From: "周琰杰 (Zhou Yanjie)" <zhouyanjie@wanyeetech.com>
To: tsbogend@alpha.franken.de, robh+dt@kernel.org
Cc: linux-mips@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, paulburton@kernel.org,
paul@crapouillou.net, ak@linux.intel.com, ebiederm@xmission.com,
dongsheng.qiu@ingenic.com, aric.pzqi@ingenic.com,
rick.tyliu@ingenic.com, yanfei.li@ingenic.com,
sernia.zhou@foxmail.com, zhenwenjin@gmail.com
Subject: [PATCH v4 1/5] MIPS: Ingenic: Add Ingenic X1830 support.
Date: Tue, 14 Jul 2020 13:32:25 +0800 [thread overview]
Message-ID: <20200714053229.33195-2-zhouyanjie@wanyeetech.com> (raw)
In-Reply-To: <20200714053229.33195-1-zhouyanjie@wanyeetech.com>
Support the Ingenic X1830 SoC using the code under arch/mips/jz4740.
This is left unselectable in Kconfig until a X1830 based board is
added in a later commit.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
---
Notes:
v1->v2:
No change.
v2->v3:
Adjust the order of nodes according to the
corresponding address value.
v3->v4:
No change.
arch/mips/boot/dts/ingenic/x1830.dtsi | 300 ++++++++++++++++++++++++++++++++++
arch/mips/jz4740/Kconfig | 6 +
2 files changed, 306 insertions(+)
create mode 100644 arch/mips/boot/dts/ingenic/x1830.dtsi
diff --git a/arch/mips/boot/dts/ingenic/x1830.dtsi b/arch/mips/boot/dts/ingenic/x1830.dtsi
new file mode 100644
index 000000000000..eb1214481a33
--- /dev/null
+++ b/arch/mips/boot/dts/ingenic/x1830.dtsi
@@ -0,0 +1,300 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/clock/ingenic,tcu.h>
+#include <dt-bindings/clock/x1830-cgu.h>
+#include <dt-bindings/dma/x1830-dma.h>
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "ingenic,x1830";
+
+ cpuintc: interrupt-controller {
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ compatible = "mti,cpu-interrupt-controller";
+ };
+
+ intc: interrupt-controller@10001000 {
+ compatible = "ingenic,x1830-intc", "ingenic,jz4780-intc";
+ reg = <0x10001000 0x50>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ interrupt-parent = <&cpuintc>;
+ interrupts = <2>;
+ };
+
+ exclk: ext {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ };
+
+ rtclk: rtc {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ };
+
+ cgu: x1830-cgu@10000000 {
+ compatible = "ingenic,x1830-cgu";
+ reg = <0x10000000 0x100>;
+
+ #clock-cells = <1>;
+
+ clocks = <&exclk>, <&rtclk>;
+ clock-names = "ext", "rtc";
+ };
+
+ tcu: timer@10002000 {
+ compatible = "ingenic,x1830-tcu", "ingenic,x1000-tcu", "simple-mfd";
+ reg = <0x10002000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x10002000 0x1000>;
+
+ #clock-cells = <1>;
+
+ clocks = <&cgu X1830_CLK_RTCLK
+ &cgu X1830_CLK_EXCLK
+ &cgu X1830_CLK_PCLK>;
+ clock-names = "rtc", "ext", "pclk";
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <27 26 25>;
+
+ wdt: watchdog@0 {
+ compatible = "ingenic,x1830-watchdog", "ingenic,jz4780-watchdog";
+ reg = <0x0 0x10>;
+
+ clocks = <&tcu TCU_CLK_WDT>;
+ clock-names = "wdt";
+ };
+ };
+
+ rtc: rtc@10003000 {
+ compatible = "ingenic,x1830-rtc", "ingenic,jz4780-rtc";
+ reg = <0x10003000 0x4c>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <32>;
+
+ clocks = <&cgu X1830_CLK_RTCLK>;
+ clock-names = "rtc";
+ };
+
+ pinctrl: pin-controller@10010000 {
+ compatible = "ingenic,x1830-pinctrl";
+ reg = <0x10010000 0x800>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpa: gpio@0 {
+ compatible = "ingenic,x1830-gpio";
+ reg = <0>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 0 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <17>;
+ };
+
+ gpb: gpio@1 {
+ compatible = "ingenic,x1830-gpio";
+ reg = <1>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 32 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <16>;
+ };
+
+ gpc: gpio@2 {
+ compatible = "ingenic,x1830-gpio";
+ reg = <2>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 64 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <15>;
+ };
+
+ gpd: gpio@3 {
+ compatible = "ingenic,x1830-gpio";
+ reg = <3>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 96 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <14>;
+ };
+ };
+
+ uart0: serial@10030000 {
+ compatible = "ingenic,x1830-uart", "ingenic,x1000-uart";
+ reg = <0x10030000 0x100>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <51>;
+
+ clocks = <&exclk>, <&cgu X1830_CLK_UART0>;
+ clock-names = "baud", "module";
+
+ status = "disabled";
+ };
