml#definitions/uint32-array
+ items:
+ - minimum: 0
+ maximum: 254
+ - minimum: 2
+ maximum: 254
timer:
type: object
diff --git a/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9768.yaml b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9768.yaml
index cb96e95d7e81..21864ab86ec4 100644
--- a/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9768.yaml
+++ b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9768.yaml
@@ -38,39 +38,36 @@ properties:
dongwoon,aac-mode:
description:
Indication of AAC mode select.
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - enum:
- - 1 # AAC2 mode(operation time# 0.48 x Tvib)
- - 2 # AAC3 mode(operation time# 0.70 x Tvib)
- - 3 # AAC4 mode(operation time# 0.75 x Tvib)
- - 5 # AAC8 mode(operation time# 1.13 x Tvib)
- default: 2
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ enum:
+ - 1 # AAC2 mode(operation time# 0.48 x Tvib)
+ - 2 # AAC3 mode(operation time# 0.70 x Tvib)
+ - 3 # AAC4 mode(operation time# 0.75 x Tvib)
+ - 5 # AAC8 mode(operation time# 1.13 x Tvib)
+ default: 2
dongwoon,aac-timing:
description:
Number of AAC Timing count that controlled by one 6-bit period of
vibration register AACT[5:0], the unit of which is 100 us.
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - default: 0x20
- minimum: 0x00
- maximum: 0x3f
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ default: 0x20
+ minimum: 0x00
+ maximum: 0x3f
dongwoon,clock-presc:
description:
Indication of VCM internal clock dividing rate select, as one multiple
factor to calculate VCM ring periodic time Tvib.
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - enum:
- - 0 # Dividing Rate - 2
- - 1 # Dividing Rate - 1
- - 2 # Dividing Rate - 1/2
- - 3 # Dividing Rate - 1/4
- - 4 # Dividing Rate - 8
- - 5 # Dividing Rate - 4
- default: 1
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ enum:
+ - 0 # Dividing Rate - 2
+ - 1 # Dividing Rate - 1
+ - 2 # Dividing Rate - 1/2
+ - 3 # Dividing Rate - 1/4
+ - 4 # Dividing Rate - 8
+ - 5 # Dividing Rate - 4
+ default: 1
required:
- compatible
diff --git a/Documentation/devicetree/bindings/pci/ti,j721e-pci-ep.yaml b/Documentation/devicetree/bindings/pci/ti,j721e-pci-ep.yaml
index cfe25cface21..b3c3d0c3c390 100644
--- a/Documentation/devicetree/bindings/pci/ti,j721e-pci-ep.yaml
+++ b/Documentation/devicetree/bindings/pci/ti,j721e-pci-ep.yaml
@@ -31,8 +31,7 @@ properties:
ti,syscon-pcie-ctrl:
description: Phandle to the SYSCON entry required for configuring PCIe mode
and link speed.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/phandle
+ $ref: /schemas/types.yaml#/definitions/phandle
power-domains:
maxItems: 1
diff --git a/Documentation/devicetree/bindings/pci/ti,j721e-pci-host.yaml b/Documentation/devicetree/bindings/pci/ti,j721e-pci-host.yaml
index d7b60487c6c3..8200ba00bc09 100644
--- a/Documentation/devicetree/bindings/pci/ti,j721e-pci-host.yaml
+++ b/Documentation/devicetree/bindings/pci/ti,j721e-pci-host.yaml
@@ -31,8 +31,7 @@ properties:
ti,syscon-pcie-ctrl:
description: Phandle to the SYSCON entry required for configuring PCIe mode
and link speed.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/phandle
+ $ref: /schemas/types.yaml#/definitions/phandle
power-domains:
maxItems: 1
diff --git a/Documentation/devicetree/bindings/sound/maxim,max98390.yaml b/Documentation/devicetree/bindings/sound/maxim,max98390.yaml
index 9c2e3effa0c0..fea9a1b6619a 100644
--- a/Documentation/devicetree/bindings/sound/maxim,max98390.yaml
+++ b/Documentation/devicetree/bindings/sound/maxim,max98390.yaml
@@ -18,16 +18,14 @@ properties:
description: I2C address of the device.
maxim,temperature_calib:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
description: The calculated temperature data was measured while doing the calibration.
+ $ref: /schemas/types.yaml#/definitions/uint32
minimum: 0
maximum: 65535
maxim,r0_calib:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
description: This is r0 calibration data which was measured in factory mode.
