linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Badhri Jagan Sridharan <badhri@google.com>
To: Guenter Roeck <linux@roeck-us.net>,
	Heikki Krogerus <heikki.krogerus@linux.intel.com>,
	Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org, linux-kernel@vger.kernel.org,
	Badhri Jagan Sridharan <badhri@google.com>
Subject: [PATCH v6 12/14] usb: typec: tcpm: Implement enabling Auto Discharge disconnect support
Date: Mon, 31 Aug 2020 19:59:25 -0700	[thread overview]
Message-ID: <20200901025927.3596190-13-badhri@google.com> (raw)
In-Reply-To: <20200901025927.3596190-1-badhri@google.com>

TCPCI spec allows TCPC hardware to autonomously discharge the vbus
capacitance upon disconnect. The expectation is that the TCPM enables
AutoDischargeDisconnect while entering SNK/SRC_ATTACHED states. Hardware
then automously discharges vbus when the vbus falls below a certain
threshold i.e. VBUS_SINK_DISCONNECT_THRESHOLD.

Apart from enabling the vbus discharge circuit, AutoDischargeDisconnect
is also used a flag to move TCPCI based TCPC implementations into
Attached.Snk/Attached.Src state as mentioned in
Figure 4-15. TCPC State Diagram before a Connection of the
USB Type-C Port Controller Interface Specification.
In such TCPC implementations, setting AutoDischargeDisconnect would
prevent TCPC into entering "Connection_Invalid" state as well.

Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
---
Changes since v1:
- Changing patch version to v6 to fix version number confusion.
---
 drivers/usb/typec/tcpm/tcpm.c | 74 +++++++++++++++++++++++++++++++++--
 include/linux/usb/tcpm.h      | 16 ++++++++
 2 files changed, 86 insertions(+), 4 deletions(-)

diff --git a/drivers/usb/typec/tcpm/tcpm.c b/drivers/usb/typec/tcpm/tcpm.c
index 083e7af107b2..7aca769727d8 100644
--- a/drivers/usb/typec/tcpm/tcpm.c
+++ b/drivers/usb/typec/tcpm/tcpm.c
@@ -1694,6 +1694,25 @@ static void tcpm_handle_alert(struct tcpm_port *port, const __le32 *payload,
 	}
 }
 
+static int tcpm_set_auto_vbus_discharge_threshold(struct tcpm_port *port, enum typec_role port_role,
+						  enum typec_pwr_opmode mode, bool pps_active,
+						  u32 requested_vbus_voltage)
+{
+	int ret;
+
+	if (!port->tcpc->set_auto_vbus_discharge_threshold)
+		return 0;
+
+	ret = port->tcpc->set_auto_vbus_discharge_threshold(port->tcpc, port_role, mode, pps_active,
+							    requested_vbus_voltage);
+	tcpm_log_force(port,
+		       "set_auto_vbus_discharge_threshold pwr_role:%s mode:%d pps_active:%c vbus:%u ret:%d",
+		       port_role == TYPEC_SINK ? "sink" : "source", mode, pps_active ? 'y' : 'n',
+		       requested_vbus_voltage, ret);
+
+	return ret;
+}
+
 static void tcpm_pd_data_request(struct tcpm_port *port,
 				 const struct pd_message *msg)
 {
@@ -1863,6 +1882,10 @@ static void tcpm_pd_ctrl_request(struct tcpm_port *port,
 						       port->current_limit,
 						       port->supply_voltage);
 				port->explicit_contract = true;
+				tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_SINK,
+								       TYPEC_PWR_MODE_PD,
+								       port->pps_data.active,
+								       port->supply_voltage);
 				tcpm_set_state(port, SNK_READY, 0);
 			} else {
 				/*
@@ -2777,8 +2800,14 @@ static int tcpm_src_attach(struct tcpm_port *port)
 	if (ret < 0)
 		return ret;
 