+
+ uart1: serial@10031000 {
+ compatible = "ingenic,x1830-uart", "ingenic,x1000-uart";
+ reg = <0x10031000 0x100>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <50>;
+
+ clocks = <&exclk>, <&cgu X1830_CLK_UART1>;
+ clock-names = "baud", "module";
+
+ status = "disabled";
+ };
+
+ i2c0: i2c-controller@10050000 {
+ compatible = "ingenic,x1830-i2c", "ingenic,x1000-i2c";
+ reg = <0x10050000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <60>;
+
+ clocks = <&cgu X1830_CLK_SMB0>;
+
+ status = "disabled";
+ };
+
+ i2c1: i2c-controller@10051000 {
+ compatible = "ingenic,x1830-i2c", "ingenic,x1000-i2c";
+ reg = <0x10051000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <59>;
+
+ clocks = <&cgu X1830_CLK_SMB1>;
+
+ status = "disabled";
+ };
+
+ i2c2: i2c-controller@10052000 {
+ compatible = "ingenic,x1830-i2c", "ingenic,x1000-i2c";
+ reg = <0x10052000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <58>;
+
+ clocks = <&cgu X1830_CLK_SMB2>;
+
+ status = "disabled";
+ };
+
+ pdma: dma-controller@13420000 {
+ compatible = "ingenic,x1830-dma";
+ reg = <0x13420000 0x400
+ 0x13421000 0x40>;
+ #dma-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <10>;
+
+ clocks = <&cgu X1830_CLK_PDMA>;
+ };
+
+ msc0: mmc@13450000 {
+ compatible = "ingenic,x1830-mmc", "ingenic,x1000-mmc";
+ reg = <0x13450000 0x1000>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <37>;
+
+ clocks = <&cgu X1830_CLK_MSC0>;
+ clock-names = "mmc";
+
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ cap-sdio-irq;
+
+ dmas = <&pdma X1830_DMA_MSC0_RX 0xffffffff>,
+ <&pdma X1830_DMA_MSC0_TX 0xffffffff>;
+ dma-names = "rx", "tx";
+
+ status = "disabled";
+ };
+
+ msc1: mmc@13460000 {
+ compatible = "ingenic,x1830-mmc", "ingenic,x1000-mmc";
+ reg = <0x13460000 0x1000>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <36>;
+
+ clocks = <&cgu X1830_CLK_MSC1>;
+ clock-names = "mmc";
+
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ cap-sdio-irq;
+
+ dmas = <&pdma X1830_DMA_MSC1_RX 0xffffffff>,
+ <&pdma X1830_DMA_MSC1_TX 0xffffffff>;
+ dma-names = "rx", "tx";
+
+ status = "disabled";
+ };
+
+ mac: ethernet@134b0000 {
+ compatible = "ingenic,x1830-mac", "snps,dwmac";
+ reg = <0x134b0000 0x2000>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <55>;
+ interrupt-names = "macirq";
+
+ clocks = <&cgu X1830_CLK_MAC>;
+ clock-names = "stmmaceth";
+
+ status = "disabled";
+
+ mdio: mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+ };
+ };
+};
diff --git a/arch/mips/jz4740/Kconfig b/arch/mips/jz4740/Kconfig
index 9c2e8c15bb97..cd0ddb52da99 100644
--- a/arch/mips/jz4740/Kconfig
+++ b/arch/mips/jz4740/Kconfig
@@ -50,3 +50,9 @@ config MACH_X1000
select MIPS_CPU_SCACHE
select SYS_HAS_CPU_MIPS32_R2
select SYS_SUPPORTS_HIGHMEM
+
+config MACH_X1830
+ bool
+ select MIPS_CPU_SCACHE
+ select SYS_HAS_CPU_MIPS32_R2
+ select SYS_SUPPORTS_HIGHMEM
--
2.11.0
next prev parent reply other threads:[~2020-07-14 5:33 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-07-14 5:32 [PATCH v4 0/5] Add support for Ingenic X1830 SoC and Y&A CU1830-Neo board 周琰杰 (Zhou Yanjie)
2020-07-14 5:32 ` 周琰杰 (Zhou Yanjie) [this message]
2020-07-14 5:32 ` [PATCH v4 2/5] dt-bindings: MIPS: Add X1830 based CU1830-Neo and fix bug in CU1000-Neo 周琰杰 (Zhou Yanjie)
2020-07-14 20:49 ` Rob Herring
2020-07-14 5:32 ` [PATCH v4 3/5] MIPS: Ingenic: Add YSH & ATIL CU Neo board support 周琰杰 (Zhou Yanjie)
2020-07-14 5:32 ` [PATCH v4 4/5] MIPS: Ingenic: Fix bugs and add missing LED node for X1000 周琰杰 (Zhou Yanjie)
2020-07-14 5:32 ` [PATCH v4 5/5] MIPS: CU1000-Neo: Refresh defconfig to support LED 周琰杰 (Zhou Yanjie)
2020-07-16 9:51 ` [PATCH v4 0/5] Add support for Ingenic X1830 SoC and Y&A CU1830-Neo board Thomas Bogendoerfer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200714053229.33195-2-zhouyanjie@wanyeetech.com \
--to=zhouyanjie@wanyeetech.com \
--cc=ak@linux.intel.com \
--cc=aric.pzqi@ingenic.com \
--cc=devicetree@vger.kernel.org \
--cc=dongsheng.qiu@ingenic.com \
--cc=ebiederm@xmission.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mips@vger.kernel.org \
--cc=paul@crapouillou.net \
--cc=paulburton@kernel.org \
--cc=rick.tyliu@ingenic.com \
--cc=robh+dt@kernel.org \
--cc=sernia.zhou@foxmail.com \
--cc=tsbogend@alpha.franken.de \
--cc=yanfei.li@ingenic.com \
--cc=zhenwenjin@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).