+ $ref: /schemas/types.yaml#/definitions/uint32
minimum: 1
maximum: 8388607
diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra186-dspk.yaml b/Documentation/devicetree/bindings/sound/nvidia,tegra186-dspk.yaml
index e620c77d0728..2f2fcffa65cb 100644
--- a/Documentation/devicetree/bindings/sound/nvidia,tegra186-dspk.yaml
+++ b/Documentation/devicetree/bindings/sound/nvidia,tegra186-dspk.yaml
@@ -48,8 +48,7 @@ properties:
sound-name-prefix:
pattern: "^DSPK[1-9]$"
- allOf:
- - $ref: /schemas/types.yaml#/definitions/string
+ $ref: /schemas/types.yaml#/definitions/string
description:
Used as prefix for sink/source names of the component. Must be a
unique string among multiple instances of the same component.
diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra210-dmic.yaml b/Documentation/devicetree/bindings/sound/nvidia,tegra210-dmic.yaml
index 1c14e83f67c7..8689d9f18c11 100644
--- a/Documentation/devicetree/bindings/sound/nvidia,tegra210-dmic.yaml
+++ b/Documentation/devicetree/bindings/sound/nvidia,tegra210-dmic.yaml
@@ -49,8 +49,7 @@ properties:
sound-name-prefix:
pattern: "^DMIC[1-9]$"
- allOf:
- - $ref: /schemas/types.yaml#/definitions/string
+ $ref: /schemas/types.yaml#/definitions/string
description:
used as prefix for sink/source names of the component. Must be a
unique string among multiple instances of the same component.
diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra210-i2s.yaml b/Documentation/devicetree/bindings/sound/nvidia,tegra210-i2s.yaml
index 795797001843..9bbf18153d63 100644
--- a/Documentation/devicetree/bindings/sound/nvidia,tegra210-i2s.yaml
+++ b/Documentation/devicetree/bindings/sound/nvidia,tegra210-i2s.yaml
@@ -67,8 +67,7 @@ properties:
sound-name-prefix:
pattern: "^I2S[1-9]$"
- allOf:
- - $ref: /schemas/types.yaml#/definitions/string
+ $ref: /schemas/types.yaml#/definitions/string
description:
Used as prefix for sink/source names of the component. Must be a
unique string among multiple instances of the same component.
diff --git a/Documentation/devicetree/bindings/sound/ti,j721e-cpb-audio.yaml b/Documentation/devicetree/bindings/sound/ti,j721e-cpb-audio.yaml
index 6f2be6503401..d52cfbeb2d07 100644
--- a/Documentation/devicetree/bindings/sound/ti,j721e-cpb-audio.yaml
+++ b/Documentation/devicetree/bindings/sound/ti,j721e-cpb-audio.yaml
@@ -37,13 +37,11 @@ properties:
ti,cpb-mcasp:
description: phandle to McASP used on CPB
- allOf:
- - $ref: /schemas/types.yaml#/definitions/phandle
+ $ref: /schemas/types.yaml#/definitions/phandle
ti,cpb-codec:
description: phandle to the pcm3168a codec used on the CPB
- allOf:
- - $ref: /schemas/types.yaml#/definitions/phandle
+ $ref: /schemas/types.yaml#/definitions/phandle
clocks:
items:
diff --git a/Documentation/devicetree/bindings/sound/ti,j721e-cpb-ivi-audio.yaml b/Documentation/devicetree/bindings/sound/ti,j721e-cpb-ivi-audio.yaml
index e0b88470a502..bb780f621628 100644
--- a/Documentation/devicetree/bindings/sound/ti,j721e-cpb-ivi-audio.yaml
+++ b/Documentation/devicetree/bindings/sound/ti,j721e-cpb-ivi-audio.yaml
@@ -50,28 +50,23 @@ properties:
ti,cpb-mcasp:
description: phandle to McASP used on CPB
- allOf:
- - $ref: /schemas/types.yaml#/definitions/phandle
+ $ref: /schemas/types.yaml#/definitions/phandle
ti,cpb-codec:
description: phandle to the pcm3168a codec used on the CPB
- allOf:
- - $ref: /schemas/types.yaml#/definitions/phandle
+ $ref: /schemas/types.yaml#/definitions/phandle
ti,ivi-mcasp:
description: phandle to McASP used on IVI
- allOf:
- - $ref: /schemas/types.yaml#/definitions/phandle
+ $ref: /schemas/types.yaml#/definitions/phandle
ti,ivi-codec-a:
description: phandle to the pcm3168a-A codec on the expansion board
- allOf:
- - $ref: /schemas/types.yaml#/definitions/phandle
+ $ref: /schemas/types.yaml#/definitions/phandle
ti,ivi-codec-b:
description: phandle to the pcm3168a-B codec on the expansion board
- allOf:
- - $ref: /schemas/types.yaml#/definitions/phandle
+ $ref: /schemas/types.yaml#/definitions/phandle
clocks:
items:
--
2.25.1
^ permalink raw reply related [flat|nested] 2+ messages in thread
end of thread, other threads:[~2020-08-14 16:21 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-06-11 15:20 [PATCH] dt-bindings: Remove more cases of 'allOf' containing a '$ref' Rob Herring
2020-08-14 16:21 Rob Herring
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).