-	ret = tcpm_set_roles(port, true, TYPEC_SOURCE,
-			     tcpm_data_role_for_source(port));
+	if (port->tcpc->enable_auto_vbus_discharge) {
+		tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_SOURCE, TYPEC_PWR_MODE_USB,
+						       false, VSAFE5V);
+		ret = port->tcpc->enable_auto_vbus_discharge(port->tcpc, true);
+		tcpm_log_force(port, "enable vbus discharge ret:%d", ret);
+	}
+
+	ret = tcpm_set_roles(port, true, TYPEC_SOURCE, tcpm_data_role_for_sink(port));
 	if (ret < 0)
 		return ret;
 
@@ -2845,6 +2874,12 @@ static void tcpm_unregister_altmodes(struct tcpm_port *port)
 
 static void tcpm_reset_port(struct tcpm_port *port)
 {
+	int ret;
+
+	if (port->tcpc->enable_auto_vbus_discharge) {
+		ret = port->tcpc->enable_auto_vbus_discharge(port->tcpc, false);
+		tcpm_log_force(port, "Disable vbus discharge ret:%d", ret);
+	}
 	tcpm_unregister_altmodes(port);
 	tcpm_typec_disconnect(port);
 	port->attached = false;
@@ -2909,8 +2944,14 @@ static int tcpm_snk_attach(struct tcpm_port *port)
 	if (ret < 0)
 		return ret;
 
-	ret = tcpm_set_roles(port, true, TYPEC_SINK,
-			     tcpm_data_role_for_sink(port));
+	if (port->tcpc->enable_auto_vbus_discharge) {
+		tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_SINK, TYPEC_PWR_MODE_USB, false,
+						       VSAFE5V);
+		ret = port->tcpc->enable_auto_vbus_discharge(port->tcpc, true);
+		tcpm_log_force(port, "enable vbus discharge ret:%d", ret);
+	}
+
+	ret = tcpm_set_roles(port, true, TYPEC_SINK, tcpm_data_role_for_sink(port));
 	if (ret < 0)
 		return ret;
 
@@ -3470,6 +3511,8 @@ static void run_state_machine(struct tcpm_port *port)
 		 * drive VBUS to vSafe0V as shown in Figure 7-9.
 		 */
 		tcpm_set_vconn(port, false);
+		tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_SOURCE, TYPEC_PWR_MODE_USB,
+						       false, 0);
 		tcpm_set_vbus(port, false);
 		tcpm_set_roles(port, port->self_powered, TYPEC_SOURCE,
 			       tcpm_data_role_for_source(port));
@@ -3491,9 +3534,13 @@ static void run_state_machine(struct tcpm_port *port)
 		tcpm_set_vbus(port, true);
 		port->tcpc->set_pd_rx(port->tcpc, true);
 		tcpm_set_attached_state(port, true);
+		tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_SOURCE, TYPEC_PWR_MODE_USB,
+						       false, VSAFE5V);
 		tcpm_set_state(port, SRC_UNATTACHED, PD_T_PS_SOURCE_ON);
 		break;
 	case SNK_HARD_RESET_SINK_OFF:
+		tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_SINK, TYPEC_PWR_MODE_USB, false,
+						       0);
 		memset(&port->pps_data, 0, sizeof(port->pps_data));
 		tcpm_set_vconn(port, false);
 		if (port->pd_capable)
@@ -3536,6 +3583,8 @@ static void run_state_machine(struct tcpm_port *port)
 			tcpm_set_charge(port, true);
 		}
 		tcpm_set_attached_state(port, true);
+		tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_SINK, TYPEC_PWR_MODE_USB, false,
+						       VSAFE5V);
 		tcpm_set_state(port, SNK_STARTUP, 0);
 		break;
 
@@ -3637,6 +3686,12 @@ static void run_state_machine(struct tcpm_port *port)
 			tcpm_set_state(port, PR_SWAP_SNK_SRC_SINK_OFF, 0);
 		break;
 	case PR_SWAP_SRC_SNK_TRANSITION_OFF:
+		/*
+		 * Prevent vbus discharge circuit from turning on during PR_SWAP
+		 * as this is not a disconnect.
+		 */
+		tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_SOURCE, TYPEC_PWR_MODE_USB,
+						       port->pps_data.active, 0);
 		tcpm_set_vbus(port, false);
 		port->explicit_contract = false;
 		/* allow time for Vbus discharge, must be < tSrcSwapStdby */
@@ -3665,9 +3720,18 @@ static void run_state_machine(struct tcpm_port *port)
 		tcpm_set_state_cond(port, SNK_UNATTACHED, PD_T_PS_SOURCE_ON);
 		break;
 	case PR_SWAP_SRC_SNK_SINK_ON:
+		/* Set the vbus disconnect threshold for implicit contract */
+		tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_SINK, TYPEC_PWR_MODE_USB, false,
+						       VSAFE5V);
 		tcpm_set_state(port, SNK_STARTUP, 0);
 		break;
 	case PR_SWAP_SNK_SRC_SINK_OFF:
+		/*
+		 * Prevent vbus discharge circuit from turning on during PR_SWAP
+		 * as this is not a disconnect.
+		 */
+		tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_SINK, TYPEC_PWR_MODE_USB,
+						       port->pps_data.active, 0);
 		tcpm_set_charge(port, false);
 		tcpm_set_state(port, hard_reset_state(port),
 			       PD_T_PS_SOURCE_OFF);
@@ -3693,6 +3757,8 @@ static void run_state_machine(struct tcpm_port *port)
 		 */
 		tcpm_set_pwr_role(port, TYPEC_SOURCE);
 		tcpm_pd_send_control(port, PD_CTRL_PS_RDY);
+		tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_SOURCE, TYPEC_PWR_MODE_USB,
+						       false, VSAFE5V);
 		tcpm_set_state(port, SRC_STARTUP, PD_T_SWAP_SRC_START);
 		break;
 
diff --git a/include/linux/usb/tcpm.h b/include/linux/usb/tcpm.h
index 09762d26fa0c..a1707def51c3 100644
--- a/include/linux/usb/tcpm.h
+++ b/include/linux/usb/tcpm.h
@@ -83,6 +83,18 @@ enum tcpm_transmit_type {
  *		Optional; Called to enable/disable PD 3.0 fast role swap.
  *		Enabling frs is accessory dependent as not all PD3.0
  *		accessories support fast role swap.
+ * @enable_auto_vbus_discharge:
+ *		Optional; TCPCI spec based TCPC implementations can optionally
+ *		support hardware to autonomously dischrge vbus upon disconnecting
+ *		as sink or source. TCPM signals TCPC to enable the mechanism upon
+ *		entering connected state and signals disabling upon disconnect.
+ * @set_auto_vbus_discharge_threshold:
+ *		Mandatory when enable_auto_vbus_discharge is implemented. TCPM
+ *		calls this function to allow lower levels drivers to program the
+ *		vbus threshold voltage below which the vbus discharge circuit
+ *		will be turned on. requested_vbus_voltage is set to 0 when vbus
+ *		is going to disappear knowingly i.e. during PR_SWAP and
+ *		HARD_RESET etc.
  */
 struct tcpc_dev {
 	struct fwnode_handle *fwnode;
@@ -109,6 +121,10 @@ struct tcpc_dev {
 			   const struct pd_message *msg);
 	int (*set_bist_data)(struct tcpc_dev *dev, bool on);
 	int (*enable_frs)(struct tcpc_dev *dev, bool enable);
+	int (*enable_auto_vbus_discharge)(struct tcpc_dev *dev, bool enable);
+	int (*set_auto_vbus_discharge_threshold)(struct tcpc_dev *dev, enum typec_role port_role,
+						 enum typec_pwr_opmode mode, bool pps_active,
+						 u32 requested_vbus_voltage);
 };
 
 struct tcpm_port;
-- 
2.28.0.402.g5ffc5be6b7-goog


  parent reply	other threads:[~2020-09-01  3:00 UTC|newest]

Thread overview: 32+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-09-01  2:59 [PATCH v6 00/14] TCPM support for FRS and AutoDischarge Disconnect Badhri Jagan Sridharan
2020-09-01  2:59 ` [PATCH v6 01/14] usb: typec: tcpci: Add register definitions to tcpci Badhri Jagan Sridharan
2020-09-15 12:10   ` Heikki Krogerus
2020-09-01  2:59 ` [PATCH v6 02/14] usb: typec: tcpci: Add support when hidden tx registers are inaccessible Badhri Jagan Sridharan
2020-09-15 12:11   ` Heikki Krogerus
2020-09-01  2:59 ` [PATCH v6 03/14] usb: typec: tcpci: update ROLE_CONTROL for DRP Badhri Jagan Sridharan
2020-09-15 12:12   ` Heikki Krogerus
2020-09-01  2:59 ` [PATCH v6 04/14] usb: typec: tcpci: Add a getter method to retrieve tcpm_port reference Badhri Jagan Sridharan
2020-09-15 12:16   ` Heikki Krogerus
2020-09-01  2:59 ` [PATCH v6 05/14] usb: typec: tcpci: Add set_vbus tcpci callback Badhri Jagan Sridharan
2020-09-15 12:22   ` Heikki Krogerus
2020-09-16  9:07     ` Badhri Jagan Sridharan
2020-09-01  2:59 ` [PATCH v6 06/14] dt-bindings: usb: Maxim type-c controller device tree binding document Badhri Jagan Sridharan
2020-09-01  2:59 ` [PATCH v6 07/14] usb: typec: tcpci_maxim: Chip level TCPC driver Badhri Jagan Sridharan
2020-09-15 12:43   ` Heikki Krogerus
2020-09-16  9:34     ` Badhri Jagan Sridharan
2020-09-01  2:59 ` [PATCH v6 08/14] dt-bindings: connector: Add property to set initial current cap for FRS Badhri Jagan Sridharan
2020-09-01  2:59 ` [PATCH v6 09/14] usb: typec: tcpm: Add support for Sink Fast Role SWAP(FRS) Badhri Jagan Sridharan
2020-09-15 13:20   ` Heikki Krogerus
2020-09-17 10:23     ` Badhri Jagan Sridharan
2020-09-01  2:59 ` [PATCH v6 10/14] usb: typec: tcpci: Implement callbacks for FRS Badhri Jagan Sridharan
2020-09-15 13:23   ` Heikki Krogerus
2020-09-01  2:59 ` [PATCH v6 11/14] usb: typec: tcpci_maxim: Add support for Sink FRS Badhri Jagan Sridharan
2020-09-15 13:25   ` Heikki Krogerus
2020-09-01  2:59 ` Badhri Jagan Sridharan [this message]
2020-09-01  2:59 ` [PATCH v6 13/14] usb: typec: tcpci: Implement Auto discharge disconnect callbacks Badhri Jagan Sridharan
2020-09-01  2:59 ` [PATCH v6 14/14] usb: typec: tcpci_maxim: Implemnent set_auto_vbus_discharge_threshold Badhri Jagan Sridharan
2020-09-15 12:09 ` [PATCH v6 00/14] TCPM support for FRS and AutoDischarge Disconnect Heikki Krogerus
2020-09-15 16:57   ` Badhri Jagan Sridharan
2020-09-15 13:33 ` Heikki Krogerus
2020-09-15 16:59   ` Badhri Jagan Sridharan
2020-09-16 11:05 ` Greg Kroah-Hartman

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20200901025927.3596190-13-badhri@google.com \
    --to=badhri@google.com \
    --cc=gregkh@linuxfoundation.org \
    --cc=heikki.krogerus@linux.intel.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-usb@vger.kernel.org \
    --cc=linux@roeck-us.net \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).